Search Documents

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By Susan P. Taite, Alain R. Charest, Peter D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in the southwestern Chihuahua state of Mexico (Fig. 1). A Francisco Gold geologist discovered the prospect in1995. El Sauzal was encountered as a result of an extensive grassroots exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas silver camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiaryage. The mineralization appears tobe structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system, including kaolinite, illite, alunite, dickite and pyrophyllite.

Jan 1, 2005

By Werner Burger

After its first introduction in 2013, Variable Density TBMs have increased their application significantly in mechanized closed mode tunneling. Throughout a variety of successfully completed and ongoing projects since then, Variable Density TBM technology has demonstrated its advantages in a wide range of applications. This paper will present the developments and lessons learned from these projects as well as the future potential of Variable Density TBMs.

Jun 13, 2021

By D. Earley

High metal prices and new world trade standards and accounting for environmental liability in financial disclosures are creating markets for metals commodities that are produced using ?green technologies?. A promising "green" gold leaching system uses a polysulfide based lixiviant which is non-toxic and non-polluting. Laboratory testing has demonstrated selective gold extraction rates comparable to those of cyanide. The polysulfide lixiviant is a dilute aqueous solution which can be inexpensively produced from readily available chemical reagents and even mining wastes. The reagent system is self-buffering and maintains the optimal chemical environment for leaching. Treatment of residual leach solutions is not necessary because the lixiviant itself is not toxic, and breaks down as the system equilibrates. Simple closed system boiling is used to recover gold from process solutions. The polysulfide lixiviant can then be readily renewed and recycled back into the system, forming a closed loop system that conserves reagents and energy which minimizes operating costs. Economic projections have shown that the system can be used profitably for standard ore types and grades.

Jan 1, 2009

By Richard J. Robbins

This paper is presented with particular reference to the findings of the OECD Advisory Conference on tunneling held last July in Washington D. C. A great deal has been said about the Conference in the past few months, but it may be appropriate to review briefly the background and objectives of the Conference to better understand how the mining community can relate its underground excavation problems to the results of the Conference. OBJECTIVES OF THE OECD CONFERENCE The world demand for tunneling (the term tunneling is used here loosely to include almost all forms of underground excavation) is expected to grow at an in- creasing rate. During the decade of the ?70's, the demand is expected to at least double by comparison with the previous decade. Much of this increase in demand will be due to the rapid growth of urbanization around the world. As urban populations grow larger and denser, the conservation of surface land and the quality of the environment become more important. This aspect of the increasing demand poses a difficult challenge to those who must plan and implement urban development.

Jan 1, 1970

By E. R. Spencer

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

Jan 1, 2008

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By Anthony R. Przybylek, John M. Visnesky

INTRODUCTION Thermal dryers have been utilized for reducing moisture of bituminous coal since the late 1930's. Since that time, numerous changes in the coal industry have motivated advances in thermal drying technology. The purpose of this paper is to discuss the changes that occurred to dryer design and focus on current practices of fine coal drying. The major topics discussed in this paper are: - Early Thermal Dryer Design and Evolution - Current Drying System Design and Associated Components - Current Economics of Fine Coal Thermal Drying - Future Markets and Design Considerations EARLY THERMAL DRYER DESIGN AND EVOLUTION Background The practice of drying fine coal with heated air has been performed for more than one half century. Throughout that period, both Metallurgical and Steam coal producers have used this method for reducing the surf ace moisture content of their fine plant products. During the late 1930's and early 19401s, vibrating bed and flash dryers were used to per- form the drying duties. Closed water circuits and vacuum filtration had not yet been integrated into process circuitry and centrifugal dryers were in their early stages of development. During that same period, changes in mining practices were reshaping the distribution of coal to our processing facilities. Plants originally designed for the purpose of processing coarser fractions of coal were being burdened with additional quantities of fine coal. Those plants, unable to recover fine coal, would reject these solids to plant bleed. The higher incidences of stream pollution that resulted from these events prompted clean stream legislation and the need for new, more efficient fine coal recovery circuits. The coal processing industry responded to these needs by integrating closed water circuits and filtration into circuits. The fine coal filter cakes recovered exhibited poor handling characteristics by themselves and often required further dewatering to improve their characteristics. Flash dryers at that time were being used to dry the coarser products. For those facilities operating flash dryers, the solution to this new problem appeared to be simple. The filter cake was combined with the coarser (-1/4") coal and then introduced to the flash drying column for drying. The filter cakes, however, presented significant problems for the flash drying systems. Heavy lumps of filter cake could not be dispersed and conveyed by the rising hot air and as a result would settle out in the bottom of the column. This material, known as "drop-out", would then accumulate and require further handling. The solution to this problem was not an easy one. Sophisticated mixing equipment was employed to condition the feed to the dryers. As attempts to minimize drop-out with this approach failed, the only recourse was to collect the material with conveying systems and recycle it back to the plant or dispose of it. The additional costs of handling this material reduced the attractiveness of the flash systems and opened the door for the development of a new, more cost effective coal drying system. Due to the nature of the problems experienced by the flash systems, fluid bed systems were considered. Fluid bed dryers were being used in other industries at that time but had no operating history in the coal industry. Dorr-Oliver transferred technology from other industries and built the first fluid bed drying system for fine coal.

Jan 1, 1988

By M. Javier

"The impact of mine closure is perceived through a veil of compliance to human laws and regulations rather than the laws and equilibrium of nature. This perception motivates present research. Understanding the causes and effects of mine closure defines levels of responsibility. This understanding evolves from mine closure's legacy. Mine closure is characterized in perpetuity by three aspects: Future liabilities; level of technologies for extraction and, usage of mineral resources. These aspects must be updated to a rationally appropriate level. This paper will address the following questions: Will the minerals remaining in the process of mine closure ever be recovered? Will the mine closure inhibit the availability of minerals for the next generation? How many mines are designed to perform a successful mine closure? Do we close the mines or do we close nature? Is it responsible to continue mine closures as we do them today? Is mine closure a complement of mine operations or a contradiction of mining? Do we need to perform mine closures, yet? This paper reviews mine closure practices and principles with the level of responsibility to nature and for the next generation.PREFACE The planet has irreversible issues to deal with regarding the depletion of mineral resources and contamination occurring from human activities. The population increased exponentially to more than seven billion, this high population with its lifestyles, demands a higher supply of minerals. In spite of these conditions, mining is a vital industry to keep ""civilization"" in society. This is evidenced by what we see around us, in that everything ""made"" in society is directly or indirectly due to mining. Hence, mining cannot be avoided or ignored. Society misunderstands the importance of mining in relation to other activities. At this time, mining is fragmented and economically oriented to supply cheap minerals to a market with peculiar characteristics regarding products that could be designed for recycling and stimulate nature’s equilibrium. These issues add important “variable factors” to the equation, when they are considered as parameters for the next generation. It also raises many questions regarding principles and attitudes about morals and ethics exercised in all anthropogenic activities. The industry's practices have many flourishing paradigms which are subject to a variety of criticisms and observations. Some of these observations will be described in this paper. It is important to clarify in advance a ""normal disclaimer"" about the ""apparent contradiction"" that could take place in the writer's comprehension when we abruptly ""jump to conclusions"". We must remember that we are profiling the future in an arena that demands a better understanding of solutions to problems created by actual mining."

Jan 1, 2015

By Harry E. Holzschuh

The two Agrico Chemical Company self unloading Phosphate Rock barges put into service in 1976 operate at over their design carrying capacity. Each barge now carries 26,000 short ton instead of the planned 25,000 short ton at 32 foot of draft. They are in service between Agrico's Tampa, Florida Terminal and the Donaldsonville, Louisiana Fertilizer Complex, moving a total of 2,500,000 short tons each year. This was the first use of the Parascrew design for a marine application. The barges, with their 3,000 STPH unloading and matching loading rate is the vital link in this total transportation and handling system. Rock is moved from the Pierce, Florida Mines through the Tampa Big Bend Terminal, across the Gulf of Mexico, and up the Mississippi to the Agrico Faustina Phosphoric Acid Plant 30 miles below Bacon Rouge, Louisiana. The trip from the terminal to the plant is 600 miles and the turnaround time is just about six days. Seven years operating experience has proved that the system works. Fittingly, the two barges are named the "Faustina" and the "Pierce". They have a beam of 85-feet and are 495 feet long. folded depth is 43 feet, with a ballasted light draft of 19 feet and a typical loaded draft of 32 feet. There are four separated holds with the machinery room located forward of 101 hold. Each hold is 51 feet wide at the coamings with an 18 foot straight section on the side, and a 24 foot long, 600 slope sheet for a 23 foot clear reclaim width at the bottom. The Parascrew in each of the holds is 37 feet long between the bearings and is supported on a 14 inch diameter hollow shaft. The screw pitch varies and the diameter of the flights step up from l'-9" diameter to 2'-6" diameter on the discharge end. By sloping the centerline, a minimum four inch bottom clearance is maintained across the hold. Some bending of the tube does take place.

Jan 1, 1983

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By V. K. Srivastava, T. Gupta, T. Ghosh

"In recent years, the demand for rare earth elements (REEs) has grown due to increasing demand and global supply shortage. The supply deficit of these critical elements has encouraged the search for new sources, with coal and coal byproducts as possibilities. Coals from certain parts of the world can be rich in REEs and can approach a total concentration of 1,000 ppm. Two Alaskan coal samples, from Healy and Wishbone Hill, were investigated for the effects of density and particle size on REE concentrations for three selected size fractions, and flotation tests were conducted on finer fractions. Additionally, bottom ash and fly ash samples from a power plant were examined for their REE concentrations. The results show that the upgrade potential for REEs on an ash basis from a whole-coal basis ranges from 2:1 for the Wishbone Hill samples to 4:1 for the Healy coal samples. Flotations of the finer fractions of the two coal samples, conducted under similar conditions, revealed higher concentrations of REEs in the tailings. Both coal samples had comparatively higher contents of light-group rare earth elements (LREEs) than heavy-group rare earth elements (HREEs). REE content trends for the power-plant products on an ash basis indicate that fly ash has slightly higher concentrations of both LREEs and HREEs than bottom ash. IntroductionRare earth elements (REEs), also known as rare earth metals, and their compounds are vital components in industrial, automotive, petrochemical, defense and medical applications. Dysprosium in combination with other elements is used in laser materials and nuclear control applications. Neodymium is present in magnets that are used in the manufacture of wind turbines and hybrid cars. Europium, terbium and yttrium are used in devices that have visual displays such as computer screens and laptops (Haxel, Hedrick and Greta, 2002; Bunzli, 2013). REEs pose fewer environmental problems of disposal and recycling than their conventional heavy metal counterparts (Haxel, Hedrick and Greta, 2002). They are key materials for radar systems, avionics, modern national defense and satellites (Cammarata and Sieradzki, 1994; Hedrick, 2010; Martin, 2010; Szumigala and Werdon, 2011; Cordier, 2011; Bunzli, 2013). REEs are often classified into light-group rare earth elements (LREEs) and heavy-group rare earth elements (HREEs). This classification is primarily based on the electronic configuration in the outermost shell. LREEs, ranging from lanthanum to gadolinium, have a single or no spinning electron in the outermost 4f shell while HREEs, ranging from terbium to lutetium, have paired electrons in the 4f shell. This difference in electronic configuration is responsible for the differences in physical and chemical properties of REEs."

Jan 1, 2017

By Pierre Mousset-Jones

A questionnaire was sent out to three classes of mines to determine the extent of the heat problem in U.S. and Foreign underground mines. The following list shows the replies received from this questionnaire, however not all the known hot mines in the US replied. A complete listing of the results can be seen in Appendix I. 1) US coal mines - 37 replies 2) US non coal mines - 23 replies 3) Foreign non coal mines - 36 replies. At the present time there are approximately eleven non coal and one coal mine in the US experiencing heat problems which require special efforts to maintain an acceptable working place climate. However since the survey was completed some of them have been placed on standby. The Mine Safety & Health Administration (MSHA) does not have any specific regulations relating to heat stress. Informally the American Conference of Governmental Industrial Hygienists guidelines are followed which use wet bulb globe temperature (WBGT) with values ranging from 26.7°C to 31.1°C for a moderate workload, and different rest regimes. An MSHA report (Misaqi 1976) recommended that conditions should not exceed 26.1°C WBGT for men and 24.4°C WBGT for women. However, quite recently the organizations involved with planning two of the proposed nuclear waste repositories in the United States, have opted for the criteria of an air cooling power of 300 w/m2, and a WBGT of 27'C respectively.

Jan 1, 1986

By Sandip K. Mukherjee

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper reviews developments in water spray dust control technology and recommends guidelines for water spray systems to control dust in under- ground coal and non-coal mining operations. These guidelines suggest type, number, location and orientation of nozzles, desirable operating water pressure, and associated filtration system.

Jan 1, 1983

By Richard L. Sanford

This paper summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory is funded by the U.S. Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 1, 1978

By Thomas J. Feeley

The US Department of Energy (DOE) is supporting the engineering development of three advanced physical coal cleaning technologies: selective agglomeration, advanced flotation and advanced cycloning. Each is capable of significantly reducing the pyritic-sulfur content of US coals. The objective is to provide the coal and electric-utility industries with a cost-effective option for addressing the SO, emission reductions required by the 1990 Clean Air Act Amendments (CAA). A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants (HAS). The proposed National Energy Strategy (NEE) and the 1990 CAA lay a foundation for a more efficient and environmentally sustainable energy future (1991). The need to use energy resources in an environmentally sound manner presents critical challenges and opportunities for coal preparation during the next decade, particularly regarding the control of SOS and HAY emissions. The principal challenge is the development of cost-effective coal preparation approaches for sulfur and HAY precursor removal.

Jan 1, 1993

By V. Anthony Cammarota

MINERALS INFORMATION PROGRAM Mineral data collection by the Federal Government actually began in 1882 with an appropriation by Congress to the U.S. Geological Survey (USGS). Although the Bureau of Mines was instituted in 1910, it was not until 1924 that the collection, interpretation, and dissemination of worldwide information on production, consumption, and availability of minerals became the responsibility of the Bureau. The objective of the Bureau's minerals information program is to maintain and provide reliable, timely, and comprehensive data for analysis of national minerals problems. This program is implemented by a staff of specialists who cover about 100 mineral commodities and the mineral industries of 168 countries. Data are also provided on the minerals industry on the State and county level. The specialists analyze information to identify trends and problems, forecast future U.S. and world supply and demand for the nonfuel minerals, and relate trends and developments to their impact on the domestic minerals industry. Data Sources and Publications The primary sources of data concerning the domestic minerals industry are the companies that produce, use, and trade in these minerals. Approximately 60,000 survey forms are sent to industry, on a monthly, quarterly, semiannual, or annual basis, to obtain the data. Domestic trade data are provided by the Bureau of the Census, U.S. Department of Commerce. Information on mineral developments abroad is developed by Bureau specialists from mineral reports supplied by U.S. embassies worldwide, from primary source documents, from a review of the technical mining literature, and from onsite mine and plant visits in foreign countries. The information is disseminated through a number of Bureau publications: "Mineral Industry Surveys" provide aggregated data on a monthly. quarterly, or semiannual basis to give timely information on the most important mineral commodities. "Mineral Commodity Summaries," published each January, provides preliminary annual data on supply and demand and discusses significant events of the previous year. The final data are published later in the "Minerals Yearbook," which is the definitive historical record for mineral statistics. "Mineral Facts and Problems," an encyclopedic work issued every 5 years, covers industry structure, technology, supply-demand analysis. economic factors, reserves, and forecasts of U.S. and world demand for individual commodities. "Mineral Perspectives" and "Mineral Issues" cover important international mineral developments and significant issues of current U.S. policy as they relate to minerals. Discussions and analyses of mineral trends and developments also appear in other Bureau publications, such as "Minerals and Materials" and "Information Circulars." These publications provide the basis for analysis and policy determinations by the Bureau and by virtually every Federal agency concerned with minerals, defense issues, the national economy, and foreign relations. The data are also used by industry in planning capital investments in mines and processing plants, by financial analysts, by U.S. delegations in their work with international commodity groups, and by a host of other minerals related organizations. Data Bases The data bases used by the specialists for preparing publications or in response to a continuous stream of inquiries include both those that contain individual commodity data from respondents, and those that are summary data bases on production, trade, capacity, employment and a number of other minerals-related items, not all of which are derived from data reported to the Bureau of Mines. The data bases maintained on the mainframes are not accessible by non- Bureau users. A 10-year data base of supply- demand data, published each year as an update of tables that appear for each commodity in Mineral Facts and Problems, is available on a floppy

Jan 1, 1987

By Wilbur I. Duvall

INTRODUCTION This chapter outlines some general principles and procedures that a rock mechanics engineer can use to arrive at a logical design for the size, shape, and spacings of underground openings in various types of com¬petent rock formations. Rock formations can be clas¬sified into six major categories which are useful for design purposes, provided the necessary input data are available regarding the geology of the site, the physical properties of the rock, the in-situ stress field in the rock, and the general geometry of the underground openings. The US Bureau of Mines (USBM) developed a rock classification system based upon these concepts and found it to be useful for design purposes (Obert, et al., 1960; Obert and Duvall, 1967). This classification sys¬tem is given in Table 1; however, an extra column has been added to the original classification to indicate the appropriate design techniques for each rock class. In this classification system, two main classes of rock are considered: competent rock and incompetent rock. Competent Rock Competent rock is any rock which, because of its mechanical and geological characteristics, is capable of sustaining underground openings without the aid of any structural support except that provided by unmined rock in the form of pillars and side walls, etc. Roof bolts and small random props which support only local loose rock are not considered structural supports. Competent rock is further subdivided into three ad¬ditional categories-massive, laminated, and jointed¬ which are defined as follows: Massive Rock: Massive rock is a rock formation where the spacing between mechanical defects such as joints, partings, or faults is equal to or greater than the critical dimensions of openings, or where the strength of the bond across these mechanical defects is com¬parable to the rock strength. Laminated Rock: Laminated rock is a rock forma¬tion divided by approximately parallel planes of weak¬ness into lamina whose thicknesses are small compared to critical dimensions of openings and where the bond between the lamina is weak compared to the rock strength. Elastic Rock-This is rock whose physical proper¬ties will permit the use of elastic theory to predict strains and displacements from applied stresses. Inelastic Rock-This is rock whose physical proper¬ties are such that strains and displacements are a strong function of time as well as applied stress. Incompetent Rock Incompetent rock is any rock which, because of its mechanical and geologic characteristics, is not capable of sustaining underground openings without the aid of additional structural support in the form of linings, steel sets, or systems of props. This classification system for rock depends not only on the mechanical and geologic characteristics of the rock but on the size of openings and their depth be¬low the surface. For example, many competent rocks at shallow depths for small stress fields could become inelastic rock at greater depths and larger stress fields, or competent massive rock for small openings could be¬come laminated or jointed rock for larger openings. Thus, to classify rock for design purposes requires a knowledge of the geologic properties of the rock mass, the physical properties of the rock, the general size of the openings to be mined, and the average range of the in-situ stress field to be encountered. To design underground openings and structures in rock, it is necessary to use criteria of failure for rock under various stress conditions, and to use safety factors to allow for differences between laboratory and in-situ strength properties of rock and to account for errors in¬troduced by the various assumptions made in the design process. Criteria of failure based on maximum stresses have been found to give reliable results in practice. Thus, it is assumed that rock will fail in tension when the tensile stress exceeds the tensile strength of the rock as determined by a standard modulus of rupture test on samples of rock core. If the tensile stresses in rock are small, then it is assumed that the rock will fail at a value of compressive stress equal to the compressive strength of the rock as determined by standard uniaxial compres¬sive strength tests on samples of rock core. These fail¬ure criteria, when used with appropriate safety factors, can be expressed as:

Jan 1, 1982

By James P. Bowersox

Modem mineral processing plants handle large amounts of ore and produce large tailing streams. Plant performance can be optimized when the water is quickly recovered with a thickener. The caisson thickener was developed to overcome process and mechanical problems with the conventional traction and center column units. The caisson is a hollow center column that serves as a pump house. The rake arm structure is supported by a hydrostatic bearing which sits on top of the caisson. The caisson thickener with a hydrostatic bearing has operated for many years in several mineral processing applications.

Jan 1, 1981

By Brooke T. Mossman

Asbestos fibers are highly fibrous silicate fibers that are distinguished by having a large aspect (length to diameter) ratio and are crystallized in an asbestiform habit that causes them to separate into very thin fibers or fibrils. These fibers are distinct from nonasbestiform cleavage fragments and may appear as thick, short fibers which break along cleavage planes without the high strength and flexibility of asbestiform fibers. Since cleavage fragments of respirable dimensions have generally proven nonpathogenic in animal studies, little data exists on assessing well-characterized preparations of cleavage fragments in in vitro models. The available studies show that cleavage fragments are less bioreactive and cytotoxic than asbestiform fibers. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestiform; Cleavage; Fibers; Fibrous

Jan 1, 2007