Search Documents

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

By James Wonneberg, William Edgerton

"Today’s underground construction megaprojects are tremendous feats of engineering on a massive scale, excavating through ground conditions once thought impossible, using new and innovative contracting practices. But one important truth remains unchanged; projects are built by people. What separates winning projects from the rest? Great people, working in great organizations. In straight-talk fashion this paper sets forth fundamental differences between good project leaders and bad ones, on topics ranging from client relations, design management, and scheduling, to use of the whiteboard, and everything in between. Broadly applicable to all corners of project delivery, this paper will resonate with project leaders from around the world and help identify skills necessary to succeed in the management of underground facilities. A NOTE FROM THE AUTHORS This is a training document, and not really a “paper” per se. We have attempted to tackle some big and potentially complex topics using bite-sized paragraphs, each of which are intended to promote thoughtful introspection and dialog. So please feel free to skip around, or even set this document down while you reflect on your own personal experiences, tactics, and philosophies. We have found that providing examples of “what not to do” is oftentimes more instructive than simply listing “what to do”, hence the Good/Bad format of this document. Please note that “PM” refers loosely to anyone on the project management team not just the “Project Manager”. We also wish to preface this with the following cautionary statements: • The authors do not pretend to be the “Good PM” in all cases. In fact, we’re almost certainly the “Bad PM” for some. We aim to improve on those areas. • It has been said that “The only real training for leadership is leadership.” (Antony Jay) We all started somewhere, and nobody has 20 years of experience on day one. • Converting this text into some sort of prescriptive checklist would be a disservice to the evolution of project management. Our world – and our awareness of it – is constantly changing. We must always be open minded to new ideas and different perspectives on project delivery."

Jan 1, 2016

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By H. R. Coles

Test work conducted in the 6.4 and 10.52 m Aerofall Mills at the Iron Ore Company of Canada Carol Project showed that the conventionally used ?deflector?-type liners which form the basic principle of Aerofall Mill grinding did not necessarily provide the best grinding performance. A new design, using low profile liners incorporating radial ribs of a proper height, actually improved the mill throughput in the order of 9 to 20% without sacrificing grinding efficiency. In addition, the new design reduced liner weight and scrap losses, which resulted in a reduction of liner consumption by 25%. It provided better protection to the mill shell and reduced the overall maintenance cost for the mill

Jan 1, 1980

Baja Mining is currently constructing the Boleo metallurgical plant in Santa Rosalia, Mexico to recover copper, cobalt, zinc and possibly manganese products from the Boleo ore. The process involves an acid seawater leach of the whole ore followed by solid-liquid separation and washing of the leach residue. Solvent extraction is used to separate copper, cobalt and zinc from solution. Copper and cobalt are recovered as cathode metal products and zinc as a zinc sulphate monohydrate. Manganese may be directly precipitated as manganese carbonate which can be used as a feedstock for manganese metal production. Laboratory testing has continued to refine various aspects of the process including iron removal, cobalt and zinc solvent extraction, cadmium cementation, cobalt electrowinning and manganese metal electrowinning. The results of this testing are reported in this paper.

Jan 1, 2012

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite is one of the main players in the stability of drilling mud. Its particle size and particle size distribution significantly affect drilling mud’s rheological properties. Although the Specifications for Drilling Fluids Materials report on Oil Companies Material Association (OCMA)-grade bentonite states that the API recommended powder having 2.5 percent mass fraction as the maximum value of residue of diameter greater than 75 μm, there is no other information on the specific size distribution for API bentonite. It was found that API bentonite has a specific size distribution with specific mixing weights. It is important to investigate why that mixture represents the optimum properties of drilling mud and how each individual size fraction has a specific function in the mixture. To clarify the effect of individual size as well as the collective effect of the size distribution, API bentonite was classified into different size fractions, with each tested separately for controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness and packing density.

By Oscar Cabello, Luis Mendieta, Maribel Guzman

Mineral flotation processes generate large volumes of tailings, which must be disposed of efficiently and safely. In addition to dry stack disposal, the possibility of reusing these tailings as aggregates in shotcrete is an interesting alternative. Tailings samples from a mining operation in southern Peru were characterized by granulometric analysis, X-ray diffraction and Scanning Electron Microscopy. Concrete samples were obtained with different tailings formulations. The samples were subsequently subjected to geomechanical testing. The results showed that replacing 20% to 30% of the tailings with aggregates in shotcrete production achieved compressive strengths exceeding 30 MPa after 28 days of curing, with an energy absorption capacity of 500 joules. Results show that this shotcrete can be used in the support stage of the mining cycle in underground mining.

Feb 22, 2026

By L. E. Baker, M. J. Leck

OSIRIS is a continuous monitoring system for respirable dust which has been specifically designed for mining and related industries. By using the latest microprocessor technology, OSIRIS provides a sophisticated dust measuring system which is a cost effective alternative to regular gravimetric sampling. The system is certified intrinsically safe for use underground. Up to eight underground OSIRIS sensors can be controlled and monitored by a single IBM PC computer located at the mine surface. This computer provides continuous and instantaneous information about the dust concentrations at the sites being monitored. Information is available in tabular and graphical form. The paper gives details of proving trials of the OSIRIS system in some UK coal mines. During these trials, adjacent OSIRIS sensors placed on the same underground roadway cross-section gave virtually identical results. Throughout a good correlation was obtained with conventional gravimetric dust samples. The OSIRIS equipment proved both reliable and easy to operate. OSIRIS was designed and developed by the Safety Engineering Laboratory of the UK Health and Safety Executive. It is now available commercially and is being

Jan 1, 1987

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By Ali Yalçin

The study area is located in the NW of Uluborlu (Isparta). Massive limestones and alluvial deposits form the lithological units of the study area. The average thickness of the alluvium deposit consisting mainly of light brown - red colored and fine grained clastic sediments which derived from the limestone is about 10 meters. The aim of this study to investigate the uses of this alluvial sediments as tile - brick material. For this aim, disturbed and undisturbed samples have been taken from different depths in the alluvial deposits. Mineralogical compositions have been determined by XRD and major oxide contents by XRF. Laboratory experiments have been carried out to determine the technological properties of the samples. The selected major oxide contents of samples vary between A12O3 (24.6 - 24.12 wt %), CaO (0.76 - 4.27 wt %), Fe2O3 (10.21 - 10.29 wt %), MgO2 (1.25 - 1.51 wt %). CaCO3 and MgCO3 values calculated from the geochemical analyses, are between 1.55 - 1.62 and 2.62 - 3.17 respectively. The ratios of grain size of the samples are 82 % for < 0.2 mm and 5 % for > 3 mm. Geochemical analyses and technological features of the samples indicate that these fine grained sediments of alluvial deposit are suitable in terms of uses as tile - brick material. The potential reserve of this tile - brick material has been determined as 40 million tones.

Jan 1, 2005

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification such as nickel (Ni), cobalt (Co), copper (Cu) and manganese (Mn) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte; ammoniacal leaching (gas reduction or Cuprion); and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered the pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stem from the 1970s and 1980s, and are not always easily accessible. This article details the series of tests conducted and provides updated results obtained — high Ni/Co/Cu recovery with limited manganese/iron (Mn/Fe) — as well as comments on the potential treatment options on the product solution and residue.

Sep 1, 2025

By F. F. Peng

The raw-coal feeding system and the upward medium current flow in a dense-medium vessel (DMV) are, in addition to the residence time of particles in the separator, important factors for efficient coarse particle separation. The feed material from a raw coal screen and/or pre-wet screen merge with the major volume of circulating medium as push medium, guided by an adjustable submergence baffle plate deep fed into the separator for effective separation. The remaining volume of the circulating medium enters from the purge and drain hoppers at the bottom of the DMV. This generates a gentle upward medium current flow in the separator, which prevents dense medium stratification/settling and merges as part of the push medium. A two-dimensional, two-phase model developed using computational fluid dynamics (CFD) is used to describe the flow pattern and evaluate the function of the dip plate for understanding the mechanisms of particle separation in the separator. The particle movement in the DMV is also tracked to investigate the major operating parameters affecting the separation performance of the DMV. The simulation results of the DMV separation performance are validated by in-plant test data.

Jan 1, 2007

By A. E. Ketler

Powerful, yet inexpensive, personal computers running Windows-95 operating systems provide powerful mine-wide monitoring capabilities when properly engineered. Long awaited conductivity over LAN, phone and Internet links provide new dimensions for sharing information throughout an operator&apos;s organization, in- deed around the world. On-line data analysis, archival data storage and historical trend viewing generate shared inputs to production, safety and maintenance personnel. Five years in development, Rel-Tek&apos;s new EZ-Trol/W-DX system was engineered around the pilfalls of a Windows environment. It now offers higher speeds, 3D animated graphics and long distance telemetry - all with better reliability than ever before possible. The ubiquitous DDS utility inherent in most Windows was discarded in favor of a lightning fast RAM format. Several ponderous interpretive programs were redesigned into a single compiled entity, thus avoiding the overhead from message conversion, handshaking and transfer. To make the system user friendly, a &apos;Wizard" utility helps operators set up and reconfigure their systems on site. In-mine data acquisition telemetry was also re- vamped, incorporating a unique noise avoidance scheme, dubbed the "DX" bus - enabling longer distances and higher reliability. 12- bit analog conversion provides the enhanced resolution needed for field scaling auto-cal sensors. By mid &apos;96, eight EZ-TROLMI- DX systems were up and running, several for more than a year. Factory updating and assistance are possible over a phone or Internet link. Our factory testing of components routinely includes actual operation at 2400 BAUD over 14 miles of twisted pair wires.

Jan 1, 1997

By W. -C. Huang

In this paper, a methodology for the reliability assessment of geogrid-reinforced unpaved roadways is presented, by taking into account the variability of the subgrade?s undrained shear strength. Analyses are performed using the Point Estimate Method and the Monte Carlo simulations technique. The undrained shear strength is represented by its correlation with the California Bearing Ratio and it is modeled as a random variable following a long-normal distribution. Analyses are performed for different types of reinforcement. The study provides a quantitative assessment of the variation of the system?s probability of failure with this parameter. Overall, the approach suggested in this study may be considered as a complementary approach on the traditional concepts of global or partial safety factors.

Jan 1, 2008

In this paper, the logic and the capabilities of a long term production planning method for open pit mining are presented. The method is the first attempt in obtaining simultaneous solutions to the four interrelated parameters of open pit mining; 1) the mine life, 2) the specific blocks to be mined each year, 3) the amount of ore and waste to be mined each year, and 4) the ultimate pit limits. An efficient cutoff grade can also be obtained through a sensitivity analysis. None of the existing methods can bring such a comprehensive solution to the problem. A production plan for a real life gold deposit is given to illustrate the logic and the capabilities of the method.

Jan 1, 1993

By Fiona M. Doyle Garner

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°-200°C. Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions of various metals, singly and in mixtures. Single solutions of Fe, Xi, Cu, Mg, and tin precipitated aFe2O3, Ni(OH)2, Cu2O, Mg(OH) 2 and ?Mn203 respectively during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe20k. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versa- tic solutions are similar to those for iron hydrolysis in aqueous solutions. Infrared spec- troscopy and thin-layer chromatography of mixed iron-nickel Versatic solutions indicated that mixed Fe-Ni carboxylate complexes are present. Magnetic interactions between mixed complexes are thought to be responsible for the homogeneous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1984

By J. D. Miller

X-ray computed tomography (CT) techniques have been developed for the medical services field in order to provide accurate internal images of the human body.(l-7) Now, a decade later, CT techniques are starting to be used in non-medical applications such as, non-destructive testing(8), flow pattern analysis(9), drill core examination (10,11), and coal characterization(12,13). In these fields of application, CT techniques offer the potential to extend our knowledge and understanding beyond that provided by more traditional methods of analysis. Although, CT systems involve very specialized and expensive equipment, the advantage of x-ray CT in revealing the detailed internal structure of an opaque material non-destructively should make it an important tool to provide a more complete analysis of mineral processing phenomena. X-ray CT systems generally consist of an x-ray source/collimation unit and a detector/data acquisition unit. The object to be examined is placed between the two functional units as shown in Figure 1. With this system the density array of selected cross sections of a chosen opaque object can be obtained in two dimensions. There are numerous areas in mineral processing to which x-ray CT technology can be applied and it is the aim of this article to identify these potential areas noting the advantages and limitations of the technology. Particular emphasis is placed on particle composition distribution and multiphase fluid flow measurements. In the case of particle composition distribution, liberation analysis and coal washability are considered. While in the case of multiphase fluid flow, swirl flow in the air-sparged hydrocyclone is given by way of example.

Jan 1, 1989

By Pat C. Hautala, J. R. Hoskins

This is a new era for the minerals industry. Never before has there been more need for effective communication. So said Robert Anderson, chairman and chief executive officer of Hanna Mining Co. He was speaking to the American Mining Congress&apos;s Communication Workshop. The question is whether there is enough industry concern to meet the challenge. Anderson observed that increased workshop attendance, in continuing tough times, reflects the industry&apos;s concern for communication. But, why were students, faculty, engineers, supervisors, and managers not at the conference? Communication applies to every manager, Anderson said. But he was the only operating manager present. And only one company sent operating supervisors. The remaining conference participants were public relations personnel, generally with nonmining backgrounds. And the program dealt mostly with public relations issues. Role of Communication in the Minerals Industry. It is well known that the minerals industry faces economic, political, and social problems. Economic shifts and foreign competition have created an international minerals industry and an international marketplace. This, in turn, calls for worldwide communication. Other factors effecting communication are: • Governmental protectionism as well as regulatory reforms call for increased interaction with governing officials. • Changing social values have created environmental issues and anti-industry attitudes. This intensifies the need for improved public relations. • Traditional work values are shifting towards self-actualization and humanistic movements. The work force is better educated and more informed. Employees demand more satisfaction, equality, and job autonomy. • The mining industry&apos;s task of managing its human resources is complicated by layoffs, job uncertainties, and bleak outlooks concerning employee morale and motivation. Technology and Information for a New Era As noted, this is a new communications era, one propelled by technology and information. Technology has led to reduced demand for raw materials by developing substitutes. Copper demand, for example, will never fully recover. Copper cables are replaced by fiberoptics; copper transmission lines, with aluminum. Technology has shifted the US from traditional to high tech and service industries. The speed, frequency, and scope of information transmission have greatly increased. But the most significant characteristic of this information is not the pace of advancing technology. It is the dramatic increase in the importance and frequency of our personal transactions. Knowledge has replaced raw materials and capital as the strategic resource. Information has replaced energy as the transforming resource. And the game against nature has become an interpersonal game (D. Bell, Post-industrial society, Physics Today, &apos;76). In Megatrends, John Naisbitt says that information will soon double every 20 months. So, professionals will become "information workers." And communication will be the life channel of the information age. Thomas Wolfe said you can&apos;t go home again. Hanna Anderson said we are, indeed, facing a new day. It will never again be "business as usual." We must move into the information age with the rest of society. We cannot trust that the world will continue to rely on our products. Nor can we place the responsibility and control for problems and solutions outside the minerals industry. Improved communication is not a panacea. But, Anderson said, it is critical to the minerals industry. What is Communication? The word communication is overused. It is applied to every aspect of our lives. Satirist Tom Lehrer got sick of hearing about the need to communicate. He said, "It seems to me that if someone is having all that trouble communicating, the very least he can do is shut up!" Obviously, we cannot follow that advice (though we might wish that some others would do so). Communication is always going on. It is inevitable. Yet we have many misconceptions about com-

Jan 1, 1985

By T. M. Klemetti, T. J. Batchler, T. Matthews

From 2013–2017, there were over 1,120 documented injuries, including fourteen fatalities, from ground falls in underground mines in the United States (MSHA 2017). The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. The load-displacement characteristics of an 8-ft x 12-ft area of 8-gauge welded-wire screen were evaluated using a test frame designed for testing multiple load-pull locations. In previous tests, load-pull contact was always in the center of the bolted screen section. In this study, larger pull contact areas are used to simulate roof falls. The information obtained in this and similar studies can be used to better understand the loading behavior and surface control capability of roof screen in underground mines. INTRODUCTION AND BACKGROUND The large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded-wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in NIOSH’s Bruceton Research Center Laboratory in Pittsburgh, PA. Previous tests to evaluate the performance characteristics of various types of screen have been conducted by the University of Alberta (Tannant, 2001). In this study, the load-displacement properties of welded-wire, chain-link, and expanded-metal mesh were measured by performing full-scale pull tests. A flat steel plate was pulled through a screen test sample that was bolted to a special test frame while the pulling force and mesh displacement were measured. These tests established the general load-displacement behavior of the screen. Peak load capacities and stiffness were determined for each screen type, showing how welded-wire mesh has a much stiffer initial loading response, whereas chain-link and expanded-metal mesh have large displacement capabilities and exhibit significant post-peak ductility.

Jan 1, 2019

By J. L. Moreno, A. L. Williamson, R. D. Bartlett

Large open pit mines in desert climates, such as the Phelps Dodge Morenci copper mine in Arizona, can create groundwater cones-of-depression of considerable size and stability. The hydraulic containment provided by the groundwater depression prevents migration of process solutions into the surrounding regional aquifer. Copper leach operations that fall within the groundwater depression may not require costly lining if passive containment can be demonstrated. An approach is presented in this paper that was successfully used to demonstrate passive containment. The approach includes a combination of groundwater modeling and a water balance analysis of leaching operations failing within or immediately near the open pit.

Jan 1, 1999