Search Documents

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

By N. N. Clark, C. M. Atkinson

Pachuca tanks are used widely in the mineral industry for leaching and mixing operations. An analysis has been presented previously to predict circulation of homogenous slurry in Pachuca tanks with full height draft tubes. However, settling of solids causes deviation from the homogenous case. Circulation of settling slurry in a Pachuca tank is modeled and shown to be a function of settling velocity, solids fraction, solid and liquid density, air flew rate, and tank dimensions. The pressure balance is shown to be very sensitive to these parameters, especially at low slurry velocities. Equations for predicting the air requirements in Pachuca tanks containing settling solids are presented.

Jan 1, 1988

By Lester G. Rollins

Coal today enjoys a dominant position, serving the energy and metallurgical marketed The measure of success in the market place is, and will continue to be, the price per million BTUs or price per ton delivered to the user. The Coal Industry's remarkable record of price stability since World War II is well known. The next twenty years promise to be equally as challenging. This challenge will be met our president, Mr. Drain, has often stated that, ?The Joy Manufacturing Company is betting that coal will meet the challenge.? To this end, the resources of Joy have been committed to doing its part. Joy's efforts are directed toward a target which has been defined as: 1. Deliver coal to the user at a price of $.15/MBTU or less. or; 2. Deliver coal to the mine portal at a cost of $1.00 or less.

Jan 1, 1966

By James W. Harrower, Gerald S. Ball

This paper discusses the installation of steel linings in vertical, raisebored openings. Design criteria used to evaluate the applicability of liner type and design are presented as well as a brief description of installation procedures. Specific projects completed by J. S. Redpath Corporation are then outlined noting special considerations and techniques.

Jan 1, 1985

By R. R. Klimpel

The process of flotation is an extremely important solids separation technique employed in a wide variety of industrial process applications. Froth flotation is practiced in the coal industry to recover fines produced during the mining and cleaning of coal. A recent review article by Aplan (1) covers the processing variables encountered in the flotation of coal and the variety of chemicals and operating conditions which affect recovery. Numerous engineering and scientific studies have been performed with the goal of providing semifundamental laws of flotation behavior for improved screening of flotation chemicals, better equipment scale-up factors, etc. Often the results of such work are expressed in the form of mathematical models (e.g. 2, 3, 4, 5, 6) which are potentially useful for evaluating (simulating) on paper such alternatives as possibles process operating or configuration changes, the effects of ore and reagent changes, etc. It appears to be commonly accepted that a complete scientific/engineering characterization of flotation is immensely complicated and not sufficiently developed at the present to accurately predict (or understand) many important industrial facets of flotation. Thus, one is often reduced to detailed experimental characterization in both the laboratory and plant in order to fully evaluate flotation changes or alternatives. It is the purpose of this paper to describe a method of batch laboratory data characterization that is useful in evaluating flotation chemical reagents including froth flotation of coal. The approach consists of running a series of time-recovery curves in a batch float cell followed by the computer curve fitting of this data to a series of mathematical models based on semi-physical reasoning. The unknowns or parameters of these models are then optimally chosen so as to best fit the experimental data. It has been found in both coal and mineral systems that changes in reagent type, concentration, system pH, grind, etc. cause very consistent and logical changes to

Jan 1, 1979

By W. T. Walter

High-G centrifuges from five preparation plants were sampled to determine and quantify the various operating factors affecting performance. The operating factors that were considered include feed rate and percent solids, size of feed material, screen-basket type, hardness of coal and age of the flights. The performance parameters that were measured include product surface moisture, recovery and degradation of the coal. Regression equations with good significance levels were developed.

Jan 1, 1982

By J. Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulphide concentrate which must be treated either by roasting, biooxidation or by pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process and has the inherent advantage of meeting the stringent environmental regulations in the province of Ontario. A comparison of biooxidation and pressure oxidation was completed early in 1990 and the latter was selected by Placer Dome as the preferred process for replacement of the roasters. The commercial plant design was based on technology supplied by Sherritt Gordon and in July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The following summary describes the start up of the new facility and presents typical operating data.

Jan 1, 1992

As metal prices fluctuated over the years, so too have the fortunes of many of those mining in Canada?s Yukon province. With a rich mining history that dates back to the Klondike gold rush of 1896 to 1898 and continues to thrive today, Yukon has experienced several ?boom-and-bust? cycles. However, during the world?s most recent mining ?bust? Yukon has held strong and has re-mained one of the world?s hottest destinations for mineral exploration. In fact, the area even exceeded forecasts in 2009, more than doubling last year. And the near-future looks just as bright.

Jan 1, 2010

By Terry W. Engelhart

"A computer-based approach to online supervisory control and operations management of bulk materials handling terminals". This paper describes an integrated computer facility supporting the functions and responsibilities of shift operations, scheduling, maintenance and management using real-time interactive techniques. The functions and responsibilities as related to coal export terminals are specifically addressed, although these functions would be equally applicable to other terminal configurations and other commodities. A discussion of the resulting benefits are presented: - throughput efficiency - long-term planning and scheduling, using simulation - operations monitoring and protection - demurrage/despatch optimization - preventative maintenance - operational productivity

Jan 1, 1982

By P. Mousset-Jones, G. Danko

Rock thermophysical properties, i.e. heat conductivity and thermal diffusivity, were obtained for reference values at the Waldo Test Mine for mine fire simulation purposes. An in situ measurement method was chosen since it could include the effect of rock fractures. The REKA method (Rapid Evaluation of k and alpha) was used because it can measure conductivity (k) and diffusivity (alpha) simultaneously within an eight-hour measurement period. A total of six measurements were taken in three different holes, and at two different depths from the collar of the hole. Each measurement provided an averaged conductivity and diffusivity for a volume of rock of approximately one cubic meter. The boreholes were driven into the upper and lower limestone, two at right angles to and one parallel to, the stratification of the rock. Significant representative conductivity and diffusivity values were obtained for the whole mine by averaging the six measurement results. The thermal properties for the band of shale in between the two limestones were not measured in situ, but only in the laboratory. Problems were encountered in the evaluation because of unexpected heat conduction on one side of the symmetrically built probe. A modification was made to the previously developed evaluation method together with further testing and correction, before the final results were obtained. As expected, the in situ and lab- oratory measured values of k and alpha compared favorably, since the in situ rock was dry and relatively unstressed.

Jan 1, 1989

By Richard H. De Voto

The McDonald gold project and two satellite gold deposits near Lincoln, MT were discovered in the early 1990s. They contain at least 307.9 t (9.9 million oz) of gold and 933 t (30 million oz)of silver. The McDonald gold deposit alone contains 223.9 t (7.2 million oz) of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $6.10/g ($190/oz). The deposit is predominantly oxidized with no chance of acid production. It can be mined, operated and reclaimed with minimal permanent environmental disturbance other than the creation of an open-pit filled with a fresh-water lake that would support trout.

Jan 1, 2000

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976

By Ralph M. Barnett

It is no longer a question of "If" mining operations will meet standards and regulations set by various governing bodies and the demands of citizen groups. Legislation is fact. The needs of citizens are becoming more of a integral part of mining company planning. "Open Planning", regardless of some frustrations it provides, is working. Climax, AMAX Chemical and AMAX Exploration are successfully employing several citizen involvement techniques in exploration and feasibility study phases of planning for potential new mines.

Jan 1, 1978

The 21st Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Sheraton Tucson Hotel in Tucson, AZ on Saturday, Dec. 6, 2003. This year’s inductee, guest of honor and featured speaker at the banquet will be Thomas J. O’Neil, recently retired president and chief operating officer of Cleveland Cliffs Mining. Prior to Cliffs, O’Neil spent 10 years with Cyprus Minerals. He was also professor and head of the Department of Mining and Geological Engineering at the University of Arizona. As representatives of mining heritage, the Hall of Fame will induct James Boyd and Thomas F. Walsh. Walsh discovered a rich gold telluride vein in Ouray, CO, which became the Camp Bird gold mine. Boyd was a former director of the U.S. Bureau of Mines, vice president of Kennecott Copper and later president of Copper Range.

Jan 1, 2003

By Ben Sosewitz

The subject of rapid excavation tunneling is one that is extremely important to the people in the Metropolitan area of Chicago. My personal observation is that it is also extremely important to the urban communities around the U.S., to many local and state governments, and to the public officials who are deeply concerned about state affairs and taxes. The Metropolitan Chicago area is in fact, (as are 40 other major urban areas in the U.S.) confronted at the present time with a very serious combined sewer overflow, drainage and pollution problem which accounts for an estimated 40% of the pollutional load on its waterway system. In response to this the District has to date spent some seven millions of dollars in an attempt to find the most economical solution available for the elimination of this problem. This study included extensive investigations of the geological strata, the quantity and quality of storm runoff to be dealt with, and the various methods of storage and treatment available. It has considered solving the overflow problem by a concept involving a series of tunnels, rock tunnels, shafts and storage areas which will collect, retain and subsequently treat that portion of the combined sewer overflow which can be handled in the most cost-effective and economical way, consistent with following the federal and state standards - with which we at the present time agree in principle.

Jan 1, 1997

By J. B. Griffiths

Clearly there is a tremendous need for assistance in Eastern Europe since most industries must undergo major restructuring. The new governments face many dilemmas, the first task being to establish an order of priorities to deal with the numerous problems at hand. Issues such as the standard of living take low priority compared with market economy and ecological problems. The concept of a Comecon market is now virtually non-existent and trade in roubles ceased from 1991. From this time onwards countries were obliged to trade using free market prices. Governments must also avoid the economic mistakes of countries such as Poland with its high devaluation and lack of economic control and, if possible, contain inflation and unemployment. The privatization of Eastern European enterprises raises considerable difficulties, particularly for large corporations, employing anywhere from 50-100,000 people, which played a major role in the national economy. Whichever method is selected, however, still has to overcome the problem of lack of capital and evaluating the national property. For example, earnings represent only a small percentage of the value of these national industries and thus cannot convert to private ownership without foreign capital investment, either direct or as joint venture capital.

Jan 1, 1992

By Ralph B. Hall

Examination of cored material from the Southern Extension of the Florida Phosphate District has indicated a decidedly complex and diverse sequence of phosphatic sedimentary units. The perfunctory logging techniques formerly used in the Central District are inadequate to properly describe the intricate geology of these sediments. Adequate geologic training and familiarity with the potential ramifications of his judgement are a necessity for the logging geologist. A combination descriptive-graphic logging model is proposed that utilizes a standardized sediment nomenclature system and descriptive symbols for type materials commonly found in these sediments. Justification for adoption of this or a similar logging model is discussed.

Jan 1, 1983

By L. P. Meade

The need to feed an established talc mill from a crude are source located closer to the mill prompted the drilling in 1986 of a previously mapped talc-carbonate deposit. This talc-bearing rock had never been considered as a potential source of crude talc are because of the high carbonate content and other deleterious minerals that were observed in outcrops. Selective mining, in-pit grade control and creative processing has allowed this deposit to be developed into an orebody. By definition, an orebody has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by are tenor.

Jan 1, 1992

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958