Search Documents

By J. N. Carras, N. W. Bainbridge

In order to further the understanding of spontaneous heating of longwall goafs a numerical model was developed, based on conservation principles applied to the transport of heat, water vapour and oxygen across the god Advective air flow into the goaf is caused by the differential air pressures across the god The air velocity field within the goaf area was computed using Darcy's law. The boundary and initial conditions concern air pressure, temperature and relative humidity. The oxidation rates and heat generation rates of the goaf materials required for the simulation were obtained from laboratory measurements. The main outputs of the model are temperature, oxygen and water contour maps, the rate of air leakage into the go4 velocity field and pressure distribution across the god. The model while still in its development stage, is able to simulate a heterogenous goafs constructed from different materials with different thermal and mass flow properties. Validation of the model by comparing its output with measurements from within goafs is required before the model can be used with confidence in a predictive sense.

Jan 1, 1995

By E. M. Frizzell

Development of mobile crusher systems for surface mining, allowing extension of continuous conveyor haulage systems into the pit, is traced from its introduction to the present. Variations in configurations are reviewed, and the compelling reasons for using mobile crusher systems are explored.

Jan 1, 1983

By Rohan Fernando, David P. Snyder, John F. Burr, Susan M. Moore

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done.As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal.Technology gaps targeted by the MINER ActThe MINER Act addressed several technology challenges:• Problems with donning and switching between self-contained, self-rescuers (SCSRs).• Poor visibility in smoke.• No wayfinding assistance for escape from the mine.• Limited breathable air supply.• Inability to locate trapped miners.• Inability to communicate with trapped miners.• Failure of mine seals."

Dec 1, 2016

By K. Luxbacher, A. Haghighat, B. Lattimer

Mine face ignition due to high levels of methane is one of the most common fire incidents in underground coal mines. In continuous miner headings, depending on the magnitude of the ignition or resulting fire, auxiliary ventilation controls may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to an exhausting ventilation curtain in a continuous miner heading, and the impact on ventilation to the face. The computational fluid dynamics software Fire Dynamics Simulator (FDS) Version 6.0 was used to predict the conditions that develop due to a 200-kW fire in the face following a methane ignition with different levels of assumed ventilation curtain damage. Smoke layer depth, temperature and mass flow inby the last open crosscut were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed curtain. As more of the ventilation curtain was damaged, smoke depth and temperature outby the fire increased. With the full removal of the curtain, the smoke accumulated from the last open crosscut to the face, with the ventilation completely bypassing the continuous miner region.

Jan 1, 2016

By G. R. Giuliani

Hanna Mining Company's Groveland Mine is located in the Upper Peninsula of Michigan. The low grade iron ore deposit consists of a mixture of magnetite and hematite with chert, jasper, quartz and various iron silicates (1). The ore is beneficiated by magnetic separation and anionic flotation of the iron minerals with chemical depression of the silica. The magnetic concentrate makes up about 75% of the concentrate. The concentrate is pelletized at the rate of 2.0 million LTPY of pellet production. The concentrator facilities were started up in 1959 and the concentrate was marketed as sinter feed until 1963 when the concentrator was expanded and the pelletizing plant was added. The pellet plant now consists of regrinding, elutriation, filtering, balling and induration. The pellet machine is a straight grate which employs updraft drying and cooling and downdraft drying, preheat and firing. It is necessary to regrind the concentrate before pelletizing. The con-centrate is 60% passing 325 mesh, with a surface area of ±lOOO cm2/Gm, and must be ground to about 83% passing 325 mesh, 1600 cm2/Gm blaine surface area, for pelletizing. The energy for regrind has been reduced from 12.5 KW per LT to 8.80 KW ate of 2.0 million per LT. This was the result of changes made in the concentrator where originally a coarse spiral concentrate, instead of the magnetic concentrate which is screened on fine screens to reduce the coarse fraction and prevent overgrinding before flotation, was produced. Also in 1968 an additional concentrating line was added to the concentrator which employs more grinding power than the other three lines. The demand for a high iron grade and lower silica pellet resulted in the investigation of different schemes of upgrading the reground concentrate which had more iron values liberated during grinding for surface area. The reagentized material presented many problems, mainly in selectivity trying to flot the iron and with high reagent consumption having to dereagentize the concentrate for amine silica flotation, in the various flotation systems tried. Tests were then conducted with elutriation (2) which proved satisfactory by removing the lower specific gravity, fine gangue material from the heavier material with the

Jan 1, 1977

By Z. Jin, D. DePaoli, P. Zhang

"Phosphogypsum is a byproduct created during the production of industrial wet-process phosphoric acid. This study focused on recovering rare earth elements (REEs) from a Florida phosphogypsum sample and investigated the effects of removing detrimental impurities such as phosphorus pentoxide (P2O5 ), uranium (U) and fluorine (F) during the leaching process. Experimental results indicated that REE leaching efficiency increased rapidly, reached a maximum and then began to decrease with sulfuric acid concentrations ranging from 0 to 10 percent and temperatures ranging from 20 to 70 °C. At a sulfuric acid concentration of 5 percent and leaching temperature of 50 °C, REE leaching efficiency obtained a maximum value of approximately 43 percent. Increasing the leaching time or liquid/solid ratio increased the leaching efficiency. The leaching efficiencies of P2O5, U and F consistently increased with sulfuric acid concentration, temperature, leaching time and liquid/solid ratio within the testing ranges. A fine-grain gypsum concentrate, sized smaller than 40 µm, was separated from leached phosphogypsum through elutriation, in which the P2O5, U and F content levels were reduced by 99, 70 and 83 percent, respectively, from their content levels in fresh phosphogypsum. IntroductionPhosphogypsum is a byproduct generated during the industrial wet process of phosphoric acid production, in which sulfuric acid is used to digest phosphate rock. Gypsum (CaSO4·2H2O), the main component of phosphogypsum, usually accounts for 65 to 95 percent of phosphogypsum by weight.There are small quantities of impurities in phosphogypsum, such as phosphates (H3PO4, Ca(H2PO4)2·H2O, CaHPO4·2H2O and Ca3(PO4)2), fluorides (NaF, Na2SiF6, Na3AlF6, Na3FeF6 and CaF), sulfates, trace metals and radioactive elements (Rutherford, Dudas and Arocena, 1996). Global phosphogypsum generation is estimated at 200 Mt/a (Parreira, Kobayashi and Silvestre, 2003; Yang et al., 2009), but only about 15 percent is recycled as building materials, agricultural fertilizers or soil stabilization amendments (Tayibi Choura and Lopez, 2009)."

Jan 1, 2017

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By Kevin Saeler, Patrick Willaman

Utilizing automation is one way to improve competitiveness. Roof and rib bolting in underground coal mines has not changed significantly for more than 40 years. Most roof bolting is still a largely manual process involving high levels of staff carrying out repetitive work. Roof bolting statistically has one of the highest levels of underground accidents, including finger, hand, and arm injuries. Operators are exposed to falling objects and becoming entangled in roof bolting apparatus while roughly moving awkward 6-ft drill steels and roof bolts. It is estimated that over 25 million roof bolts are installed annually in the U.S. underground coal market with well over 1,500 operators involved in roof bolting on a day-to-day basis. Recently electrohydraulic roof bolting rigs have been installed to offer partial automation of the drilling cycle and the bolting cycle. The next stage is to provide a storage and loading system to allow full automation of fullcolumn resin roof bolts. This paper reviews the latest electrohydraulic roof bolting equipment and discusses the testing of a fully automated drill rig. Full electronic control allows each step of the roof bolting process to be recorded, providing a digital record of each installation, including hole depth, spin time, gel time, torque, and cycle time. Other benefits include monitoring of water pressure and flow, used to prevent blocked drill steels as well as digital fault finding. A fully automated roof bolting machine greatly improves operator safety and gives high-quality repeatable roof bolting with reduced cycle times.

Jul 1, 2023

By G. Duncan

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above..

Jan 1, 1999

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

Contributions made by mining have played a much more significant role in the development of civilization than is generally conceded by historians or recognized by ordinary citizens. In modern society, mined products pervade all industry and the lives of all civilized people. Early man relied largely on stone and ceramics, and eventually metals, to fashion tools and weapons. Civilization was advanced by discoveries such as abundant supplies of high-quality flint in northern France and southern England and firesetting to break rock. Middle Eastern cultures flourished not only because of agriculture and trade, but also because of mineral-rich deposits nearby. The earliest miners date back perhaps to 300,000 BC; their quest was for nonmetallic minerals (chert, flint, obsidian) suitable for utensils and eventually for weapons. Other rocks and minerals (ceramics, clay, salt, meteoric iron) attracted the miners for jewelry, cosmetics, construction materials, food seasoning, and coinage. At first, their excavations were confined to the surface, either pits or placers. But by about 40,000 BC, mine workings had been extended underground as short adits or shafts, and by 8000 BC as elaborate interconnected openings 300 ft (90 m) in depth. Metallurgical separation of metals from their ores and their subsequent fabrication evolved gradually over the centuries, copper being the first liberated (c. 7000 BC) followed by lead, silver, gold, and iron. Man enhanced both the sophistication of his

Jan 1, 2008

By Stephen W. Denton

Planning a mining operation in Alaska will involve the investigation of many parameters common to mine planning anywhere. However, there are some unique circumstances that must be recognized when one considers development of mining operations in Alaska. This paper will not attempt to provide a blueprint for mine planning in Alaska, but hopefully will provide a better understanding of the truly unique nature of the northern latitudes. Given this understanding, the mine planner can better assess the potential hurdles along the road to a successful mining operation. The regulatory trend towards uniform standards for mining throughout the United States exemplifies the necessity for Alaska to prove its unique position in the natural resources picture. The factors which make Alaska truly different from the "Lower 48" can be summarized by four points 1) Remoteness and Size 2) Seasonable Extremes 3) Geologic Immaturity 4) Vegetation and Wildlife

Jan 1, 1984

By G. K. Hoffman

Humate, defined as weathered coal or mud-stone rich in humic acid (HA) and fulvic acid (FA) have been mined, primarily as soil amendments or drilling mud additives, in New Mexico for 15-20 years. The New Mexico humate resource is estimated to be 11 Gt, including weathered coal and organic mudstone. The HA and FA content determines the end-use, therefore a simple and consistent method of measuring organic-acid content was developed. The New Mexico Bureau of Mines and Mineral Resources method is based on repeated alkali leaching and acid precipitation. Precipitates of humate are ashed, with mass balance of solids maintained, to correct for material added during alkali-acid treatment. Analyses of upper coal member, Cleary Coal Member (Menefee Formation) and Fruitland Formation samples from the southeast San Juan Basin show ashing to be important in accurate analysis of FA content. Ash in the total FA fraction averages 70% compared to 2% in HA. The FA in weathered coal and organic mudstone are similar, although HA is significantly higher in the former. As weathering progresses, the FA content of weathered coal increases faster than in organic mudstone because of the greater total organic material in coal.

Jan 1, 1994

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector is one of the leading sectors where work accidents are most intense because of the constant change of work environment and heavy working conditions. The losses and the halt of production after the accident negatively affect productivity and production efficiency. It has been found that there are very few studies on the use of Data Envelopment Analysis (DEA), which is one of the nonparametric efficiency analysis methods, in the evaluation of mining sector occupational accidents. According to parametric activity measurement methods, it has been tried to show that the DEA can also offer the opportunity to interpret work accidents by taking advantage of its advantages. Due to the application of open-pit mining methods along with underground working techniques which increase the risk factors with respect to accidents at work that occurred between 2012 and 2018 of Western Lignite Corporation (WLC) were tried to be analyzed in the present work. As a result of the analytical work using Data Envelopment Analysis (DEA) for the years 2014, 2015, 2016, 2017, and 2018, inefficiency has been determined in both underground and surface operations. According to the results obtained, it was determined that WLC could not produce enough production in both the underground and surface coal mining operation, despite the accidents that occurred, while it had the opportunity to produce more. In addition, it was found that the increase in accidents occurred more than the increase in the amount of production during the years studied.

Jul 4, 2021

By JIACHENG XIE, XUEWEN WANG, QINGBAO BAO, ZEWEN YAN

The general application of memory cutting technology to shearers is improving the intelligence of the working face, but it has its limitations. It is only suitable for conditions where the environment of coal seam is changing slowly. It compensates for the cutting height by changing the fuselage attitude, and frequently adjusts the height to control the learning cutting trajectory, but due to the problems of shearer control and height adjustment accuracy, it cannot adapt to and compensate for the change of cutting height in a timely manner, resulting in poor cutting accuracy. This study puts forward a virtual memory cutting method based on prediction of the shape of the armored face conveyor (AFC). The integrated key technologies include generation of virtual teaching cutting curve, height adjustment strategy of front and rear drums, cutting

By L. Frost

The establishment of a retreat system of longwall mining in this submarine coal field has been under study for many years and, although in special cases there have been limited local applications of this method of mining, there has been no attempt until quite recently to establish a uniform system of longwall retreating' in this area (see Figure 1) Where retreat walls were established, it was strictly as a result of physical, rather than economic conditions. In some of the operations- of the Corporation, where the coal was liable to spontaneous combustion- or the area subject to bumps as in No. 2 Mine of the Cumberland Railway and Coal Company in Springhills the recovery of the coal on a retreat system was more or less a necessity.

Jan 1, 1964

By P. R. Pereira

This paper presents a comparison between the simulations of a semi-empirical model and a theoretical model for the prediction of radial stress in rock. The results of the simulations were compared to the results of a field test. The comparison of the radial stress predictions shows that in the semi-empirical model use of the plane wave approximation as the basis for the prediction of the radial stress provides a much better result than the theoretical model. The theoretical model includes the correct elastic wave geometry and theory but fails twice, firstly by considering the charge as a point (unit) energy source therefore; and secondly by using a Delta function with a very sharp rise and decay time to simulate, with no distinction between non-linear and linear zones, the attenuation of the energy per unit volume at the shock wave front as the wave moves away from the borehole. The results of the semi-empirical model were within the same order of magnitude as the results from the field test whereas only one result from the theoretical model came close to the result of the field test. However, even this closer result for the theoretical should be taken with caution as there was no measurement in the field test made at this distance from the borehole. Finally, because of its potential portability, convenience, and cost-effectiveness the theoretical model can be a most valuable tool for mining and civil construction operators in the early design of blasting rounds and of the mining operation itself.

Jan 1, 1993

By T. W. White

One of the objectives of today's mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

By T. Kretschmer, F. Villwock

Conveyor systems are an essential part of many material movements in all conceivable areas of application. They are used to transport goods in raw materials extraction, agriculture, and even articles for daily use. In the process, not only distances of several kilometers but also differences in altitude of several hundred meters are bridged. The layout of the conveyor usually follows the topography at the respective installation site. Particularly in the case of large height differences, safety devices must be provided to prevent uncontrolled movement. Backstops can take over this task in predominantly ascending overland conveyors and are used either as a primary or as a secondary safety system in conjunction with a service brake. They are always used when the system comes to an unplanned standstill, whether due to a power failure, an emergency stop or a defect. When designing backstops, it must be ensured in any case that all conceivable circumstances are taken into account so that failure is ruled out without the product being unnecessarily large in size. Various safety factors are applied, some of which are even prescribed by authorities. One example is the Australian standard on machine safety for bulk material belt conveyors (AS/NZS 4024). This stipulates a redundant acceleration safety device that can absorb at least 150% of the maximum load. ALTRA Industrial Motion with its sister companies Marland and Stieber manufacture backstops for a wide range of applications. With more than 85 years of business activity in freewheeling and backstop applications, they are among the most known and experienced companies and provide a great know-how.

Mar 2, 2022

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975