Search Documents

By T. L. Heidrick

Late Cretaceous-early Tertiary Cordilleran porphyry Cu-Mo districts and their consanguineous Zn-Pb-Ag-Au-W vein and replacement deposits of the Rocky Mountain region comprise one of the largest, best studied, diverse, complex, puzzling, and richest compound metallogenic provinces on earth. A concise space-time definition of intermineral plate, regional and local structure-tectonic frameworks is crucial to deciphering their diachronous metallogeny and enhancing the explorationist's odds of future discovery.

Jan 1, 2013

By B. H. Gardner, S. Serata, D. Dickie

Since 1958, the Sifto Salt Division of Domtar, Inc., has operated the Goderich (Ontario) salt mine in Michigan basin bedded halite, with shafts located on Lake Huron's eastern bank. Initial mining utilized a conventional room and pi1lar pattern. However, roof deterioration developed. Incidence of progressive upward failure of saltback and over1yings ha1ey-do1omite layers intensified with entry aging. Studies were therefore initiated on new mining patterns utilizing the Serata Stress Control Method. Pursuant thereto, three test areas, indicated in the mine plan of Fig. 1, were designed and excavated. Full conversion to Stress Control mining was effected in January, 1983. This paper focusses on the instrumentation work in the third test area. Test Area 3 was designed to validate the excavation geometry of the new stress-controlled main entry system. The testing of that design was accomplished, in part, by comprehensive in situ stress, property, and deformation measurements on the performance of the model main entry section of Test Area 3. The paper describes: (1) the theoretical background of the SPDR/Stress Control Method; (2) specific problems and objectives addressed by the 1983 program of in situ measurements, (3) measurement results; and (4) conclusions drawn therefrom.

Jan 1, 1986

By Werner A. Dürrfeld

The Bullflex® System was introduced as a substitute for timber and debris lagging in mines and to create an in-situ early-stage interlocking effect between steel supports and the rock wall. As deplacement and/or disintegration of strata and of rock beds is to be avoided under all circumstances - following the ideas of NATM-steel support can only be loaded to the maximum when point load is avoided and ideal bedding of the rock is maintained.

Jan 1, 1981

With commodity prices rising again and market conditions stabilizing, the Metals Economics Group (MEG) found that most mining companies increased their exploration budgets in 2010. In the groups 21st edition of the Corporate Exploration Strategies (CES), MEG found a 44-percent rise in the estimated worldwide exploration total for 2010. MEG found that the estimated total 2010 budget for nonferrous metals exploration reached $12.1 billion, reinstating almost two-thirds of the industry?s $6 billion in cuts to exploration in 2009. Nonferrous exploration refers to expenditures related to precious and base metals, diamonds, uranium and some industrial minerals; it excludes iron ore, aluminum, coal, and oil and gas. In 2008, exploration budgets were at an all-time high of $14.4 billion. This capped a six-year run in which budgets rose. In 2009, nonferrous exploration budgets dropped 42 percent in 2009 as the global economic crisis and declining prices for almost all commodities took their toll on the industry. Metals prices - the primary driver of exploration spending - have improved markedly since bottoming in early 2009, and have traded well above their long-term trends throughout 2010. In response, major, intermediate and junior companies have all increased their aggregate exploration allocations in 2010. In particular, the significant improvement in the availability of equity financings for the juniors over the past 12 to 18 months has allowed this group to account for the largest share of the overall increase in exploration spending this year.

Jan 1, 2011

By D. A. Day, H. L. Marsh, P. J. Stephens, C. A. Wiggins

Lightweight cellular grout backfill behind pipe-in-tunnel has been gaining increased acceptance in the tunneling industry and has proved to be both practical and economical. Two successfully constructed projects, the Upper Scioto West Interceptor Sewer (USWIS), in Columbus, Ohio and the Benbrook Pipeline Tunnel Project in Fort Worth, Texas will be discussed. The projects represent two different but successful applications of lightweight cellular grout backfill. The USWIS placed the grout behind precast reinforced concrete pipe, in water bearing limestone, and in close proximity to residential water wells. The Benbrook Project placed grout behind 6,096 meters (20,000 feet) of steel pipe from just two locations, eliminating major surface disruption typically associated with the placement of pumped concrete.

Jan 1, 1999

By Jan E. Stache

Commercial software programs are being utilized to create and maintain a mine subsidence database in conjunction with the U.S. Bureau of mines research on mine subsidence in Illinois. A three-year survey net of monitored structures in an Illinois subdivision was entered as textual information (attributes), on an existing AutoCAD drawing. These attributes can be optionally displayed on the corresponding drawing or extracted as a text file for import to a database program. The database program, dBASEIV, allows combinations of multiple database files for extensive querying capabilities. Subsurface database files can be merged with surface database files to enhance the effectiveness of surface response analyses in mine subsidence research. The geographic information system (GIS), pcARC/INFO, was chosen to integrate existing AutoCAD drawings and dBASEIV database files into a relational database with a graphical representation. The relational database allows users to update either the graphical representation or the database, with the changes being reflected automatically in its alternate format. The increased capacity, through use of a GIS, to query combinations of database files and have the results reflected graphically has significant potential for expediting mine subsidence research.

Jan 1, 1986

By Michael E. Kelahan, Glenn A. Gruber

A review of recent phosphate beneficiation developments shows that Flotaire cells, ranging from 0.20 m to 2.44 m in diameter, have been examined in pilot scale and commercial plants. Applications of the column cells have included sized feed fractions using anionic and cationic reagent systems. In plants where the Flotaire was installed as a test unit or as an optional circuit, its use has been largely discontinued. On the other hand, when management committed to installing the Flotaire as an integral part of the flowsheet, the performance expectations were met or exceeded.

Jan 1, 1988

By D. S. Choi

This paper presents the results of geomechanics work applied to the longwall operation. The mining method was successfully adapted to US mining conditions resulting in an improvement in safety and productivity. The paper deals with various geomechanics problems associated with geologic and mining conditions.

Jan 1, 1987

By Lynn B. Hales, Randy A. Ynchausti

Expert supervisory control strategies have been used for many years to improve operating revenues in comminution circuits. Typical improvements in capacity range from four to eight percent. Several case studies of results will be presented as well as a general discussion of the technologies used to achieve the improvements. Crushing. SAG milling and ball milling circuits will be discussed.

Jan 1, 1997

By L. Mao, R. Yoon

The thin film balance (TFB) technique was used to measure the equilibrium thicknesses of the water films formed between two oil phases. The measurements were conducted with dodecane at varying concentrations of dodecylammonium chloride, pH, and electrolyte concentration. The data obtained in the present work were used to calculate the surface forces acting between the two oil phases. The calculation was carried using the Extended-DLVO theory with the surface potentials calculated from the Gibbs adsorption isotherm. The results show that oil droplets suspended in water are hydrophobic and the hydrophobicity changes with surfactant and electrolyte concentrations.

Jan 1, 2004

By M. E. Gershon

Extensive efforts are under way toward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics, and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1987

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988

By C. Ptacek, D. Hiller, J. L. Janbor, H. Mccreadie

Between 1991 and 1994, metallurgical residues from a pressure-oxidation autoclave at the Campbell Au-quartz mine at Red Lake, northern Ontario, were neutralized with dolomite-rich flotation tailings and were deposited in a polyethylene-lined disposal area. Mineralogical analysis indicates that most of the As occurs as a crystalline ferric sulfarsenate, and some is associated with Fe oxides and with K-H3O jarosite. Field pore-water geochemical data from 1994 and 1995 showed increases in Fe(II) and As(III) concentrations, suggesting that the sulfarsenate and jarosite are dissolving; none of the discrete As phases included in a thermodynamic database limit dissolved-As concentrations, and these concentrations may continue to increase. These results demonstrate the potential for Fe and As loading through groundwater systems.

Jan 1, 1998

By L. E. Eary, Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapo-concentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1998

By Chester A. Rowland

La conminución de Ios minerales es, generalmente, una etapa de preparación de la alimentación para las subsiguientes etapas del proceso. La molienda, fase de conminución de productos finos, requiere una gran inversión de capital y frecuentemente es el área de máxima utilización de potencia y de materiales resistentes al desgaste. La molienda se produce normalmente en tambores rotativos que utilizan un medio de molienda que se pierde en la misma, al elevarse con la rotación del tambor, se rompe el mineral por combinación de los efectos de impacto, atrición y abrasión, hasta producir el producto especificado. El medio de molienda pueda ser: - El propio mineral (molienda autógena - primaria y secundaria). - Medio no metálico, natural o fabricado (pebbles) - Medio metálico (barras o bolas de acero) Este capítulo tratará de molinos de barras y bolas que utilicen medio metálico de molienda.

Jan 1, 1982

By C. Anderson, K. Nikkhah

This paper outlines the role of simulation software in design and operation of a typical metallurgical plant with mineral processing and hydrometallurgical units, to produce concentrate and pure metal. It addresses the role of simulation and mass balance software in the conceptual, feasibility and detailed design stages. It discusses the use of JKSimMet for sizing of mineral processing units, and METSIM and IDEAS for development of energy and mass balances. In detailed design of a plant, the complex interaction and variation in performance of various units makes it difficult to predict overall system performance and availability. Simulation is used to: assess operating strategies that affect surge capacities at various stages compare different ore types and mining strategies that affect concentrate product quality. optimize transportation logistics for raw materials, concentrate and metal products

Jan 1, 2001

By K. R. Weller, U. J. Sterns

The goal of most in-plant studies is to identify factors that limit overall plant performance. A major finding from such studies is that interactions between unit operations are always important, usually specific for a particular ore and plant combination, and are one of the limits to plant performance. Computer simulation based on process models developed from in-plant studies is a useful tool for identifying limits to performance and for estimating the effects of proposed changes at both pilot and industrial plant scales. Examples involving interactions between comminution and various separation and agglomeration processes are presented, and directions for future development discussed.

Jan 1, 1989

By Byron N. Cooper

The Revenue Act of 1926 provided for five simple categories of natural resources to have the benefit of depletion allowances. In the 1947 Revenue Act, the number was increased to twenty-five, and in the 1951 Revenue Act to fifty-four. Of this number, fourteen were allowed 5 per cent; nine, 10 per cent; twenty-nine, 15 per cent; one, 23 per cent; and one (oil and gas), 27.5 per cent. The 1951 Revenue Act created a host of difficulties, including application of the "end- use criterion" and determination of the commonly accepted meaning of such terms as limestone, dolomite, chemical- and metallurgical-grade limestone, marble, calcium carbonates, and magnesium carbonates. Dolomite, for example, was listed at 10 per cent depletion allowance, but without definition. In the great amount of litigation growing out of the 1951 Revenue Act and its administration, it became essential to understand the derivation and subsequent usage of these common geologic terms. One thing that became clear was that our definitions changed significantly between the time that the 1951 Revenue Act became law and the time that later cases were tried. Some geologists neglected to learn about first usages of such terms as metallurgical limestone, and about meanings that were applicable when the 1951 Revenue Act was written and passed. Legal meanings in this paper are discussed in the light of certain famous cases that have been tried and settled.

Jan 1, 1966

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By Bruce E. Nesbitt, Paul G. Lhotka

At Lupin mine gold is spatially and genetically linked to zones of hydrothermal alteration in iron-formation which are symmetrically developed adjacent to late Archean quartz veins. Immediately adjacent to the veins, coarse grained, typically gold- and sulfide-poor, calc-silicate rocks are often present. These rocks comprise hedenbergite + quartz ± grossular garnet ± epidote ± scheelite ± calcite. Sulfides (pyrrhotite, arsenopyrite and loellingite) and gold are concentrated in the next zone and occur with hornblende-rich rocks comprised of hornblende, quartz, hedenbergite and grunerite. Furthest from the veins are gold- and sulfide-poor, grunerite-rich iron formation comprising grunerite, quartz, hornblende and sometimes magnetite. Although the alteration assemblages have similarities with skarns, they develop in iron formation, and are at best indirectly related to intrusive igneous rocks. Geological and geochemical data clearly indicate the calc-silicate rocks are metasomatic in origin.

Jan 1, 1990