Search Documents

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By K. Koizumf, A. A. Cram, K. Whitchurch

The Expert Scheduling is a new, exciting method for scheduling underground and open-cut coal mines. A key feature of the Expert Scheduler is the adoption of an expert or artificial intelligence system. The expert system makes decisions regarding the schedule, such as which area should be mined. With existing scheduling systems these choices are made by the scheduling engineer. Developing one area may be better than another if it offers better quality or lower costs. Information the engineer considers in these decisions could be; • coal tonnage and quality targets, • equipment utilisation, • mining cost, • and other practical constraints. In expert scheduling a number of experts are appointed to make these decisions. A number of mining strategies are examined for each period. Information for each strategy is evaluated by "experts" and the "best" solution adopted. The method is based on the Blackboard Techniques. With this technique information is presented to "knowledge sources” or "experts" by the Blackboard Controller for their "opinions". These "opinions" are examined by the Blackboard Controller to select the best strategy. Engineers can readily add experts to the system, and modify the weighting of experts to suit mining conditions. Using an Expert Scheduler means that many schedule op- tions can be analysed quickly with full repeatability.

Jan 1, 1996

By Peter W. Willcocks

The Cyanide Regeneration Process (CRP) was developed by Golconda Engineering and Mining Services and installed at Golconda's Beaconsfield Gold Tailings Retreatment Project situated in Tasmania, Australia. The Tailings Project is a 1000 ton per day carbon-in-pulp treatment plant, feed for which consists of tailings material which is dredged from the Tamar River. The pulp is screened to remove debris, then cycloned to form two products. Underflow pulp is stored in a 350 ton bin and cyclone overflow passes to a thickener. The coarse pulp material is fed to the grinding circuit then rejoins the thickened slimes in the cyanide leach circuit. Gold is extracted by carbon-in-pulp techniques. The plant is sited in rolling, hilly country approximately 200 meters from the Tamar River. The residue disposal area is quite small consisting of four dams, totalling 42 acres. The regional climate is cool and wet with little evaporation; therefore, we anticipated a net increase in contained liquor, and subsequent storage problems. Our plan was to remove cyanide from the liquor prior to returning the detoxified solution to the river system. Such treatment was not required until midway through the second year of the project. Initial testwork on sample material indicated that destruction of cyanide by chlorine was the simple solution. Subsequent follow-up on actual plant liquor indicated a huge chlorine requirement due, we believe, to the substantial degradation of vegetable matter plus organic content from the marine environment. The cost of cyanide destruction could not be justified.

Jan 1, 1998

By Robert G. Ditchburn

The Mariana arc is an ~1,400-km-long intraoceanic arc that marks the southern extension of the Izu-Bonin arc, and is host to 62 ?volcanic centers? of which at least 27 (21 submarine) are hydrothermally, or volcanically active. A surface ship cruise in early 2003 mapped the distribution of hydrothermal plumes emanating from these centers, followed by remotely operated vehicle (ROV) cruises with ROPOS in 2004 and Jason II in 2006. With the exception of one volcano (East Diamante), none of the vent sites visited by the ROVs were host to sulfide mineralization. Rather, they were characterized by high sulfidation mineral assemblages dominated by native sulfur. The sulfur was seen marking the vicinity of vent sites, or as sulfur ?chimneys? (e.g., NW Eifuku and Nikko), or more spectacularly as ?lakes? of molten sulfur, either occupying the summit crater of the volcano (e.g., Nikko), or perched on the flanks of the volcano, near the summit (e.g., Daikoku). Gas (H2S and CO2) was discharging through the molten sulfur. Evidence for these lakes to have either been substantially ?deeper? in their recent past (e.g., Nikko), or existing at other volcanoes (e.g., Seamount ?X?) is given by remnant ?pillars? of native sulfur that are reminiscent of rock pillars in lava lakes found along mid-ocean ridges.

Jan 1, 2008

Anhydrite-based dam constructions, which have been implemented successfully in other geological formations, were investigated with regard to their suitability in salt mines. The laboratory investigations show that anhydrite-based building materials with suitable additives bind safely in spite of the high temperatures in salt mines which normally pre-vent hydration. The dependence of the compressive strength, swelling behavior, porosity and permeability upon the choice and ratio of binding material components and additives was determined. Based on the results of these investigations, a pilot-scale experiment was carried out at the GSF Research Mine Asse (Germany) using a mixture suitable for the prevailing conditions

Jan 1, 2004

In general, it cannot be assumed that the strength of coal pillars remains constant over long periods of time. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing the load-bearing capacity of the pillars. This paper discusses a unique approach to determining the time-dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15, and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar, and the strength profiles were determined for each hole using a borehole penetrometer. The strength data were treated statistically to establish time-dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 2012

By R. C. Ford

The advent of solvent extraction-electrowinning (SX-EW) technology for recovery of copper from low grade oxide ores has extended the operational lives of many historic mines in the western United States, and made many other orebodies economically viable worldwide. Many of these operations are mature and face closure within the next decade, depending on market conditions. Closure of a large copper heap leach operation has not been undertaken, and differs in some important chemical respects from closure of gold leach pads. Challenges for closure include prediction of solution chemistry and draindown characteristics, determining the benefit of cover placement in semi-arid climates and evaluation of solution management strategies once the economics of copper recovery are no longer favorable. This paper discusses issues pertinent to copper heap closure in semi-arid and arid climates, and strategies for their management.

Jan 1, 2000

By Nikolay M. Sirakov, Michael L. Feves, Rumen P. Mironov, Daniel R. Hack

Subsurface investigation of sand and gravel deposits has generally been limited to test pits and borings. These techniques are problematic in terms of the accuracy, usability, and cost of the final data. Innovations in the application of geophysics have been gaining acceptance in the aggregate industry, especially to determine depth to bedrock and the extent of uneconomic inclusions. This paper presents a system to optimize the processing and evaluation of electrical resistivity data. The system uses 3D separation, geometrical reconstruction, and visualization of subsurface objects.

Jan 1, 2002

Over the past few years, the School of Mines of Paris has carried out a program of research* on the grade-tonnage relationships in the border zones of porphyry copper deposits. The initial problem was quite difficult : how does the grade vary at the border of the known orebodies? Does it decrease regularly, or do some thresholds exist, where the grade diminishes abruptly? The answer to these questions have important repercussions on the prediction of the future reserves in the fringe of the orebodies. If the grade decreases regularly, very important reserves could exist; if not, there would be strong limitations to the possible recoverable reserves. The first step of our study was a critical study of previous work done on the subject. It appeared that, following Lasky's pioneering paper (Lasky, 1950), most of the authors used what we can call an historical approach to the problem. In this, the grade-tonnage relationships are calculated from the available figures for production and reserves and the results are then extrapolated to the future. The strong limitation of this model are brought out in this article.

Jan 1, 1982

By David Green

Power point slides

Jan 1, 1999

By Leonid P. Ni, Askar M. Kunayev

It is well known that processing of the high-silicon bauxites for obtaining alumina by the hydrochemical Bayer process is irrational due to the significant losses of alumina and alkali with red mud. The main source of losses of the mentioned compounds under the conditions of leaching by the Bayer process is the formation of difficultly soluble sodium alumosilicate of the composition Na20 .Al203, 2Si02 . n H20. A conventional method of an extra recovery of alumina as well as of regeneration of alkali out of red mud is the high-temperature sintering of the latter with soda and limestone with the subsequent leaching of sodium aluminate from the sinter by water or soda solution. A sequential version of the Bayer-sintering flow chart recommended for the prosessing of bauxites with an increased content of silica is based on this method. However, the sintering method is not the only alkaline method allowing to make an extra recovery of alumina likewise of alkali from red mud. Our investigations showed/I/, that the components mentioned can be recovered by a pure hydrochemical method of treating red mud with concentrated alkaline solutions, with lime (Ca0) being present, that was earlier succesfully used in the development of the hydrochemical method of processing nepheline rocks/2/. The possibility of extracting alumina and alkali from red mud is based on the reactions which can be schematically represented in the following way:

Jan 1, 1984

The feasibility of exploiting a mineral deposit by developing a surface mine is closely related to the environmental protection and land reclamation costs. This issue has utmost importance for West Macedonia Lignite Centre (WMLC) of Greece, where there is still a lot of interest for opening of new mines and for further development of the existing open-pits. The decision-making process in these cases can be based on a decision tree that takes into consideration the various cost components of environmental management, the alternative solutions, the environmental permits and the cost reports of environmental management actions carried out so far. Moreover, the mine planning procedure is affected indirectly by numerous uncertain environmental and socioeconomic parameters, such as the delays caused by the bureaucratic procedures and the settlement of arguments in the Court.

Jan 1, 2006

By Kotaro Ohga, Gota DEGUCHI, Kiyoshi HGUCHI

The situation of Japanes coal mine is in the severe enviroment, because the policy on coal mining has changed. Every year one or two coal mines will be foced to close. To continue the production of coal, we have to reduce the cost of production. Therefore, the mining by longwall method which is more than 250m was attempted at Taiheiyou Coal Mine to reduce the cost and this mining method have had successful results. To get successful results by this mining method, the controlling and prediction of gas emission from the longwall panel will be most important things. In this paper, the comparison of the predicted gas emission from the mining panel based on the measured gas content by using new device with the observed results is described.

Jan 1, 1993

By M. Quamrul Ahsan, Andrew Griffiths, Edward P. Jucevic

Heap leaching of precious metal ores using the cyanide process is extensively used in the Western U.S.A. for extracting gold. Consequently, the impact of cyanide in the spent heap is closely examined by environmental agencies and permitting authorities. Currently, many states require that all decomnissioned heaps be detoxified before abandonment. This paper describes a case study for detoxification of spent heaps at the ACH-Dayton Project using hydrogen peroxide. The chemistry of cyanide detoxification by hydrogen peroxide, together with simplicity of a detoxification operation, is discussed.

Jan 1, 1989

By Ellen S. Forbus

Reduction bleaching is used to improve the brightness and color of the kaolin pigments sold to the paper and speciality industries. The bleach re¬duces the iron oxide associated with kaolin deposits to a colorless form by the following reaction: Na2S2O42+ 6Fe+3 + 4 H2O -> 2 NaHSO4 + 6Fe+2 + 6H+ (Conley et al., 1964). At present, sodium hydrosulfite is used by the kaolin industry as the reductive bleach. It is often purchased commercially as a liquid solution and added into an acidified slurry. Before the use of commercial sodium hydrosulfite, kaolin plants manufactured zinc hydrosulfite on site by adding zinc dust to sulfurous acid made by passing SO2 gas into water. This process was abandoned in the 1970s due to environmental concerns about zinc in waste waters. In the 1970s, Engelhard patented a process that made sodium hydrosulfate from an iron hydrosulfate (Tiethof, 1978). Difficulties with separating the iron hydroxide byproduct from the bleach and a decrease in the cost of commercial bleach caused the project to be abandoned.

Jan 1, 1993

By P. Bevilacqua, G. Ferrara, M. C. Williams, T. P. Meloy

Tabling is an old environmentally friendly separation unit operation. This paper models shaking tables and explores the action and design of riffles on shaking tables. By reassessing riffle shape and riffle patterns, significant improvements in tabling performance appear feasible. While table sales appear at their nadir, a high-tech environmentally friendly table may have a significant market in the coming decade. Riffles on a shaking table impact particle separation. Particles are affected by riffles and their exit position on the table is dramatically changed, Riffle shape determines how much the riffle will influence a given material. Moreover, riffle patterns influence the concentration of a given material and its exit points on a table. This effect of riffle placement and design is modeled in a spreadsheet. Major performance and separation improvements may he expected by improved table design. Two physical laws of tabling have been derived. These laws aid in the design of sophisticated high-tech tables.

Jan 1, 1995

By A. C. Lyons, A. J. Reed

INTRODUCTION A trend which is obvious in the United Kingdom and is thought to be evident in other parts of the Western world is the disproportionate rise in the cost of tunnel mining labour compared with other tunnel cost increases. This disproportionate increase in labour costs has been accompanied by, and may be the result of, a shortage of skilled working labour. To combat this problem there has been a steady increase in the use of machines for excavation and for the erection of tunnel linings to keep the amount of skilled labour working below ground to a minimum. The typical tunnelling cycle, where the ground needs continuous support can be excavation, temporary support, temporary lining, grouting and permanent lining. It is obviously an advantage to combine as many of these operations as possible and carry out as much as possible by machine. Machines have been developed which will, either alone or used in combination with a shield, excavate and, when necessary, temporarily support the excavation. If a segmental lining is used, it can be so designed that it will form the permanent lining and reduce the cycle time and skilled labour requirement to a minimum. In cases in which the ground can be cut accurately to a smooth profile and will stand without support for a sufficient time, the lining can be expanded against the ground and the necessity of grouting eliminated. In cases in which ground will not stand without support, the usual method is to use a bolted lining and to grout behind it preferably as the shield is shoved forward. Whichever technique is used (this is largely determined by the ground) it is an advantage to make the segments as large

Jan 1, 1974

By Jürgen Lotze

Previously (1981), it was shown that the fiscal policy practised by some IBA-member countries is mainly responsible for a significant shift of known bauxite resources into higher processing-cost categories. The possible impact of politically imposed fiscal costs on the competitiveness of relevant bauxite resources is investigated in detail by means of a model calculation procedure.

Jan 1, 1984

By F. C. Nicolli, J. P. Barbosa, P. S. M. Soares, A. V. Estevez

INTRODUCTION Spent household dry cell batteries are frequently disposed of with metropolitan wastestream (MSW) in landfills where they can leak due to handling or aging. Frequent rain and sun cycles, especially in tropical environments, coupled to the action of leachate, dissolve their metal constituents which will eventually reach rivers, lakes and underground water. It is well known that some of these metals are fundamental to sustain life and that is why living organisms concentrate them through their metabolism, but it has been also recognized that beyond specific limits they can definitely be deleterious to the environment. In other words, high concentration of heavy metals are proven to cause chronic or acute diseases and toxic reactions, by acting on mammals' kidneys, liver and nervous system. In addition, some metals frequently used in household batteries, as mercury and cadmium, are said to be carcinogenic (Landis et al. 1995, Silva et al. 1988). Occasionally, plants to treat MSW are coupled to compost production. Household batteries present in MSW can be dragged into these plants, contaminating their products and eventually reaching vegetables making them not proper to consume by people and animals. Alternatively, batteries are also conveyed to incinerators and burned, throwing into the atmosphere volatile species. These can either act as contaminants as toxic vapor species or be delivered by winds and scavenged by rains contaminating soils and water far away from their source. In conclusion, despite the treatment applied to MSW, one can say that battery residues are potentially environmentally hazardous. The careful assessment of the environmental impact caused by residues of household batteries it is not an easy task and it can be referred as a multivariable problem. First, many different household batteries are produced by industry and the potential environmental hazard associated to their disposal depends primarily on the type of battery and manufacturer's technology. These characteristics will dictate how resistant the battery case is to handling and the

Jan 1, 1998

By Sean E. Armstrong, Deepak Malhotra

The current trend in gold ore processing is the development of lower grade or highly refractory deposits. The perplexity of treating low grade oxidized ores has been adequately addressed by heap leach technology. However, refractory gold ores are very difficult to positively characterize the gold association within the mineral matrix. Gold accompanied with refractory sulfitlc or carbonaceous mineralization can often be sub­micron In size and occur interstitially. Mineralogical examination of these ores Is difficult, expensive, and occasionally Inconclusive. Hence, the metallurgist Is given little information for the selection of processing alternatives. The purpose of this paper Is to demonstrate the use of diagnostic leach procedures to assist the metallurgist' s decision-making process to solve some of these problems. By sequentially liberating and/or leaching gold associated with specific minerals, the amount of recoverable gold in each stage can be determined. Through careful interpretation of the results obtained by diagnostic leaching, the metallurgist can devise a flowsheet for treating the ore or solve a problem at an existing plant

Jan 1, 1992