Search Documents

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By Walter M. Chapman

The National Lead Company operates its MacI tyre Development at Tahawus, New York for the production of ilmenite and. magnetite. The heavy ore of titanium and iron is mined from the open pit mine at an average rate of 7,000 tons per day, and the development waste is removed at an average rate of 10,000 tons per day. The mine working benches are spaced, at 35-foot vertical intervals, and 6 ½ inch blast holes are drilled 39-feet deep with 18-foot burden and spacing by down-the-hole drills. Waste is loaded with a 6 yeard shovel and ore with 2 ½ yard shovels into 22-ton rear dump trucks. A good account of the history of MacIntyre drilling and. blasting was presented to this assembly two years ago, by F. R. Jones. (1) Most of the blasting since the start of the mine in 1941 was done with 90% gelatin dynamite until 1955, when relatively insensitive canned blasting agents were adopted.. In 1956, 9-inch blast holes drilled with down-the-hole drills. In 1956, also, the first experimental trials of prilled ammonium nitrate fertilizer and fuel oil (hereafter called fertilizer) was made following the lead of Cleveland-Cliffs operations in the Hibbing district. Since that trial did not, as some local skeptics predicted, make grass grown on the bluff, but resulted in a well-broken shot, further tests were conducted in dry holes. I Observations of those tests indicated that the fertilizer did its share of the work. If anything, it produced better fragmentation than the normal load di in neighboring wet holes.

Jan 1, 1958

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By Daniel H. McClain

A unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT)Center resulted in a video CD-ROM training program for new miners entering the aggregate industry. Cooperation from everyone involved, including the U.S. Mine Safety and Health Administration (MSHA),made this the product against which other training materials in the mining industry will be measured in the 21stcentury. This product’s versatility and wide application make it a tool that is as critical to a mine’s success as any earthmoving machine. The state and federal grant money involved allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2003

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By Paul W. Patton, Christopher Scott Smith

The use of ceramic-in-rubber pulley lagging on bulk material belt conveyors is increasing. Many of the applications have been on pulleys originally installed with rubber lagging. There is a consensus that the fiction characteristics of the ceramic material are significantly better but the factors quoted vary, possibly because the more complex traction mechanism of the dimpled ceramic elements on the belt is not well understood. In this paper we will report and evaluate field data from a number of field installations to provide a study of actual friction characteristics in successful applications for those who desire reliable data for using ceramic-in-rubber lagging in new conveyor designs.

Jan 1, 2004

By Brett Zernich, Michael Krulc, Brett Robinson

This paper provides an account of the efforts undertaken to construct the Northeast Interceptor Sewer (NEIS) project, which is a portion of a much larger program in Los Angeles, California to upgrade the city’s wastewater facilities. The project consisted of a number of elements, including both soft ground and rock slurry wall shafts, drilled shafts, soft ground EPBM mining, rock TBM mining, large diameter pipe placement, and underground structure construction. The need to complete the project under strict schedule constraints, in addition to the challenges of underground construction in congested urban areas, necessitated the work be undertaken with the proper balance of state of the art equipment, and thoughtful planning. The paper will detail the means, methods, and equipment used on the project, as well as discuss several of the unforeseen conditions encountered during construction.

Jan 1, 2005

By Katarína Gáborová, Marcela Achimovičová, María Florencia Márquez‑Zavalía, Jaroslav Briančin, Oľga Šestinová, Pavel Škácha

In this paper, the structure, morphology, chemical composition and leaching of naumannite ( Ag2Se) were studied. Mechanical activation of Ag2Se in a planetary ball mill resulted in increasing its specific surface area. The influence of milling time on the particle size was studied by particle size distribution analysis and scanning electron microscopy. The leaching kinetics of non-activated and mechanically activated samples in 3.5–7.9 mol/L HNO3 solutions were examined. Subsequently, the effect of leaching temperature in the range of 25–50°C on the recovery of silver from mechanically activated naumannite was documented. The maximum yield of silver 94% was achieved after 120 min of leaching in 7.9 mol/L HNO3 at 50°C for the sample mechanically activated for 30 min. Based on calculated activation energy values from the Arrhenius equation, a mixed leaching mechanism consisting of diffusion and surface chemical reaction as the rate-controlling steps of the solidliquid reaction was assessed.

Mar 4, 2023

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

By Charles C. L. Smith

A review and comparison is made of the circuitry utilized for dc crane control systems. Anti-parallel three phase full wave thyristor bridges for dc motor reversing and speed control are compared with a single three phase full wave thyristor bridge for speed control and either contactor or static switching for reversing control to obtain complete four quadrant operation for crane material handling. In recent years the Harnischfeger Corporation has developed a solid state adjustable voltage control system to control the speed and direction of dc motors for crane applications and handling materia1.1 Shunt wound dc motors are utilized and speed is controlled in the motor base speed operating region at constant torque by a thyristor, silicon controlled rectifier (SCR), adjust- able armature voltage supply. The three phase thyristor bridge is the power controlling element of the dc adjustable voltage control. ELECTROTORQUE is the Harnischfeger Corporation registered trade name for this type of drive system. By controlling the gating signals or firing pulses to the thyristor bridge SCR's the dc output voltage can be varied over a wide range. This range is limited only by the magnitude of the ac applied voltage. To obtain operation of the motor in both directions two thristor bridges are connected in an anti-parallel arrangement. A typical schematic for two anti-parallel connected three phase SCR bridges is shown in Figure 1.

Jan 1, 1973

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By Dean Treweek, Anthony Harding

"Creating stable, safe, constructible and cost effective support to openings in segmental linings is often an important component of successful delivery of a tunnel project. The many constraints on successful implementation include operational, spatial, geotechnical, structural, and constructability. Failure to address these adequately can lead to significant impacts on cost, schedule, and safety. With reference to past project experiences, this paper provides a guide to the most commonly deployed solutions and their pros and cons to help designers quickly identify the most appropriate solutions for a particular project, or act as a starting point for developing new and/or project specific solutions. It highlights the challenges that designers and contractors must address together for successful support of tunnel openings, and the constraints that arise. It then describes the common structural forms of support, and how each form can mitigate the constraints, allowing an effective opening support system to be implemented. INTRODUCTION While only a small portion of the total excavated volume of a typical tunnel, cross passages are often one of the most complex elements of a bored tunnel to construct. Cross passages in soft ground typically involve ground improvement, groundwater control, and multiple temporary support measures to ensure safe construction in ground that has been overstressed due to the construction of the running tunnels. Permanent lining construction requires careful detailing of waterproofing and reinforcement to support both long term ground and water loads and support the broken out rings of the main lining. While there is not a great deal of literature specific to cross passage construction, the main issues are discussed in some detail by Lawrence and Taylor (2011). However, the temporary support of the running tunnel segmental linings during cross passage construction is not always given the attention it deserves. The authors have been unable to find much literature on the design of such systems, much less the considerations that have led to a particular solution. Lawrence and Taylor only mention two potential methods of support. It may be easy to dismiss the opening support as an inconsequential item, but selection of the wrong support type can have significant impacts on both cost and schedule."

Jan 1, 2016

By Lynton B. Manssen

Introduction Net Present Value (NPV) techniques are becoming widely used in industry as a standard analytical tool in making capital budgeting decisions. However, NPV techniques are often misused in "common practice." A comparison was made between the use of NPV techniques in common practice and an Adjusted Net Present Value (ANPV) approach to capital budgeting in the financial analysis of a mining project. The comparison was made by applying both methods to a hypothetical copper project. The intent of the analysis is to provide an example for practitioners to follow when financially analyzing mining (or other) projects. To maintain the thrust of the analysis, the project has been evaluated as a stand alone, total project. No consideration has been made of the division of cash flows accruing to various owners over the life of the project. This omission will not affect the comparative nature of the analysis. This discussion assumes that the reader is familiar with present value as a concept and as a tool in capital budgeting. Finance theory has embraced NPV analysis as the correct way to evaluate capital budgeting alternatives. Many articles have been written expounding the virtues of NPV over other capital budgeting methods, such as Internal Rate of Return (IRR), Payback, Accounting Rate of Return, and others. It is not the purpose of this article to review all of the literature in this area; suffice it to say that in academic circles NPV concepts are accepted as the norm. A survey by Schall, Sundem, and Geijsbeck (1978) indicates that major US companies are finally following in academia's footsteps. Fifty-six percent of the companies responding to the survey use NPV techniques in their capital budgeting process. Further, some 86% of the companies surveyed use discounted cash flow methods (NPV or IRR) for capital budgeting decisions. This compares with a survey by Klammer (1972) that showed 57% of companies using both techniques, a considerable increase in seven years. With the increasing use of NPV techniques in industry, there are certain uses in common practice that can give misleading results. Five common errors in NPV analysis of large projects are: • No distinction is made between real and nominal cashflows. • The discount rate(s) used in the NPV analysis is not formally adjusted for risk. • There is no distinction of possible differences in the riskiness of different project cash flows; i.e., revenue vs. depreciation. • There is no recognition of the cash benefits to the project from interest tax shields (interest payments on the project's debt that are tax deductible). • There is no clear recognition of subsidies to the project from concessionary debt financing. No Distinction Between Real and Nominal Cash Flows Often, expected cash flows for a project are stated as a mixture of real (in constant dollars) and nominal (in current dollars) cash flows. For example, expected revenue cash flows may be stated in real terms and depreciation may be stated in nominal terms. If cash flows are added together to give an after tax cash flow, and this single cash stream is discounted, care must be taken to ensure that cash flows are consistently stated. All cash flows should either be stated in nominal terms or in real terms. In addition, the discount rate used must be stated in the same terms as the cash flows being discounted. Real cash flows must be discounted using real discount rates and nominal cash flows using nominal discount rates. Discount Rate Not Adjusted Numerous methods for obtaining discount rates are used in common practice. Schall and others

Jan 6, 1983

By R. Jin

The hydrophobicity of six coals ranked from lignite to anthracite is studied through contact-angle measurements, bubble attachment-time measurements, FTIR spectroscopy, and Hallimond-tube flotation. The preliminary study shows that the hydrophobicity of coals can be told by the bubble attachment times of coals (a kinetic criterion) or by the contact angles (an - equilibrium criterion). A general agreement between flotation response of coals and measured bubble attachment times or contact angles is observed in the present study. However, the study also shows that the hydrophobicity of coals can be predicted by FTIR spectroscopy work with proper manipulation of the spectra. Both hydroxyl and carboxyl groups in the coals are proven by FTIR work to be responsible for the change of coal hydrophobicity. A new criterion for the hydrophilicity index of coals from FTIR spectra is introduced through the study.

Jan 1, 1987

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002, after the development of models for magnetic separators, hydroseparators and fine screens. A project funded the US Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Mittal plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2008

By Charles Stone, Eric Wang

A method for estimating geotechnical rock loads for shallow cut and cover subway stations is presented. Localized geotechnical conditions lead to extreme variations in rock loading on the walls of subway structures. Actual lateral rock stress on these structures can range from near zero to over four times the vertical in-situ rock stress. The primary factors affecting the actual lateral stress are intact and rock mass mechanical properties, excavation sequence, localized tectonic conditions, and potential future adjacent structures. The authors recommend using the AASHTO code value of 65 pounds per cubic foot (10 kN/m3) during concept design, followed by numerical analysis of rock wedges and stress measurement for final design.

Dec 1, 2022

By J. M. Goris

The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co., and the University of Utah, is conducting a field demonstration to evaluate the behavior of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-4BN stope. 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behavior of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modeled using the finite-element code UTAH III. Field data will be used to verify the modeling. In addition. a comparison between the effectiveness of conventional and birdcage cables will be made.

Jan 1, 1991

By Nick Rose, Robert Sharon, Mark Rantapaa

Development of the Northeast Layback of Barrick’s Betze-Post open pit commenced in June 2000 and was successfully completed to a height of 400m (1,300 ft) in January 2003. Following a brief exploration drilling campaign at the toe of the final slope, in-pit waste rock backfilling commenced, which will ultimately buttress the final wall. Instability initially occurred in late 2000, above the 5040 Level, as the slope height approached 120m (400 ft). As mining reached the 4680 Level, significant deformation was experienced over a slope height of 230m (760 ft). Slope stability was managed and targeted reserve recovery was achieved by executing complicated modifications of the mine plan, including splitting layback development, well placed offloading cuts, step-outs and mid-slope waste rock buttresses. Decision on timing of these modifying events was often dictated by review of deformation magnitudes and rates determined from continuous slope monitoring records. Design modifications were developed through continuing interpretive refinement of structural geology controls and groundwater distribution, and through stability re-assessments. This document presents an overview of the geological setting and material and strength conditions of the northeast sector of the Betze-Post open pit, followed by development experience leading to design and development of the Northeast Layback. Rock mechanics modeling, design details and geotechnical performance monitoring are then presented. Development experience, stabilizing adjustments to the original design and safety procedures for development and exploration activities are described. The document is finalized with conclusions and acknowledgements.

Jan 1, 2005

By Jeffrey B. Smith

Introduction The gas shortage is going to be with us for some time to come. If we can set aside political and industry rhetoric (along with subjective personal opinions), we still are confronted by two serious "facts of life": (1) for almost a decade the U.S. has been con¬suming natural gas at a greater rate than we have been finding new reserves; and (2) there is a finite amount of natural gas present within the earth&apos;s crust. Much of the known and easily exploitable sources of gas (the so-called "conventional" sources, such as the high permeability sand reservoirs of the Tertiary sequence along the Gulf Coast) already have been developed; their production is declining rapidly. The total producible reserves from con¬ventional gas reservoirs amount to only 216 Tcf, less than an 11-year supply. However, several large potential resources of natural gas remain to be developed. These "uncon¬ventional sources" have low permeability and/or peculiar producing characteristics. The DOE program for development of these unconventional sources of gas is called the enhanced gas recovery (EGR) program. The primary goal of this program is to provide a data base of resource characterization and production technology that will lead to commercial development. DOE will encourage and support in¬dustry participation in developing and demonstrating technologies needed to reach this goal. Unconventional Resources Four major unconventional resources of gas have a high potential for commercial development. There are other unconventional sources (such as gas hydrates) that are too poorly defined to warrant a major development thrust at this time. The four unconventional sources of gas currently included in the EGR program are: 1. The carbonaceous shales of Devonian age in the Appalachian, Illinois, and Michigan sedimentary basins are the targets of the Eastern Gas Shales Project (EGSP). 2. The low permeability, low porosity so-called "tight" gas sandstones of the Upper Cretaceous/Lower Tertiary in the Rocky Mountain areas constitute the resource target for the Western Gas Sands Project (WGSP). 3. The free methane trapped in coal beds of both the eastern and western U. S. constitute the Methane from Coal Beds Project (MCBP). 4. The abnormally high pressured, high-temperature saltwater aquifers of the Texas¬Louisiana gulf coast are targets of the Geopressured Aquifer Project (GPAP). Basic implementation strategy for these EGR projects involve (1) assessing and characterizing the resource potential of the resource; (2) conducting cost-shared field testing with industry to improve, develop, and demonstrate various stimulation and production technologies; (3) coordinating EGR activities within DOE and with other federal agencies (such as the Bureau of Mines) to minimize duplication; and (4) aiming all projects toward commercial development of the gas resources. EGSP What type of "geological animal" is the EGSP dealing with? While gas undeniably is related to the occurrence of natural fracture systems within the shale, the overall producing mechanism and precise location of fractured, gas¬bearing locales within each basin is still poorly understood. By developing reliable resource characterization techniques and applying effective stimulation technologies we intend to elevate the Devonian shale from the status of a potential gas resource to that of a proven gas reserve. Once we have done this the private sector can take over the large-scale commercial development of the Devonian shale gas resource. WGSP The second largest project (both in terms of complexity and level of funding) is the WGSP. The primary targets for this project are the low permeability (< 1 md) gas sandstones of the Piceance, Uintah, and Greater Green River basins and the Northern Great Plains Province. Project success in these four primary geologic locales will permit investigating additional low permeability sandstones in 16 other sedimentary basins. It ap¬pears that the only practical means of increasing permeability and resultant flow rates from these sandstones lies in the use of massive hydraulic fracturing techniques. Unfortunately, it is still too early to design such jobs with predictable results. MCBP The MCBP is to be involved in producing and utilizing methane derived from coal beds. The coal, like portions of the Devonian shale, is impermeable, highly fractured (termed "cleat" by

Jan 1, 1980