Search Documents

By J. K. Horbaczewski

The reclamation of an open dragline pit (Pond A3P-2) at the Gibbons Creek lignite mine in east-central Texas required neutralization of acid mine pit water. At the start of treatment with hydrated lime (Ca(OH)2) on March 28, 2000, the pond had partially filled with 913,000 m3 (740 acre ft) of pH 4.9 water. Another 666,600 m3 (540 acre ft) of pH 3.3 water was pumped in from an adjacent pit (PitA3P- 1). By the end of the project (July 5, 2000), a combined volume of 1,579,000m3(1,280ac-ft or 417milliongal) in PondA3P-2 had been successfully treated to pH 8.2 with 431 t (475 st) of lime. This was two to three times more neutralizer than laboratory trials and detailed chemical titration had predicted. The main reasons for the difference are thought to be the inadequate representation in a laboratory setting of some of the chemical reactions that occurred in the field, including incomplete mixing of reactants, reactions with clay minerals in the pit walls, the kinetics of biologically-mediated reactions and the kinetics of aluminum oxyhydroxide polymerization (aging).

Jan 1, 2002

By Germán Toledo

The closure of TSF represents a critical milestone in the life cycle of mining operations, requiring the integration of technical, environmental, and social dimensions to ensure long-term safety and sustainability. The GISTM introduces the concept of “safe closure” as a demonstrable technical condition in which there are no ongoing material risks to people or the environment. This status must be validated by an independent technical reviewer and formally approved by the Accountable Executive. This article presents a risk-based methodology to support the achievement of safe closure, aligned with the principles and requirements of the GISTM. The proposed approach emphasizes the need to identify, assess, and manage closure and post-closure risks progressively throughout all phases of the TSF life cycle: from site selection and design, through construction and operation, to closure implementation and long-term monitoring. The methodology integrates key elements of effective risk management, including comprehensive knowledge bases, consideration of climate change, credible failure modes, continuous monitoring, stakeholder engagement, and governance. The ALARP principle is applied to demonstrate that residual risks have been reduced to tolerable levels. By incorporating closure planning from the earliest stages and adopting a risk-based view throughout the entire life cycle, this methodology aims to support mining organizations in achieving a verifiable and responsible closure of tailings facilities, in line with international best practices such as those of ANCOLD and ICOLD. The proposed framework offers a practical contribution to strengthening the credibility, effectiveness, and sustainability of tailings closure processes.

Feb 22, 2026

By M. Gershon

The article is an excellent one, providing a basis for the conduct of the major tasks in underground mine planning and scheduling. I object to only one word. Since that word is featured in the title, it is a strong objection. The word used erroneously is optimization. There is no optimization performed in the article. By definition, an optimization is an approach that yields the best of all possible solutions. We can limit this definition to its narrowest sense, the optimization techniques of operations research such as linear programming, or broaden it to include less sophisticated search procedures that find the best mine plan or schedule. No such claim is made in the article. No optimization of any kind is performed. The major tool used is a simulation, which, in truth, is probably more appropriate for this problem than any optimization. But simulation does not optimize. It only allows for quick evaluation of many options, leading to the selection of the best plan "of those tried," not "of all possible plans." This article, of course, is not the first mining paper to make this error. It seems that the word optimization is used more to impress people than to refer to any act of optimizing. It is used in a way that implies "try to optimize" or "come close to optimize," but not to really do it. It is usually appropriate to quietly ignore this error. But when Dr. Chatterjee, who has done so much good work in true optimization projects and whose work I have come to admire, makes such an error, it is time to publicly dispute it. Having discussed this very point with him in the past, I am sure that he will agree. If he can support this position in his response, perhaps people will start to listen and we can reduce the number of false claims of optimization. This should be easy for him in this case since the approach he used, simulation, is the more appropriate one anyway.

Jan 1, 1987

By Douglas Banks

Construction for the new 2.5 MGPD raw water intake project commenced December 2002. The project, initially designed as a 12' Ø concrete lined intake shaft,145' deep, with two offset 24" lake taps, 520' and 470' long was subsequently “value engineered” running the two lake taps through a single conduit. The offset for summer and winter pools was accomplished via a second shaft located at the lakes edge. Construction involved the use of blind drilling techniques for the shaft development and drill and blast techniques for the tunneling. All works were completed through extremely hard crystallized sandstone. The project came online August 12, 2004.

Jan 1, 2005

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease with increasing volume, while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. However, as every ventilation instructor knows, the fact that head loss is a negative number (debit) and fan head is an energy addition (credit) is often a stumbling block to student or audience comprehension since the curves seem to reflect the opposite. It is possible to use the intuitively correct curves- pressure losses as negative values and energy additions as positive values - and still obtain the correct operating point. Adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure. With the standard approach, it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1999

Crushing and grinding The Crushing and Grinding Technical Committee There was substantial activity in the area of crushing and grinding with the improved outlook in the industry. The Crushing and Grinding Committee's theme of 1987's Annual Meeting in Denver was Fundamentals of Mechanical Design for Crushing and Grinding Mills. At the meeting, the concept of gearless sag mill variable speed drives was taken out of the closet, dusted off, and a wraparound motor was put on hard copy with the ordering of a 9.7- x 4.5-m, 8.2-MW (32- x 15-ft, 11,000-) sag mill. Additionally, comparisons were provided to the mill design of the gearless drive sag mill and the twin 4.5 MW (6000 hp) do variable speed drives placed on the drawing board for the Kennecott UCD Expansions. This involved a 10- x 4.5m, 8.9 MW (34- x 15 ft, 12,000 hp) sag mill. Differing opinions were also expressed in technical presentations pertaining to the need for quality mill specifications in design and manufacturing. J. Berney-Ficklin of Bechtel presented a paper outlining the need for quality design and manufacturing specifications in large scale grinding mills, and the overall cost reduction in capital and operating costs. Others presented differing specific views, but all emphasized a central theme. Quality and reliable designs in large mills should not be compromised. In-pit crushing applications continue to increase, overseas and in the US, in both mining and quarrying. Different in-pit crushing units have been classified as mobile, with integral transport systems; semi-mobile, typically modular systems that use separate transporters for repositioning; semi-stationary plants that must be dismantled before transporting and typically require earthwork and concrete foundation work; and stationary in-pit crushing plants, which remain in place for the life of the pit. The majority of equipment sales of conventional crushing and grinding circuits in 1987 were to gold mining operations. There have been two areas of end use: • conventional jaw/gyratory or impact crushing circuits preparing low grade ores for heap leaching; and • small scale sag/ball mill circuits preparing higher grade ores for classical cyanide leach/ recovery circuits. There was also continued interest in ABC and SABC circuits for both base and precious metals plants. High pressure roll crushers continue to attract considerable interest in the cement industry. There, they are used to prepare raw materials or clinker for subsequent ball/tube milling. However, they have apparently been less successful in the mineral industry where the energy savings/ capacity gains have been much less dramatic. Several papers covering the theory and application of these machines were presented in an industrial minerals session on cement at the SME Annual Meeting. The Third International Conference on Hydrocylones, held in England in October produced several papers of interest on classification and screening to the mining industry. In particular, a new cyclone apex, developed by Mt. Newman Mining, shows promise of reducing water flow to the cyclone underflow stream and, therefore, increased underflow pulp densities and reduced fines recycle in grinding circuits. A twin vortex hydrocyclone was also described and shown to give a sharper split than conventional units. Similar double cyclones were introduced in the 1950's, but failed to achieve widespread acceptance. This was due mainly to a proneness to blockage in the transitional zone. It will be interesting to see whether this latest variant can overcome this problem in the typical operation. A number of North American iron ore plants installed the capability to produce fluxed iron ore pellets. Most chose to grind the stone on site with circuits designed to grind taconite ore. Methods employed to grind this material included single-stage ball mills closed with fine screens, rod and ball mill circuits - both open and closed with cyclones - and semiautogenous mills, followed by ball mills closed with screens or cyclones. Dewatering and tailings disposal B.M. Moudgil and D.L. Sober, University of Florida Due to tightened environmental regulations and the need for more efficient land use, a greater interest in dewatering and waste disposal has developed. As a result, research efforts in flocculation, surface chemistry, and polymers science have focused on the problems related to the dewatering of solid mineral wastes. A few studies have been conducted to examine the flocculation process. Hogg et al., (1987) discussed the formation and growth of flocs. They determined the size and density of flocs was controlled by the physical conditions of the system (e.g. agitation,

Jan 5, 1988

By J. C. Cawley

This National Institute for Occupational Safety and Health study was conducted to focus future research on the most significant electrical problems in the mining industry. Data from 1,926 mine electrical accidents (including 75 fatalities) that occurred between 1990 and 1999 were studied. Coal and metal-nonmetal operator- and contractor-reported data are presented. All data used in this analysis were MSHA closeout data, except 1999, which were preliminary data. Electricity was the 4th leading cause of death reported in mining despite being the 14th leading cause of injuries. Electrical shock, not electrical burns, caused 70 of the 75 electrical fatalities reported. About one-half of mine electrical accidents and fatalities occurred during electrical maintenance. Suggestions for mitigating electrical hazards are proposed.

Jan 1, 2002

By G. E. Wasson

Coal in most refuse ponds including those owned by Consolidation Coal Company can be recovered by froth flotation techniques. Laboratory studies show that the flotation conditions required for coal recovery varied greatly from pond to pond. The variables found to be most important for high coal recovery and low product ash were: a) the amount and type of flotation reagents and b) the degree of conditioning before flotation. Coal recovery at a rate of 0.504 kg/s (2 tons/hr) was demonstrated at a pond site employing a mobile froth flotation unit.

Jan 1, 1988

By Lisa Morrison

The 11th Annual Mineral Economics and Management Society (MEMS) conference was held April10-12, 2002, in Montreal, Quebec. It consisted of a series of technical sessions. Each paper addressed the economic issues that are related to the changes that many people believe are now required in the mining industry. Some of the papers were directed at how the mining industry will handle the changes that will be required in its philosophy and operations management. Of equal importance was whether the industry possesses the toolkit necessary to effect these changes and emerge stronger from its challenges.

Jan 1, 2002

By T. H. Phillips

The Mission Mine is an open-pit copper mine located 18 miles south of Tucson, Arizona in the eastern foothills of the Sierrita Mountains. Mining is done on 40 foot benches using P & H 2100 shovels and 170-ton Terex trucks. Drilling is accomplished With two (2) Bucyrus-Erie 45R?s, one (1) Bucyrus-Erie 60R and two (2) Ingersoll Rand T-5?s. For secondary drilling. a Joy VCR-ISO truck mounted drill is used. The mine is currently operating 3 shifts/day, 7 days/week at 59,100 tons per day, with the mill receiving 28,500 tons per day. The management of the drilling and blasting program requires extensive record keeping in all phases of the operation. This is essential in order to evaluate different products and procedures.

Jan 1, 1988

The 2012 North American Tunneling (NAT) conference is expected to attract more than 800 tunneling and underground construction professionals. But don?t let the North American part of the meeting?s title fool you. Many of the attendees will come from all over the world. The meeting is scheduled for June 24-27 at the JW Marriott Indianapolis Hotel in Indianapolis, IN. In addition to two and a half days of technical programming, the accompanying exhibit has attracted 116 exhibitors in 140 booths. And the conference will include short courses, a field trip and plenty of social activities that will give attendees the opportunity to catch up with each other.

Jan 1, 2012

By B. Ollila, L. Brown

As mining fronts converge in sill pillar extraction, the mine seismic hazard can be significantly altered and large seismic events have been known to occur. This study used common seismological tools to analyze the extraction of highly stressed sills from two deep Canadian mines with the objective of characterizing the rock mass failure process and relation to large seismic events. The approach treated a sill pillar as a mine-scale failure process, meaning the temporal and spatial analysis scales needed to exist on a similar scale to a significant part of the mine. The temporal analysis scale overlapped with the entire mining sequence, included several years of data to establish long term change in the characteristics of rock mass failure. The spatial analysis scale included the rock mass surrounding a large part of the convergent mining sequence. To accommodate the large spatial and temporal scales, the highest magnitude 2% of events in the dataset were analyzed. Similar results were shown for sill pillars in both mines. Changes in event location, time, magnitude, energy index and apparent volume were similar to expected behavior of rock failure. Indications of strain hardening and strain softening were observed in the sills. The hardening period was characterized by a high rate of small events, high energy index and low apparent volume, giving an indication of high stress and low rock yield. The softening phase was characterized by a decrease in the rate of small events concurrent with an increase in the rate of large events, low energy index and high apparent volume, indicative of release of stress and increase in deformation. Large magnitude seismicity was strongly related to the softening phase, with several Nuttli magnitude 3.0+ events occurring shortly after the transition from hardening to softening failure regimes. Sill failure was indicated by consistently low EI and low levels of seismicity and seismic hazard in the sill pillar.

Apr 26, 2022

By C. J. Roos

Ground engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these ?consumable? items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corporation to predict the consumption of excavator teeth. This paper presents the results of a Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2009

By Donald A. Brobst

Barite, the sulfate of barium, occurs in many geological environments in sedimentary, igneous, and metamorphic rocks. The commercial deposits of barite may be classified into three major types. 1. Vein and cavity fillings that occur in rock fractures, along bedding planes, and in various solution structures. 2. Bedded deposits in which barite occurs as the principal mineral or cementing agent in stratiform bodies in sedimentary rocks. 3. Residual deposits occurring in unconsolidated material formed by the weathering of preexisting rocks. The geologic characteristics of each type of deposit are of fundamental importance to the successful search, development, and economic use of barite deposits.

Jan 1, 1980

By J. S. McEwan

This paper describes the derivation of a set of simultaneous algebraic equations that can be solved to produce a rigorous theoretical mass balance around solution mining wells. This mass balance can then be compared with a mass balance calculated from field measurements to provide the percentage of mass balance closure. Significant deviations from the closure can be an indication that the wells are either gaining or losing circulation fluids. The equations also provide calculations for the amount of water and dissolved mineral that accumulates in the well during the mining process, as well as the net mining rate. Equations for both single mineral mining and multiple mineral mining are discussed. They can easily be formatted into spread sheets for rapid calculation of field measurement data.

Jan 1, 2010

By C. Pattenden

The viability, self-reliance and resilience of small communities are perennial challenges in regional Australia. Recent developments in Australian mining regions seek to govern the minerals industry in a more holistic way that contributes to sustainable futures for affected communities in different contexts. In some areas of the State of Queensland land use conflicts and the cumulative impacts of multiple projects and activities across time and space have come to the fore. In more isolated regions of Western Australia the dominant issues relate to overstretching people, infrastructure and services in predominantly mining towns. In both cases, there is an ambition for regional towns with a strong extractive industry presence to transition into desirable, liveable and affordable cities with a diversified economy. The paper analyses two strategies - the Pilbara Plan in Western Australia, and the Sustainable Resource Communities Policy in Queensland - to identify how these governance instruments are contributing to sustainable development.

Jan 1, 2011

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification (nickel, cobalt, copper, and manganese) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte, ammoniacal leaching (gas reduction or Cuprion), and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stems from the 1970s and 1980s and is not always easily accessible. This paper will detail the series of tests conducted and provide updated results obtained (high Ni/Co/Cu recovery with limited Mn/Fe), as well as comment on the potential treatment options on the product solution and residue.

Feb 1, 2025

By M. Y. Fisekci

Subsidence measurement methods, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada are described. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suited methods for our conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the network of laser surveying over the workings of the new hydraulic mine. The site particulars and the mining method of the concerned area have been described briefly. The observation over the old hydraulic mine indicate that panels adjacent to each other do not obey identical subsidence phenomenon.

Jan 1, 1982

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987

By Gregory Owen Lewis, Mark William Johns

The use of resin-in-pulp (RIP) to recover dissolved metal ions from slurries is receiving increasing attention. A number of engineering aspects have been identified as crucial if a RIP sys­tem is to operate efficiently. These are the mixing of the resin and pulp, the transportation of the resin and pulp and the sepa­ration of the resin from the pulp medium. Evaluation of numer­ous alternatives revealed that air agitation is the most suitable means of mixing to effect uniform distribution of the adsorbent and to effect a high mass transfer rate, airlift pumps are the most effective method of transporting the slurry particularly as they are characterized by a low degree of resin degradation and sieve bends are the most suited means of effecting the resin/pulp sep­aration. This paper details the design of the reactor that incorporates the three identified unit operations and presents data obtained from the contactor when operated at a throughput of I 00 000 t/m. The airlift pump was found to be sensitive to pulp density and submergence ratio. The screening ability of the sieve bend was influenced by resin and the pulp density . The reactor is a cost effective, metallurgically efficient unit for the recovery of metal ions from high density slurries.

Jan 1, 1996