Search Documents

By A. Eftimie, M. Stanley

The World Bank Group (WBG) believes that extractive industries can make significant contribution to sustainable development and poverty reduction, providing that environmental, social, and corporate governance issues are properly managed. The WBG recognizes that stakeholders have legitimate concerns about the impact of extractive industries, and management proposals are built around the central theme that investments and policy advice in the extractive industries should lead to poverty reduction. To help governments create appropriate policy and regulatory frameworks, this paper focuses on the linkages between overarching policies and laws and the management / governance of extractive industries at the local communities. It encourages the use of new instruments designed to help ensure that local communities benefit from extractive industries.

Jan 1, 2005

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By Moussa Wone, Martino Scialpi, Colin LaVassar, Carlton Ray

The Potomac River Tunnel (PRT) is the next major phase of the DC Clean Rivers Program. The design-build PRT project includes a 5.5-mile-long, 18-foot-internaldiameter tunnel, seven shafts, and two underground connections to existing structures. Major challenges include tunnel boring machine (TBM) excavation though mixed-face conditions within a buried paleo-channel and an approximately 1,350-foot-long rock/ soil transition zone; construction beneath the elevated Whitehurst Freeway; tunneling beneath an existing luxury residential building and existing transit tunnels with limited clearance; and complex coordination with a variety of federal, regional, and local stakeholders. This paper describes the overall project scope, geotechnical conditions along the alignment, and primary design/construction challenges and mitigations.

Jun 13, 2021

By G. Robert Frey

INTRODUCTION This chapter on underground rotary drills briefly describes the equipment features, selection or applica¬tion criteria, safety features, and relative costs of both face and roof drills. After a brief description of the basic components, the application, safety, and cost con¬siderations will be explored. ROTARY DRILL COMPONENTS As illustrated in Fig. 1, an underground rotary drill consists of five basic components. These components are the energy system, chassis, boom, feed assembly, and operator's station. Energy System The energy system of a typical underground drill con¬sists of an electric motor, driving a hydraulic pump or pumps. Usually, the drill is equipped with a cable reel to store the trailing power cable from the portable power center in the mine. A simple control box is supplied to house electrical switchgear and protective devices. In addition to the pump, the hydraulic portion of the energy system includes the hydraulic cylinders, hydraulic tram motors, relief valves, control valves, etc., necessary to actuate the various machine functions. Chassis The chassis provides the frame or support structure for the other four basic components of the drill. Fre¬quently, it incorporates an oil reservoir for the hydraulic system. The chasis provides the support for the trans¬mission, which drives rubber tires or, in the case of some foreign machines, the crawler tracks. The steering link¬age and steering tires also may be considered as parts of the chassis. Boom The boom is the structure that supports the feed assembly; it is either hinged or pivoted on the front of the chassis. Hydraulic cylinders on the boom are used to lift or swing the boom relative to the chassis and to swivel or "roll" the feed assembly. Feed Assembly The feed assembly is made up of the support struc¬ture with an integral thrust mechanism, a rotation unit, centralizers to stabilize the auger, and a hose handling arrangement. In addition, most drills have an extension frame with a tilt device to aid in positioning the feed. Operator's Station The operator's station is the area from which the miner operates the drill. UNDERGROUND ROTARY DRILL APPLICATIONS Underground Face Drills Underground face drills are used in mining opera¬tions that utilize the conventional mining system. The face drill is used to drill holes in the exposed face of the material, and the face is then "shot" by means of explo¬sives or high pressure air. The loose material then is ready for loading and transporting from the face to the preparation plant. Typical specifications for under¬ground face drills are listed in Table 1. Certain parameters should be established as to where the drill is to be used and what is expected of it. To create an awareness of some of the considerations that too often are overlooked, some questions are listed that should be asked in conjunction with the selection or application of the proposed drills. Energy System: Can the drill be supplied with the proper voltage to match the available or proposed elec¬trical power system of the mine? Is the system 250, 460, 500, 550, or 950 v; dc or ac; 3-phase; 60 or 50 Hz? Is the drill equipped with an adequate electric motor to handle the proposed duty cycle? Typical motor power on a single-boom drill would range from 25 to 40 kW (35 to 50 hp); the nominal power for a dual-boom

Jan 1, 1982

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

By L. W. Berry

Drill and blast planning is critical to successful mine production, both in timing and in results. However, typical planning, reporting, and information exchange usually involves large quantities of data collated in a discordant set of spreadsheets, databases, and reports. Collecting, analyzing, modeling, and distributing all data necessary for efficient drill and blast operations is time consuming and cumbersome. MineSight Axis Drill and Blast provides an extensible core of functions, seamlessly integrated with other MineSight software tools, to make sense of this information. The benefits of improving the management of drilling and blasting processes are immense and result in improved fragmentation at a lower cost, improved shovel and truck productivity, and enhanced ore processing.

Jan 1, 2011

By James B. Fletcher

The Miami mine is located near the town of Miami, Gila County, Arizona. The Miami mine started mining in 1910 and finished in July, 1959. The orebody was divided and mined as follows: Tons High Grade 24,400,000 - Top slicing, sub-level caving, etc. Low Grade 105,100,000 - Block caving Mixed ore 9,800,000 - " Low Grade #2 13,100,000 - " Total Mining 152,400,000 GEOLOGY Ore minerals are largely in pre-Cambrian Pinal schist intruded by tertiary Schultz granite porphyry and covered to some extent by Quarternary Gila conglomerate. The structures are highly faulted and shattered. The Miami fault on the east cuts off the ore and the Pinto fault on the southwest caused re-oxidation of enriched sulphides producing mixed ore. MINERALOGY The chief mineral is chalcocite, with chalcopyrite, bornite, covellite, malachite, azurite, chrysocola, cuprite, native copper, and molybdenite as minor minerals. The ore minerals occur in seams, veinlets and disseminated particles. In block caving there is always some dilution, and drawing of ore stops when the grade drops past an economical point. This results in a small amount of copper left in the stopes below the capping. There is some copper in the capping, probably below 0.03% or less than 0.6 lbs. per ton. Over the low grade #2 orebody and portions of the high grade there was an oxide capping which was not mined. The crushed pilars are another source of copper. The leaching at Miami is an attempt to recover this last remaining copper of a worked-out mine. The enrichment at the Miami mine had gone more nearly to completion than most ore bodies in the southwest. There is practically no pyrite in the capping and very little in the ore.

Jan 1, 1971

By E. Lee

The behavior of As bioleaching using Acidithiobacillus thiooxidans (A. thiooxidans) in mine tailings containing highly concentrated As contents (i.e., As=33877 mg/kg) was systematically evaluated according to the changes in temperature (25?40°C, pulp density=0.5%, pH=1.8), pulp density (0.5?4%, temp=30°C, pH=1.8), and initial pH(1.8?2.2, temp=30°C, pulp density=0.5%). The changes in temperature and pulp density affected the As leaching behavior more than the change in initial pH did. Based on the pH and oxidation-reduction potential (ORP) results, the As leaching was attributed to solution acidification. In particular, As leaching was accelerated with increasing sulfate production in the reacting solution. After bioleaching, surface of tailings examined that many pores which dissolved As were formed by a chemical reaction due to bacteria. The As bioleaching efficiency by A. thiooxidans was enhanced by the oxidation of both the added elemental sulfur and the sulfur compounds in the mine tailings. The As bioleaching efficiency was maximized at 50.5% under conditions of an initial pH of 2.2, reaction temperature of 30°C, and pulp density of 0.5%.

Feb 23, 2014

By J. J. Komadina

Since the advent of resin-in-pulp (RIP) technology for treatment of uranium-bearing ores in the 1950?s to current carbon-in-pulp (CIP) processing of gold values, metallurgies and operators alike have wrestled with the problem of interstage screening. Early gold CIP plants such as at Homestake utilized externally mounted vibrating screens in conjunction with air lifts to effect carbon-pulp disengagement. Other operations world-wide have likewise adopted this technique with varying degrees of success. Subsequent development of in-tank launder screens both in South Africa and the United States have been of the air cleaned variety (EPAC)

Jan 1, 1988

By R. Vergunst, E. A. Devuyst, G. Robbins

By the middle of 1989 Inco will have applied its patented cyanide removal technology to seventeen commercial operations. Removal of cyanide from CIL slurry tailings is applied at Equity Silver and Inco's new 1.200 mtpd mill at Inco/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3.600 mtpd), Canamax's Ketza River (360 mtpd) and Westmin's Silbak Premier (2000 tpd) operations. Repulped tailings from Merrill-Crowe flowsheets are treated at Total Erikson's Mount Skukum (300 mtpd) and Skyline's Johnny Mountain (200 mtpd) mills and barren bleed at Inco/Queenston's McBean mill (500 mtpd). Lynngold's MacLellan mill (1800 mtpd) and ERG (40.000 mtpd) treat pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating and two other plating shops in Ontario. Details regarding some of the above operations are given. Operating and capital cost estimates for various treatment options are discussed.

Jan 1, 1989

By L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, Colorado, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained, and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward sloping (20 pct) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Christopher J. Bise

INTRODUCTION The principal means for transporting men, supplies, and mined material in an underground or surface mine are rail systems, conveyor belt systems, or a combination of the two. Typically, large underground mines use rail haulage from the mining sections to the hoist, with conveyor belts being used within the sections. Small mines use conveyor belts in the mains and sub- mains as well as in the panels. The size and layout of surface mines also contribute to variations in the way these haulage systems are applied. The following sections address the typical problems confronting mining engineers in designing these haul- age systems. For rail, these include rail selection and turnout design, locomotive tractive-effort calculation, and motor sizing. Belt haulage calculations include belt width and speed specifications, tension and take- up requirements, idler spacings, and motor sizing. TRACK LAYOUTS Introduction The adequacy of mine track layouts is dependent upon such factors as rail weight (Table l), suitable ties, a well-drained roadbed, and properly designed curves, grades, and track alignment. As long as the installation conforms to the manufacturer's recommendations, good service can be expected from the rail system. Typically, mining-engineering calculations for rack layouts have dealt almost exclusively with the design of turnouts. As such, the following section provides the necessary information for computing the theoretically correct dimensions of turnouts. Turnout Design Fig. 1 shows a typical turnout with an identification of the component parts. Fig. 2 identifies the variables that are used to determine the turnout dimensions. The formulas that concern the mining engineer are those listed: [ ]

Jan 1, 1986

By Elif Emil-Kaya

Samarium (Sm), as one of the rare earth elements (REEs), has gained significant attention in the production of samarium- cobalt (SmCo) magnets due to their high corrosion and oxidation resistance, as well as their high-temperature stability. SmCo magnets find applications in various industries, including but not limited to national defense, aerospace, military and medical equipment. Sm and Co have been classified as critical metals due to their economic importance and supply risk. Recovering Sm from SmCo magnets is an effective method to ensure a stable supply. The present study investigates an integrated hydrometallurgical treatment and combustion process for the preparation of rare earth oxide (Sm2O3 ) powders from SmCo. Initially, SmCo powders are exposed to nitric acid, and the resulting slurry is selectively oxidized at 250 °C to obtain Sm(NO3)3 , Co2O3 and Fe2O3 . Subsequently, the selectively oxidized powders are leached with water to extract Sm. Sm2O3 powders are produced from the obtained leaching solution using an energy- and time-efficient solution combustion process. Finally, the optimal conditions for the production of Sm2O3 are identified, and the produced powder is characterized through X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis.

Nov 1, 2024

By S. C. Chelgani

The Thor lake deposit is a world class resource of rare earth (REE) metals and minerals in Canada. Development work to optimize a REE mineral recovery process flow sheet is underway, however, given the ore mineralogy; the developed reagent scheme is relatively complex. As part of a research project, micro flotation tests were conducted on a feed sample in order to examine factors affecting stream partitioning. SEM-EDX was performed to evaluate variability in grain composition between streams (concentrate and tails) and TOF-SIMS surface analysis was used to determine statistically significant differences in surface species particularly related to potential activation (or depression) of the examined mineral phases. SEM-EDX analysis reveal that the concentrate has a significantly higher proportion of REE bearing grains (carbonates and phosphates) relative to the tail (almost none were identified). Spectral fingerprinting by TOF-SIMS has allowed for the identification of all reagent species investigated. Reagent signal intensity discrimination on test stream mineral surfaces was observed by the TOF-SIMS analysis using reagents at plant concentration levels. TOF-SIMS analysis confirmed that REE bearing grains reporting to the concentrate are doing so in response to collector attachment whereas grains reporting to the tail are doing so in response to a lack of collector and/or in combination with the presence of the depressant. The surface analysis of gangue phases reveal a similar reagent discrimination; the signal intensity of collector species was significantly higher on the concentrate samples relative to the tails while depressant species were significantly enriched on the surface of the gangue phases in the tail samples. A detailed evaluation of the surface species representing the various reagents used in flotation scheme revealed a distinct competitive relationship between two of the reagents. The surface analysis identified that when used in concurrently, there appears to be a negative feedback resulting in a significant reduction in loading for several of the collectors on grains reporting to the concentrate. An evaluation of the effect of reagents on REE mineral in pilot plant is currently under way. Key words: Rare earth minerals, Flotation, Surface chemistry, TOF-SIMS, SEM-EDX

Feb 27, 2013

By Curt Swanson, David C. Mathy, Dru R. Nielson, Kent VonAspern

In 1997, Central Contra Costa Sanitary District undertook the design of the Martinez East Side Trunk Sewer Improvements Project. Microtunneling was specified for approximately 1,035 meters (3,400 feet) of 600-mm (24-inch)diameter pipeline to be installed through estuarine soil deposits (San Francisco Bay Mud) and alluvium beneath the congested city streets of downtown Martinez, California. Directional drilling was specified for approximately 275 meters (900feet) of 200-mm (8-inch) diameter pipeline in four separate segments to be drilled through bedrock within narrow utility easements between residential properties. This paper presents a case history for the design and construction of themicrotunneling and directional drilling aspects of the project.

Jan 1, 1999

By A. L. Miller, A. J. Chambers, P. R. Griffiths, D. A. Parks

"Diesel engines are one of the primary contributors to the presence of nano and ultrafine aerosols in ambient air and occupational environments. Exposure to diesel emissions has been shown to contribute to various adverse health outcomes of the pulmonary system and cardiovascular system. Currently diesel emissions in the workplace are monitored by way of collecting the aerosol onto filters, which are then sent to a lab for thermal-optical analysis using the NIOSH 5040 method, which measures elemental and organic carbon explicitly. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of diesel particulate matter (DPM) before the problem is identified. To remedy this, researchers from the National Institute for Occupational Safety and Health (NIOSH) are seeking to develop a field-portable method for measuring elemental and organic carbon in DPM aerosols. In the current study, we investigated the use of Fourier transform mid-infrared (FT-IR) spectrometry, which lends itself more readily to implementation in a real-time system than do the thermal-optical analysis methods. We have demonstrated a method for measuring organic and elemental carbon in DPM for a broad range of organic carbon (OC) to elemental carbon (EC) ratios (from 50.3 to 0.8). The ability to handle a wide range of OC to EC ratios is critical given the evolving diesel technology. INTRODUCTION Respiratory illnesses are common in mining industry workers [1] and exposures to toxic aerosols such as DPM can result in serious respiratory illness [2]. Health studies show a correlation between workplace exposure to diesel exhaust and an increased risk of lung cancer [3-8]. The International Agency for Research on Cancer (IARC) has characterized diesel exhaust as a human carcinogen [9], and similar classifications have been made by the World Health Organization and the California Air Resource Board. A recent study [10] suggests that the risk of lung cancer is approximately three times greater for heavily exposed workers. When compared to other aerosols in the mine environment, the settling time of DPM is significantly longer than that of dust due to their small particle size (typically < 1 µm) [11]. Additionally, submicron particles (such as DPM) are deposited in the lungs much more efficiently than their larger counterparts such as dust [12]. Previous studies focusing on particle morphology [13] show that the largest mass contributor to lung disease in mining is elemental carbon, which provides a solid core onto which hydrocarbons are adsorbed. In accord with those findings the Mine Safety and Health Administration (MSHA) decided on submicron total carbon as a surrogate for monitoring diesel particulate matter in the mining environment."

Jan 1, 2018

By B. K. Blashich

In responding to mine fires and explosions, accurate and timely analysis of the mine atmosphere is critical in making decisions regarding firefighting, mine rescue and mine recovery operations. For many years instantaneous analyses were available to rescue workers using handheld or portable gas detection equipment, including infrared, electrochemical, or catalytic measuring devices for a limited number of specific gases such as oxygen, methane, carbon monoxide and carbon dioxide. Instantaneous sensing technology is not available for all gases, such as nitrogen and hydrocarbons, found in a mine fire atmosphere and cross-sensitivity can be a problem with this technology. For these reasons, air samples are collected for injection into a gas chromatograph for a complete and accurate analysis for all gases including oxygen, nitrogen, methane, carbon monoxide and carbon dioxide, as well as ?fire gases? such as hydrogen, ethylene, ethane, and acetylene. This method requires additional time for transporting the samples to the laboratory near the mine, as well as an instrument operator to inject the samples for analysis. The use of a portable micro gas chromatograph with a continuous and automatic injection system has been implemented by the Mine Safety and Health Administration (MSHA) during mine recovery operations. The device directly samples the mine atmosphere from an underground location every twelve minutes and automatically analyzes the samples for all of the mine fire gases. The portable unit utilizes micro technology and the operating software has been modified to perform the calculation of sample results in and Excel® spreadsheet without user interaction. This paper describes the micro gas chromatograph system and its use at a recent mine recovery operation. The automated remote operation of the micro gas chromatograph has been shown to be a good alternative to infrared and electrochemical sensors used for mine atmosphere analysis.

Jan 1, 2009

By Andrew Cho, Changsoo (Kevin) Moon, Richard Flanagan, Brian Larsen

"INTRODUCTION Project Background The U.S. Army Corps of Engineers (USACE)/Port Authority of New York & New Jersey (PANYNJ), as part of their New York and New Jersey Harbor Deepening Project, will dredge this shipping channel to a depth of 16.5 m below mean low water (MLW). By deepening the channel, the new generation of larger, “post-panamax” container ships coming to U.S. waters as a result of the expansion of Panama Canal can be accommodated in local marine terminals, helping to retain the nearly 300,000 jobs and $12 billion in annual wages the PANYNJ provides to the region. The existing siphons are situated at a depth that could be compromised by the planned dredging of the channel (nycedc.com). The purpose of this project is to build a new 1.83 m diameter water main inside a 3.66m diameter tunnel replacing the two existing siphons in order to provide the necessary backup water supply to Staten Island across the Anchorage Channel within the Upper New York Bay from Brooklyn. The proposed tunnel is approximately 2.9 km long and at a depth of at least 26 m below MLW. The project is funded jointly by New York City’s Department of Environmental Protection (NYCDEP) and PANYNJ and is managed by New York City Economic Development Corporation (NYCEDC). The contractor of the project is Tully/OHL JV, the designer is CDM/HMM JV, and the CM is LiRo/PB JV. History of New York City’s Soft Ground Tunneling The New York City area has a relatively long history of soft ground tunneling, commencing in the late 19th century. Construction of the first Hudson River tunnel crossings was begun (but not completed) in 1874 for the Hudson & Manhattan Railroad using compressed air supplying a shield. The work continued intermittently until the project finally opened for service in 1907. These 1.72km long tunnels (maximum depths of 29 m) are still in operation and now operated as the PATH Tunnels. They are approximately 5.5m diameter utilizing cast iron segments. The river bed consisted of primarily silt with shallow rock near the New York side. Air “leaks” occurred during the compressed air excavations resulting in some serious “blows” with water and soil entering the tunnel, including one incident with 20 deaths."

Jan 1, 2016

By I. Yildirim

Water contact angles of talc powders were determined from the values of the heats of immersion measured using a flow microcalorimeter. The results were used to calculate the contact angles using a rigorous thermodynamic relation. In the present work, the calculation was carried out using the temperature coefficient of the contact angles determined experimentally using another method. The results obtained in the present work on several different talc samples are compared with those obtained using other methods.

Jan 1, 2001

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020