Search Documents

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

By D. W. Hutchinson

One of the most important problems facing the coal industry today is the disposal of refuse from the coal preparation plants in a safe, economical, and efficient manner while complying with all legal requirements. The most commonly used refuse disposal method has been landfill/impoundment. In this method, the coarser refuse fractions are disposed of by layering and compaction into a landfill. The fine coal slurry refuse fraction is impounded in a dam constructed of a portion or all of the coarser refuse fractions. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the preparation, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. At the time of the promulgation of the new Federal regulations, United States Steel Corporation was in the process of designing the Cumberland preparation plant. As a result of the new regulations

Jan 1, 1977

By Y. A. Attia

Auriferous sulfide ores often contain very finely disseminated gold and other precious metal particles inside the sulfide crystals. The encapsulation of precious metal particles gives rise to the refractory nature of such ores to current extraction methods. As a result, these fractions are frequently lost in the tailings. The purpose of this work was to investigate the feasibility of pretreating these refractory tailings with bioleaching before employing standard extraction techniques such as cyanidation. Leadville gold ore tailings containing auriferous pyrite were first concentrated by froth flotation. The pyrite concentrate was treated for different periods of time with 12 weeks adapted thiobacillus ferrooxidans before cyanide leaching. The bioleaching of the concentrate before cyanide leaching increased the gold extraction from 32% to 95% and that of silver from 48% to more than 98%.

Jan 1, 1987

By Kirk H. P. E. McDaniel, Mark T. Strever, Keith G. Jr. Wallace

This paper presents the design and installation of an underground ventilation remote monitoring and control system at the Waste Isolation Pilot Plant. This facility is designed to demonstrate safe underground disposal of U.S. defense generated transuranic nuclear waste. To improve the operability of the ventilation system, an underground remote monitoring and control system was designed and installed. The system consists of 15 air velocity sensors and 8 differential pressure sensors strategically located throughout the underground facility providing real-time data regarding the status of the ventilation system. In addition, a control system was installed on the main underground air regulators. The regulator control system gives indication of the regulator position and can be controlled either locally or remotely. The sensor output is displayed locally and at a central surface location through the site-wide Central Monitoring System (CMS). The CMS operator can review all sensor data and can remotely operate the main underground regulators. Furthermore, the Virtual Address Extension (VAX) network allows the ventilation engineer to retrieve real-time ventilation data on his personal computer located in his workstation. This paper describes the types of sensors selected, the installation of the instrumentation, and the initial operation of the remote monitoring system.

Jan 1, 1995

By V. K. Kollipara

Dust dispersion characteristics in mine airways are important for developing engineering controls for dust and explosions. Authors here have used CFD modeling approach to analyze the dust dispersion characteristics in mine airways. The technique was initially validated with the published field experimental data. The results obtained were in a reasonable agreement. CFD validation results show that in a single entry the dust concentration decreases exponentially as a function of distance. Finer particles can travel up to a distance of 350-400 m away from the source. Parametric studies indicate that air velocity and input dust concentration has significant influence on dust concentration distribution. CFD modeling was then applied to study the dust dispersion characteristics in a room-and-pillar mine layout. Preliminary results show that dust concentration distribution is highly dependent on the airflow patterns and air velocity distribution. The distribution is not exponential until the velocity in the travel way becomes uniform. Data developed in this study may be used to design mine layouts and engineering controls for dust control and explosions.

Jan 1, 2011

By J. R. Sturgul

Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato's program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1 987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modem versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 1, 1987

By Tania Schmid, Marco Portal Valdivia, Sandra Nowosad

Today’s mining industry faces rapid transformation driven by automation, climate responsibility, and ESG demands, requiring more than technical expertise. Future mining engineers must blend engineering excellence with key human skills such as communication, leadership, resilience, empathy, adaptation to change, curiosity and lifelong learning. Based on two recent surveys, one to senior leaders with over ten years of experience in the mining industry and a second, focused on understanding the perceptions of young professionals, this paper explores which skills become core competencies by 2030 for navigating complexity, leading responsibly, and enabling sustainable transformation. Furthermore, it also examines how educational institutions can adopt strategies to foster the development of these critical skills, preparing future mining talent for evolving challenges.

Feb 22, 2026

By Hyung-woo Kim, Kiyoung Sung, Sup Hong, Jung-Yeul Jung

Many concepts for the commercial production of deep-seabed manganese nodules have been studied since the 1970s. However, the bearing capacity of the deep seabed is not strong because it is composed of fine particles with high moisture content. So it is impossible to carry manganese nodules in the collection system. Therefore, the validity of continuous mining by riser pipe from the seabed to the vessel is highly appreciated. A continuous mining system is composed of mining vessel, lifting pipe, buffer system, transport tube (flexible pipe), and self-propelled mining robot. A conceptual diagram of this system is shown in Fig. 1(a). Korea Research Institute of Ships and Ocean Engineering (KRISO) developed a deep-seabed self-propelled mining robot called "MineRo" to collect manganese nodules in 2012 (as shown in Fig. 1(b)). In 2013, real sea experiments at around 1380 m depth were carried out to evaluate the collecting and driving performance of MineRo. However, we found that the roller in MineRo did not work well at times. To elucidate the problem, we analyzed the rheological characteristics between the bushing and drive shaft under deep-water conditions.

Sep 1, 2014

By John A. Breslin

The U.S. Bureau of Mines develops technology to help ensure that the Nation has an adequate and dependable. supply of minerals at reasonable economic, human, and environmental cost. Our research programs seek improvements for almost every aspect of the mineral production cycle--from evaluating the availability of minerals, removing the ore from the earth, to enhancing the performance of mineral materials. The health and safety of the men and women who work in the Nation's mines and minerals processing plants and the environmental impact of mining and mineral processing are major Bureau research concerns. In recent years, the U.S. mineral industry has found it increasingly difficult to compete for a share of world markets. Many foreign producers benefit from lower production costs and higher grade deposits. Some foreign governments subsidize their mineral industries and impose fewer restrictions with respect to environmental controls and health and safety regulations. If the United States is to compete in world mineral markets, innovative technology must be found to lower the cost of recovering and processing minerals. Mining and mineral processing research by the Bureau identifies ways to help the country maintain a sound, competitive industry and a dependable mineral supply, so vital to economic growth and the national security. This work includes efforts to improve existing techniques and procedures; but more and more of the Bureau's resources are being focused on long-term, high-risk research directed at developing new approaches to mining and mineral activities--approaches like in situ mining. Bureau scientists are studying the mining applications of computer assisted mining and investigating a variety of "high tech" approaches to extractive metallurgy. Such cutting-edge research will be necessary if major advances in health and safety, environmental quality, strategic and critical minerals availability, and overall U.S. competitiveness are to be achieved. It is just such high-risk research that the industry cannot afford to conduct itself, but--in the long run--cannot afford to be without. It is this type of research that will help us arrive at a revolutionary breakthrough rather than small incremental changes in health and safety technology as well as recovery methods. Our mining and mineral processing research is also directed at reducing the Nation's dependence on imports of minerals that have key defense and industrial uses. Some of these strategic and critical minerals are particularly vulnerable to supply disruptions. We are working on technologies that would allow the United States to take advantage of domestic sources of these minerals--sources consisting primarily of deep or low-grade ores, ores with complex mineralogy we do not yet know how to process, and small deposits that are now uneconomical to mine and process. Other research activities focus on ways to reduce the Nation"s consumption of key minerals and increase the recycling of these minerals. The opportunities in this area include coal. The current middle eastern crisis reinforces the need for a stable energy supply--preferably a domestic supply. The extensive reserves of coal in this country are well documented. Perhaps what is not as well recognized is the impact that the price of coal can have on its competitive position both for domestic fuel selection considerations as well as for the ability of this country to compete in the coal export market. Today, the role to the United States is as a reliable, but high-cost exporter of high-quality coal. U.S. export coal competes with supplies from other major suppliers, including Australia, Canada, Poland. If U.S. mining costs were lowered by at least $8 per ton in the year 2000, then coal exports would surge by a projected 46 percent, and U.S steam coal displaces significant quantities of foreign coal imports in Europe. Further cost reductions would make

Jan 1, 1991

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the high noise is the drilling of the roof bolt holes, especially in hard rock. A previous research shows that the specific energy consumed in drilling the bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process to produce heat, bit wear and noise. Therefore, control of drilling operation to achieve a higher bite depth can provide an opportunity to reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and to develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show significant reduction in noise dose can be achieved by drilling in medium hard rock at a reasonably high bite depth. This paper presents the findings from the laboratory experimental studies conducted so far.

Jan 1, 2013

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

Introduction The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track" or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.3 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV, Pre-Feasibility Planning Proper early planning and identification of priority items were necessary to expedite project progress. On April 1, 1978, HIMCO leased the rights to the Borealis prospect and initiated exploration activities almost immediately. Since Borealis was showing excellent potential for mine development, an effort to clear the way environmentally was initiated during the summer of 1979. With the Borealis properties located within the Toiyabe National Forest, the US Forest Service (USFS) was recognized as the "lead" or respon¬sible agency for addressing the environmental issues. Early scoping of the environmental issues by both HIMCO and the USFS allowed HIMCO to take the initiative and address two potentially critical issues-archaeological and biological. Third party consultants, agreed upon by HIMCO and the USFS, were contracted to conduct archaeological and biological surveys. Desert Research Institute of Reno, NV, provided archaeological services, and JFL & Associates of Boulder, CO, provided biological services. These efforts began in the fall of 1979 and continued through the summer of 1980. Conservative Design Criteria By adoption of conservation design criteria, flowsheets and processing data required for detail engineering were firmly established with a minimum of impact on schedule. On Oct. 21, 1980, HIMCO formally initiated a feasibility study to evaluate the Borealis project. Four organizations were contracted for particular scopes of work: • John T. Boyd Co.: Ore reserve estimation, preliminary mine plan, and mine capital and operating cost estimation. • Bechtel Civil and Minerals: Conceptual engineering, processing capital and operating cost estimation. • Hazen Research Inc.: Metallurgical testing. • Sierra Pacific Power: Cost estimation for power supply. Metallurgical testing and conceptual engineering of both heap and agitation leach flowsheets were investigated concurrently. Numerous economic evaluations were conducted for both heap and agitation leaching at varying production capacities. The results indicated a heap leaching flowsheet treating 454 kt/y (500,000 stpy) yielded the best economics and was compatible with the "fast-track" development goal. Conservative design criteria was established to provide operating flexibility and ensure plant productivities. A summary of major design criteria is presented in Table 1. HIMCO assembled the results of the studies of the various consultants along with internally generated studies to produce the feasibility document. The decision to supply 100% equity by HIMCO rather than arrange project financing help to expedite the project. Cooperation Between HIMCO and Regulatory Agencies With cooperation and mutual trust established between HIMCO and regulatory agencies, the time required for environmental permitting was streamlined as much as practical. To expedite the required construction permits, HIMCO proposed to the USFS that HIMCO fund the total cost of an Environmental Assessment Report (EAR) and that issues be addressed at the technical level of an Environmental Impact Statement (EIS). The previous studies on the critical issues of archaeology and biology provided HIMCO with the information to satisfy the proposed approach. Houston International Minerals and the USFS agreed to have Environmental Research and Technology (ERT) of Fort Collins, CO, prepare a draft EAR for the USFS.

Jan 11, 1983

Start with your assessment of the minerals business —domestic mining as well as operational and consulting perspectives. As a third generation miner, I have been living the mining business for as long as I can remember. I have watched commodity prices produce boom and bust cycles in places like Price, Utah (coal), Douglas, Arizona (copper) and Eureka, Nevada (gold). It is unsettling to see how our industry has fluctuated, but it always seems to rebound if you can stick out the down cycles. However, our most recent dip in the cycle was, in my opinion, characteristically and permanently different. In the past, when prices went south, people hunkered down and waited out the cycle until things came back, much the same as they had every other time. Not this time. This time, we saw a consolidation of the industry in proportions never seen before. Mega-mergers like Exxon-Mobil, Phelps Dodge-Cyprus and Newmont-Normandy have changed the complexion of our industry forever. And that is true not just of the mining companies; it happened across the supporting business lines as well. As a midsized niche engineering and environmental service provider to the mining industry, companies like mine are few and far between these days. The lean cycle saw many of the small and midsized providers get gobbled up by consulting giants like URS and TetraTech. The mentality of a mega-company, whether a commodity producer or a goods or service provider, is different than that of their small- and medium-sized counterparts.

Jan 1, 2005

By H. Demirel

This paper deals with concentration of hematitic-limonitic iron ores. The ore sample obtained from Karakuz (Turkey) contain:. about 40-46 I Fe. First, a low intensity magnetic separation process was employed to separate the strongly magnetic particles cf "-10+2 mm" and "-2+0.075 mm" size fractions and magnetic concentrates with 59.1 % Fe aid % 58.0 Fe were obtained respectively. The non-magnetics of both fractions were then fed to a nigh intensity permanent magnetic separator. The Fe contents of "-10+2 nun" and "2+0.075 mm" size fractions were increased from 28.2 to 51.13 and from 35.4 7. to 43.25 respectively after single pass. Easing on these results, it was concluded that the high intensity permanent magnetic separator could he used as a pre-concentrator f.7.1- hematitic-limonitic Karakuz iron ore.

Jan 1, 1991

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By Brent W. Madsen

To assist in fulfilling the Bureau of Mines goals of maintaining adequate mineral supplies to meet national economic and strategic needs, and to minimize the environmental impacts associated with mineral-processing operations, a leaching-solvent extraction-electrowinning technique was compared with a leaching-cementation technique for processing low-grade copper ores. Large-scale laboratory column leaching tests (6 to 7 tonnes) were conducted on minus 37-cm chalcocitic ore using ferric sulfate leach solutions at 25° C. Two columns contained 11 percent minus 1.27-cm fines, and two columns contained 32 percent minus 1.27-cm fines. After 416 days of leaching ore samples containing 11 percent minus 1.27-cm fines, copper extraction was 48 and 51 percent for the leach-cementation and leach-solvent extraction-electrowinning procedures, respectively. When leaching ore samples containing 32 percent minus 1.27-cm fines, the leaching-solvent extraction-electrowinning technique extracted 60 percent of the copper after 568 days, whereas the leaching-cementation technique extracted only 48 percent of the copper. In the latter test, leach solution ponded on the ore, which reflected a decrease in ore column permeability. The decreased permeability was attributed to the generation of excessive amounts of iron salts during cementation; the salts precipitated on the fine ore particles and in the interstices, thus plugging the column. This decrease also lowered the available oxygen, resulting in poor aerobic bacterial activity which slowed the oxidation rate of ferrous ions to ferric ions. Sulfuric acid required to maintain a leachant pH of 2 was nearly halved when copper was recovered by solvent extraction and electrowinning rather than by cementation.

Jan 1, 1979

By Haydn H. Murray

The three major catalyst markets that utilize industrial minerals as raw materials are petroleum refining, chemical processing, and emission control. Because of economic, competitive, and regulatory pressures, catalyst producers are pushed to develop products with improved performance to meet changing environmental standards. Also, refiners are demanding new families of cracking catalysts that will crack residual fuels. In 1987, worldwide cracking catalyst sales amounted to $457 million (Occelli, 1988a). Recently enacted federal and state laws to improve air quality have prompted strong growth for environmental catalysts, which in 1989 accounted for more than a third of the $1.9 billion catalyst market in the United States (Farrauto, Heck, and Speronello, 1992). A catalyst is a material that promotes or enhances a chemical reaction but does not itself enter into the reaction. One of the more important mineral groups used as catalysts is clays. The first recorded use of clay as a catalyst was its use in the dehydration of alcohol (Bondt et al., 1797). Clay minerals that are used as catalysts are kaolinite, halloysite, smectite, palygorskite, and sepiolite. Minerals used as catalysts, catalyst supports, or as a raw material to make zeolites are kaolinite, halloysite, sodium montmorillonite, calcium montmorillonite, hectorite, palygorskite, sepiolite, talc, calcined kaolinite, gibbsite, chlorite, and titanium dioxide.

Jan 1, 1994

By Brent K. Nelson, D. Lee Petersen, Charles R. Nelson

INTRODUCTION The Soudan 2 Cavern was completed in 1986 as a physics research laboratory located 713 m below ground in northern Minnesota. A paper in the 1985 RETC proceedings presented the background and planned usage for the cavern, site investigation and rock conditions, contract documents, and a bid summary. This is a follow-up paper describing construction of the cavern. The Soudan 2 excavation, 71.8 m long by 13.9 m wide by 11.6 m high, was excavated by drill and blast methods and mucked by crawler tractor and mine hoist. The excavation sequence consisted of twin top-heading pilot tunnels followed by removal of the top heading pillar and finally the bench. Various blasting designs were used to achieve adequate breakage and acceptable levels of blast damage control at the cavern perimeter. The geologic conditions exposed in the cavern, and the support needs of the rock encountered, are compared to the conditions interpreted from the site investigation. The influence of specific geologic features on cavern performance will be described. Initial support and final lining consisted of full length grouted rockbolts and reinforced and plain shotcrete. Trials were conducted with steel-fiber reinforced shotcrete and microsilica additives. The performance of the rock and support systems was tracked with single point extensometers, convergence measurements

Jan 1, 1987

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010