Search Documents

By Dennis Arthur Fenton

The hydrodynamic bearing was first described by, Reynolds in 1886, and has since been widely applied in motors, engines, compressors, hydroelectric turbines, and other machinery. For various reasons, the hydrostatic bearing currently predominates in the large, horizontal rotating machinery field (e.g. grinding mills). However, the current industry trend towards increasing size and energy efficiency has resulted in renewed interest in the advantages of hydrodynamic bearings. These advantages include structural improvements, reduced bearing friction, improved bearing life, improved transient characteristics, and reduced lubricant pump size and power requirements. In particular, the higher energy efficiency results in substantial savings on large machines. This paper describes some aspects of the design of large hydrodynamic bearings based on thirty years, of experience in the design of such bearings on grinding mills ranging in journal size from 2.1 m to 6.4 m, see Table 1.

Jan 1, 1985

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By J. Finch, J. Yianatos, N. W. Johnson, R. Espinosa-Gomez

A method of determining the maximum concentrate solids rate or carrying capacity is described for given column operating conditions. The method requires alteration of the feed rate of solids to the column at a fixed residence time by manipulation of the % solid of the column feed pulp or the bias rate. The carrying capacity was measured for five streams at the Mt. Isa Mines Pb/Zn and Cu concentrators. As a potential scale up parameter, the mass of solids per unit time per unit column cross section (Ca, g/min.cm2) is explored. Ca is tentatively related linearly to the 80% passing size (d80) of the concentrate. For d80 < 15 pm Ca was less than 4 g/min.cm2 (8 lb/min.ft2) which makes it a critical consideration in scale-up for such fine feeds. An alternative carrying capacity parameter, mass of solids per unit volume of gas Cg was not as useful as Ca since Cg varied inversely with gas rate.

Jan 1, 1988

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

The mineral industry uses significant amounts of water in processing. Thus, sustainable practices with the processing of ores are of critical importance. An impact tester was used to measure the adhesion force between particles and a glass disk [1,2]. A removal force was caused by the impact of the disk/particle containing a puck with a stopper. Johnson-Kendall-Roberts (JKR) theory [3] was used to determine the interfacial energy between the particles and the substrate. Capillary condensation of water can occur between the particle and surfaces in humid environments. The adhesion of particles on rough surfaces has been studied previously [4-10]. The research presented herein combines both variables to separate particle types with minimal water usage.

By K. Sasaki, H. Miyakoshi, K. Mashiba

A ventilation analytical system adapting nodal pressure method using skyline modified Choleski&apos;s decomposition scheme for network-flow analysis and a new practical system to estimate various thermal air conditions has been developed. The quasi-linear equations for solving steady-state network airflow have been described using the connective function in general forms. The skyline modified decomposition scheme has an advantage on rapid convergence and the sake of computer memory space com- pared with other schemes. The key part of the analysis for climatic conditions through network airways is how to estimate the temperature of the airway rock-surface with partly or full wet condition. A practical and simple solution without any iterative calculations for its estimation has been proposed. This new solution is applicable to practical ranges of airflow temperature, humidity, rock thermal properties and wetness. The present analytical sys- tem have been successfully applied to a ventilation simulator named "M1VENA"developed by authors.

Jan 1, 1996

By Robert H. Carpenter

Abstract, Syngenetic uranium in pre metamorphic Idaho Springs volcanics and sediments probably, was mobilized during metamorphism (1.7 b.y.) and partly retained along unconformities. Precambrian Silver Plume intrusives (1.4 b.y.) and Pikes Peak granite (1.0 b.y.) may have mobilized uranium from the craton and. Idaho Springs metamorphics to concentrate it in cauldron sites in migmatites, pegmatites, alaskite, disseminations and greissen. Tertiary intrusives also may have upgraded uranium by anatexis, leaching and differentiation. Tertiary vein and shear zone uranium mineralization may have-been-derived from underlying magma sources, leached from Idaho Springs metamorphics and from syngenetic leaching of overlying sediments and introduced by deep hydrothermal convection systems.

Jan 1, 1979

By J. G. Russell

The valuation of known mineral re-serves entails the economic evaluation of the mining enterprise and the valuation of other assets employed, including mining and processing plant and intangible assets. A case study approach analyzes two reserve situations: ownership of reserves (phosphate rock), and leasing of reserve lands (kaolin). The appraisal of the physical property is outlined, along with the economic analysis of the operation. The discounted net cash flow approach is used to value the enterprise, leading to value of the reserves after correlation with other assets employed.

Jan 1, 1989

By G. Le Bel

Discussion by G. Le Bel The paper proposes three methods to determine optimum lifetime of a mining project 1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project&apos;s potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: •It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. •The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate. Discount rate selection The opportunity cost of capital represents the rate of return that would be obtained if the capital was instead invested in other opportunities considered to exist. Such opportunities must be bypassed if the available capital is invested in the project studied 2. If these other opportunities carry risk similar to the project under analysis (for example, if they are other mining projects), there is no need to add incremental [ ] risk factors. On the other hand, if these opportunities are represented by the acquisition of government bonds yielding 7%, a risk premium factor must be included. The types of risks associated with a mining venture are shown in Table 1. Together they represent the "business risk" of being a mining company. The individual project risk is important to investors if it differs substantially from the business risk of the company and that of the other investments in mining ventures that we must pass up to invest in this particular project. A risk premium or discount would then be required. This can be illustrated by the following example. Consider that a company has two investment alternatives: one is the Cavender hypothetical project located in Nevada, and the other is the same project located in a civil war zone of central Europe. The second project requires a risk premium factor on the discount rate. Conversely, a project showing highly uncertain returns that are negatively correlated with the returns of the firm&apos;s other assets may decrease the company&apos;s corporate risk. Deterministic character of NPV calculation The cash flows used in NPV calculations are obtained from a set of variables. These variables are estimated using one parameter obtained from the engineering studies. Each parameter is thus a single value that is often termed a "realistic" or "best estimate" as opposed to "optimistic" or "pessimistic." However, considering that each variable can assume a range of values between the

Jan 1, 1994

By R. V. Stewart

This chrysotile asbestos orebody is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 mi) north of Montreal; 480 km (300 mi) north of the tree line and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1/4 mi) in length some 61 m (200 ft) in width and plunges at 25-30 below surface to a vertical depth of at least 610 m (2000 ft). The orebody was originally evaluated by programs of surface mapping, diamond drilling and bulk sampling. The fibre is semi-crude, possesses excellent strength, and good fibre length distribution.

Jan 1, 1978

By Harold E. Rowen

The listed title of my talk to-day is "MODERN ON STRAND SINTER COOLING". Perhaps it should he ve been "COMPLETION OF SINTERING ON THE STRAND" as the two are synonymous. By the very nature of the DWIGHT-LLOYD SINTERING PROCESS partial cooling on the strand is always present, but not completion of sintering and cooling on the strand. I have mentioned the Dwight-Lloyd process just to be certain the type of sintering under discussion is fully identified because some of the basic mechanisms of sintering occur in various pyro-processing of fines lying in close quiescent contact, such as powdered metals practices, some types of pellet induration, firing of briquets, or other compacts, where the entire bed is brought to, and held at, the high reaction temperatures of sintering. Figure 1, The continuous sintering process as originally conceived consisted of intimately mixing carefully proportioned burdens, placing them in a comparatively thin, draft permeable layer, on a moving grate and igniting the surface while drawing sir through the bedded burden. The moving grate was advanced slowly as the line of burning fuel travelled from the surface to the bottom of the bed and no more fire zone could be seen.

Jan 1, 1973

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. &apos;Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH&apos;s that were in place within the study area, the results showed a possible elimination of 34 DDH&apos;s without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto&apos;s Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology&apos;s photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By L. Mead

Dimension stone is a natural stone (granite, marble, limestone, sandstone and slate) that can be quarried, cut and shaped to conform to acceptable industry standards for size, consistency and durability. There are numerous outlets for the finished product in exterior and interior architectural and design applications. A continued growth market is with residential usage— particularly in new, upscale construction. This has become a competitive market between domestic producers and lower cost imported products. These imported products have become available at many of the building supply retail outlets and have increased the use of stone in residential construction and renovation. The traditional architectural application of dimension stone is tied to commercial and institutional building construction trends and market. There has been a noticeable increased usage of stone in the Sun Belt. This stone is usually supplied by local fabricating shops. It is used in the exterior and interior of shopping malls. This market generally uses local stone sources. It has increased the demand for sandstone, limestone and quartzite in this region of the country.

Jan 1, 2005

By K. P. Black, G. W. Sevick, D. E. Hockley, K. S. Sexsmith, J. T. Chapman

Mineralogical analyses of carbonates in depyritized tailings and pyrite concentrate (from depyritization of the tailings) were completed as part of the tailings characterization for the Crandon Project, a massive sulfide deposit in northeastern Wisconsin. The mineralogical study was designed to determine the proportion of calcium and magnesium carbonates, and therefore the effective buffering capacity of carbonates in the tailings. The depyritized tailings are net acid consuming and will be stored in a surface tailings management area. The pyrite concentrate is net acid generating and will be used as backfill in the underground mine workings. The majority of carbonates in the depyritized tailings were ferroan dolomite containing 10 to 15% iron (by weight) and lesser amounts of siderite and magnesian siderite. The proportion of calcium and magnesium-rich carbonates corresponds to several independent tests of carbonate neutralization potential (CO3-NP) availability. The pyrite concentrate had less CO3-NP, indicating segregation of the carbonates during pyrite flotation. These carbonates reported higher iron contents, consistent with the relatively lower availability of CO3-NP in the pyrite concentrate.

Jan 1, 2002

By Eric C. Schwamberge, Clem A. Pelletier, Deborah L. Muggli, George W. Poling

The Pit Lake at Island Copper has evolved into a 3-layered meromictic system. Acid Rock Drainage (ARD) is collected and injected into the lake at 220 m depth via 2 diffuser systems. In situ dye studies were conducted during 2 differing hydrological regimes in order to determine the behavior of the ARD plume within the Pit Lake. Results indicated that when runoff from the waste dumps was low, the injected ARD remained within the bottom half of the intermediate layer of the Pit Lake, initially below depths of 90 m. However, when runoff from the waste dumps was high, the injected ARD at -220 m depth rose through the intermediate water column layer rapidly, but did not breach the top pycnocline at -10 m depth. Overall, the system is currently performing as a mixing bowl with a strong boundary or cap at the upper pycnocline. maintaining mixing below the 10 m depth water level.

Jan 1, 2000

By Virginia T. McLemore

The Black Hawk district in New Mexico hosts an unusual type of deposit: arsenide five-element veins. These deposits are Ag-Co-Ni-Bi-As-bearing carbonate veins with local concentrations of U, Pb, Zn, Sb, and other elements. They are high-grade silver deposits (1000s g/t Ag), but low tonnage (<1 Mt) and difficult to find. By 1881, claims were staked and a town developed. It is estimated that >$1,500,000 was produced in 1883–1893, when Ag prices dropped due to the 1893 Ag panic. Solid Silver Mining Co. produced $600,000 from the Black Hawk mine; one car load contained $28,000 worth of silver! The town of Black Hawk grew to 125 population by November 1883. By the end of 1893, the town was vacant; nothing remains. The district was idle until 1916, and the mines operated sporadically since because of lack of available capital, water issues, and difficulty in finding ore shoots. The area is a favorite for mineral collectors. Tungsten was found in the district in 1935 in quartz veins associated with pegmatites. Metal production from 1881–1960 is estimated as 3,000 lbs Cu, 1,000 oz Au, 1,286,000 oz Ag, and 4,000 lbs Pb. In addition, 10,542 short tons of 2.7–71% WO ore and 615 short tons of fluorspar ore have been produced from the district.

Feb 1, 2025

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By S. E. Sankey

High anionic functionality acrylamide co-polymers and poly(sodium acrylate) are used as red mud flocculants in bauxite processing operations. These synthetic polymers are effectively displacing starch as the dominant polymer in red mud settling. The performance of these polymers is primarily dependent on the bauxite mineralogy, the alkalinity of the red mud slurry, and the anionic functionality and molecular size (viscosity) of the polymer. In this paper, the physical and chemical properties of the synthetic watersoluble polymers will be reviewed. The relationship between polymer structure and red mud slurry properties as they control polymer performance in settling red muds common to digester and washer circuits will be illustrated. The availability of polymers of varying functionality and viscosity will permit bauxite processors to make significant improvements in the economics of red mud disposal and valuable reagent recovery.

Jan 1, 1982

By Steve Kral

For a state whose roots are in mining, most Colorado residents probably do not realize that the industry still contributes heavily to the state’s economy. In 2005, the industry contributed, directly and indirectly, about $8 billion to the state’s economy, according to the Colorado Mining Association (CMA). It employed nearly 10,000 people at mines and support businesses. And the mining industry in Colorado is one of the highest paying occupations in the state, averaging about $80,000 a year in wages and benefits. The state’s coal mining industry produced nearly 36 Mt (40 million st) of coal in 2005, valued at $800 million, the CMA said. That was seventh in the nation. And Colorado’s only major gold mine produced 10.2 t (329,000 oz) last year, valued at $124 million. That was third in the nation. And Phelps Dodge’s Henderson Mine produced about 12.7 kt (28 million lbs) of molybdenum, valued at $350 million. Colorado is the largest molybdenum producing state in the nation.

Jan 1, 2006