Search Documents

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

Jan 1, 1997

By D. B. Gentzler, J. L. Kohler

A method of monitoring production information (raw tonnage and machine state) from each working section has been developed. The method is based on the sensing of electrical parameters in each section load center, and the reporting of this information through the existing mine-wide monitoring system. A decision-theoretic type of pattern classification technique has been used to define the machine states. The basis of the method is presented in this paper, along with a proposed hardware and software implementation scheme. Information issues central to the development and use of the proposed production monitoring system are also discussed.

Jan 1, 1990

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

By Saied S. Navid, Michael A. Piepenburg, Richard F. Escandon, Robert C. Lindsay

INTRODUCTION Phase I of the Los Angeles Metro Rail Project, known as MOS-1 (Minimum Operable Segment-1), is the first phase of the 27 km± (17 mi) subway starter line. MOS-1 is currently under construction and involves approximately 6.4 km (4.4 mi) of subway, five stations, yards and shops routed through the downtown area of Los Angeles. The project will form the initial heavy rail backbone of a more extensive light and heavy rail transit system planned for the greater Los Angeles area in the future. Construction Contract A-171 is one of 4 tunnel contracts within MOS-1 and involves construction of twin tunnels running from the downtown metropolitan area west to MacArthur Park. The heavily populated and developed downtown area, potentially gassy ground conditions, and the possibility of undocumented abandoned oil wells in seismically active southern California made the design and construction of Contract A-171 a uniquely interesting project. This paper summarizes the construction history to date (December, 1988) including design geotechnical considerations, tunnel support design, as-built geologic conditions, shield tunneling performance through soft ground, and ground response. The findings presented herein may aid in the design and construction

Jan 1, 1989

By Howard L. Hartman

To concede that I am the most surprised - not to mention the least likely - recipient of the Daniel C. Jackling Award is a true confession I must share with you. Quite honestly, I've asked myself, "Why me?" The Jackling Award has a well-deserved reputation of being a practitioner's, a doer's, a CEO's award - not kudos for a retired school teacher! While at least five of the previous recipients have taught in universities, to my knowledge I am the first to earn the award for "alleged" academic accomplishments. It is humbling enough to keep me livable for a long time. If you glance over the roster of Jackling Award lecture topics, you will spot another anomaly: The lectures last year and this deal with the subject of education - the only two in the 37-year history of the award. The two complement one another rather well, too, C. Allen Bom of Amax addressing critical needs of public education, while I am going to look at the post-high-school years. But I want to focus on more than engineering education. The training role of industry - the principal consumer of our product-also warrants examination. As I hope to establish, there is something unique about mining engineering - education and practice - that is both strength and weakness. We need to recognize that, if we are to cope with the weaknesses in order to capitalize on the strengths. We look at five premises that relate to the uniqueness of the mining engineer and his or her preparation for a professional career.

Jan 1, 1991

By Mark A. Anderson

INTRODUCTION The accomplishment of a well engineered design, and the realization of efficient plant operation cannot be achieved without weaving a web of safety consciousness from the beginning of the project. When the plant becomes operational, and throughout its life, responsibility safety will rest with the client or operator. Recognition of this understanding does not reduce the importance of the engineering and construction contractor's role, but merely puts the responsibility where it belongs. A project which has had little or no operator input during the early stages of design is almost certain to have serious work place safety, health, and environmental problems in spite of the fact that all MSHA and OSHA design requirements were met and the engineering was performed using accepted practices. DEFINITIONS The author has a personal preference in safety definitions that begins and ends with simplicity. If the safety criteria, program, and rules are confusing or complex, the results will soon become obvious. Confusing and complex are the key elements in the avoidance of responsibility and if punitive is added to the list, a brew exists which breeds accidents, illness, and poor performance. A safely designed and operated plant is one that a worker can journey to each day; leaving that person and his or her family with the above average expectation that the person will return healthy, emotionally intact, and hopefully a little wealthier. If the objective or results of a planned or existing safety program don't fit the definition. then the reader is probably contemplating a very sophisticated

Jan 1, 1986

By Z. Nivolianitou

This article aims at highlighting the importance of technological innovation, namely the potential use of Virtual Reality (VR) technology, as a Sustainable Development Indicator for the minerals industry. Nowadays, VR is regarded as a mature technology for real world representation, and it has been already applied in various domains such as architecture, topography, aeronautics, medicine, and lately in the process industry. Several industrial sectors already use VR tools, as the car industry for improving car ergonomics and design and the aviation industry for both pilot and maintenance crew training. It is well known that the mining industry, as well as the process industry, requires people to work in hazardous environments and situations, often inadequately trained owing to limitations in time and resources, building thus the potential for minor or major accidents.

Jan 1, 2007

By Brian Burdett, Terry I. Mudder, Robert T. Richins, James A. Stevenson, Michael M. Botz, Alan L. Wilder

The first Cyanisorb process was constructed in 1991 at the Golden Cross Mine in Waihi, New Zealand to recover cyanide from CIL tailings. The Golden Cross operation consists of an open-pit and underground gold mine with a conventional crushing, grinding and CIL circuit with Merrill Crowe zinc precipitation for gold recovery. Prior to disposal in the tailings pond, slurry tailings are stripped of cyanide at a pH of approxi­mately 7.5 using the Cyanisorb process. Mill throughput is approximately 2,500 tons per day (TPD), and CIL slurry tailings average 37% solids with a specific gravity of 1.27. CIL tailings WAD cyanide average 150 mg/L. The Cyanisorb process recovers approximately 85% of tailings WAD cyanide, produc­ing a slurry effluent with approximately 20 mg/L WAD cyanide. A second Cyanisorb process was commissioned at the NERCO DeLamar silver mine in southwest Idaho in May, 1992. The ore milling and silver recovery operation consists of crushing, grinding, a CIP circuit and Merrill Crowe zinc precipi­tation for silver recovery. Cyanide recovery is from clarified tailings with WAD cyanide ranging from 3 50 mg/L to 600 mg/L, producing an effluent with less than 30 mg/L to 60 mg/L WAD cyanide. Due to the presence of zinc-cyanide complexes in mill tailings resulting from the Merrill Crowe process, cyanide is stripped at a pH of approximately 5.5.

Jan 1, 1995

By M. Karmis

Surface subsidence has been recognized as an inevitable consequence of underground coal mining for several centuries. The damage resulting from this phenomenon has been witnessed in rural as well as in urban areas and ranges from simple land settlement to severe structural damage to buildings. Subsidence prevention is not feasible, at least under the existing technological and economic constraints of underground coal mining. Using a rational method of subsidence prediction, it has been demonstrated in many coalfields that subsidence control can be successfully practiced in order to reduce and accommodate subsidence within environmentally acceptable levels. This paper presents the development and testing of a subsidence model, based on the zone area method. This technique is a refined development of the influence functions and it is capable of investigating a mining plan of any shape, thus facilitating both longwall and room-and-pillar mining systems. More specifically, this study can be divided into two major efforts: (a) The development of the zone area model. This formulation was designed to accommodate the analysis of an optimum number of zones, over the area of interest, both accurately and efficiently. (b) The testing of the computer techniques with appropriate field measurements. In order to accomplish this, published as well as unpublished information was collected and analyzed according to a regionalized scheme. This procedure minimized differences in subsidence characteristics between the various coalfields and allowed a regional validation of the predictive capabilities of the model.

Jan 1, 1982

By Dr. Richard F. Coon, James D. Mavis

Risks and abatements associated with preliminary reconnaissance, plugging and filling, and maintenance of perched mine water pool are examined. This case history showed that the initial appeal of portal plugging was replaced by concern over potential environmental hazards when details of implementation were investigated.

Jan 1, 1992

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By P. M. Lin, P. Tsang, S. S. Peng

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands (AML). The method considers column grouting at specific locations, including the destressed and stress concentration zones, instead of grouting around and beneath damaged structures. The latter method is currently commonly used for AML subsidence abatement. The finite element method (FEM) can be used to calculate stress distribution in the strata before and after grouting. A grouting pattern is generated that includes the location and number of grouting holes. Stress concentration can be reduced or eliminated. A comparative analysis, including the number of grouting holes, area of grouting influence, stress level and potential of subsidence reoccurrence, is also presented.

Jan 1, 1993

By J. P. Nairn, C. M. McCulloch

More and more underground mining is being conducted using the long wall method. Likewise, many new surface mines use area or mountaintop removal methods. These methods can have a significant impact on surface and ground water resources. The overall study of the effects on surface and ground water from mining is referred to as the probable hydrologic consequences (PHC) determination of mining and reclamation. Collection and interpretation of information concerning ground water and surface water quality and quantity, as well as detailed geologic analysis, is required to adequately define the impacts of mining. This paper discusses the present day requirements and methodology of preparing a PHC for a large mining operation in the eastern coalfields.

Jan 1, 1997

By Y. K. Yen, J. D. Miller, C. L. Lin

A PC image-based, on-line coarse particle size analysis system is being developed for the control of crushing and grinding circuits. Initial results had indicated that the system is accurate when tested with irregularly shaped particles which are stationary and do not overlap with each other. Now the system has been successfully tested in the dynamic mode with a moving belt conveyor. On-line size analysis for actual plant operations is discussed and includes: (1) the video system with respect to lighting and data acquisition requirements for a rapidly moving belt and, (2) image sampling, specifically the number of observations needed for accurate sampling and the total time required to perform the calculations for a representative data set.

Jan 1, 1993

By Carmine Nappi

This article examines some important trends in East-West trade in non-fuel mineral products, in particular the recent decline in Eastern bloc exports of such products. It relates this decline to an improvement in Soviet terms of trade; a deterioration of geological and locational conditions in Soviet mineral production; an increased integration of the CMEA-countries based on a regional pooling of resources; and a surge in demand for mineral commodities in Eastern countries coupled with a slowdown in Western economic growth. Finally, it evaluates to what extent these determinants may evolve in a different direction during the eighties and thus foster East-West mineral trade. Eastern1 bloc trade in mineral products is a subject of perennial interest in the West. When exports increase, there is much talk of the dangers of dependence on the East for critical fuels and materials. When imports increase, talk turns to the danger of Soviet dependence on Western supplies. A common fear is that the USSR may not only seek to meet its own resource needs but also deny the access of Western countries to these resources. This paper, like three other recent additions to the lite5ature on Soviet foreign trade of commodities2, tries to put matters in clearer and cooler perspective. The first section evaluates the structure of East-West mineral trade and tries to identify some important trends of recent years. The second section relies on supply and demand factors, as well on the Comecon connection (the intra-Council for Mutual Economic Assistance mineral cooperation) to explain why there has been a reversal in the mineral trade trend since the end of the seventies. The last section evaluates the factors which could stimulate East-West mineral trade in the future.

Jan 1, 1986

By R. W. Smith, K. A. Altman

The use of activated alumina for the removal of selenium from heap leach detoxification solutions was studied at a laboratory scale. Three different aluminas were studied, one unmodified and two chemically modified to function better in a basic pH range. The best performer, Discovery Chemicals DD-6, readily accumulated selenium oxyanions. Furthermore, it could be stripped of selenium and several metals by a mild caustic solution (pH 11.5 – 12.0) and regenerated for further use. Tests using - 600 µm, + 300 µm (28 x 48 mesh) material indicated that 96 % could be removed from solution and using – 1.18mm, + 600 µm (14 x 28 mesh) material 91 % could be removed. However, soluble silica can accumulate on the activated alumina and subsequently interfere with its regeneration and should be removed from the detox solution prior to use of the adsorbent.

Jan 1, 2003

By Sanja Zlatanic, Michael P. Della Posta

New York State’s Metropolitan Transportation Authority (MTA) has undertaken the largest transportation project in New York City. The East Side Access Project (ESA) will introduce MTA’s Long Island Rail Road (LIRR) service to the East Side of Manhattan, to a new terminal located beneath the existing, landmark Grand Central Terminal(GCT). Construction of the Manhattan Segment of the project will affect overlying operating facilities of two other MTA entities, Metro-North Railroad (MNR) and New York City Transit (NYCT) and major Midtown Manhattan buildings. The paper describes the evolution of the GCT concept at Manhattan from a shallow alternative proposed by a Major Investment Study (MIS), that would require extensive underpinning of multi-story buildings and have considerable impact on MNR and NYCT operations, to a deep alternative with lesser risk and potential for disruption.

Jan 1, 2001

By Steve Lloyd, Mary Anne Antonioli, Byron Darnton

Pegasus Gold Corporations' Montana Tunnels mine began oper­ation in March 1987. The process plant at startup consisted of a bulk flotation circuit followed by leaching of the reground bulk concentrate. The leach residue then advanced to selective Pb/Zn flotation. This original circuit had its share of problems, and the leach circuit was abandoned after six months. The bulk flotation circuit was modified to selective Pb/Zn flotation at this same time. Gravity concentration was researched early on, prior to selecting bulk flotation with leach as the flowsheet of choice. Flotation was deemed to be more practical than gravity due to the lower capital and operating costs. No further work was done concerning gravity concentration until 1990 when it was decid­ed to investigate ways to diminish the occurrence of free gold reporting to the flotation tailings.

Jan 1, 1996

By J. H. Fewings

The rapidly escalating capital costs for new projects, or extension of existing projects, has placed greater emphasis on maximum use of existing resources. Thus, when increased grinding capacity was required to achieve metal production from lead-zinc ores a number of alternate approaches were studied. The most cost effective way of achieving the required 5% increase in grinding circuit capacity was to install upgraded instrumentation and computer control of grinding - Fewings, Wickham and Wiseman (1). Once the computer installation cost had been borne by the financial returns from that project, other projects involving computer control were economically viable on an Incremental cost basis. These Included centralised control of tailings thickening and return circuit water distribution, centralised control of the crushing plant and use of the computer as a data processor for an on-stream analysis system for flotation slurries.

Jan 1, 1979

By Robert L. Cascio

The mining industry uses a large amount of electric power. Their equipment is subject to extreme environmental conditions and mechanical shock. A significant number of electrical accidents are a result of improperly grounded electrical equipment. Federal regulations require the safety ground bed resistance to be measured once a year or after modifications. Most commercially available instruments used to measure the ground bed resistance require the ground conductor to be disconnected and the power system disconnected for safety reasons. The "fall of potential1' method requires auxiliary ground rods and approximately two hours to complete the test. Although a new instrument was initially thought to measure the ground bed resistance immediately without isolating the ground bed, field tests have shown this method is not accurate. In some cases, a continuous measurement of the ground resistance is desired. A monitor has been developed and is presently being evaluated at several mines. These installations will be discussed.

Jan 1, 1992