Search Documents

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in intensified efforts in inspections of coal refuse sites by the Mining. Enforcement, and Safety Administration (MESA). MESA inspections however, are mainly qualitative and are often time consuming, Therefore, in August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in MESA inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photo interpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Based on CH2M HILL results cost for monitoring by rapid system was approximately 25 percent of cost by conventional ground survey.

Jan 1, 1980

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines is completing a Feasibility Study for a new open pit gold mine in north central NV. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing open pit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled, and unscheduled random events during the period under analysis.

Jan 1, 2006

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By Todd S. Harris

Industrial minerals or non-metallic minerals are loosely used terms applied to a diverse assortment of materials which, in many cases, have nothing more in common other than the fact that they are neither metals nor fuel minerals. To help bring order to this otherwise random assortment of minerals, we have grouped these materials into two main categories; chemical and physical minerals, and nine sub-categories based on end-use applications as shown in Table 1. Chemical minerals are products which are principally used for the specific chemical elements they contain, whereas physical minerals are products which are used to meet specific performance specifications. The latter part of the 1970?s, in particular 1978, were considered peak years in terms of production and sales for many industries, By using 1978 as a base year, we can evaluate wherethese markets stand today after the recession of the early 1980's and the recovery which began several years ago. From this historical overview and appraisal of the current situation, various assumptions can be drawn as to which markets are expected to perform well into the 1990's.

Jan 1, 1987

By Carl F. Austin

The subject of strata control in mining can be approached from both static or loading concepts or from dynamic or impulsive loading concepts. The fracture process itself appears to be primarily a dynamic process as is the gross creation of fractures through the use of impact, stress wave passage or in more general terms, the use of explosives. This paper presents experimental results which indicate that the understanding of the fracture behavior of rock that has been, established in the open literature is not always appropriate. In particular, the results of this experimental program have shown very interesting differences between the formation of fractures in rock and the formation of fractures in other materials such as metals and plastics which are often used as models for rock behavior studies Fracture patterns and causes of dynamic fracturing in various rock and artificial materials are presented.

Jan 1, 1965

By R. J. Roman

Several research groups have spent considerable time investigating coarse ore leaching. Coarse ore leaching includes both heap and dump leaching. The term "heap leaching" will be used in this paper to mean any type of coarse ore leaching. The results of their work are generally in agreement: the progress of leaching can be described by the shrinking core model and its associated mathematics. The shrinking core model is schematically represented in Figure 1. The particle is contacted by the leach solution on its outside surface and the solution migrates inward by filling the pores on the particle. As the solution filling the pores comes in contact with grains of ore mineral the reagent chemically reacts with the ore mineral to solubilize the contained metal. The solubilized metal diffuses outward to the particle surface and is washed away by the leach solution flowing past the particle. The leaching reagent in the particle interior is replenished by the diffusion of reagent from the surface of the particle to the interior of the particle. If the chemical reaction between the leaching reagent and the ore mineral is relatively fast compared to the diffusion rate of the reagent in the solution in the pores of the particle then leaching proceeds from the outside of the particle inward resulting in a "shrinking core" of unreacted ore surrounded by a "leached shell". The rate controlling step in the reaction can initially be a chemical reaction between the reagent and the ore mineral grain, however, once the reaction has proceeded a short period of time diffusion of the leaching reagent through the leached shell will be the slow step and hence the rate controlling step in the production of metal from an ore particle.

Jan 1, 1992

By E Marambio, R Brändle, G Fischer, G von Rickenbach, M Fuentealba, L Burgos, R Luis Fonseca

In underground excavations, under high stress conditions, ground support systems must provide safe and effective response to dynamic events. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the back analysis through numerical methods (central difference and Newmark’s method) of a ground support system tested with a double dynamic impact in 2019 is presented.

Apr 26, 2022

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By Keith A. Heasley

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence. Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents several case studies where a mechanics-based, boundary-element program is used to back-calculate the surface subsidence associated with various panels at several Northern Appalachian coal mines. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin scam or vein type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from the case studies in this paper demonstrate that the laminated model with calibrated properties can easily provide moderately accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies arc recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

Jan 1, 1999

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 degrees apart into the outer surface of a hollow cylindrical steel tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U. S. patent (3,914,992) assigned by the author to the Department of the Interior was granted October 28, 1975.

Jan 1, 1976

By M. Canty

Results are presented that were gathered during pilot-and field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE, Technology Applications, Inc., located in Butte, Montana. Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides; the bicarbonate serves to help neutralized the drainage. Pilot-scale testing was performed within eight packed-bed reactors at a temperature representative of a field application of this technology in a northern climate, nominally 8°C. The reactors, packed with an organic substrate, were operated continuously in upflow configurations receiving AMD at a flow rate corresponding to a 5-day retention time over a test duration of 60 days. During this time, numerous physical and chemical parameters were monitored. Pilot-scale metal removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium, and 96% for copper. Iron and arsenic removal was not as effective as the aforementioned metals, which was largely attributed to the high levels of iron and arsenic contaminating the organic substrate. Evidence existed that both adsorption and sulfate reduction were occurring within the reactors.

Jan 1, 1998

By J. A. Rusnak, M. M. Gadde, S. S. Peng

In situ stresses are one of the key inputs to a successful underground excavation design. Because of the complex mechanisms involved in arriving at the current state of stress at a point in the Earth’s crust, often the only reliable way of estimating in situ stresses is by actual measurement. In the United States coal mines, overcoring relief method is by far the most popular technique used for estimating the virgin stress field. Typically, for stress measurement with overcoring, a vertical borehole is drilled into the roof or floor of an underground coal mine opening to a certain distance and change in borehole diameter is monitored at multiple points along the length of the hole when this borehole is overcored. For the measured stresses to represent the pre-mining stress field, the measurement points should be located beyond the influence zone of the mine opening. Actual data from several US coal mines have been collected to check if the measured stresses by overcoring represent true in situ stresses. The data indicate that most of the stress measurements were within the excavation influence zone. A three-dimensional numerical modeling methodology was applied to one of the collected cases to correct the measured stresses for the excavation influence. The modeling approach demonstrated the usefulness of integrating numerical modeling into a stress measurement program to estimate ‘true’ in situ stresses.

Jan 1, 2006

By Betty Gibbs

The Ore Body Modeling and Mine Planning Worshop, sponsored by the Society for Mining, Metallurgy, and Exploration, Inc. (SME), was held Feb. 22-24, 1991 before the SME Annual Meeting and Exhibit in Denver, CO. More than 40 people from mining companies, government agencies and universities attended. Eight vendors of integrated ore body modeling and mine planning software attended and presented the results of problem sets given before and during the workshop. They were: [ ]

Jan 1, 1991

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator's training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

This paper describes the vibration transmissibility characteristics of mining vehicle seats under dynamic conditions in an opencast iron ore mine. Magnitude and frequency contents of vibration signals on the seat floor as well as on top of the seats were measured to record the change during transmission. The conventional rigid seats were found to resonate at about 4 Hz, which coincides with the resonance of the human spine. The pneumatic suspension seats also proved to be more efficient in attenuating the overall vibration energy transmitted from the vehicle chassis to the human body.

By Georgene Renner, Chee Theng, William Gleason

"A walk through the exhibit hall or a glance at the technical programing that was offered at the 2019 SME Annual Conference & Expo and CMA 121st National Western Mining Conference in Denver, CO, Feb. 24-27 makes it evident that the mining industry is an innovative one that is on the cutting edge of technology. However, a glance at the nearly 6,700 attendees of the conference and it is also evident that while the industry is moving forward at a rapid pace in some areas, it is lagging behind in terms of diversity, both in gender and ethnicity.At Monday morning’s keynote session, Hannah Ubi, a millennial and a public speaker who joked that she is the proud owner of a sixth-place swimming trophy and a number of participation medals, addressed a full house that consisted of many men with gray hair or balding heads. The issue of an aging workforce that is rapidly being depleted by retirements is not a new one for the mining industry. In fact, it has been a concern for the industry for more than a decade. The central question has long been, “when the current senior-level people begin to retire, how do we replace them, and how do we fill the knowledge gap that is walking off into the sunset?” SME has been on the front lines in searching for solutions to the impending problem and, along with industry partners, has worked hard to develop programs that will address these issues. Among other efforts, the Society has developed a Ph.D. fellowship program to encourage people to remain in academia to teach the next generation and to help train the next generation to take over in the private sector.“The SME Foundation’s Ph.D. and Career Development Grant program is exceeding expectations at this point with two Ph.D. students graduating and taking a position in academia and two professors achieving tenure,” SME Executive Director Dave Kanagy said during the conference.The Society’s Minerals Education Coalition (MEC) has done its part to help educate future generations about the mining industry with initiatives like EngineerGirl, the Boy Scout Merit Badge and Move Mining, the Shark-Tank-style competition that was held on Monday with five finalists competing for the top prize (ME, April 2019, page 53)."

May 1, 2019

By D. L. Stevens

Following an in-depth scenario and strategic-planning exercise in 1997, Noranda's mine production goal was set at 500 kt/a (550,000 stpy) of both copper and zinc metal in five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in Noranda's program. The following steps were taken: the exploration and business development groups were combined, teams were formed to search for and respond to opportunity; geologists were coached to become more business minded and engineers were coached to become more optimistic; the company went global; clear thresholds were set, marginal properties were farmed out and other properties were fast tracked; reconnaissance exploration was focussed where there was a clear competitive advantage; and Noranda became a "flexible" partner to juniors and seniors. Is it working? A number of successes, near successes and outright failures are discussed. The main result is a much higher rate of opportunity flux, which is essential for success in the mining industry.

Jan 1, 2000