Search Documents

By A. Giblett, J. Shuttleworth, R. Dunne

In a previous paper (Dunne, Martins, Goulsbra, Chittenden 1997), the new gravity circuits at Telfer Gold Mine, which incor­porate Knelson centrifugal separators in both the sulphide and oxides, are described. The advantages of the new circuits over the replaced spiral ( oxide circuit) and jig (sulphide circuit) were discussed, as were the improvements in gravity gold recovety. It is of note that the installation of the centrifugal separators in themselves did not result in increased gold recovery. The realisa­tion that changes in gold room practices are required to take advan­tage of the increased fine gold recovery from the Knelson concen­trator was an important step towards improved gravity gold recov­ery. This was achieved by increasing the time taken to treat the Knelson concentrate on the shaking table in the gold room. Although this increased gold recove1y, it was found that the table tailings, especially from the sulphide circuit, still contained high values of gold. In an effort to ascertain ways in which gravity gold recovery could be fu1iher improved, a sample of the sulphide table tailings was sent to the Oretest Laboratory in Perth for testwork. The results from this program are discussed in this paper.

Jan 1, 1998

By Marcel Haffen, Jean Janin

The purpose of grouting is to modify the permeability and strength characteristics of the subsoil in such a way that the planned structure can be efficiently constructed at a given location. This technique, which originally underwent considerable development in the field of dams construction is constantly evolving and it becomes more and more important in urban zones of intensive underground development for projects such as transport tunnels, stations, car parks, ect. Grouting becomes more and more indispensable whatever the natural characteristics of that subsoil ; such is the case particularly when the planned work runs through cohesionless granular soils, usually water-bearing such as alluvium, sands, disturbed ground, fill material, etc. The selection of the grouting method and the extent of treatment required at depends on two fundamental factors. 1º) nature and behaviour of subsoil to be treated. There is no need to stress the necessary of a good knowledge of geotechnical, hydrological and chemical characteristics of the ground to be treated. At the present time the specialists in these fields have available numerous methods of analysis, either laboratory or field tests, which enable to evolve a suitable treatment.

Jan 1, 1997

By F. -U. Schneider, F. Wellenkamp

Based on previous investigations of ultrafine comminution in planetary ball mills, a new centrifugal mill has been developed which permits similar high stress conditions. Because this new type of mill is equipped with an immobile chamber, devices for measuring energy, for cooling the milling vessel, as well as, in continuous operation, for material feed and discharge can be more easily attached than to planetary ball mills. Observations of particle behaviour have shown that, in the case of dry grinding, most of the material is found on the mill walls even after short grinding times. Due to the fact that energy dissipation takes place mainly in the zone near the wall, a grinding system which reduces the amount of ball filling required is at an advantage.

Jan 1, 1995

By B. Hearn, O&apos

Falconbridge, Ltd. operates six mines (the strathcona, Fraser, Lockerby, Onaping, East and Kidd Creek) in the Sudbury and Timmins districts of northern Ontario (Fig. 1). These mines vary in depth to approximately 1500m and experience a wide variety of ground conditions. Problems of greatest concern include rockbursting, backfill pillar stability, wall and pillar stability, and the use of cable anchors. A study was initiated approximately two years ago to identify how numerical models could aid in the examination and possible understanding or solution of these problems. This paper discusses the use of numerical models at Falconbridge and describes a case history of their use in examination of rockbursting at the Strathcona Mine.

Jan 1, 1988

By S. Lu, J. P. Barta, T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate : 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3)Azospirillum had no effect on canopy cover.

Jan 1, 1999

By Winfield G. Wright, Greg P. Meeker, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

A really extensive acid sulfate-altered and mineralized rock in the southeast Red Mountains area is noted for its association with naturally occurring and mine-related acidic and metal-rich waters. Integrated geologic and aqueous geochemical studies demonstrate that the degree of metal mobilization and acid production in natural waters correlates well with the type of hydrothermally altered rock and structural features in which these water interact. Quartz-sericite-pyrite, quartz-alunite, and argillic alteration assemblages are associated with some of the most naturally acidic, high-metal waters in the study area; calcite-bearing propylitic rocks are related to the most pristine waters and buffer sulfate-rich, acidic waters produced by pyrite oxidation. Trace metals in natural waters are mostly derived from enargite, zinc-rich tetrahedrite and sphalerite. Pyrite oxidation contributes very little with respect to base-metals in these natural waters.

Jan 1, 2000

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone's ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986

By C. DeRossett, K. F. Unrug

Sedimentary rock fractures commonly occur in the vicinity of outcrops. Mine highwalls and highway cuts provide excellent views of these near-surface joint systems. This paper explains the origin, characterization, distribution and extent of the these joint systems with reference to the lithologic composition of the rocks. The practical implications of these joint systems on the operation of a mine are described. Included are discussions of the discontinuous deformation that results from surface subsidence, the stability of mine portals and near-outcrop underground operations, and the stability of highwalls when using highwall miners and strip operations. Some design procedures are recommended to minimize the problems encountered within mining areas having intense joint systems.

Jan 1, 1996

By R. M. Carland, F. F. Aplan

Six natural zeolites were evaluated for their ability to selectively remove heavy metal cations from solution. Ion selectivity was found to be Pb+2>Zn+2>Ni+2 and Cu+2>Co+2 from their respective solutions. The presence of K+, Ca+2 and Mg+2 in the actual waters to be used may seriously interfere with the ion exchange and elution of cations from zeolites. Zeolites were found not to be effective in removing precious metals from their cyanide solutions.

Jan 1, 1995

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Limited contracted to sink a 1500 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.5 ft) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (15 ft.) diameter double-drum hoist to sink the shaft with 12.5 tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1991

By C. A. Roberts

What are the benefits and limitations of financial analysis software as a decision making tool in the mining industry? Traditionally, the assumptions and simplifications imposed by complex and uncertain information have been viewed as the main obstacle to reaching an optimum decision. Recently, however, phenomena such as corporate culture and power structure have received increasing attention as significant influences on organizational decision making processes. Studies of these phenomena have suggested an alternative way of understanding decision making processes and an alternative view of the role played by computer analysis in such processes. This paper presents these two views of decision making, and examines what each implies about the role of financial analysis software as a decision making tool in the mining industry.

Jan 1, 1992

By Kalle Hakalehto

Automation and mechanization in mining has no value of its own. It has to be measured in economic terms or in Increased safety or in the utilization of deposits which otherwise were unavailable. The mechanization and automation of workphases in the mining and rock construction process has led to the decrease of manual work. This has had a very essential importance in the countries where the labor is expensive or where there has been difficulties in the availability of labor. The work has become much more efficient. We would like to argue that the need of mechanization has been initiated mostly from the above mentioned reasons. The origin has seldom been the "process" approach or the real need or will to change the way mining is done. Through mechanization bigger unit sizes of machines and operations have become possible and better efficiency is achieved. This has led to new problems as well, but in most cases they have been solved so that better and more economic outcome than before has been the end result. The changes have thus been justified. It is perhaps feasible to state already at this stage that we see that the mechanization andautomation steps in the difficult conditions of mining have been remarkable. There is not a slightest underestimation of the achievements and importance of this development in our mind. Where we are to- day is the result of the experience, know-how and technological excellency of all the parties involved. The natural approach to automation has been through mechanization and automation of individual unit operations and machines. This has been the way as well in manufacturing industry as in mining. There may not have been any other way. The other presentations in this session tell us very clearly of the approach .which the machine manufacturers have taken. They have not done it alone but 'most of the initiatives have come from them. A good use of their present achievements gives many possibilities to increase the, efficiency in mining. We would, however, like to extend the view one step further to the future:

Jan 1, 1989

By Raymond F. Mikesell

This paper evaluates the contributions of "third parties" to surplus capacity in the world metals industries in the 1980s. Special attention is given to the role of international development agencies, such as the World Bank, that have made project loans to state mining enterprises. The paper also reviews the contributions to surplus capacity of the International Monetary Fund and evaluates the large volume of credits from commercial banks to developing countries. Although the credits to Third World countries during the 1970s facilitated the expansion of mining capacity in those countries, no one source of financing can be held responsible for a significant portion of the expansion.

Jan 1, 1989

By Jack S. McPartland, Gene E. McClelland

It is advisable, for any heap leach project, to develop an historical metallurgical data base to predict production heap performance before ore is mined and placed onto the heap. A data base would include results from: interval assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples; and those results plus column leach test data on diamond drill core or bulk ore composites. Subsequent larger scale heap leach test data can then be compared to the historical data base, to blast hole composite data during mining, and eventually to production data. This paper does not discuss metallurgical comparisons between assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples, but does discuss metallurgical comparisons from bottle roll tests, laboratory scale column leach tests, and pilot scale heap leach tests on core and bulk ore samples with operating data for three U.S. commercially producing heap leach operations. Provided that representative core or bulk samples are used for evaluation, heap leach test results accurately predict or understate the success of the commercial operation and remove most of the uncertainty from the investment decision.

Jan 1, 1990

By D. Erik Spiller

Introduction The recovery of precious metals from ore can generally be accomplished using either gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems which employ leaching as the primary unit operation. A brief discussion of modern gravity concentration equipment is also presented.

Jan 1, 1984

By Richard J. Frechette

Final reclamation of mine tailings impoundments typically involves addressing the broad issues of surface stabilization and water management. Surface stabilization includes immobilizing the tailings particles and providing long-term protection of the containment facility. Water management typically includes provisions for handling both the external water (rainfall and runoff) and the internal water (pore fluids). Wet tailings disposal facilities, and sites with limited access and steep topography, present challenges to implementing effective surface stabilization and water management plans. This paper presents a generalized discussion of the approach to tailings impoundment reclamation based on project experience.

Jan 1, 1995

By Bruce D. Hansen

The complexity of large geographically diverse or multicommodity mining companies requires a corporate structure, which provides the maximum long-term effectiveness. Structure models exist along the spectrum of centralization to decentralization. This paper examines the trade-offs of flexibility, cost, decision making, consistent strategies, and corporate control associated with different structural models as applied to mining companies. The mining industry typically lends itself to a business unit model. However, the degree of decentralization depends on size, proximal operations, technical complexity, product mix, geographic spread, mining methods employed, and the inherent capabilities of an organization.

Jan 1, 2001

By Chinmoy Sarkar

Mining organizations have been trying to employ best practices at exploration, exploitation and processing level to increase productivity in the supply chain. Traditional techniques of cost control can no longer meet the ambitious target of mine managers. An integrated perspective of Mining Value Chain with enterprise-wide application of information technology (IT) ensures the ability of every mining processes to improve energy, land, capital and labour resource performance while continuing to cut costs and achieve profitability. IT offers enormous potential in mining industry at shaping entirely new opportunities to create value. This paper characterizes important entities of Mining Value Chain and attempts to provide a vision on how IT can transform the mindsets of industry managers addressing the needs of the customers.

Jan 1, 2002

By S. K. Kawatra, T. C. Eisele

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. To reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, because different measures are required for reducing entrainment, locked particle flotation or true hydrophobic flotation. In this paper, evidence is presented that suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite; instead, the bulk of the recovered pyrite results either from simple entrainment or from being physically locked with floatable coal particles.

Jan 1, 1993

By Osvaldo Bascur

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. This results in significant deterioration in the ability to maintain a "smart" operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. This paper describes the use of Internet technologies with plant data. Examples are drawn from existing industrial sites. Users must project where this technology will lead - standing still is the most dangerous philosophy and the only one guaranteed to be obsolete. These examples show the way to leverage existing workers with information technology.

Jan 1, 2000