Search Documents

By T. van Sandwijk, G. Van Weert, E. Molleman

This paper reports on test work that explored the dissolution/precipitation reaction: ZnS + 2HCl - ZnC12 + H2S, which is part of a process used in the production of pure ZnS. The research focused on the influence of proton activity on the dissolution of zinc concentrates obtained from the Brunswick Mine No. 12 in Canada (Brunswick Mining & Smelting); the Red Dog deposit in Alaska (Cominco Ltd.); and the Tara deposit in Ireland (Outukumpu Zinc). A comparison between the results of the experimental dissolution as a function of pH and the dissolution predicted by thermodynamics suggest that the three concentrates contained sig¬nificant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1999

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By John M. Ackerman

INTRODUCTION In the spring of 1988 the Joint Venture of Freeport-McMoran Resource Partners, Limited Partnership, IMC Fertilizer Inc, and Homestake Mining Co. was awarded the sulphur lease for Main Pass Block 299, lease number OCS-G 9372. This was one of eleven leases awarded to the Joint Venturers. Following the initial discovery wells in December 1988, a program of delineation drilling confirmed proven sulphur reserves of 67 million long tons. Proven, recoverable oil and gas reserves are 39.4 million barrels and 7.2 billion cubic feet, respectively. Development of the sulphur mine was given approval as a fast-track project by the Joint Venturers in 1989. The oil and gas reserves were acquired from the original hydrocarbon lessee in 1990 and given fast- track status immediately. Fast-track for these projects meant design and engineering would not be complete before construction began JOINT VENTURE The Main Pass Joint Venture is one of thirteen joint ventures formed between Freeport and three other companies - IMC Fertilizer, Inc., Felmont Oil Corporation, a wholly owned subsidiary of Homestake Mining Co., and Texasgulf Minerals and Metals Co. Felmont has subsequently changed its name to Homestake Sulphur Co. and Texasgulf assigned their interests in the three leases they participated in to their parent company. Texasgulf did not participate in the Main Pass 299 joint venture. Joint venture negotiations, anticipating a lease sale in mid-1988, began in December of 1987. This Joint Venture was the first of its kind; created to acquire offshore leases, explore, develop and mine sulphur. The Minerals Management Service announced a lease sale date of February 24, 1988 on the first business day of 1988. This greatly accelerated the joint venture negotiations. Of the thirteen leases the Joint Ventures bid on, eleven were awarded. Freeport holds its interest in all the leases through its ownership interest in Freeport-McMoRan Resource Partners, Limited Partnership, and Resource Partners is the operator on all of the leases. The Main Pass joint venture percentage ownership is: 58.33 Freeport-McMoRan Resource Partners 25.00 IMC Fertilizer, Inc. 16.67 Homestake Sulphur Co. 100.00 The Main Pass Joint Venture paid $3,401,757 for the Main Pass lease and will pay a royalty of 12.5 percent of production value to the MMS . LOCATION The Main Pass mine complex is located in the Gulf of Mexico, in U. S. federal waters, about 27 kilometers (17 miles) east of Venice, Louisiana or 140 kilometers south east of New Orleans, Louisiana. It is situated in about 63 meters (210 feet) of water. HISTORY The Minerals Management Service (MMS) of the United States Department of the Interior administers the mineral properties of the United States located in federal waters. Periodically the MMS holds lease sales of blocks under its jurisdiction. Prior to the offshore discoveries of sulphur associated with salt domes leased for hydrocarbons, the MMS leased blocks with all minerals including hydrocarbons awarded to the successful bidder for the block. In 1963 MMS held the first lease sale of blocks specifically for sulphur. This sale was followed by a similar sale in

Jan 1, 1992

By Harold Wagner, Prakash Donde, Larry H. Heflin

INTRODUCTION The Washington Metropolitan Area Transit Authority is responsible for the planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. Some 117 kilometers (72.8 miles) of this system is in operation and contains 30.6 route-kilometers (19 miles) of rock tunneling. To complete the planned system an additional 1.6 kilometers (1.0 miles) of single track tunnels in rock are planned and additional contracts will consist of 4 kilometers (2.5 miles) of twin tunnel, resulting in 8 additional linear kilometers (5 miles) of single track tunnel contracts yet to be offered in soft ground. Three recent contracts in soft ground included the New Austrian Tunneling Method (NATM), along with conventional tunneling, as a bid option. Section E5a, Fort Totten Station and Tunnels, was the only one of the three to be constructed using the NATM option. This is the first application of the New Austrian Tunneling Method in soft ground in the United States. This paper will concentrate on the Fort Totten Station chamber NATM design, construction, and the instrumentation readings and evaluations which lead to an engineering back analysis which allowed a refinement of the bid design, resulting in a faster, more efficient construction. Design of the Fort Totten Station and Lines was done by Sheladia Associates. The design team included Greiner Engineering and Jenny Engineering with Mayreder-Consult of Austria, who was responsible for NATM design and NATM construction consultation.

Jan 1, 1991

By Victor J. Scaravilli

This report is based on experience developed on the construction of one contract for the Buffalo, New York subway. The Buffalo subway is under construction for the Niagara Frontier Transportation Authority and is called the LRRT-Light Rail Rapid Transit or more commonly the Metro. The Initial Route of the Buffalo subway construction started early in 1979 and is scheduled for completion in May, 1984. The initial system includes 5.2 miles of underground construction, 1.3 miles at grade for a total of 6.5 miles of subway system. A total of fourteen stations, eight underground and six at grade are included on the system. The Initial Route has a planned expansion to 17.3 miles in the future. On January 15, 1979, a Joint Venture of S & M Constructors, Inc., Solon, Ohio, James McHugh Construction Co., Chicago, Illinois, and Kenny Construction Company, Wheeling, Illinois, was awarded contract 100031, the Line Tunnels from Amherst Street to South Campus in northcentral Buffalo between Delaware Park and the State University, (see Fig. 1, Location Plan) This $35,000,000.00 contract was designed by Hatch Associates Consultants, Inc., Buffalo, N.Y. The Notice to Proceed was issued January 15, 1979 and the scheduled completion date is August 18, 1981. The project consists of two parallel rock tunnels with a minimum excavated diam of 18 ft 0 in. and a final concrete lining of 16 ft 0 in. diam. The tunnels total 14,630 linear ft. In addition to the tunnels, contract C-31 includes four shafts, an underground pump station, three cross passage connections, and other minor work items. (see Fig. 2, C-31 Project Plan and Profile) The tunnels were constructed primarily within the Bertie Formation, an approximately 50 foot thick moderately fractured to massive, dolo-

Jan 1, 1981

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

By Harold L. Lovell

The current interest in sulfur recovery from coal measures is indicated by a recent report prepared for the Public Health Service (1) It was noted that the concentration of pyrites to a product containing 42-48 percent sulfur should be relatively easy with present equipment. It was also pointed out that a utility potential exists for the high-grade iron concentrate which results as a by-product of the consumption of pyrites in the acid-making process. However, economics, marketing characteristics, location, transportation, pyrite levels and coal characteristics all strongly influence the feasibility of fostering industrial development of such processes. The extent of pyrite recovery and product quality is intimately related to pyrite particle size and its degree of liberation, a consideration usually given greater emphasis in metal ore preparation than in processing coals. Consequently, fine crushing to nearly 20 mesh probably will be essential for maximum practical processing. It appears that any process separating pyrites from a coal must involve a reprocessing of the normal preparation plant refuse, although some yields can be attained from certain existing operations as products from, a shaking table or a jig. Further, the existence of millions of tons of coal refuse cannot be ignored as a mined source of raw materials. The recovery of saleable products from such wastes, although untried on a large scale under current conditions, not only offers a realistic source of sulfur but also would achieve a secondary refuse with the minimal contents of substances which incite and propagate the burning of organic and inorganic combustibles. These silicate materials, thus beneficiated, also offer some potential for economic utilization. Some significant tonnages of pyrites have been produced from coal measures in the past, but the experience was, in general, not consistent with current coal preparation practice. The processes involved did not include cyclones and heavy media; nor were they carries out under the sociological environment concerned with pollution as exists today.

Jan 1, 1967

By William P. Lorenz

The paper describes a uranium by-product recovery plant operating within a copper leach, solvent extraction, and electrowinning circuit. The operation is unique because it is integrated into the main process stream of the copper circuit The plant processes 1408 m3/h of copper solutions containing about 10 mg/L of uranium. An Eluex type process was selected due to its compatibility with the copper leach plant. The paper includes an overview of the copper circuit

Jan 1, 1983

By O. Ofor

Finely-ground hematitic ore, too high in silica (quartz) to be commercially viable, was treated by emulsion flotation. A three-component emulsion mixture was used at temperatures ranging from ambient (22° C) to 30° C, 40° C, 49 °C, 59° C and 68° C. The optimal emulsion dosage and composition at ambient temperature were used to determine that dosage for higher-temperature flotation tests. The crushed ore (100%, -8 mesh) was repeatedly washed with tap water, and the filtrate's ionic content was analyzed. The separation efficiency values (a measure of the selective separation and concentration of hematite from gangue minerals) demonstrated temperature dependence, with marked increases at temperatures above ambient. The optimal separation efficiency occurred within the range from 30° C to 60° C. The improved separation efficiencies at temperatures exceeding ambient are explained by quartz depression. This depression is attributed to: • the precipitation of quartz-activating cations, principally calcium and magnesium, at increasing temperature; and • temperature's effect on the collector's solubility and attachment to the aqueous hematite surface.

Jan 1, 1993

By R. G. Lundquist

The idea that fragmentation for mineral processing results from some tradeoff between increased drilling and blasting and increased load on the primary crusher is well known. In a previous paper (Lundquist and Konya, 1963) the authors reported on the results of a laboratory scale study which attempted to quantify this tradeoff in energy terms. If we look only at the production of new surface area, blasting is 1700 times as energy efficient as crushing. On an energy cost basis, crushing is 57 times as expensive per unit surface produced as blasting with dynamite and more than 700 times as expensive as blasting with ANFO. The comminution process at an open pit operation starts with the drilling of blast holes and ends after the material has gone through the fine grind circuit. Operators usually break the process into several separate operations and do their cost analysis based on this approach. Often drilling and blasting is considered as one system and crushing and grinding are considered as one or two separate and independent systems. Operators will independently optimize each system. The cost for the drilling and blasting system is obvious in operations which use contract drillers to do the drilling and either contract the blasting to a distributor or do the blasting themselves. The cost of rock breaking in this manner is readily available since the contract driller will supply a monthly drilling cost to the operation and either the distributor who is contracting the blasting or the distributor who is supplying the powder to the blasting operation will also supply a monthly billing. In either case, the costs can easily be seen on a monthly or per ton basis. They are not difficult to compute even when drilling and blasting are done entirely in-house.

Jan 1, 1985

By Kostas Fytas

A computer package has been developed which is capable of evaluating alternative production schedules (long and short range) of an open pit mine once the ultimate pit limits have been defined. The model user can choose the best alternative according to cash flow considerations and the particular mining conditions. The package involves a combination of simulation for long range production scheduling and linear programming for short range scheduling. The simulation model based on an iterative technique, maximizes the profits within each long scheduling period (eg. year or sixth month period), and at the same time defers stripping as long as possible. A minimum exposed ore quantity is kept at the beginning of each mining period. The final long range schedule satisfies a set of constraints for each period, mainly ore quality and quantity constraints for ore and waste. An interactive smoothing procedure at the end of each period results in a schedule that is feasible in terms of mining practice. Finally a cash flow analysis model carries out cash flow calculations so that the user can select the best alternative. The linear programming model, based on a certain number of shovel regions, defined interactively by the model user, calculates the optimum production schedule for each short period under consideration, so that a set of constraints is satisfied.

Jan 1, 1986

By I. H. Keith

INTRODUCTION The following papers describe the extraction of nickel in the form of ferronickel from the Dominican laterites. The Falconbridge process was developed initially in the Falconbridge Metallurgical Laboratories and subsequently in several successive stages of pilot plant operation in the Dominican Republic. In the course of this work we came to believe that there is advantage in piloting on site. Mining, metallurgical and geo-political considerations all have major impact and that belief has been borne out by commercial plant experience. Lateritic nickel ores differ substantially, even within the same orebody, in their amenability to extraction methods. The Falconbridge process takes account of the heterogeneous nature of the deposit. Three years of geological field exploration led to ten years of process development after it was realised that the then known metallurgical processes would not give economical extraction from the Dominican ores. In addition to establishing the viability of a novel pyrometallurgical approach, it was necessary to verify design parameters for a very considerable scale-up to prototype commercial operation. The plant was eventually constructed within the original estimates of time and cost. Unique features contributing to the technical and commercial success of the project are described. Additionally, some bold extrapolation based on pilot plant work, eventually proved to be quite conservative. The mine is not a conventional open pit operation, but is perhaps better characterised as an earth moving job. Novel application of mobile equipment led to great flexibility in the mine, where operation of several mining fronts is essential to maintaining uniformity of ore feed to the plant. The practical aspects of almost total acceptance of the oversize run-of-mine material through a high-capacity unit,

Jan 1, 1979

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By D. K. Jorgensen

The Bullfrog and Montgomery-Shoshone deposits, near Beatty, NV, have a combined drill-indicated reserve of 15.8 Mt (17.4 million st) of ore. Average grade is 3.5 g/t (0.103 oz per st) gold and 8.2 g/t (0.24 oz per st) silver. The deposits occur in Miocene volcanic rocks that underwent large-scale movement within a detachment-faulted terrane. The principal host to gold mineralization is a strongly welded rhyolitic tuff that experienced brittle deformation during plate movement. Open space fractures and breccia were filled with quartz, calcite, and adularia accompanied by lesser pyrite, gold, and acanthite. Gold occurs as micrometer-sized particles within and adjacent to the low-angle fault and along associated listric-normal and tear faults. The Bullfrog and Montgomery-Shoshone are volcanic-hosted, detachment fault-related, epithermal quartz calcite stockwork gold deposits. Bullfrog's minable reserve is 13 Mt (14.3 million st) of ore grading 3.8 g/t (0.11 oz per st) of gold. At Montgomery-Shoshone, 2.7 Mt (3 million st) minable tons at 2.5 g/t (0.072 oz per st) are present. Preproduction stripping has begun at the Bullfrog ore body. A 7.7-kt/d (8500-stpd) carbon-in-pulp (CIP) mill is under construction. In 1990, Bond Gold expects to be producing about 6.2 t/a (200,000 oz per year) of gold.

Jan 1, 1990

By Richard Switalski, Thomas Scotese, James Morrison, Randall Essex

OVERVIEW Like many older metropolitan areas across the U.S., the Greater Cleveland area is served by a combination of separate sanitary sewers and combined sanitary-stormwater sewers. In 1966, a Master Plan was implemented by the Northeast Ohio Regional Sewer District (District) to minimize pollutant overflows into adjoining Lake Erie and its tributary rivers and streams, that would occur during wet weather events. One component of the Master Plan was to reduce the load on combined sewers by constructing new conveyances to intercept separate sanitary flows and convey them to upgraded regional waste water treatment plants for priority treatment. As part of a 15-year program to construct 74 km (46 miles) of new interceptors, the West Leg Interceptor (WLI) Project intercepts flows from four decommissioned waste water treatment plants (WWTPs), and conveys those flows to the new Southwest Interceptor (SWI), which conveys the flows to the Southerly Treatment Plant, a tertiary level treatment facility. The WLI Project was built in sections to permit decommissioning of the WWTPs as each segment of the interceptor system was completed and put into service. Flows from the first of the four WWTPs was converted to the WLI in November, 1992; the final connection was achieved in July 1994. The WLI comprises 9.1 km (5.7 miles) of 21 to 29 m (70 to 95 ft) deep mainline interceptor tunnel, four vortex drop structures, approximately 2 km (1.3 miles) of shallow tunneled connector sewer to the mainline, approximately 2.9 km (1.8 miles) of open cut connector sewers, five construction work shafts (not including one work shaft constructed under SWI Contract 6 at the north end of the WLI), and 15 access shafts.

Jan 1, 1995

By D. Boufounos

The large open pit areas of surface mining as well as the huge quantities of residues generated during the digestion of bauxite with sodium hydroxide solution to produce alumina are considered as the most important environmental problems associated with the exploitation of bauxites. Aluminum of Greece, which is the only aluminum refinery in the country, located in Agios Nicolaos, Paralia Distomou, Viotia, produces almost 680.000 tones of bauxite residue annually which is pumped through pipes from the refinery to the sea bed of Antikira gulf. In order to avoid any kind of environmental problems related to this disposal method and to reduce the total volume of bauxite residue disposed of in the environment, Aluminium of Greece investigates several alternatives for bauxite residue utilization. In this framework, it also examines the potential use of bauxite residues as a filler in abandoned mining open pits. Bauxite residues are mainly composed of fine particles of silica, aluminum, iron, calcium and titanium oxides and hydroxides. Furthermore, the material presents low hydraulic conductivity, slightly higher than the limit posed for low permeability layers by the EC landfill directive. Based on these properties the dry disposal method was selected for disposing bauxite residues in mining open pits since it has many advantages such as reduced overall disposal cost, effective use of land and minimum environmental impacts. The results obtained for this method, which is investigated at demonstration scale, are presented in this paper.

Jan 1, 2005

The National Mining Hall of Fame and Museum in Leadville, CO seized the opportunity to show off during its 10th anniversary induction banquet on Sept. 6. "We wanted to make people more aware of the mining hall of fame and museum," said Carl Miller, its executive director. The annual event honors inductees into the Mining Hall of Fame. This year, the inductees included Paul Wheeler Allen, Joseph Rosenblatt, Arthur Fay Taggart, Joseph Toy, Joseph Wharton and John Benjamin Zadra (ME, August, pp. 60-63). Allen, of Pasadena, CA and Rosenblatt, of Salt Lake City, are both living. Only Allen was able to attend. This year's induction banquet was the first held in Leadville, North America's highest incorporated city, at 3,094 m (10,152 ft) above sea level. The banquet gave attendees an opportunity to see the museum in its century-old 6,500-m2 (70,000-sq ft) Victorian schoolhouse. Many of the 350 guests came in 1890s dress to the black-tie affair. The evening included a cocktail reception and an open house along with a catered, prime rib dinner. During the open house, attendees had the opportunity to tour the museum's 12 rooms of exhibits and displays. Among items of interest, it was noted that a framed directory of inductees now enhances the entrance to the hall of fame. The directory is organized by the inductees' names and the location of their plaques, allowing visitors to quickly find hall of fame members. Noted mining historian and author Duane Smith delivered the keynote address at the banquet. After the induction of the six honorees, attendees danced to the big-band era music of the Leadville 17-piece band BandAge. Karl Elers was the master ceremonies for the evening's program. He is a member of the hall of fame's board of directors and is chairman of Battle Mountain Gold Co. Allen was honored by the presence of 26 former colleagues and associates. He told the audience that he originally thought the museum should have been located in Denver. "But I have been proven wrong," he said. For many years, Allen was the operational executive of Cyprus Mines Corp. and a key participant in the company's growth. Allen received a replica of his mining hall of fame plaque from Thomas Falkie, chairman of the hall of fame's board of governors and president of Berwind Natural Resources Co.

Jan 1, 1997

By F. Djahanguiri

The US Bureau of Mines con¬ducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1997

By S. G. Haycocks, M. Karmis, C. Haycocks

Risk assessment is a primary factor in the decision to mine some near surface orebodies, such as limestone, by either surface or underground methods. Identification and quantification of risks demonstrate that environmental concerns are greater for surface operations than underground, and may include such factors as runoff, spoil piles, aesthetics, dust, and large site reclamation. Risk assessment also includes local public feeling towards surface and underground operations while considering the balance between environmental impacts and the economic effects of mining on the local community. A complete understanding of the risks involved permits a comprehensive and accurate comparison between the two mining alternatives.

Jan 1, 1992