Search Documents

By N. S. Tanious

This paper summarizes results from an investigation into possibly the largest coal pillar failure in the USA. The newly opened coal mine worked an 3.35 m (11 ft) seam under overburden depth that ranged from 91 to 671m (300 to 2200 ft) . The mine main entries, and the enclosed pillars, experienced a massive slow squeeze. The squeeze could not be controlled and the mains were lost. A new set of mains were driven. Entry convergence (closure) measurements were carried out behind the advancing face to monitor stability. Pillar stresses were also measured under four different depths of overburden: 229.433, 472.579 m (750,1420,1550, and 1900 ft). The strength of pillars in the new mains was calculated from the loads that triggered the failure in the old mains, using three pillar strength formulas. The stress measurements showed that the new pillars supported more load than their predicted strength, indicating that current strength formulas are inadequate under deep conditions.

Jan 1, 1992

By Ethan B. Eilertsen

Titanium solves corrosion, maintenance and environmental problems in many reactor and autoclave applications. Titanium clad construction permits autoclave designers a great deal of flexibility combined with significant cost reduction. Titanium alloys can be selectively applied in specific regions of the autoclave to accommodate local environmental conditions. Resistance to general corrosion, crevice corrosion, abrasion, and ignition conditions can be accomplished selectively and economically. Explosion clad pressure vessel fabrication and performance have been proven through three decades of experience.

Jan 1, 1997

By L. Neuman

Reclamation and permit applications for mines tend to be very detailed and complicated documents. Depending on its complexity, the application may have to be reviewed in detail for water quality, water quantity, wetland and upland habitat, wildlife issues, waste disposal, historical and archeological significance, other environmental factors, and financial surety sufficiency. To reduce review time and cut costs to the applicant, this paper identifies the most common mistakes that can lead to delays in the application process.

Jan 1, 2004

A number of factors affecting the properties of cemented aggregate fill (CAF), particularly its strength development have been studied through a series of laboratory investigations carried out at the Western Australian School of Mines in the Western Australia in recent years. The outcomes of these investigations indicate that apart from cement dosage, aggregate particle size distribution, aggregate quality, additional fine materials, water salinity, admixture dosage and sample scaling all contribute significantly to the development of cemented aggregate fill strength.

Jan 1, 2001

By R. L. Pozzo, A. S. Malicsi, I. Iwasaki

The electrochemical nature of mineral-grinding media interaction in the wet grinding of one and two sulfide mineral ores was investigated with regard to the flotation behaviors of the minerals. Two iron sulfides (pyrite and pyrrhorite) and mild steel were used to represent the sulfide minerals and the grinding media, respectively. Galvanic currents in two- and three-electrode combinations under abrasive and non abrasive conditions were correlated with the floatabilities of these minerals under corresponding conditions.

Jan 1, 1991

By George D. Coumoulos

The following aspects of diasporic bauxite are discussed: The importance of world reserves of diasporic bauxites; the geological, chemical and mineralogical characteristics of the Greek diasporic bauxite; the uniformity of bauxite deliveries; the significance of the absence of organics; the excellent settling properties of the red mud; the production of sandy alumina from diasporic bauxites; the advantages of applying tube digestion systems in processing diasporic bauxites; the conditions for introducing diasporic bauxite in the existing European refineries.

Jan 1, 1984

By Ian Graham

In 2013 the Government of New Zealand launched a number of ‘National Science Challenges’ (NSC) to address major issues facing the nation, and raise public consciousness about science and its role in promoting evidence-based decision making. One of the 10 proposed NSCs focuses on New Zealand’s extensive Exclusive Economic Zone (EEZ) and Extended Continental Shelf (ECS)1, with an objective to enhance utilisation of marine resources within environmental and biological constraints, and the desired outcome of:

Sep 1, 2014

By A. Shakoor, A. M. Hirt

The compressive strength of coal, and its variation within and between seams, was determined for four Pennsylvania coal seams (Pittsburgh, Sewickley, Upper Kittanning and Lower Kittanning). Large coal blocks were obtained from 12 coal mines (three mines per seam) and cut into 50-mm (2-in.) cubes using a low-speed saw. The cubes were tested for compressive strength, with the results used to compute actual pillar strength. Using the tributary area approach, the pillar stress was determined. The pillar stress and strength data were used to calculate the factor of safety against pillar crushing for each mine. The cube strength was also correlated with various physical and chemical coal properties (density, percent absorption, percent ash, percent sulfur and percent carbon) to see if any strong relationships exist. The coal's mean compressive strength varies from 9.1 MPa (1326 psi) in the Lower Kittanning seam to 37.8 MPa (5480 psi) in the Pittsburgh seam. Between different seams the pillar strength varies from 29.5 MPa to 48.1 MPa (4282 psi - 6981 psi). Although coal strength appears to be weakly related to carbon content, no relationship was found between compressive strength and other physical or chemical properties. Since the values for the safety factor against pillar crushing generally exceed the recommended value of two, the existing pillars are mostly overdesigned. This implies that an accurate assessment of coal compressive strength could result in the use of smaller pillars and, thus, increased coal production.

Jan 1, 1993

By Ron M. Canon, John M. Begovich

Chromatography, ion exchange, and other techniques based on the interaction of solutes with solid phases offer versatility, high resolution capabilities, and near-universal potential applicability for the separation of valuable constituents in liquid solutions. The expense associated with obtaining reasonable throughput for these separations has been the only, albeit overwhelming, obstacle preventing widescale use of these methods. Attempts to devise continuous (cheaper) systems have previously resulted in moving, or simulated moving, beds of resin with complicated valving and timing sequences. These disadvantages, plus technical problems associated with the disturbing effects of non-plug flow and reduced resolution of moving versus packed beds, severely limit applicability of these systems. Over the past decade a new device has been developed that overcomes many of these problems. It utilizes a slowly (less than one revolution per hour) rotating annular bed of sorbent material with fixed-feed inlet and product withdrawal points. Numerous units of various diameters and lengths have been fabricated and operated, and a parallel effort has developed a satisfactory theoretical treatment of the device. Several simple control systems have been incorporated to thoroughly demonstrate the simplicity of operation, even for multiple products and multiplecarrier flows. This device has been developed using several metal solutions and has demonstrated its power with some of the most difficult, including the zirconium-hafnium, separations. Design equations are available for sizing units based on simple laboratory data and have been tested for units as large as 18 in. in diameter.

Jan 1, 1985

When I reached Warren after the "de luxe" South American expedition I had little idea what was in store for me. From the large check Thayer had handed me just before I left New York I was pretty sure the future would be good, and that before long it would involve Anaconda. Evidently, Mr. Thayer had left it to Dr. Ricketts and John Greenway to work out the details The next morning Greenway asked me to come to his office and told me that he and Dr. Ricketts had discussed the question and that Anaconda would make me an offer I could not refuse. They proposed to pay me almost $1000 a month, more than twice my current salary. They had agreed that I should stay with Calumet and Arizona for the rest of the year to help with Bisbee development and anything I could to assist with the New Cornelia plans and construction Of course I could not turn down such a flattering offer, as I had about reached the limit of advancement with a much smaller company in anything save a high executive job, and it would be a long time before I could be ready to change from exploration and geology to operating. Greenway and I agreed that I would stay with him for the remaining eight months of 1916 without any particular title but helping in any way I thought would be most useful. Bisbee and Ajo Study It turned out to be a busy half year, in addition to many good times with my Bisbee friends. The Uplift Club did not meet as regularly as in earlier years, but Mason Ross, Jim Lewis, Bill Gohring, Roy Mitchell, Hubert d'Autremont, Arthur Notman, and I did have many "bull sessions" and poker games. I saw much more of Greenway than before and made many trips with him to Ajo and later to the new

Jan 1, 1976

By John G. Banker, Arthur L. Forrest

Titanium solves corrosion, maintenance and environmental problems in many reactor and autoclave applications. Titanium clad construction permits autoclave designers a great deal of flexibility combined with significant cost reduction. Titanium alloys can be selectively applied in specific regions of the auto­clave to accommodate local environmental conditions. Resistance to general corrosion, crevice corrosion, abrasion, and ignition conditions can be accomplished selectively and eco­nomically. Explosion clad pressure vessel fabrication and perfor­mance have been proven through three decades of experience.

Jan 1, 1996

By S. P. Lucido, I. Iwasaki

The potential of controlling heavy metal ions in effluents from discontinued mining operations and waste rock piles has been investigated. A fresh water green alga, Cyanidium caldarium, was found to have the potential to remove Cut' from solutions while exhibiting high tolerance to acid conditions which are commonly encountered in copper-nickel mine drainage. The process has the potential for application as a low maintenance metal decontamination system. The growth requirements and copper removal characteristics of this microorganism are described.

Jan 1, 1991

By David J. Kruse

Accurate field measurements are essential when validating a conveyor design. They are fundamental in determining a conveyor's behavior, its long-term maintenance requirements, and the life expectancy/ condition of the installed equipment. Field measurements are also invaluable in forensic engineering, particularly when vital equipment has failed This paper will discuss a wide variety of data acquisition equipment, field measurement techniques and accuracies achieved State-of-the-art, custom designed monitoring equipment, as well as, ''08-the-shely instruments and sensors, will be discussed.

Jan 1, 2004

By Donald R. East

In the planning and design of mill tailing disposal facilities, the chemical and physical nature of the fine­grained material to be disposed of has to be fully understood in order to create an efficient and safe long­term storage facility. Disposal of tailing has become the single most important source of environmental impact for mining projects and the development of many promising ore bodies has been delayed or even stopped due to problems of facility siting and design under pressure of increasingly stringent regulatory require­ments.

Jan 1, 1992

By W. W. Roberts

Key elements to the successful excavation and support of the Forest Glen Station and Tunnels for the Washington Area Metropolitan Transit Authority are discussed. Excavations encompassed a twin-vault station; 2339.3 m (7675 feet) of conventional drill and shoot tunnel; and 810.8 m (2660 feet) of mixed faced tunnel. The use of dewatering, boom type continuous miner and shotcrete in the mixed faced tunnel, along with hydraulic drills, bolts, and shotcrete in the rock tunnels and station proved to be effective methods.

Jan 1, 1983

By I. A. Molodkina, A. V. Kurkov, V. V. Shatalov

New compound classes previously unknown in flotation practice of non-sulphide ore beneficiation have been developed. The presented study results consider amine salts of alkyl sulphate and alkyl benzene sulphonic acid used as primary collectors, N-methyl amides of alkyl phosphoric acids - as auxiliary modifying collectors and pentaerythritole ethers of tall oil - as flotation accelerators. These reagents synthesized from accessible raw material are almost ready for commercial production. Efficiency of the new reagents for various non-sulphide ores has been demonstrated in a series of flotation tests.

Jan 1, 1995

By H. J. Zhang, W. Wui

With the adoption of market-oriented economic policies, Chinese non-ferrous metals industry has gained remarkable progress. The continuously increasing domestic demand for non-ferrous metals, however, calls for more import of raw materials in short supply, such as copper concentrate and bauxite. As an alternative for balancing the shortage and assurance of more stable mineral supply, direct investment in oversea mining project has come to the agenda. This paper discusses the computer-assisted method used for evaluation and comparison of potential mining projects.

Jan 1, 1996

By J. Franko, M. S. Klima

Wet-drum magnetic separators are used extensively for upgrading iron ore and for magnetite recovery in dense-medium separation circuits. In this study, the performance of a continuous, laboratory wet-drum magnetic separator was evaluated both with and without the application of ultrasonic energy when processing dense medium slurries. Test variables included magnetic-to-nonmagnetic ratio, solids concentration and nonmagnetic material. The results indicate that, under certain conditions, the purity of the magnetic material increased after ultrasonic treatment. Key words: Ultrasonics, Wet-drum magnetic separation, Iron ore

Jan 1, 2003

By R. Brough, T. K. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, and ship-lap, to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1990

By Park. D. W., Y. M. Jiang, L. A. Morley, W. Keeton

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floors and thinly-laminated immediate roofs. This investigation concerns a mine that was experiencing ground-control problems with weak floor conditions. Several roof falls occurred locally, and as much as 0.6 m (2 ft) of floor heaves have been experienced. The paper presents the results of comprehensive analyses conducted on floor heave, roof sagging, pillar- penetration and floor bearing capacity using instrumentation and numerical modeling.

Jan 1, 1993