Search Documents

By Stephen J. Crittenden

Deep gas and oil production has been substantially increased over prolonged periods through the use of sintered bauxite propping agents. Since its inception in 1976, over 170,000,000 pounds of high strength ceramic proppants have been employed. Recent field evaluations and economic analysis demonstrate the superiority of sintered bauxite proppant over quartz sand. This paper describes the development, application, field results, and product evolution of sintered bauxite.

Jan 1, 1983

By Donald W. Trepp

Colony Development Operation is a joint venture currently consisting of four active members; The Oil Shale Corporation (TOSCO); Ashland Oil Inc.; Shell Oil Company and Atlantic Richfield Company, operator of the project. The initial efforts on the Colony project began in the spring of 1965. Pilot mining and semi-works engineering programs continued, in phases, to completion in the fall of 1972 when commercialization of oil shale was deemed realistic. Since that time, Colony efforts have been directed toward evaluation of the data collected during the semi-works operation and in designing a commercial operation. In October of 1974, Colony announced: "because of economic and national energy policy uncertainties it was suspending plans to start construction of a commercial oil shale plant on private lands in northwestern Colorado, scheduled for spring of 1975."

Jan 1, 1975

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By Bill Cain, David F. Tsztoo, R. John Caulfield, D. Scott Kieffer

In 1994, the East Bay Municipal Utility District (EBMUD) commenced a system-wide Seismic Improvement Program to protect their facilities from catastrophic damage. A primary focus of this program has been on retrofitting the 75-year old Claremont Tunnel, which crosses the active Hayward Fault zone. A large earthquake on the Hayward Fault could generate enough right-lateral fault slip to effectively sever this important lifeline. The retrofit project involves construction of a new bypass tunnel through the Hayward Fault zone, together with systematic contact grouting and localized structural repair of the existing concrete liner. Several innovative design measures have been incorporated into the seismic retrofit design, including an oversized tunnel cross section, backfill concrete side drifts, seismic isolation of an internal structural pipe, and shear fuses in the final lining.

Jan 1, 2005

By G. Bonifazi

In the present work the possibility to utilize the morphometrical and morphological characteristics of an articulate solids system in a slurry flow to monitorate and to control a continuous process is considered. This goal has been reached by mean of an optical system able to acquire, to handle and to process the pictorial information derived by a suitable hardware architecture designed to realize the best lighting, focusing and sampling conditions for the examined flow stream domain. The procedure has been tested using different flow stream slurries coming from different sections of a beneficiation plant. A suitable strategy and a consequent software architecture has been set up in order to assure to the system the necessary speed and the stability to achieve correct on-line measurements and control.

Jan 1, 1994

By Marline J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in non-metallic mining with limited financial risk IF properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgements are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources.

Jan 1, 1977

By Nasri Munfah, Steffen Matthei, Vojtech Gall

"Conventional tunneling as defined by ITA WG19 is also known as the New Austrian Tunneling Method (NATM) or Sequential Excavation Method (SEM) was transformed in the US to deal with challenging tunneling conditions as an alternative to the more traditional tunneling methods. It is being used more often in urban areas, under difficult ground and ground water conditions, and with limited cover. Often the tunnel is of a large and non-uniform cross section in soft soils or weak rocks. The intent of using this tunneling method is to minimize impact on traffic and utilities and reduce disruption of everyday life of people and businesses. To meet these challenges, the industry developed technical approaches and implementation techniques and established sophisticated contractual relationships and collaboration in the field among various parties for successful implementation. This paper examines the development of conventional tunneling (NATM/SEM) in the US to deal with these challenges using recent examples such as Russia Wharf in Boston, Northern Boulevard Crossing, in New York, and Chinatown Station in San Francisco. INTRODUCTION / HISTORY Conventional tunneling or NATM/SEM is a concept that is based on the understanding of the behavior of the ground as it reacts to the creation of an underground opening. In its classic form the SEM/NATM attempts to mobilize the self-supporting capability of the ground to an optimum thus achieving economy in ground support. Initially formulated for application in rock tunneling in the early 1960’s, NATM has found application in soft ground in urban tunneling in the late 60’s and has since then enjoyed a broad, international utilization in both rural and urban settings. In the US the NATM/SEM tunneling method has been used successfully to address challenging tunneling conditions in urban areas. A large number of tunnels have been built around the world using a construction approach which was loosely termed NATM. During the years of discussions and the application of NATM a variety of terms have been used for the same construction approach. These terms were primarily aimed at describing the construction approach rather than the region of its reported origin."

Jan 1, 2016

By B. C. Haydon

Manganese silver ores are well known to be refractory towards cyanidation. Various processes have been suggested for improving the amenability of these ores. A sulfurous acid pre-leach is one such process. This paper traces the development and implementation of the sulfurous acid pre-leach process for the retreatment of manganese silver tailings at Tonopah, Nevada. An account of the test work program is presented, followed by a description of the operating plant and specimen metallurgical performance. The paper also summarizes the history of the Tonopah tailings, their mineralogy and makes reference to previous application of the sulfurous acid pre-leach process.

Jan 1, 1984

Caterpillar said it will produce a Cat line of ac electric drive mining trucks. The world’s largest manufacturer of mining and construction equipment said the addition of an AC electric drive truck line will provide its customers with products to fit key applications. “We are very proud of the strong leadership position that Caterpillar has attained with its mechanical drive trucks, and we will continue to invest in strengthening that position,” said Chris Curfman, president of Caterpillar’s Global Mining Division and Caterpillar Inc. vice president. “We also recognize that there are unique applications that would make the addition of ac electric drive an important and attractive complement to our current truck line.” This is the largest investment Caterpillar has made in mining trucks in its history.

Jan 1, 2006

By R. C. Bunge

The success of a mineral separation is commonly assessed from the separation curve, a graph of the recoveries achieved versus the corresponding separator settings. Two values characterize the curve, first the "splitpoint" which is the separator setting that produces a recovery of 50%, and second a measure for the separation sharpness. The splitpoint represents the "mean" while the measure for the separation sharpness represents the "scatter". In modelling the performance of crossflow separations the mean particle behavior is calculated from the force equilibrium that determines the particle trajectory which leads to a deterministic model. The scatter is then represented by a stochastic model. This presentation discusses the modeling of a crossflow separation and some implications with separation theory. The model is shown to successfully predict the performance of a magnetogravimetric separator.

Jan 1, 1992

By Ruben Piqueras, Juan Luis Magro, Jorge Vázquez, Santiago Martínez, Xavier Manjarín

The Parallel Thimble Shoal Tunnel project involves the construction of a bored tunnel under Thimble Shoal Channel in Chesapeake Bay (VA), between two artificial islands and parallel to the existing tube tunnel, built in the sixties. It will be the first transportation tunnel constructed in the Mid-Atlantic region using a Tunnel Boring Machine (TBM), a 44-foot-diameter Earth Pressure Balance (EPB) named "Chessie," manufactured by Herrenknecht, and which was assembled at the CBBT's southernmost island, with extremely limited room, live adjacent traffic, and difficult access. "Chessie" was successfully launched in February 2023 and this paper describes this complex and challenging process.

Jun 23, 2024

By B. Boutilier, R. Mendoza

"First Majestic Silver Corp. (FMS) is a silver mining company founded in 2002 that operates exclusively in Mexico. It has six producing silver mines, one of which is the La Encantada silver mine (La Encantada) located in the state Coahuila. La Encantada is located near the southern United States border and 708 km (440 miles) north of the city Torreon.La Encantada is located in the Sierra Madre Oriental and is a high-temperature carbonate replacement deposit. Mineralization in La Encantada occurs in many different forms such as veins, chimneys, breccia pipes and reefs (mantos). Mineralization is mainly oxides of iron, zinc, lead and manganese, with high concentrations of sulfides at depth relating to two main intrusive events: the Milagros Intrusive and the La Prieta Skarn.Mining began in La Encantada during the 1950s with small vertical shafts, drifts and raises. It focuses on the high-grade silver zones using traditional hoists and extraction methods, before branching into two main separate mining camps: El Plomo and Penoles camp. Penoles, the previous owner, focused mainly on large ore bodies using post pillar cut-and-fill mining method to extract the higher-grade material. Due to the type of ground, irregularity of pillars, and rock conditions, large amounts of high-grade pillars had to be left in situ to ensure the stability of the excavations. The mined-out areas would then be filled with lower-grade material to assist in the stability of the secondary level. These room-and-pillar development entries were 2.5 m x 2.5 m (8.2 ft x 8.2 ft) and spaced every 10 m (32 ft), leaving a vertical pillar of 7.5 m (25 ft). First Majestic acquired La Encantada in 2006. After the acquisition of the mine, the company began the conversion of the surveying reference system from a local grid (Maria Isabel Shaft as 0,0) to the Nav27 coordinate system, and subsequently converted to the WGS84 coordinate system in 2015. Due to the extensive history of the mine, different areas were surveyed with different systems, causing significant challenges when designing the principal extraction levels, pillar heights and ramp locations. To overcome this difficulty, the entire mine was resurveyed and the old workings transposed to the new coordinate system, except for some inaccessible areas due to poor ground conditions or ground collapses. To further ensure pillar height and the safety of the mine workers, probe holes were drilled during the development process."

Sep 1, 2019

By Martin C. Kuhn

The use of tritium in manufacturing and its subsequent loss to the local environment in Tucson, Arizona resulted in a great debate relative to the physiological effects of low level radiation. This paper reviews some of the facts of the release and attempts to quantify the degree of hazard encountered by the local community. Some of the difficulties in assessing the true degree of absorbed dose and the assumptions necessary for calculation purposes are presented.

Jan 1, 1981

By L. G. Austin, R. C. Klimpel

Batch breakage kinetic tests were performed in a mill of 0.3 m diameter for a range of mill conditions. Accurate simulation required the measurement and use of factors which accelerated the specific rates of breakage of the top sizes as finer material accumulated in the slurry. These factors depended on the size distribution expressed relative to the top size, not the absolute size, suggesting that they are due to a packing effect not a rheological effect. The data simulated correctly a series of steady-state continuous tests in a mill of the same diameter providing values were corrected to the hold-up, ball load, slurry density, and size distribution measured in the continuous mill tests.

Jan 1, 1990

By Erik S. Bernard

"INTRODUCTION Conventional steel bar reinforcement is used in many tunnel linings to provide high flexural and tensile load resistance. These Reinforced Concrete (RC) tunnel linings may suffer flexural cracking during service or, in the case of precast concrete segments, during production, handling, or installation. Cracks can lead to corrosion of steel reinforcement, so limits are placed on maximum acceptable crack widths to reduce the likelihood of corrosion during the intended design life (AFTES, 2013; MC2010, 2012). However, the relatively light level of reinforcement used in many applications can result in quite wide in-service crack widths, so either additional steel bar reinforcement is required to limit maximum crack widths, or fibers can be included to control crack widths. Numerous investigations have been undertaken into the efficacy of including steel fibers to reduce crack widths in conventionally reinforced members (Stang and Aarre, 1992; Abrishami and Mitchell, 1997; Bischoff, 2003; Dupont and Vandevalle, 2003; and Jansson et al, 2010), but steel fibers suffer the problem that they are at least as sensitive to corrosion at cracks as steel bars and therefore have similarly tight limits placed on acceptable crack widths (AFTES, 2013). An alternative means of maintaining narrow crack limits in RC members has therefore been sought. The current investigation was instigated following an observation that theories promoted as an explanation for the ability of steel fibers to reduce crack widths in reinforced concrete flexural members (Deluce et al, 2014) do not depend on the material composition of the fibers used but instead depend primarily on the tensile stress generated by the fibers across cracks. Since it is known that macro-synthetic fibers are capable of equaling the post-crack tensile capacity of steel fibers, it has been hypothesized that macro-synthetic fibers are also capable of reducing crack widths in reinforced concrete flexural members but with the added advantage that macro-synthetic fibers are completely immune to the effects of corrosion. Use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete flexural members subject to aggressive environmental exposure is more rational than use of steel fibers because steel fibers are very sensitive to the corrosive effects of environmental exposure at cracks. The current investigation was therefore undertaken to explore the potential use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete members subject to flexure. Barchip BC54 fibers were selected as they are one of the most widely used and competitive high performance macro-synthetic fibers currently available."

Jan 1, 2016

By I. Moreno-Ventas, G. Ríos, J. C. Fernández-Caliani, M. Bacedoni

"This paper delves into the constraints on the nature, origin and thermal evolution of the accretions formed in the uptake shaft of the flash smelting furnace operated by Atlantic Copper in Huelva, Spain, outlining recommended practices for preventing accretion buildup. The accretions were investigated using quantitative electron probe microanalysis, X-ray diffraction and digital imaging techniques, and the experimental data on mineral composition, crystal chemistry and textural relationships were interpreted in terms of thermodynamic phase equilibrium in the SiO2-Fe-O-S system. The results suggest that two distinct types of accretions were formed by the fractional crystallization of two coexisting immiscible melts, under changing conditions of oxygen partial pressure (pO2). The type I accretion of magnetite + delafossite ± cuprite ± tridymite ± metallic copper crystallized from a fractionating copper-rich melt at pO2 above about 10-5 atm, while the type II accretion of magnetite + fayalite + metallic copper + chalcocite derived from a melt with lower copper concentration when pO2 levels dropped below that critical level. Phase compositions and textures were consistent with a cooling history of both compositionally contrasting liquids from about 1,250 °C, the liquidus temperature of magnetite, to eutectic or near-eutectic temperatures of around 1,100 °C. The maintenance of appropriate temperatures — above the liquidus temperature of magnetite — and oxygen partial pressure levels may be critical for the prevention of accretion buildup. IntroductionCopper flash smelting with oxygen-enriched air, an autothermal process developed half a century ago by Outotec (Espoo, Finland), formerly Outokumpu, currently accounts for about 50 percent of the world’s primary sulfide-based copper (Schlesinger et al., 2011). The partial reaction of copper sulfide concentrates produces two separate molten streams, copper-iron-sulfide matte and iron oxide-rich slag, and releases sulfur dioxide (SO2) gas. The matte is sent to converters to remove the remaining iron and sulfur, leaving blister copper with grade of about 99.5 percent copper (Cu), which is cast into anodes for electrolytic refining.The SO2-rich gas generated by the oxidation of sulfide feed particles contains a significant proportion of dust that is entrained in the process off-gas. The gas from smelting is transferred into a waste heat recovery boiler, where it is cleared of dust and cooled before it is converted into sulfuric acid. If the process is not operated properly, the dust-bearing gas may form accretions between the uptake shaft of the flash smelting furnace and the waste heat recovery boiler, causing severe problems in the gas handling system (Swinbourne, Simak and Yazawa, 2002; Miettinen, 2008; Stefanova et al., 2012). Removing the dust accretions usually requires a greal deal of time, effort and resources. Understanding the buildup of accretion may help in reducing the problems and optimizing the process"

Jan 1, 2017

By B. J. Scheiner

The Federal Bureau of Mines has developed a chlorine-oxygen leaching technique for the recovery of metal values from lead-zinc sulfide concentrates. Lead, zinc, copper, cadmium, and silver extractions are in the 95- to 99.9-percent range. During leaching, the zinc, copper, cadmium, and silver are solubilized as metal chlorides, and lead is converted to insoluble lead sulfate. The iron contained in the concentrate is converted to insoluble iron oxide, and a majority of the sulfide is converted to elemental sulfur Minor metals such as copper, cadmium, and silver are recovered by precipitation with zinc dust. Zinc is then recovered from the purified zinc chloride solution by evaporation to dryness; the lead is recovered from the leach residue by brine leaching and crystallization to produce lead chloride. Recovery of zinc and lead metals by fused-salt electrolysis of the chlorides is being studied separately.

Jan 1, 1975

By F. Wolf, R. Ellmies

"Fluorspar is one of the most important industrial minerals. It has a wide range of applications, for example it is used in the steel and aluminum industry, and is also the raw material to produce hydrofluoric acid, Teflon or Gore-Tex. There are only a few major fluorspar mines worldwide, with China being the most important fluorspar producer (U.S. Geological Survey National Minerals Information Center, 2017). At Okorusu, Namibia, fluorspar has been mined with conventional open pit mining methods from 1955 until 2014 from a large scale metasomatic fluorspar deposit with seven identified orebodies. There are about 7 million tons of measured resources left with an average grade of 27.5 % CaF2. This paper is based at an MSc thesis at Technical University Freiberg and describes the design of an underground mine for the A and D orebodies with an annual production rate of 100,000 t acid-grade fluorspar product. By comparing different mining methods and adapting variants of access to the underground orebodies the paper will emphasize on the selection of a suitable mining technology, with a special focus on the economic considerations to decide about the most profitable operation. INTRODUCTION Mining holds an important part in the economy of Namibia. In 2016 11.1 % of the GDP was made through mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists an underground mining operation. The global annual production of fluorspar is approximately 6 to 7 million t (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu produced on average about 50.000 t annually in recent years (U.S. Geological Survey National Minerals In-formation Center, 2015). Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an open pit mine with four individual pits (A-D) since 1980. In 2014 the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village. The intent is to develop a concept for the further underground development of the mine. There are still about 7 million t of measured resources left in the deposit, with an average grade of 27.5 % CaF2. This study focusses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged."

Jan 1, 2018

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006