Search Documents

By R. N. Edwards

The Magnetometsic Resistivity (MMR) method is based on the measurement of the low-level, low-frequency magnetic fields associated with non-inductive current flow in the earth. The traditional resistivity method maps the electrical properties of the earth by measuring the electric field caused by galvanic current flow between a pair of current electrodes. The MMR method differs from it in that the potential electrodes are replaced by a sensitive coil or magnetometer and a component of the magnetic field due to the current flow is recorded. The presence of an inhomogeneity redistributes the current flow which results in a perturbation of the electric field and, usually, of the magnetic field. The electric field immediately above a relatively conductive inhomogeneity must, by Ohm's Law, be smaller than that expected for a uniform earth. The current density in this region is also reduced but the current density within the inhomogeneity itself is enhanced so that the horizontal component of the magnetic field measured above the inhomogeneity is usually larger than that expected for a uniform earth. A method of interpretation using the magnetic anomaly was patented by Jakoskyl in 1933 but it met with little success at that time. Part of the problem was undoubtedly with the instrumentation, and only recently have robust instruments of sufficient sensitivity been developed2 and field data of good quality obtained. There are many common configurations of the potential and current electrodes in the resistivity method. Similarly, in the MMR method one or both current electrodes may be moved with the magnetometer, either horizontally or vertically ( in a bore-hole), or the current electrodes may be maintained in fixed positions and the magnetometer alone moved. The MMR anomaly is defined as the difference between the

Jan 1, 1975

By A. K. Sinha

Ever since electricity was introduced, electrical injuries and electrocutions have continued to occur regularly in coal mines. An analysis of the two hundred cases of electrocutions which occurred during 1956 to 1970 indicated that over 50 percent of the incidents were caused by the ineffectiveness or lack of electrical grounding. Research shows that various types of arbitrarily designed ground beds are in use and that the ground resistance and current are often very high and subject to wide seasonal variations. The results of a recent research are discussed in this paper.

Jan 1, 1980

By W. Moser

During the ten year span from 1978 to 1987, the number of fires which occurred in under-ground coal mines doubled from the previous ten years. Anyone involved with underground coal mines is well aware of the associated tragedy that can result from these fires, both to personnel and to property. Every day mine management and mining personnel face this threat of a possible mine disaster or fire. Their ability to deal with such a situation safely and effectively depends on the level of emergency preparation developed and maintained. As a direct result of the ever-increasing interest in the Mine Emergency Preparedness Program and the Mine Fire Training Programs currently being conducted, the Emergency Preparedness Center was created. As a branch of the Mining Extension Service at West Virginia University, the Center provides preparedness training at several different levels on a varying range of topics. Classes are conducted at a new especially-designed training laboratory at the National Mine Safety & Health Academy in West Virginia. By maintaining the proper equipment and levels of training allowing for immediate response, the personnel who are part of the Center believe that the impact of a mine fire or other such emergency situation can be minimized. This paper will present recommendations for maintaining an efficient mine emergency preparedness program and will provide information regarding the Mine Fire Training Program as conducted by the Emergency Preparedness Center and describe the advantages of the newly constructed training facility.

Jan 1, 1993

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By Clayton V. Deutsch

Indicator Kriging (IK) is being commonly applied to mineral resource assessment problems. More recently, indicator simulation has also been used for sensitivity analysis and difficult change of support problems. The essential theory underlying indicator geostatistics has not changed since its introduction 10 years ago; however, the last decade has produced many important developments in its implementation. The objective of this paper is to consider some of the more important implementation details. Examples from the Porgera gold deposit in Papua New Guinea are used to illustrate the steps in an indicator geostatistical study and the importance of various implementation decisions. Specifically, in many precious metals deposits the continuity of the grades is typically quite anisotropic. This anisotropy varies in both magnitude and direction throughout the deposit. Building a model of this anisotropy can considerably improve the local kriged or simulated points. One approach to build this model is presented. In addition, there is typically more than one mineralization style and geological rock type; the spatial character of the mineralization can be quite different within each geological rock type. The rational treatment of anisotropy and geological subdivisions is common to all mineral resource assessment procedures; the importance of this qualitative geological information is not diminished with more sophisticated techniques such as indicator kriging. This paper presents an overdue comprehensive look at the practical aspects of indicator methodology. Many of the techniques and procedures documented in this paper have been developed during the course of detailed mine feasibility studies.

Jan 1, 1992

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida and Western phosphate process tailings. Physical, mineralogical, and surface characteristics were determined for both types of samples. The flocculation tests investigated dispersant and flocculant types and doses, pH, and slurry percent solids, while other parameters were held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. In single-stage tests, flocculants having low to medium anionic character effectively upgraded products at moderately elevated pH. Multiple-stage tests, and tests in which flocculants of lower molecular weight were used as site-blockers, gave improved results.

Jan 1, 2002

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By William M. Gleason

Hard times continued to plague the industry when the calendar rolled over to 2000. During 1999, the United States economy had grown vigorously, capping the longest economic expansion in United States history. However, the mining industry was not so fortunate. Commodity prices remained in a slump in the “new-economy” that was fueled by excitement and speculation about the power of the Internet during the infancy of the Information Age. Much of the investment money that once went to mining and exploration was now headed to the world of virtual gold mines. SME President Donald E. Ranta implemented new technology into his plans for SME. His two major goals were new membership growth and to foster the establishment of the comprehensive Internet presence for the Society’s technical information. His strategic priorities included enhancing the quality and quantity of publications, programs, meetings and short courses. “The Internet is the vehicle that will advance the priorities,” he said.

Jan 1, 2007

By Jacques B. Wertz

Recurring movements remotely connected with the Murray fracture zone and the San Andreas fault complex, together with the slow northwestward drift affecting the Baja California peninsula, could progressively have accentuated the tensional situation already connected with the anticlinorium in southern Arizona. From the fragmentary data gathered on the Texas lineament, it appears that a very mild curvature, concave to the northeast, may be present along this belt throughout Arizona. Those localities where the successive changes in direc¬tion of the strands of the lineament belt seem to occur do generally coincide with intersections of both north-northwestern and northeastern breaks. It is along the outward, southern fringe of the belt (at such structural centers like Bisbee, Baboquivari, Ajo) that the greatest impact of regional movements could be expected to have occurred through tangential-torsional stresses. Although it si accepted that the north-northwestern and more particu¬larly the northeastern fractures in Southeast Arizona are propitious to or partially responsible for mineralization, it seems undeniable that the Texas lineament belt must have greatly increased the potentialities for ore throughout the Arizona copper province. While intrusive bodies occur near major intersections, with the Texas lineament belt as a common denominator, it seems, the ore deposits are to be found close to one of the intrusive stocks, varying in distance from contiguity (Bisbee) to one or two miles away (Silver Bell orebodies).

Jan 1, 1970

By R. Hogg, S. Chander

An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example, in development of new processes, plant and process design, plant control, problem solving, etc.

Jan 1, 1987

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

To reduce the environmental footprint of hydrometallurgical processing of black mass from spent lithium-ion batteries (LIBs), a green leaching system based on glycine and sodium metabisulfite (Gly-SMS) was proposed. The leaching study demonstrated that the highest cobalt and lithium recoveries of 100 percent and 99.8 percent were achieved under optimal conditions. The leaching mechanism revealed that the dissolution of LiCoO2 in the Gly-SMS solution followed the shrinking core model. The apparent activation energies for cobalt and lithium were determined as 48.05 and 41.51 kJ/mol, respectively, indicating a surface chemical reaction controlling mechanism. The leachate was then processed by an acidification- precipitation technique with oxalic acid as the precipitant to remove cobalt. Glycine complexes with metal ions by zwitterionic ligand and recycles in the leaching-precipitation circuit, reducing the reagent cost. Compared to other studies, this leaching system has near-neutral operating conditions and is cost-effective, making it an economically viable alternative for treating cathode materials from spent LIBs.

Dec 1, 2024

By V. E. Chrapunov, T. V. Chnyrenkova, R. A. Isakova, V. A. Luganov

Arsenic-gold bearing ores are used as a flux in smelting or leached out to extract gold. To decrease arsenic content in processed materials and to break up the lattice to free the gold, raw materials are roasted. This article analyses the results of laboratory and pilot testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum arsenic is sublimated into elemental and sulfide forms. The process allows to minimize the negative influence on the environment but requires costly engineering solutions. Roasting in a neutral medium or with limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and may be carried out in the autogeneous mode in fluid bed furnaces. If oxidizing roasting of the concentrates is done in the presence of soda, practically all arsenic and sulfur form water-soluble compounds and remain in cinder.

Jan 1, 2002

By C. Ford, R. E. Salas Rojas, J. P. Contreras Rodriquez, S. A. Pierce

Heightened environmental consciousness has resulted in the development of various international accords dealing with natural resource management. This international awareness is now being translated into regional and local initiatives that proactively implement collaborative environmental management programs. One such program was recently initiated in northern Chile in recognition of the interconnection of Andean salars. Cooperative efforts between industry, governmental agencies and academic professionals have resulted in the implementation of simultaneous environmental monitoring of flora and fauna in the salars of northern Chile. This coordinated effort is leading to an improved understanding of the migratory patterns of South American fauna, as well as improved access to an expanded database for the multiple user groups associated with the Andean salars. The El Abra Mine is actively participating in these coordinated monitoring efforts.

Jan 1, 1999

By J. Hunter, E. Jackson

This paper describes work done by Placer Dome Technical Services Limited, a subsidiary of Barrick Gold, and Nautilus Minerals Inc. in support of the conceptual design of a subsea mining system. It describes an overall concept design plus specific studies into mechanical excavation at depth. The concept design includes one or more subsea excavators connected to a suction riser, which transports the cut material to a shipboard dewatering and offloading system. A multi-phase investigation was performed into the mechanical excavation of seafloor massive sulphides at depths of around 1600m. Rock samples were recovered and tested for rock properties and cutting behaviour. A small pick drum cutter was procured and tested on a representative concrete slab in a lab and tested again while submerged in a test tank. Finally the cutter was tested on a massive sulphide ore body at 1600m depth. The cutting performance results, e.g. pick forces and specific energies, should provide valuable input to the design of future full scale subsea mining systems.

Jan 1, 2007

By O. E. Wheeler

The use of the walking dragline as a stripping tool has increased dramatically in the past two decades. The reasons for its increased popularity and some historical background on its introduction into the mines are given in a recent paper by Learmont. (l)* The history need not be recounted here except to show the trend to longer booms which has accompanied the growth in machine size. Figure 1 shows the change in maximum operating radius on Bucyrus-Erie machines which has occurred over the years and Figure 2 shows the corresponding change in maximum boom lengths. Reference 1 also presents some of the reasons for expecting this trend to longer booms to continue. There are many design parameters affected by the increase in boom lengths; swing power, hoist and drag rope lengths, and drum capacity, to list just a few. The purpose of this paper is to discuss only the structural implications of using longer booms. As in the design of any structure, the various facets of boom design are interrelated and a process of optimization between them must be worked out either by evolution or by conscious iterative effort. The decisions we have reached about such things as material selection, structural arrangement, and applicable criteria, have not come into being overnight but represent instead many years of design experience and a fair amount of recent concentrated analytical effort. In the following pages an attempt will be made to first, state those decisions, second, explain how we arrived at that particular result; and third, describe what we expect future developments to be which might influence us to change those decisions.

Jan 1, 1976

The mineral sands industry is oriented primarily toward the supply of titanium (Ti) raw materials (titanium feedstocks) for the production of titanium dioxide (TiO2) pigment and titanium metal. Titanium minerals ilmenite, rutile and leucoxene, and titanium slag and synthetic rutile are all used principally as feedstocks for the production of white TiO2 pigment. It accounts for almost 90 percent of the world?s consumption of titanium minerals. The remainder is used for the production of titanium metal, fluxes for welding rods and as a metallurgical flux in iron and steel making. Titanium dioxide pigment is produced by two alternative process routes, the sulfate process or chloride process. The bulk of the world?s titanium dioxide is derived from the mineral ilmenite, which also contains iron oxide and other minor impurities. At some mining operations, the iron present in ilmenite is removed (ilmenite beneficiation) to produce a high TiO2 feedstock (slag or synthetic rutile) typically containing between 80 percent and 95 percent TiO2. Pigment producers then further process it to produce pigment.

Jan 1, 2011

By Frank F. Aplan, Edward C. Jr. Dowling, Richard R. Klimpel

Thirteen kinetic models that mathematically describe the flotation process have been statistically evaluated for the flotation of copper, lead and zinc ores. Comparisons have been made for a variety of circuits involving roughing, cleaning, scavenging and regrind followed by cleaning. Variations in collectors, frothers, depressants and activators have been considered. Based on the statistical criteria used for the evaluation, and the reagent, circuit and ore variations studied, the most reliable flotation models have been identified and subsequently used to characterize the metallurgical results.

Jan 1, 1986

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By Hugo J. Garcia, M. C. Fuerstenau, D. M. Lupan, J. L. Hendrix

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. The anaerobic cyanide biodegradation showed good, short-term removal of cyanide in the presence of nutrients (medium A). This system retained metabolic activity at cyanide concentrations up to 300 ppm at pH 10.5. Microscopic examination of stained specimens revealed that the bacteria were Gram-negative, rod-shaped bacilli. Strains capable of cyanide decomposition were identified as Pseudomonas and Alcaligenes. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. Studies with Na14CN showed that 17 % of 14C transformation went into the cells, 18 % into carbonate and 47 % into bicarbonate.

Jan 1, 1995

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012