Search Documents

By William F. Ryan, Paul T. Gribbon

With the rise in construction claims in public works contracting over the years, the use of Dispute Review Boards (DRB’s) in underground construction contracts has become quite common. However, in order for the DRB process to be an effective tool, there must be complete trust and confidence in the Board members and their adopted procedures by both the owner and contractor. This can be difficult in an industry where Board members and contractors may be well known to each other, while an owner maybe involved in a large complex underground project only occasionally. Using case histories, this paper will discuss some recent experiences with the DRB process from an owner’s perspective.

Jan 1, 2003

By A. L. Putz, G. Ladouceur, A. R. Laplante

A laboratory centrifugal concentrator was used to evaluate two gravity circuit configurations treating a flash flotation concentrate at a Canadian gold mill. The Initial circuit consisted of a 76 cm (30 Inch) plant Knelson Concentrator (PKC) for coarse gold removal. Later, a hydroseparator and spiral were Installed, with the hydroseparator underflow feeding the spiral and the spiral tailings plus hydroseparator overfiow reporting to a 51 cm (20 Inch) PKC. Gold recovery In the 76 cm PKC averaged 45%. Gold was recovered consistently In all size fractions greater than 38 µm, where recovery dropped to 22% for the -38 µm material. Changing the circuit to Include the hydroseparator and spiral decreased the Knelson unit recovery to less than 17%. The decrease was attributed to the spiral which recovered much of the free gold ahead of the Knelson and to changes In the mill feed (free gold portions were finer and less abundant). The spiral demonstrated erratic behaviour although It still recovered significant coarse gold (+75 µm) yielding unit recoveries of 18-44%. Although mechanical difficulties were experienced with the 76 cm PKC, Its performance was superior to that of the hydroseparator, spiral and 51 cm PKC configuration. Much of the gold In the ball mill recirculating load was found to be too coarse for significant recovery In the flash flotation cell and should be recovered by gravity from the cyclone underflow or ball mill discharge. The LKC proved to be a successful device to evaluate gravity recoverable gold content. Dilution of test samples with silica further enhanced this methodology.

Jan 1, 1993

By D. J. Hutchinson, S. Nickson

Cable bolts are used as a means of rock support around underground excavations in many mines across Canada and around the world. A substantial body of research on cable bolting was conducted at a number of Canadian universities and mines from the mid-1980s through the 1990s. Since then, research into selected areas of cable bolting practice has continued in Canada. The research has focussed on cable bolt instrumentation and on the inclusion of cable bolts in empirical stope design techniques. A review of cable bolting practice is now warranted at many mines. It has been five years since the completion of the previous substantial body of Canadian academic research and the associated advancement in understanding of cable bolt design, implementation and verification practice. Attempts were made at that time to transfer the new design procedures and performance assessment technologies to mine-site personnel. In some cases, this was effective, and ground control personnel continue to improve on their cable bolting practice at each specific mine site. However, at other sites, experienced people have moved on, and the new, less experienced personnel do not have access to the training or technical resources required to improve their understanding of the subject. In other cases, the technology was not transferred effectively to practitioners, with the result that substantial improvements can be made to the cable bolting practice at those mines. Guidelines for auditing cable bolting practice are provided in this paper. The guidelines include a discussion of the objectives of the audit, suggestions for audit procedure and a summary of the possible outcomes of a cable bolt audit. The objectives of an audit might include assessing the reasons for unexpected cable bolt failures, evaluating the quality of the installation procedures, quantifying the efficiency of the cable bolt system and assessing training requirements and procedures. A cable bolt audit should include consideration of all aspects of the cable bolting cycle, including the design, implementation and verification phases of the operation. At the end of the audit, a ranking should be assigned to the components of the cycle. The ranking system can then be used to identify items that require immediate attention, others that could be improved and others that are adequate. Following completion of a cable bolt audit, increased confidence in the support system and its application is generally, found, along with the potential for cost savings in many cases.

Jan 1, 2002

By Bok-youn Kim

Presently, mobile diesel equipments contributes a lot in improving the economical feasibility of underground mining and tunneling operations. Even in Korea, quite a large number of diesel equipments is being applied to the underground workings already. This paper introduced the production procedure, characteristics and evaluation technology on diesel particulate matter(DPM) that is known as a carcinogen For easy measurement of DPM using laser dust monitor, the conversion factor(K) to gravimetric concentration was acquired. The field measurement of DPM was conducted to make a comparison between locally manufactured on-road equipments and imported equipments specially designed for underground use. According to the Government regulation revised h 1996, it was learned that the critical pollutants among the diesel exhaust is DPM instead of NOx which have been considered as a critical pollutants.

Jan 1, 1997

By G. Baudet, M. Save

Ethoxylated phosphoric ester surfactants were evaluated as collectors for flotation of carbonates from sedimentary phosphate ores, at slightly acidic pulp pH, using sulfuric acid or sodium fluorosilicate as a phosphate depressant. With 12 to 15 carbon atoms in the hydrophobic chain, maximum collecting power was observed for 9 to 10 ethylene oxide units. Only fine carbonates, ranging in size from about 20 to 160 µm or 40 to 200 µm, were effectively removed with phosphoric ester collectors. Utilization of seawater, or water of extremely high hardness, did not detrimentally affect selectivity. Silica, silicates, and residual fine carbonates can be separated in a second flotation stage, with primary amine as a collector. Coarse carbonates are separated by direct flotation of phosphate with fluoride ion as a phosphate activator and primary amine as a collector. In a seawater pulp, fluoride ion was not required. Typical examples of laboratory and pilot- scale test results are given to illustrate capabilities of the various flotation flowsheets.

Jan 1, 1999

By Daniel W. Kappes

Until recently, the general expectation among mining compa­nies and financial analysts has been that the price of gold would remain on a generally upward slope. The recent drop in the price of gold has caused many people to re-think the issue. Of course, the price of gold is singularly difficult to predict, so it is difficult to tell which concept is correct. In the present financial situation, however, many junior gold companies are faced with the reality that money is hard to raise, and many senior gold companies find that they are facing a period of corporate losses even though they own solidly producing mines, As engineering consultants, Kappes, Cassiday has recently received several requests to review conventional milling projects to see if heap leaching is a more viable option. In regard to straight financial criteria such as return on investment and net present value, the question is usually fairly easy to answer. However, corporate decisions must often be based on less definable criteria. For instance, new stock issues tend to be more successful if they are larger, which tends to favor milling operations over heap leaches. The corporate issues are often subjective and difficult to generalize about, so I will con­centrate in this paper on a few financial concepts.

Jan 1, 1998

By Charles Dr. Li, John Dr. Box

Selective flotation and adsorption behavior of zircon and rutile under hot soap conditions have been examined. Conditioning temperature, pH and washing steps were shown to control the flotation selectivity. The adsorption of the sodium soap of oleic acid at zircon- water and rutile-water interfaces was investigated through micro- electrophoresis and adsorption density measurements. The soap adsorption on the zircon surface increased markedly with increasing temperature due to a strong chemisorption/surface reaction, and was almost independent of pH. In contrast, the soap adsorption on rutile decreased at high pH values. A simple physisorption plus hydrophobic interaction appeared to be the principal mechanism for the soap adsorption on rutile at moderate temperatures (below ~70(C), beyond which it may change to chemisorption through an activation process. Water wash, particularly under acidic conditions (pH 2-3), of the rutile particles treated with soap, will lead to a desorption of the soap from the rutile surface by forming an acid salt precipitate.

Jan 1, 1995

By Guillermo Chong Díaz

A brief overview of industrial mineral exploration and exploitation in Chile is given. World class deposits of salt, lithium, nitrate, and iodine are present in northern Chile. The potential for further exploration and exploitation of these deposits, as well as the substantial reserves of other mineral commodities such as gypsum, anhydrite, volcanic rocks, and borates are discussed. In conclusion, industrial minerals mining in Chile has considerable potential, particularly as joint ventures between foreign and domestic companies. This has been demonstrated in the extraction of nitrates, lithium, iodine, and diatomites. However, as outlined in this paper, a number of factors need to be overcome before the true potential of the Chilean industrial minerals industry can be realized.

Jan 1, 2001

By D. M. Richards, A. D. MacPhail

Highland Valley Copper currently mines two low-grade ore bodies, Lornex and Valley. The partnership was formed in 1986. As a cost reduction measure, it was decided to use an in-pit crushing and conveying system to deliver the ore from the Valley Pit to the Lornex mill 3 km (1.8 miles) away and 175 m (575 ft) above the pit rim. The system uses two gyratory crushers that feed a series of conveyors to transport up to 130 kt/d (143,000 stpd) to the main stockpiles. This paper describes the performance of the in-pit crushing system as it is currently configured, as well as its evolution to date and future planned moves.

Jan 1, 1995

By D. Borrowman

Attrition of activated carbon in either the carbon-in-pulp (CIP) or carbon-in-leach (CIL) method of gold extraction can lead to, at the least, loss of expensive carbon that has to be made up, and at the worst, loss of both the carbon and any gold that was attached to it. Carbon attrition therefore represents a significant factor in both the efficiency and cost of the extraction process, and efforts to reduce attrition through process and equipment selection pay dividends. In evaluating carbon attrition potential, one would note that an individual carbon particle is in jeopardy virtually any time it is in motion. Since the motivators of this motion are primary centrifugal pumps, the purpose of this paper is to review the current styles of these pumps now in use and to examine their performance in minimizing carbon attrition.

Jan 1, 1992

By Ing. Alois Adamus, Ing. Václav Pošta, Ing. Lubomír Hájek

This paper reviews experiences connected with the use of nitrogen in the Czech coal industry. Special attention is focused on the first use nitrogen In the Czech Republic, it is probably the first case of fighting a mine fire using nitrogen in all the World. Discussion dwells on the present-day use of nitrogen, its sources, consumption, technological equipment, and the theoretical evaluation of nitrogen flushing.

Jan 1, 1995

By Pengfei Pan, Lianjun Guo, Houguang Sun, Donglin Xu, Chi Yang, Lihua Luan, Daning Zhang

"Based on the introduction of production technology of Anqian mining company, the stope ore mass distribution was analyzed in detail. The processability indexes of different grade ores were obtained with magnetic tube whereas the grinding time, concentrate grade and concentrate yield were measured. On the basis of digital ore deposit model which integrates ore natural attributes and processing attributes, two stages of ore blending optimization models were established. The first stage model sought the minimum of stope ore transportation cost under the restraints of output ore grade and stope production. The second stage was a system optional model that aimed at the furthest use of resources meeting not only the production constraints of mining field and process field but also ore beneficiability and the system output requirements of the concentrate grade. Lastly, the solving method of big M simplex algorithm was discussed and used in production. 1. Foreword China is the biggest iron ore consumption market. But most of iron ore deposits in china possess such features as low grade, complex compositions, weak magneticity and refractoriness. Under the current economic and technical conditions, rational utilization of low-grade and refractory iron ore is strongly needed to improve the utilization ratio of mineral resources and keep mine development sustainable (Lei 2011). In recent years, the domestic research institutions and mines made a lot of achievements of rational development and utilization of low grade iron ore resources in the beneficiation technology and equipment, high and low grade balance, cost and tax analysis (Wang and Zhao 2013, Zhang 2014, Zhu and Li 2014), laying the foundation for reasonable utilization of low grade iron ore. In this paper, Anqian mining company is taken as an example in which the production conditions, raw ore quality control, different grade of ore processability, and ore blending optimization mode in mining pit and processing plant were discussed to achieve the maximum utilization of low-grade refractory ores under the economical and reasonable conditions. This will ensure the stable operation of mining joint ventures and maximize the enterprise's production life and therefore, maximize the economic and social benefits in the enterprise life cycle."

Jan 1, 2017

By Deepak Malhotra

Following a severe recession in the early 1980's, mining companies have taken significant steps to improve metallurgy and reduce operating costs. They do not view chemical reagents and the long-term relationship with reagent producers the same way they did two decades ago. This paper discusses the general perspective of changes that have taken place over the years, especially with respect to cost of production, selling price and environmental constraints. A cooperative program between the consumers and producers of chemical reagents is recommended to understand each other's problems and identify the present and future needs of the mining industry. This approach will be beneficial to the long-term survival of both parties.

Jan 1, 1994

By N. Standish

Leonard and Newman (1989) describe concepts and plans of their forthcoming project designed to increase the bulk density of broken coal at various stages of its production and handling. This is an excellent idea and something that will certainly be useful to the coal mining industry worldwide. The authors seek to achieve bulk density increase by "reducing oreliminating, through chemical additives and engineering design, particle voidage and enhance particle consolidation trickling between the point of breakage (at the face) and loading (in the shuttle car) to increase coal bulk density and productivity." In the paper, they present some supporting results of bulk density versus moisture, with or without oil addition, from the steel industry research. Unfortunately, the paper contains many misconceptions and half-truths that detract from an otherwise excellent objective of the project of increasing bulk density by reducing particle voidage -"the bottom line evaluator." Correct.

Jan 1, 1990

By James Wm. White

Mine management now recognizes the value of computer-based truck-shovel dispatching in open pit mines. The key tangible benefits are substantial productivity increases with a given fleet of equipment or, alternately, significant reductions in equipment required to meet production quotas. In this work, we review the literature, report on efficient, optimal algorithms for haul truck dispatching in real-time, and briefly discuss methods used by various mines to evaluate productivity improvements over manual methods. We also present actual results obtained at thirteen mining operations around the world.

Jan 1, 1992

By Cheng Zhengbing, Sun Baoqi

This paper summarizes several chemical purification methods used for producing high-pure industrial minerals These methods, mainly including alkali melting, acid leaching, oxidation-reduction bleaching, are respectively used to eliminate the impurities such as silicates in graphite and diamond, ferric oxides in quartz sand or other valuable silicate minerals, colouring impurities in kaoline, barite and other minerals which are required to have a high-whiteness. The fundamentals of the chemical purification methods and some practical examples in China are introduced in the paper.

Jan 1, 1995

By Gary J. Goldberg

Through the early 1980s, surveying at Bingham Canyon required a great deal of repetitive and manual work. The advent of total station surveying equipment provided an opportunity to improve the speed and accuracy of surveying work while reducing manpower needs. An evaluation was made of total station systems and their ability to meet the surveying requirements of Bingham Canyon. This culminated in the purchase of a total station system as the mine reopened in 1986. The surveying department at Bingham Canyon during the early 1980s consisted of three, four-man crews using theodolites and self-leveling levels to perform the majority of the field work. Office work involved data reduction and hand plotting. Although hand-held programmable calculators were used, a great deal of time was spent manually transferring field notes to final calculations. After shutting down in early 1985, plans for start-up of mining operations in 1986 included a review of all aspects of the operation for cost and productivity improvement. Applying total station survey capabilities offered the potential to improve surveying accuracy and speed while reducing manpower needs.

Jan 1, 1990

By Hamid Maleki

A geotechnical monitoring program has been implemented at Energy West Mining Company for enhancing site-specific evaluation of longwall stress conditions. This program consists of underground measurements at five locations in two neighboring mining districts located in the Hiawatha and Blind Canyon Coal Seams under moderate to deep cover. Within the last five years, additional measurements, including data on recorded seismic events and face conditions, have been incorporated into the data collection program together with detailed geologic mapping of longwall gateroads. In conjunction with the measurement program, the authors have completed detailed boundary-element stress analyses of the mine plans. Models have been calibrated using the data from in-mine instrumentations and then routinely used for evaluation of mine plans at depths approaching 2,600-ft. The work has improved our understanding of load transfer, seismicity and yield pillar performance. It has identified areas of potential increased stress levels at certain longwall face positions and provided guidance to measures that could be considered to mitigate the potential for these increased stress levels.

Jan 1, 2009

By Louis L. Sirois, Kwang S. Moon

The flotation mechanisms of various flotation machines are briefly reviewed. The counter current column flotation mechanism is described in more detail. The merits of counter current column flotation include; improved metallurgical performance in terms of grade and recovery, effective cleaning action in the long cleaning zone with a blanket of fresh water, smaller floor space required due to the vertical configuration of a flotation column, low capital, operational, and maintenance costs due to the absence of moving parts and finally, easier flotation control due to the simplified circuit. The results of column flotation studies on various minerals and coal at CANMET are discussed. Some of the industrial experiences with the Canadian flotation column on various sulphides, oxides and coal are also presented.

Jan 1, 1988

By Wojciech Suwala

The transition from centrally planned to market economy affects methods of economic analysis. The models which were used in the past are riot valid presently, however they we're the seed which initialized the development of methods and applications. There is more than twenty years of experience in modeling of coal mining development. The first attempts were devoted to select the moment of mine construction commencement in order to meet planned output. In Poland significant development of such models began in 1986. Within the Central Research and Development Program there has been a continuous development of models. These models from econometric to optimization ones, were a certain sequence which, in accordance with changing economy system, led to the last version of the model. It is the most suitable one for contemporary problems of coal mining in present Polish circumstances.

Jan 1, 1992