Search Documents

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite 'dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By David Smith, Bernie Martin

The Queens Bored Tunnels consist of 11,000 feet of 19'-6" inside diameter tunnels mined through rock, mixed face and dense glacial till, constructed with bolted gasketed one pass reinforced concrete liner. The tunnels are to be excavated with a pressurized face TBM, either EPB or slurry. The construction of the tunnels will require ground stabilization in the mixed face area, instrumentation and monitoring of railway infrastructure, underpinning of bridges, relocation and protection of utilities, demolition of some industrial buildings, construction of open-cut approach tunnels and emergency exits and vent plants. The purpose of this paper is to describe the scope of work, the suggested methodology and the proposed construction schedule.

Jan 1, 2005

By B. J. S. Sceresini

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentra­tion and high pressure to achieve extremely rapid gold dissolu­tion rates. This is made possible without suffering from high energy or wear rates by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device which can be constructed from a variety of wear and chemical resistant materials. High temperature tolerance is also possible so that the device can be incorporated into a pressure leach circuit with significant capital cost savings because of the high capacity to volume ratio that is an inherent feature of the device. For cyanidation applications the outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of about 150 dry tonnes per hour at 40-45 % solids. Service life at this throughput is at least three months. Six mines are currently employing the Filblast Process and another six are conducting plant trials. The ore types range from highly reactive, almost impossible to treat, pyrrhotite/ arsenopy­rite to deeply weathered clay ore which forms a highly viscous pulp. It has been found that the effect of shear thinning has resulted in improved leaching and adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately eight million tonnes per annum. This paper presents the operating benefits and cost savings which have been achieved in four plants, two treating oxide/ sulphide ore blends and two treating highly reactive sulphide ore and concentrate. Filblast leasing and maintenance charges and pump operating costs are about ten percent of the benefits. A conceptual cyanidation circuit based on the Filblast Cyanidation Process is also discussed. The Filblast System is an in-line pressure leach aerator/ reactor which generates very high shear and greatly enhances mass transfer rate by generating extremely small gas particles where oxygen gas is required for oxidation reactions and/or utilising the high shear characteristics to minimise the diffusion boundary layer. Both of these rate limiting factors effect the rate mechanism for gold cyanidation. Initially two multi-stage Filblast aerator cartridges formed a leach train but now the trend is to install a single submersible cartridge of equivalent perfor­mance. This design simplifies installation and minimises change-out times. However the in-line concept can be employed where high pressure leaching or pressure oxidation is required. The reactor is submerged in the leach tank so that the mass of gas micro-bubbles contained in the discharging slurry is entrained in the agitator vortex and is thoroughly dispersed throughout the tank. A diagrammatic representation of a leaching circuit incorpo­rating the Filblast Reactor is shown in Figure 1. The recirculation pump takes new feed directly from the cyclone overflow trash screen either under gravity or pump fed and recirculates the balance to maintain 250 - 270 m3/h total slurry flow. All of the leach feed slurry gets at least one pass through the Filblast thereby eliminating short-circuiting. Typically a 6/4 EAH Warman pump drawing 60-70 kW is required to circulate 250 m3/h through the system. The back pressure generated by the Filblast is in the range of 400-500 kPa depending upon pumping rate, pulp density and slurry rheology. The high shearing rate effectively negates the viscous effect of slurries and the addition of a gas further reduces the pulp density by virtue of the intensely aerated, homogeneous medium. The gold leaching Filblast cartridge elements are made of polyurethane but stainless steel, ni-hard, rubber or ceramics can be used depending on the operating temperature and design duty. The efficiency of the Filblast Leach Reactor in gold cyani­dation is due to the extremely efficient mixing, oxygen dissolu­tion and surface polishing action of the Filblast design. Either air or oxygen may be used but Atomaer recommend the use of oxygen because of the rate benefits gained from cyaniding at [02] significantly > 20 ppm D O in the reactor. Very high DO concentrations have been measured; in excess of 50 ppm. There is some debate as to whether the value is a true measure of the DO or the oxygen meter sensor is measuring the effect of a mass of very fine bubbles of free oxygen. Regardless of the fact the reactor has registered some amazing gold dissolution rates commonly in excess of 80 % during transit of the pulp through the reactor. The elapsed time is less than half a second!

Jan 1, 1995

By M. Valdebenito, J. Rajala

An OCS Expert control system was implemented by Svedala Cisa at the Minera Maricunga Refugio Crush-Leach Operation near Copiapo, Chile. The purpose of the Expert system was to maximize production through the primary and secondary crushing circuits and help balance crusher usage between each stage to maximize total plant production. Interesting aspects of the control strategies are discussed. Benefits of the control were verified through a randomized On/Off test program. Tonnage increases ranged from 5% to approximately 20% at good confidence intervals. Benefits analysis results are discussed. The crushing plant at Refugio is very remote and is located at approximately 15,500 ft. This poses many challenges. The effect of altitude and remote location on plant operation are discussed.

Jan 1, 2002

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By Z. Hladysz

It is common to nine a coal seam affected by previous extraction of a coal seam below. As a result of that severe problems may occur during the extraction process. This paper presents the analysis of undermining effects based on field observations. A simplified method for the evaluation of risk in undermining operations is presented and predictions of the degree of possible damages to the undermined coal seam is given.

Jan 1, 1985

By D. Gove

Several coal mines in Southeastern United State face the problem of multiple, very thin coal seams or seams adhering to interburden, and because of the strip ratio economics, these seams must be recovered. Over the past few years several mines have discovered a common method to solving these problems...use of a Caterpillar RR-250 Road Reclaimer.

Jan 1, 1995

By P. Lausch, R. A. Mercer, J. F. Archibald

An innovative, polyurethane-based, spray on rock-lining material, designated Mineguard™ by its developers, is being manufactured to provide rapidly deployable area support coverage for specific use in underground hardrock mines. This form of surface-coating agent is intended to replace both shotcrete and the screen component of bolt-and-screen support systems. Due to the rapid rate of application, ease of installation and ability to achieve a 90% cure within seconds of application, Mineguard™ has considerable potential for use in mining and excavation operations that require a rapid rate of advance and a high degree of automation.

Jan 1, 1996

By S. Chander

A comparison of gold, platinum and sulfide ion selective electrodes was made for determination of Eh in solutions containing hydrosulfide ions as a model system. The comparison was made in terms of the accuracy of the measured response, response time, pH dependence, and reproducibility of measurement. The sensitivity of each electrode towards changes in hydrosulfide ion concentration was measured in terms of the change in measured Eh per decade change in concentration. On the basis of a detailed investigation of the electrode processes occurring at the surface of gold and platinum electrodes, it was postulated that within the pH range investigated these electrodes respond to changes in the hydrosulfide ion concentration in solution. In comparison, the sulfide ion selective electrode is known to respond to changes in the sulfide ion activity in solution. Although the potentials measured with gold and platinum electrodes were mixed potentials, pretreatment procedures can be used to obtain a signal suitable for process control. For control of hydrosulfide ions in flotation pulps, the use of a gold electrode pretreated at 1.0 V with respect to a standard hydrogen electrode is recommended.

Jan 1, 1992

By Wilfred Walker

Much is known of the geography of the Alpine orogeny because it has now ended and all geosynclines are in their terminal, cordilleran form. The principle of sea floor spreading, continental drift, and mantle cells has gained general acceptance, but the number and position of the cells, even during the Alpine orogeny, is controversial. The oceanographers have demonstrated the uprises and in this paper it is suggested that downflows are marked by island arcs in the oceans and geosynclines (now cordillera) in the continents, for a total of about a dozen cells. Major mineral deposits associated-with the Alpine downflows are porphyry copper, molybdenum, nickel, chrome, lead-zinc-silver, gold, mercury, tungsten, and tin. Amore precise environment is known for some of these metals, for example, nickel, chrome, and mercury in flysch (which flanks mantle downturns), Ten major orogenies have taken place from 3500 m.y. to the present, Their re¬construction and metallogenesis is the subject of a continuing study.

Jan 1, 1971

By Steve Kral

The domestic mining industry may be in the doldrums but there appears to be hope, at least from a regulatory standpoint. At least one US senator believes that the events of Sept. 11, 2001 made many citizens see the need for the country to become more self-reliant on its growing energy needs. Even before that tragic day, however, the Bush administration was making a strong push to open up more public land for energy and natural resource development.

Jan 1, 2002

By Ping Zhang, Xu Ma

Perturbations from mining operations significantly affect the stability of rock masses, especially with the increase in mining depths. This study uses the discrete element method (DEM) to investigate shear slip failure along discontinuities in an underground mine, aiming to quantify seismic moment and seismic energy to better understand seismic hazards.

May 1, 2023

By John A. Sievert

Sedimentary deposits contain an appreciable portion of the world's supply of uranium. Predictions of nuclear fuel usage in the United States indicate that these reserves will have to be tapped if the domestic industry is to be the major supplier of fuels for the nuclear reactors. Techniques developed within the petroleum industry are a base on which to build economically attractive fluid mining processes for the recovery of these uranium values. The problems central to the success of such mining processes are the containment, control, and recovery of a narrow band of pregnant leach solution as it progresses from the point of injection to the point of production Given sufficient incentive, suitable solutions to these problems can be found

Jan 1, 1970

By John Durkin

A system based on seismic techniques has been developed to detect and locate men trapped underground following a mine disaster. Both theoretical and field studies have been used to generate models to predict the performance of the system. For a strong source, it is almost certain that the miner's signal will be detected if the geophone array can be positioned over a likely area of entrapment. After signal processing, it is highly likely that the location of the miner can be determined within an accuracy of 100 ft (30.5 m). The system is presently operational in a state of readiness in the event of a mine disaster.

Jan 1, 1980

By Tim O’Neil

Caterpillar has introduced its 5090B front shovel, to work with 40 to 70 st (36 to 63 t) trucks. The new unit replaces Cat’s 5080 hydraulic excavator. The 5090B offers more engine horsepower, higher flow, greater digging forces, higher swing torque, faster swing speed and more drawbar pull than its predecessor. It can also handle larger bucket sizes than the previous model. These improvements enhance productivity and make the 5090B a high-volume material handler for hard rock and aggregates producers.

Jan 1, 2003

By Erich J. Jacob

In the past 15 years the enforced improvement of the public traffic systems caused a boom in urban tunnel construction. In 1961 the City of Paris started to build the Express-Metro. Of the 47 km long double-track line crossing the city center, nearly 45 km are in operation since 1971. Still missing is here only an about 2.6 km long connecting stretch, which is under construction now. From 1963 to 1969 the 21.8 km long Victoria Line was built in London as extension of the existing network,. A little later, in the years 1965 to 1973, the City of Hamburg supplemented its subway network by the construction of a 16.8 km long line between the Boroughs of Billstedt and Stellingen. Also in 1965 the City o Munich started to build a subway system of 54 km f length. Thereof a stretch of 16.2 km could be taken into operation in 1972 shortly before the Olympic Games. These are only some of the better known projectsas examples of the activities in European cities. In nearly all cities with more than about ½ million inhabitants subsurface traffic lines were begun or supplemented. Furthermore, numerous undercuts or other subsurface structures were built. The Ij Tunnel in Amsterdam and the new Elbe Tunnel in Hamburg may be mentioned, both structures finding international attention.

Jan 1, 1976