Search Documents

By R. Addison, P. V. Avotins, D. W. Kestner, M. F. Dibble, L. A. Haas, M. D. Flavel, D. Halbe, D. J. Barratt, G. V. Jergenaen

Mineral processing in 1980 can be described by several key words, familiar to the industry throughout the past decade: complex, low grade, environmental, energy, high tonnage, and economics. Flowsheets have become more complex in order to treat lower-grade, finer-grained, more complex ores and still meet environmental and economic constraints. Operators and researchers have had to cope with these problems, which have resulted in marked trends in mineral processing. The use of advanced instrumentation in process monitoring, control, and modeling has been increasing to deal with fluctuating ore grades, higher plant capacities, rapidly rising operating costs, and process complexities. The industry has been presented with new generations of equipment that reportedly do the job more efficiently and at a reduced cost. The need to meet stricter air and water environmental standards has resulted in a concerted effort by the mineral industries to obtain an appropriate balance between the needs of mining and mineral processing and the requirements for proper environmental, safety, and health protection. Energy and economic considerations have led to increased equipment size, particularly in grinding, flotation, and conveying. Throughout all phases of mineral processing there has been an effort to reduce energy consumption. One avenue followed by researchers and operators was the testing and use of chemicals to reduce energy requirements.

Jan 5, 1981

By O. Noirot, H. C. Owens, P. D. Rao, D. E. Walsh, J. R. Mokka

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10- 20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C range.

Feb 24, 1997

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

By I. R. Miller

The purpose of this discussion is to try to offer some suggestions as to how the zinc and lead markets will perform over the balance of the decade, review some of the factors influencing production and come to some conclusions regarding prices. The past 2 years have been simply awful in terms of consumption, prices and overall profitability for the industry. In looking ahead to the year 2,000, it is probably not a bad idea to look back about 20 years to see where we have been and how we got to where we are. Zinc consumption from 1950 to the early 1970's increased steadily and rather nicely at an annual average rate of close to 4.0%. It was starting in the early 1970's that things started to get volatile and at times, difficult for the industry. The general economic boom of the early 70's was marked by annual consumption rates close to 5.0 million tons, a level not seen again for over 10 years. The First Oil shock of 1973-74 was followed by the sharpest consumption drop in memory. In two years, Western World zinc consumption fell 27%. While our chart shows a rather dramatic recovery thereafter, the average annual growth rate since 1970 has only been a rather modest 1.5%.

Jan 1, 1992

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By Y. Guan

The adsorption of zinc species onto silica in ammonical solutions has been studied. Adsorption isotherms reveal that increasing adsorption occurs as the solution pH is made more alkaline. Fr-IR spectroscopy revealed that the adsorbed species is a zinc ammine complex.

Jan 1, 1993

By P. Hambach

Murer Company, Andermatt, Switzerland, can claim to have done pioneer work in the construction of inclined shafts. This happened in 1968/69, when we decided to bore with a Wirth tunnel borer an inclined shaft, 1100 m in length, 3.0 m in diameter, and with a grade of 65%, in the 2400 kilo pascall per sq. cm granite of the Montblanc Massive. The whole excavation was accomplished in ten months which, at least for European conditions, can be claimed as a record. It was, at least to our knowledge, the first inclined shaft to be bored full-face (Fig. 1). Encouraged by the experiences and performances attained at Châtelard, we approached other projects of the same kind. We were awarded, together with Hochtief Ltd., Essen, a contract from Schluchseewerke, Freiburg, Germany, in December 1969, for the construction of a penstock for the Hornbergstufe at Wehr, Germany, with a diameter of 6.3 m. This inclined shaft with a grade of 55% is located in Schwarzwalder granite with a compressive strength of up to 2000 kilo pascall per sq. cm, about 31,000 psi. As no exact geological data were available about the rock to be worked, and a fault zone from 80 to 150 m long had to be faced, as well as a few individual fissures of varying thickness, it was decided to use the multi-stage method. The 3-m diam tunnelling machine which had driven the oblique shaft at Châtelard had now finished work, and an immediate beginning was made with driving the pilot staft. This was very welcome to the contractor, since exact information about the type of rock present and the inflows of water was required immediately and before the final borehole diameter was fixed, for the purpose of dimensioning the supports to be subsequently installed.

Jan 1, 1974

By T. S. Golosinski

Introduction Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost. Both work in very difficult conditions and wear out rapidly. As a result, frequent rope changes are required resulting in substantial cost and productive time loss. Although performance of rigging has a profound impact on dragline efficiency, there are no common, industry accepted standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The performance of drag and hoist ropes depends on: •rope construction that should closely match requirements of the specific application, rope operating conditions and its maintenance and • correct definition and application of the rope discard criteria so that full advantage of the rope can be taken without endangering safety of its operation. This paper reviews the present practice related to all these factors. Its findings are based on the wide survey of the present industrial practice. Field survey In total, 33 North American dragline applications were surveyed of which 17 were Bucyrus-Erie machines, 10 were Marion and six were Page (now P&H). Most of the draglines were stripping overburden in coal mines, but the survey also included some unique applications such as phosphate mining in Florida and oil sand mining in Alberta. Hoist drive power of the surveyed machines varied from 300 to 7775 kW (400 to 10,400 hp). Drag drives varied from 300 to 5815 kW (400 to 7800 hp). Boom lengths varied from 37 to 110 m (120 to 360 ft). Bucket sizes varied from 5 to 96 m3 (6 to 115 cu yd). The hoist and drag ropes installed on the surveyed machines were supplied by 10 rope manufacturers and differed widely in type and construction. Most common rope strand constructions included standard strands, Seale, Warrington, Warrington-Seale and Filler-Seale. Results of the survey [ ] Working conditions Working conditions of hoist and drag ropes are quite different. The first cope primarily with bending on rope drums, point sheaves and deflection sheaves, and with tension force imposed by the bucket and its load. The drag ropes are exposed to severe abrasion at the pit crest, and to severe bending and crushing at fairleads, all while coping with tension forces imposed by resistance of the bucket to dragging. Bending of drag ropes at house rollers and at rope drums is of minor importance for their performance. Differences in working conditions result in different wear patterns, which make it feasible to install discarded hoist ropes to further serve as drag ropes. The hoist ropes wear primarily due to fatigue breaks of wires, while the drag ropes are subject to severe abrasion of outside wires, rope deformation and internal wire-strand breaking. The last is often indicated by the reduction of rope diameter. The summary of working conditions for the surveyed draglines is shown in Table 1. For simplicity, Table 1 does not include the data on rope bending at the fairleads, nor at the deflection rollers and house rollers. Similarly, Table 1 does not include the data on drag rope bending (other than that on the rope drum), as its influence on rope life is insignificant in view of severe abrasion and internal wear taking place elsewhere. The following abbreviations are used in Table 1: [D - diameter of rope drum. DP - diameter of boom point sheaves. d - rope diameter x - mean value of the measured parameter. s - standard deviation of x B/d - average bending ratio of ropes B/d =(D+ DP)/2d n - operational safety factor of the rope (rope stength) x (number of ropes) n(bucket load + bucket weight)] In terms of D/d ratio, the working conditions of hoist and drag ropes are similar to that in other related industrial applications. However, the safety factors of the dragline ropes are lower, which requires them to carry relatively large tension forces. The last explains the fact that the life of dragline ropes is low when compared to other industrial rope

Jan 1, 1995

By P. R. Clifford

Phosphogypsum is a byproduct of the manufacture phosphoric acid. There are approximately one billion tons of phosphogypsum stored in stacks in northern and central Florida. The Florida Institute of Phosphate Research (FIPR) is investigating potential uses of phosphogypsum. These include using phosphogypsum as a road base material, as a soil amendment in agriculture, as a daily cover in landfills, and as a construction material. The results of this research will be presented and will be discussed in light of regulatory barriers to the use of phosphogypsum.

Jan 1, 2002

By Charles E. Dunne

One of the most frequently asked quesitons is: "Where is copper (price and usage) going?" I will not attempt to forecast either the future price of copper or the future growth of the copper industry; rather I would like to discuss the current trends experienced in the smelting and refining terms and conditions for sales and/or purchases of copper concentrates. A brief review of contract language and terms, together with a review of the common jargon, I believe, would be helpful. To accomplish this review, I will first list what I consider the four basic parts or sections of a basic ore contract and then illustrate basic terms with calculations.

Jan 1, 1984

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By W. D. Hausel

The Wyoming craton in the western United States is a favorable terrane for diamond deposits. The craton hosts a variety of ultramafic, ultrabasic, and ultrapotassic rocks. Additionally, a few hundred 'kimberlitic' heavy mineral anomalies and some geophysical and remote sensing anomalies indicate the presence of undiscovered, mantle-derived, pipes in the craton. The Wyoming craton is separated into a Wyoming 'archon' known as the Wyoming Province, and the Colorado 'proton' known as the Colorado Province. The 'archon' underlies much of Montana and Wyoming and continues north into Alberta and Saskatchewan; the Colorado 'proton' underlies much of Colorado and a small portion of Wyoming. Although most exploration geologists would consider the 'archon' the most favorable terrane for commercial diamond deposits, the 'proton' has produced more than 120,000 diamonds, while the 'archon' has not been very productive.

Jan 1, 1996

By James J. Scott

To the safety engineer, mine planning engineer, and mine inspector associated with an underground operation, stability of the underground structure is of the utmost importance. In the United States in 1961 rock falls killed 167 miners, crippled many more, and cost the industry a fortune in lost equipment and production. Much research has been carried on to try to find ways to eliminate this loss of life and property. Within the past few years the interest in rock mechanics as a science has been at its highest point, Private industry, government agencies, universities and foundations have launched studies to gain a better basic understanding of the stability of underground openings.

Jan 1, 1966

By B. Fitch, E. J. Roberts

Definitions and Terminology Classification is defined within this section as the separation of solid particles into size or weight fractions or classes by differential settling through a fluid. It is usually thought of as a size separation, but is actually made on the basis of particle settling rate, and so is affected by any variations in particle density and shape. The fluid may be liquid (wet classification) or gas (dry or air classification). This section will treat only wet classification. There are two basic types of classification; pool and hydraulic. In pool classification a suspension of feed particles is fed into and out of a pool of some kind at such a rate that only part of them¬ the coarser and faster-settling part-has time to settle out. The remain¬der overflows as fines. In hydraulic classification the feed suspension is introduced into or above one or more columns or pockets through which water is rising at a controlled velocity. Coarse particles subside through the pockets and are removed through spigots. Those which settle slower than the rising velocity in any column or pocket are (at least ideally) prevented from subsiding and so must overflow. Hydraulic classifiers or sizers are capable of making far sharper sepa¬rations than pool classifiers. The force causing settling may be gravity, or alternatively may be from centrifugal acceleration as developed in a centrifuge or hydra cyclone. Two things are needed to characterize the separation produced by classification: first, the size, D„ or equivalently the screen mesh at which it is made; second the sharpness of separation. Separation size may be defined in various ways. In closed-circuit grinding it is commonly specified by some point in the overflow screen analysis: For example, 5% on 65 mesh. In other applications, notably

Jan 1, 1985

By L. H. E. Weyher

A mine is essentially a vast materials-handling system. All other systems found in the mine exist to one degree or another to support the materials-handling functions, from the cutting at the face to the hoisting in the shaft. In this chapter computerized planning of underground materials-handling systems will be examined by dividing this function into: (1) the planning of the production section, and (2) the planning of underground rail or belt haulage from the production section to the shaft, slope, or surface. While alternative divisions might focus on the different materials- handling functions, i.e., production, supply, and manpower transportation, historical computer analysis has focused on the various systems rather than functions. The emphasis in this chapter is directed toward coal mine applications; however, most of the programs and methods are equally applicable to other underground mines. Markedly different methods are encountered in each system, and moreover, marked differences exist in the nature and the degree to which the materials-handling subsystems in each interact with the environmental or support systems. The most intimate interaction exists at the faces where geologic, human, and machine performance factors are closely related and constantly varying. In view of this, the planning of the materials-handling systems for the face will usually stress flexibility, while the outby materials-handling systems will generally place decreasing emphasis on flexibility and more on system reliability, capacity, and cost effectiveness. Thus, hoisting and main haulage systems are generally designed and constructed as permanent installations and cannot be readily changed, whereas secondary haulage systems and face operations are relatively mobile. These differences may have considerable significance for the mine planner in making technical and financial comparisons of alternatives to provide the scheduled mine production.

Jan 1, 1979

By N. C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U. S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, preliminary results, and remediation ideas based on field observations are presented in this paper.

Jan 1, 1995

By Malcolm Ross

The Reserve Mining Co., in the processing of taconite iron ore quarried from the Peter Mitchell Pit, deposited the finely crushed waste rock into Lake Superior near Silver Bay Minnesota. In the early 1970s The U.S. Environmental Protection agency filed a lawsuit against Reserve Mining Co., asking the court to force the company to stop dumping into the lake. On April 20, 1974, after a lengthy court battle, the U.S. District Court concluded that the Reserve Mining discharge into Lake Superior violated federal and state pollution laws and thus ordered Reserve Mining Co., to halt the lake disposal of taconite tailings. At the time many feared that some of the mineral particles contained in the tailings (alleged to be asbestos or asbestos-like) would cause human health problems. This Conference was thus convened to readdress the problem of the mineral content of the Biwabik Iron Formation and to whether any minerals contained in the ore could cause human disease. The four papers given in this session address the nature of the mineral particles in the taconite rock, the definition of the term ??asbestos?? and the history of the legal controversy over the possible health effects of certain mineral particles contained in the Biwabik iron range ores. Paper 1?Geology of the Biwabik Iron Formation and Duluth Complex Mark A. Jirsa, James D. Miller, Jr., G.B. Morey The Biwabik Iron Formation was a principal source of ore for the American steel industry during the 20th Century. The unaltered iron deposits, called taconite, contain approximately 30% iron and 50% SiO2. About 75% of the iron in taconite resides in the mineral magnetite, the remainder is largely in iron carbonate and several iron-silicate minerals.

Jan 1, 2007

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001