Search Documents

By W. K. Summers

During the past few years monitoring systems have been installed to measure the effects of environmental changes on the ground-water resource. The design of a monitoring system depends upon the designer's perception of how the environmental factors merge with his perception of the ground-water flow system. The validity and representativeness of measurements made during a monitoring program depend upon the validicy of the designer's perceptions and concepts. To optimize the design of a ground- water monitoring program the designer should make preliminary measurements to confirm his assumptions.

Jan 1, 1985

By Rodolfo V. de la Cruz

The in-situ deformability of a highly jointed basalt rock mass was determined by two distinctly different methods: one, by the NX- borehole jack method where the displacements of opposing curved platens were related to the applied hydraulic pressures, and; two, by the modified Goodman jack method where the tangential strains on the borehole walls were related to the induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX- borehole jack method. To explain the discrepancy, the influence of fractures and test variables such as depth, orientation, hole number and applied pressure on the calculated modulus of the rock mass were analyzed by factorial analysis and it was found that the orientations and depths of measurement has statistically significant effects. The in-situ deformability values obtained by non-linear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1982

By John P. Hunt

Early disseminated copper mineralization at Quebrada Blanca, Chile, accompanied 38 million year old quartz monzonite stocks and dikes. Early mineralization was followed by hydrothermal mineralization, mineralized breccias, and post-mineral faulting. After supergene leaching and enrichment, Quebrada Blanca was buried under late Tertiary gravels, and then partially re- exposed in Quaternary time. Based on work to date the orebody appears to contain more than one hundred million tons of plus one percent secondarily enriched copper ore, overlying several hundred million tons of protore averaging more than 0.5% copper. A source of industrial water appears to have been located. Pilot scale metallurgical tests, mine planning, and feasibility studies are in progress.

Jan 1, 1981

By Randolph E. Scheffel

Mill design and project execution are very demanding and interactive processes requiring the dedication and cooperation of many parties. The development philosophy which lead to the successful completion of Ranchers Exploration and Development Corporation's Escalante silver mill is reviewed. The project spanned 25 months from initial feasibility studies to start-up with the major construction effort requiring only 4 months. Mill performance for the second and third months after start-up, as well as fiscal 1983, is compared against the design parameters. Capital and operating costs are also discussed.

Jan 1, 1983

By James S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1981

By R. R. Dorfler

The existing regrind circuit at the Climax Operations uses sodium cyanide and Nokes reagent to reject pyrite, copper, and lead minerals. Laboratory flotation studies were performed using feed to flotation following first-stage regrinding. The effects of conditioning time, pH, and the concentration of depressants such as Nokes reagent and sodium cyanide on the rejection of pyrite, lead, and copper minerals were investigated. The metallurgical results indicate that, in the presence of depressants, the rejection of copper is strongly dependent on the pH. Preliminary mill testing confirmed the finding. The rejection of impurities is also dependent on conditioning time. The recovery of molybdenite is independent of the variables investigated.

Jan 1, 1981

By A. J. Wainwright

The Coffee Creek lode gold discoveries are located in the White Gold district (Dawson Range), west-central Yukon, 130 km south of Dawson City and 30 km south of the Golden Saddle gold deposit (Figure 1). Extensive structurally-controlled gold mineralization has been discovered during the 2010 and 2011 exploration drilling campaigns, highlighting this part of the Dawson Range as a significant emerging gold district. [ ] In this contribution we review the geological framework and describe the mineralization styles and metal signatures observed to date on the Coffee project. The main Coffee area is underlain by a 15 km by 4 km geochemical footprint, characterized by discrete linear gold-in-soil anomalies that correspond to various mineralized corridors. Of several mineralized areas tested in the past two drill seasons by diamond core and reverse-circulation (RC) drilling, we focus on the Supremo, Double Double, Latte and Kona zones; areas with the most information obtained from drilling thus far (Table 1; Figure 2).

Jan 1, 2012

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019

This paper addresses the valuation and development timing of an undeveloped mineral project. Traditional analysis has us developing the project immediately if its net present value (NPV) is positive. Option pricing theory finds that it is better to wait until the NPV of the property is significantly greater than zero before developing. Alternatively, when evaluating the development timing decision, we must calculate NPV using a higher "timing-adjusted" discount rate, and develop the property only if its NPV using this timing-adjusted discount rate is greater than zero. This paper uses option pricing ideas to convert this development timing advice into a more concrete and user-friendly decision rule: develop the project when its "development-timing NPV" is positive, this development-timing NPV being calculated using the normal discount rate.

Jan 1, 1997

By Wern-ping N. Chen

Pressure tunnel includes water-supply tunnels and tunnels for hydroelectrical power plants. Their design principles are different from those of water/wastewater/conveyance and transportation tunnels. Though theoretical pressure tunnel design guidelines exist, a comprehensive guide to summarize these guidelines to facilitate the planning and design of a pressure tunnel program is lacking. The purpose of this paper is to fulfill this need. It first provides key pressure tunnel design concepts in hard rock environment; then, it illustrates associated final lining design principles, including the design of un-reinforced concrete lining, steel lining, and reinforced concrete lining. Design diagrams and a flowchart for the reinforced concrete lining design are provided.

Dec 1, 2022

By B. J. Arnold

During the past three years, coal samples covering a range of coal rank, ash content, size consist, grindability, and moisture content have been tested for their flow properties using a triaxial shear tester that measures the unconfined yield strength in a compressed sample of coal. The ratio of this unconfined yield strength to the sample bulk density is part of the equation used by handling system manufacturers to calculate the critical arching or critical ratholing diameter needed to ensure that coal will flow from bunkers or bins. This ratio also serves as an index to compare the flow tested. To test the applicability of the index to predicting problems with coal flow, a series of tests were conducted at CO Inc.'s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. Tests covering ranges in size consist, moisture content, and ash content were conducted by first filling a small two-ton bin with coal and then emptying the bin at a pre-set discharge rate. The actual discharge rate from the bin under the various conditions tested was measured. Samples of the coal discharging from the bin were collected. One sample was analyzed for ash, moisture, and size consist; another sample was sent to the Iowa state University for trivial shear tests (supplying an index measurement). Actual flowability results from the bin were then compared to the measured index to determine the applicability of the handleability index in actually predicting coal flow problems. This paper describes the correlation between handleability index and bin flow and explains the next stages of the project.

Jan 1, 1992

By J. E. Urosek

The Mine safety and Health Administration (MSHA) formed the Mine Ventilation Bleeder and Gob Training Committee in 1993. This committee was charged with developing a training course designed to enhance the knowledge and understanding of practical bleeder ventilation systems. The course will probably include a discussion on the theory behind bleeder system design, an in-depth look at the strengths and weaknesses of the basic bleeder system types, case studies, and a review of the systems currently in use. A database on active underground bituminous coal mines, gob areas, and the bleeder systems presently used was developed from questionnaires distributed to nine Coal Mine Safety and Health (CMS&H) districts. Representative systems were selected for thorough investigation to develop case studies. This paper introduces some of the material to be included in the course, including a description of basic bleeder system designs, a review of a portion of the database, and facts about the gob areas and bleeder systems investigated for the development of case studies.

Jan 1, 1995

By T. T. Chen, J. L. Jambor, J. E. Dutrizac

A reconnaissance study of the neutralization potential of 30 diverse minerals, 28 of which are silicates and aluminosilicates, has shown that most of these minerals contribute minimally to the neutralization potential (NP) in standard static tests. Feldspars in particular give low NP values and would not be expected to attenuate the acidity to any significant extent in acid rock drainage settings. The BET-determined surface areas of the minerals vary considerably, and the large surface areas of some of the pulverized samples have clearly affected the NP values even though the standard static-test protocol was used for the preparation of the samples. The low NP values of most silicates and aluminosilicates are in general agreement with the laboratory-determined slow dissolution rates for these minerals. The results suggest that, in the prediction of whether rocks will be acid-producing, the most realistic measure is that of the carbonate content. In mine wastes from metalliferous ore deposits, the contribution to the NP by the non-carbonate gangue assemblage is unlikely to be more than a token amount until well after the establishment of an acid rock drainage situation.

Jan 1, 2000

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

By F. Hassan, M. A. Arafa

At El-Gedida iron ore deposits there is a block of about 30million tons neglected due to its higher sulfur content due to the presence of barite gangue minerals. From this bluk by magnetic separation dual concentrates of high grade iron concentrate (~65%Fe and total Sulfur of 0.26%) and the second concentrate is barite of (60.87% BaO and total impurities of less than 3%).

Jan 1, 1999

By D. W. Park

Longwall Strata Control and Maintenance System (LoSCoMS) is a software and data communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels including excessive shield load, low setting pressure, leg leakage and poor shield performance, eminent maintenance problems, etc. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems of their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 1998

By J. Killian, S. Cox

Many questions exist within the geotechnical industry as to the applicability of Strength Reduction Factor (SRF) values to the design acceptance criteria (DAC) of mining operations. There are many factors that contribute to changes in the SRF estimate, some of which are numerical (e.g. dilation angle) and some of which are geometric (e.g. model grid size)[1]. Numerous studies have confirmed equivalent values of SRF and FOS are found for soil slopes of limited height as presented in, [2] and [3]. However, significant deviation of the SRF value was observed for highly cohesive materials (rock slopes) of heights typically encountered in mining, [4]. This paper builds on the work presented in [4], providing a more rigorous examination of the modeling parameters that control the SRF estimate. The failure mechanism assumed for this study was a simple circular shear surface in a uniform material. Both LEM and numerical methods are suited well for analysis of this failure mechanism. A parametric study was completed to evaluate and test the relationships of key numerical variables that affect the estimated value of the SRF using Itasca’s Fast Lagrangian Analysis of Continua (FLACTM) software. The effect of groundwater has been tested and may be significant but is not presented as part of this body of work for brevity and simplicity of presentation.

Mar 2, 2022

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998

By Pafos Busch, Martin Fischer, Johannes Jaeger

The Spitzenberg Tunnel is a 600 m (1,970 ft) long twin tube motorway tunnel on Germany’s Autobahn A44 between Kassel and Eisenach. Since flexibility was considered to be very important in the continuously changing geological conditions, NATM was chosen as the construction method. When passing an old quarry with only 1,80 m (6 ft) of overburden, the excavation works became extraordinarily challenging. This paper not only describes the special methods, like double sidewall drifts and pipe umbrellas applied in this zone but also highlights the cooperation between the parties involved, which in combination made the project a joint success.

Jun 13, 2021