Search Documents

By John Barber

The Deep Ore Zone (DOZ) Mine is PT Freeport Indonesia's (PTFI) newest operation. Production at the mine began in September 2000. The DOZ Mine produces 25 kt/d (27,500 stpd) using mechanized block cave mining methods. The DOZ Mine has several major improvements when compared with previous block cave mines in the district. It has an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system. PTFI's copper and gold mining complex is located in the Ertsberg mining district in Irian Jaya, Indonesia (Fig. 1). The Ertsberg district is located in the Sudirman Mountains at elevations from 3,000 to 4,500 m (9,800 to 14,700 ft) above sea level. The topography is extremely rugged and rainfall in the mine area averages 3,000 mm/a (118 in./year). Freeport began production in the district in 1972 when the mill began processing ore from the Ertsberg openpit. Underground mining began in 1980 when the Gunung Bijih Timur-Ertsberg East (GBT) Mine was brought online using block caving methods. In 1991, the GBT Mine reached a maximum production rate of 28 kt/d (31,000 stpd). Ore from the mine was exhausted in 1994. The Intermediate Ore Zone (IOZ) was brought into production in 1994. It, too, used block caving methods and had a design rate of 10 kt/d (11,000 stpd). The IOZ is currently producing at a rate of 21 kt/ d (23,000 stpd). The DOZ was discovered in the mid-1980s by deep drilling from the GBT. The GBT, IOZ and DOZ deposits are all situated in the Ertsberg East Skarn System (EESS). In 1993, the first of several studies was completed that indicated that portions of the DOZ Mine could be economically mined using block caving methods. Limited development was started in 1995. Full-scale development and construction began in late 1997. The crusher and conveying system began operating during the first quarter 2000. The first of two main exhaust shafts has been com¬missioned, along with three of the four new main fans. The second exhaust shaft and fourth main fan will be in service by the end of 2001. Undercutting and production began in September 2000. The DOZ Mine will reach its design production rate of 25 kt/d (27,500 stpd) in 2003. A study is under way to determine if an ultimate production rate of 35 kt/d (38,500 stpd) is feasible.

Jan 1, 2001

By B. T. Lusk, Q. Q. Huang, R. Q. Honaker, K. A. Perry

Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. It is applied either dry or wet. Both methods have advantages and disadvantages, but the formation of caked rock dust particles is cited as a significant concern for wet applications. We conducted a study to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid and sodium oleate. At a sodium oleate dosage of 1 kg/t, a contact angle of 112o was measured, indicating strong surface hydrophobicity and thus the ability to repel water. Fourier transform infrared spectroscopy (FTIR) studies indicated a chemisorption mechanism, which is necessary for long-term stability of the surface modification. The dispersibility of the modified rock dust samples was elevated by the application of both oleic acid and sodium oleate, thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed an 82.8 percent reduction in the dust explosion potential relative to untreated rock test applied by the wet technique.

Jan 1, 2015

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By J. E. Urosek

In October, 1990, a fire started in a large underground coal mine in Western Pennsylvania. During fire-fighting activities, an explosion occurred and all personnel were evacuated. Safe re-entry into the mine was not possible and the mine was sealed. Recovery efforts began in January, 1991 and continued until March, 1991, when permanent underground seals were installed between the fire area and the mine openings. This paper describes an extensive atmospheric monitoring program conducted by the Mine Safety and Health Administration (MSHA), Pittsburgh Safety and Health Technology Center (PS&HTC) including the analysis of mine fire gases, natural ventilation, fan pressure and air quantity distribution.

Jan 1, 1993

By R. S. Ondrey

MSHA has prepared two pamphlets that provide guidelines for selecting dust control parameters for underground coal mining sections. These guidelines are based on research conducted by the Bureau of Mines and underground studies conducted by MSHA. One set of guidelines is specific for longwall mining operations. Another set of guidelines covers room-and-pillar operations. The guidelines contain a general discussion on the appropriate use of ventilation and water to optimize the control of dust.

Jan 1, 1995

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By X. Cheng

The mechanism of cathodic decomposition of pyrrhotite was studied in deoxygenated solutions at natural, near neutral pH using potential and cyclic voltammetric measurements. Reaction products on pyrrhotite surfaces were examined by AES and XPS, and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by micro-flotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1993

By D. M. Larsen

Since start-up in 1985 the Cannon Mine has produced and shipped a 170 g Au/tonne (5 oz Au/ton) flotation concentrate to various smelters for gold and silver recovery. Several processed have been investigated to economically produce dore' at the mine site from the refractory concentrate. This paper describes recent laboratory and pilot scale test work utilized in the process design and engineering feasibility study of a 73 tonne/day (80 ton/day) pressure oxidation and CIL facility. The designed pressure oxidation circuit utilizes a series of vertical autoclave units operating at 170°C (338"F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1993

By T. R. Ellis

Regulation of mineral property valuation methodology by governments and others is due to frauds, condemnation and takings, banking industry problems, and litigation. Definitions of "reserves," "resources," and "qualified person" continue to evolve, along with guidelines to the data and disclosure required to support valuations. A less recognized but vital issue relates to the regulatory acceptability of alternatives to the comparable sales method. Comparable sales generally work well for surface real estate, and sometimes for precious metal deposits, but not at all for most industrial mineral properties. Alternative methods, such as net present value, or a geoscience rating system, often provide better valuations. Yet US regulations dictate comparable sales as the preferred method. The task of convincing regulators of the inapplicability of comparable sales to mineral properties, particularly those lacking reserves, may be as important as the valuation itself.

Jan 1, 1999

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Patrick Maier, Gregory E. Bogin Jr

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. As a result, the severity of mine explosions ranges from minor damage to loss of lives and permanent mine closure. Experimental results have shown that the inclusion of obstacles can significantly increase the flame propagation velocity by inducing turbulence. This research focuses on explosion experiments in a 71 cm diameter, 30.5 m long reactor that includes rock piles as obstacles along with developing the corresponding CFD model that captures the observed flame behavior and interaction with the obstacles. The rock rubble increases the flame front propagation velocity by 500% compared to the maximum velocity observed in the empty reactor experiments. The 2D and 3D CFD models predict the experimental flame front propagation velocity, whereas the 3D model shows a more explicit conformity than the 2D model. Although the computational time to complete the simulation is much less for the 2D model than for the 3D model, the 2D model is not sufficient to simulate cases with rock rubble since it cannot capture the propagation of the flame through the small voids between the rocks with the same effective blockage ratio as the 3D model. The validated CFD model can be scaled up to simulate methane explosions in full scale mine and industrial settings.

Nov 20, 2023

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Significant strides have been made in optimizing the design of filtration and pressurization systems used on the enclosed cabs of mobile mining equipment to reduce respirable dust and provide the best air quality to the equipment operators. Considering all of the advances made in this area, one aspect that still needed to be evaluated was a comparison of the efficiencies of the different filters used in these systems. As high-efficiency particulate arrestance (HEPA) filters provide the highest filtering efficiency, the general assumption would be that they would also provide the greatest level of protection to workers. Researchers for the U.S. National Institute for Occupational Safety and Health (NIOSH) speculated, based upon a previous laboratory study, that filters with minimum efficiency reporting value, or MERV rating, of 16 may be a more appropriate choice than HEPA filters in most cases for the mining industry. A study was therefore performed comparing HEPA and MERV 16 filters on two kinds of underground limestone mining equipment, a roof bolter and a face drill, to evaluate this theory. Testing showed that, at the 95-percent confidence level, there was no statistical difference between the efficiencies of the two types of filters on the two kinds of mining equipment. As the MERV 16 filters were less restrictive, provided greater airflow and cab pressurization, cost less and required less-frequent replacement than the HEPA filters, the MERV 16 filters were concluded to be the optimal choice for both the roof bolter and the face drill in this comparative analysis case study. Another key finding of this study is the substantial improvement in the effectiveness of filtration and pressurization systems when using a final filter design.

Aug 1, 2016

By William D. Mayercheck

Beginning in 1974, the Bureau of Mines, U.S. Department of the Interior, sponsored R & D efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The U.S. Department of Energy continued this effort as of October 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems or components now being built, surface tested, or tried underground.

Jan 1, 1981

By Carl E. Williams

During the past two years a computer program called "COPOR," Computerized Open Pit Optimization Routine, has been developed and used for mine planning of several base metal deposits. This routine utilizes a three dimensional computerized block model of an orebody, some economic parameters and operating constraints to locate the mineable or economic limits of the deposit schedule the yearly production from the mine and produce bench by bench ore reserve summaries and maps of the yearly and ultimate pit configurations. The moving cone method is used to perform these functions with a conventional block model. This model is conventional in the sense that each block is assumed to be homogenous; i.e., either ore or waste but not a mixture of the two. Due to the nature of a seam type deposit this approach is not realistic; therefore, revisions have been made to form a new version of the COPOR program. This version has been named "COALOR," Coal Optimization Routine. COALOR contains all of the power of the COPOR program but is equipped to handle the intricacies of coal seam type deposits. The deposit can be composed of a single seam or multiple seams which are horizontal or dipping at any angle. The numerous coal quality values can be incorporated to aid the optimization of the economic pit limits and yearly scheduling.

Jan 1, 1978

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By Adrian C. Dorenfeld

Concentradora "Dana Aida" (100 t/d capacity) was built in 1971-1972 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals from two veins. The veins, Don Felipe and aria are about 150 m apart, but are distinctly different mineralogically. The deposit is near San Juan de Guadalupe, Durango. Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuila. Sampling, ore testing, flowsheet design, plant design, drawings purchasing, financing, etc. was planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1979

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

The depletion of good-quality phosphate resources, coupled by a need to supply acceptable products at a rapid rate, while meeting the specifications of fertilizer chemical plants, is of significant concern to the phosphate industry, particularly the production of concentrates with tolerable dolomite content. Tremendous efforts have been made in the past to develop an efficient and economical process that can effectively reject dolomite. However, dolomite removal continues to plague the phosphate industry due to several process-specific challenges being encountered with various beneficiation technologies. In this regard, detailed characterization of phosphate reserves is crucial to understand textural limitations and help design appropriate strategies to achieve quality products. In this paper, the development of procedures to establish dolomite rejection/francolite recovery curves for gravity preconcentration of pebble phosphate from Central Florida is described using high-speed X-ray computed tomography (HSXCT). The developed procedure is illustrated with the analysis of high MgO pebble phosphate samples (10.39 mm × 1 mm) received from South Pasture and Four Corners locations operated by the Mosaic company. The rejection/recovery curves were calculated for each sample for five different particle size classes to observe the trend in rejection/recovery with variation in particle size. In order to evaluate the reliability of the HSXCT data, analysis using the high-resolution X-ray computed tomography (HRXCT) technique was performed on one particular sample (FC-3-1). Finally, to assess the separation efficiency, the HSXCT and HRXCT rejection/recovery curves obtained were compared to experimental gravity preconcentration results reported in the literature. In this way, liberation limitations for gravity preconcentration in the processing of pebble phosphate have been established based on X-ray computed tomography analysis.

By K. Witt, S. Steinlechner

In different nonferrous metal-producing industry sectors, the impurity element iron has to be removed from the process solution. Examples for the arising residues are jarosite or goethite precipitates from nickel or zinc production but also red mud from aluminum production. Regardless of environmental concerns, the material is landfilled in almost any case, although valuables such as indium, silver, nickel, or zinc are present in considerable amounts. Within the presented research, a low carbon dioxide emitting multi-metal recovery from such iron-containing residues by means of a selective chlorination extraction has been fundamentally evaluated by experiments but also by comprehensive thermodynamic calculations. The paper summarizes the thermodynamic fundamental concept exploited to separate the dominating iron matrix from the valuable elements and shows verification experiments in a lab size of several grams. Through thermodynamic calculations and smallscale experiments with pure metal oxides and sulfates, it has been proven that the metal chlorides AlCl3∙ 6H2O, FeCl3∙ 6H2O, and MgCl2∙ 6H2O are viable and effective reactants for chlorination. In trials with actual industrial iron precipitation residues from the zinc industry, especially, the use of MgCl2∙ 6H2O and FeCl3∙ 6H2O leads to high extraction rates for the investigated valuable metals Ag, Au, Bi, Cu, In, Pb, Sn, and Zn.

Nov 14, 2023

By Will B. Jamison

The most serious safety problems encountered in U. S. underground coal mines today are related to the roof bolting operation. Also, roof bolting is usually the operation which limits coal production of the section. The purpose of my paper is to review some of the research, developments, and new ideas related to roof bolting. Many of these ideas have originated at. coal mines or with manufacturers. Most of the research on fundamental improvements has been funded by, and is a part of, the excellent and broad plans of the Bureau of Mines.

Jan 1, 1977

By H. P. Cole

A team of researchers at the University of Kentucky, working under a USBM contract, developed over 65 simulation exercises for teaching and testing problem-solving and decision-making skills to miners and mining engineers. These skills involve both improving judgment and decision making in mine emergencies and enhancing the learning of real-world engineering design principles. The exercises are ideally suited for either latent image format or for computer-aided instruction. Exercise features are summarized, the structure and field testing of typical exercises described, and sample frames of individual exercises presented. Empirical data are summarized that describe the effectiveness of using these short, time-efficient performance tasks that simulate real problems and that provide immediate corrective feedback for teaching and testing critical skills. I

Jan 1, 1991