Search Documents

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By Randy N. Powell

The Pipeline gold ore body was discovered in Lander County, NV in March 1991. Construction of the new mine and mill did not start until early March 1996. The $289-million project was placed on a fast-track development schedule upon completion of permitting and corporate approval. The mine and mill were commissioned 11 months after the start of construction and the project ended up $40 million under budget. Project design and construction management were provided by Placer Dome Project Development Division (PDD). History The Cortez Joint Venture has operated in northeast Lander County since the late 1960s. The business structure is comprised of 60% Placer Dome and 40%Kennecott Exploration. Throughout the years, production has been from several small open-pit deposits— Cortez, Horse Canyon, Gold Acres and now Pipeline.

Jan 1, 1999

By Harry Deitzer

Within the industrial marketplace barium sulfate has an established role as a filler or extender pigment for use in a wide array of applications. The focus of this paper is to outline a number of these applications and in each one characterizes those features of barium sulfate which provide value. Following this is a discussion of the process techniques which have been used to develop value from a selected class of barite ores found in southern Missouri. It is appropriate to define some terms which may help in clarifying some concepts as presented. Use of the term barium sulfate refers broadly to the chemical compound BaSO4 Barite will generally refer to the naturally occurring barium sulfate ores and their properties. Barytes, whether bleached or not, will refer to barite ore made suitable for industrial applications.

Jan 1, 1993

By W. C. Meyer

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering math models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid chemical interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and predictions of the model are presented.

Jan 1, 1982

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By S. L. Ducummon

Inactive underground mines now provide essential habitat for more than half of North America's 44 bat species, including some of the largest remaining populations. Thousands of abandoned mines have already been closed or are slated for safety closures, and many are destroyed during renewed mining in historic districts. The available evidence suggests that millions of bats have already been lost due to these closures. Bats are primary predators of night-flying insects that cost American farmers and foresters billions of dollars annually, therefore, threats to bat survival are cause for serious concern. Fortunately, mine closure methods exist that protect both bats and humans. Bat Conservation International (BCI) and the USDI-Bureau of Land Management founded the North American Bats and Mines Project to provide national leadership and coordination to minimize the loss of mine-roosting bats. This partnership has involved federal and state mine-land and wildlife managers and the mining industry. BCI has trained hundreds of mine-land and wildlife managers nationwide in mine assessment techniques for bats and bat-compatible closure methods, published technical information on bats and mine-land management, presented papers on bats and mines at national mining and wildlife conferences, and collaborated with numerous federal, state, and private partners to protect some of the most important mine-roosting bat populations. Our new mining industry initiative, Mining for Habitat, is designed to develop bat habitat conservation and enhancement plans for active mining operations. It includes the creation of cost-effective artificial underground bat roosts using surplus mining materials such as old mine-truck tires and culverts buried beneath waste rock.

Jan 1, 1997

By Y. J. Wang

Along with the inexpensive availability of computing hardware, a proliferation of powerful personal computers is being realized throughout the mining industry. People from every arena within the industry are designing, developing, and/or applying mining specific software, which is increasing at a rapid rate. In this section applications (or potential applications) that are being made in the analysis and design of mine systems are discussed, including the design of compressed air networks, the simulation of hoisting operations, analysis of longwall face maintenance, and a summary of computer and software applications for analysis and design of coal operations. In "Computer Aided Design of Mine Compressed Air Networks" the authors describe software, called CompAir, and the underlying theoretical and mathematical foundations of it that can be used to make accurate, cost-effective designs of compressed air systems for mines. It includes algorithms for network analysis and the optimization of pipe diameters. The techniques embodied in the software replace traditional rule-of-thumb approximations which have been used in the past and avoid the operating problems that often result from using average, steady-state parameter values, estimated for ideal operating conditions. CompAir, coded in Turbo Pascal for personal computer use, bases calculations on compressible fluid theory, which gives more accurate results than incompressible fluid theory whenever high flow rates or long line distances are involved. The net- work and pipe diameter analysis is formulated as a nonlinear programming problem. The solution technique requires a trial and error approach that iteratively applies the unconstrained optimal pipe diameter algorithm to successive solutions of the constrained network problem until the diameters become "fixed." The authors conclude by recommending the use of a mine-wide monitoring system to improve cost control and provide a better understanding of flow regimes in compressed air networks.

Jan 1, 1989

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By M. Cai

Transformation of the measured borehole deformations induced by stress relief relies on the traditional assumption that the rock is continuous and homogeneous. Systematic and quantitative tests were carried out to check the performance of devices commonly used for measuring borehole deformations within different types of discontinuous rock conditions. Test results provide a reliable basis for considering the influence of discontinuities on in situ stress measurement and for choosing the best measuring device for a given rock type and condition.

Jan 1, 1998

By D. G. Purdy

Planning, as defined in Webster's New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicated the potential for scrap formation, validated through lab experiments with varying coke rate, basicity, and holding time. The investigation discovered that smelting this combination could yield a metal product comprising 59% Fe, 24.93% Cr, 7.56% Mn, 0.62% Ni, and 0.93% Si. The optimum basicity was found to be 0.6 with 80% recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall CO2 emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of USD 330 per ton.

Jan 10, 2024

By S. E. Chetlin

In the mid-1970?s, the market value of tangible assets of S&P 500 companies far outstripped the value of intangible assets, including intellectual property (e.g., 83% tangible assets v. 17% intangible assets).1 By 2005, the picture was quite different. By that time and continuing to 2010, S&P 500 companies? market value of intangibles was about 80%, with tangible assets accounting for only 16% of market value.2 This swing highlights the importance in today?s world of understanding intellectual property rights and varying strategies and options for protecting them. This paper discusses intellectual property rights particularly patents and trade secrets, specifically: 1) types of intellectual property; 2) choosing the mode of intellectual property protection; 3) obtaining patent protection; and 4) using patents as a sword versus a shield.

Jan 1, 2012

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By M. T. Ityokumbul

The use of yield index, the product of the yield and gangue rejection, for the optimization of separation processes is presented. The characteristics of the yield index are contrasted with separation efficiency calculations and applied to laboratory froth flotation and washability data. Data from continuous froth flotation tests conducted to "optimize" froth flotation using process optimization software were also evaluated with the yield index procedure.

Jan 1, 1997

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By J. A. Botín

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require of more complex risk evaluation models, that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, production rates, among many other). In this context, Real Option Valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed, which successfully quantifies the risk associated to dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mining Project.

Feb 27, 2013

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, violations are often the most frequent form associated with accidents. These occur when an individual, or individuals, deliberately contravenes established and known safety rules. They have been associated with up to 90% of accidents and incidents in some industries and yet rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives which cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of attitudes to determine the underlying motives behind violations if they are to determine effective strategies for promoting safe behaviour. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, however, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 1998

By K. Peri

The leaching behavior of gold in ammonical solutions with iodine as an oxidant has been investigated using cyclic voltammogram and Tafel polarization. The majority of experiments was carried out at 75°C and the results were compared with the equilibrium consideration on the iodine-ammonia system. The distribution of nine iodide containing species at various pH values in the absence and presence of ammonia was considered at three different temperatures. It was found that by introduction of ammonia into the system, the concentration of iodide (r), iodine (12) and triiodide (13') is increased substantially which in turn helps the rate of dissolution of gold. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical controlled mechanism.

Jan 1, 1999

By D. S. Flett

Abstract. The commercial importance of hydroxyoximes as extractants for copper has given impetus to basic studies on the chemistry of metal extraction by these compounds. The discovery of accelerator compounds which produce catalytic effects on hydroxyoxime extraction rates has led to mechanistic studies of these rate processes. While these studies have highlighted the importance of interfacial chemical reactions in the extraction process, it is not yet possible to unambiguously describe the mechanisms of metal extraction in these systems or the associated catalytic effects. This paper reviews progress in understanding the mechanism of metal extraction by hydroxyoximes.

Jan 1, 1979

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016