Search Documents

By Daniel P. Farjeat, Hector A. Canseco, Juan M. Schmitter

Since the early sixties, tunneling in the soft clay of Mexico City, has been done with the aid of open face shields and recently with compressed air. The use of pressurized shafts up to 1.5 kilograms per square centimeter, (147 kilo pascals) with vertical locks to launch the shields, have been used in two cases. After advancing almost 200 meters of tunnel, the same vertical locks were transformed into horizontal locks, to continue the work. Due to the high decompression times involved, it was necessary to install long locks, using the tunnel itself as part of the system. This article describes those cases.

Jan 1, 1981

By C. McAllister, D. Preece, J. Berendzen

"The Multiple Blasthole Fragmentation (MBF) model models multiple explosive charge contributions and the effect on fragmentation of delay timing with its associated scatter for each blasthole. The model uses near-field blast vibration attenuation parameters and the ground p-wave velocity as inputs for part of the in situ rock property to model rock fragmentation. It models most blast design parameters explicitly and simulates the effect of wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges within a blasthole or among blastholes. The fragmentation size is calculated at three-dimensional grid points within a blast, and the fines and oversized blocks are treated explicitly. The model takes a surveyed irregular geometry of the free face of a blast as the calculation boundary.This paper presents a case study on applying the MBF model at an openpit mine. Near-field vibration measurements from signature hole blasts were conducted to obtain the stress-wave magnitude and attenuation parameters as well as ground sonic velocity. A production blast was then monitored with the corresponding fragmentation measured, serving as site-specific inputs to the MBF model. Various blast design scenarios were then simulated to develop ones that provide better fragmentation to improve mill throughput for the mine. IntroductionThe semiempirical fragmentation models currently found in the literature (Cunningham, 1987; Lownds, 1995) cannot explicitly model contributions from multiple blastholes with varying delay intervals. Most of these models are not three-dimensional. Furthermore, these models predict an average fragmentation size within a volume surrounding a blasthole and use the average size to generate a size distribution over the volume. The percentage of fines and oversize blocks is included in the distribution. Typically, such models are inadequate for predicting fines and oversize blocks (Cunningham, 1987)."

Oct 1, 2016

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By C. A. Young, J. D. Miller

Thermodynamic data has been obtained for oleate chemisorption at fluorite (CaF2) and calcite (CaCO3) surfaces using adsorption isotherms determined previously at room and elevated temperatures by in-situ Fourier transform infrared/internal reflection spectroscopy (FT-IR/IRS). Linear regression analysis was used to statistically derive free energy data as a function of temperature assuming oleate chemisorption followed Langmuir-type adsorption. Enthalpy and entropy changes were subsequently ascertained from the Clausius-Clapeyron equation and fundamental thermodynamic relationships. Essentially, no difference in the free energy of chemisorption at the two mineral surfaces was found; however, the differences in enthalpy and entropy values were significant. By comparison, the results showed that oleate chemisorption at fluorite surfaces was more extensive and more entropically driven due to more water being displaced. Results correlate well with values determined in the literature for other mineral collector systems. These findings help explain the greater hydrophobic character of fluorite than calcite in both the absence and presence of oleate.

Jan 1, 2002

By Paul Gribbon, Julius Strid, Greg Colzani, Jim McDonald

Portland, Oregon’s $370 million West Side Combined Sewer Overflow Tunnel Project has completed the final phase of construction and commissioning. The construction contract, which began in September 2002, was a reimbursable cost plus fixed fee contract that followed a qualifications-based contractor procurement process and apre-construction planning phase. This paper addresses the final results of the contracting method and provides a lessons-learned case history. Specific items addressed include the benefits realized from the contracting method, areas of improvement, final costs compared to the original contract estimates, design changes and schedule impacts, and subcontract management issues.

Jan 1, 2007

By A. Porvali, V. Agarwal, M. Lundström

Hydrometallurgical recovery of rare earth elements (REE) from NiMH battery waste can be performed using sulfuric acid leaching followed by selective precipitation as double salt (REENa(SO4)2•H2O) by adding Na2SO4 as a precipitating agent. The formed double salts can be treated further with NaOH solution to form REE hydroxides. This study focuses on metamodeling of a simulated flowsheet with design of experiments (DOE). Based on literature survey, a process flowsheet was developed using HSC Sim software. The created flowsheet focuses on circulation of solution containing Na+, K+, SO42- ions and impurities liberated in the NaOH treatment of double salt precipitate. The effect of seven parameters (P1-P7) on seven responses (R1-R7) were modeled using central composite design (CCD). INTRODUCTION Nickel metal hydride (NiMH) battery waste can be considered as an urban mineral due to the presence of valuable metals like: Ni, Co and rare earth elements (REE) (Larsson et al., 2013). In NiMH battery waste leaching experiments, sulfuric acid has often been employed as a lixiviant (Pietrelli et al., 2002,Zhang et al., 1999,Rodrigues and Mansur, 2010,Porvali et al., 2018). The key advantages of sulfuric acid are its stability and cost-effectiveness compared to other mineral acids such as HCl and HNO3. However, the usage of sulfuric acid in NiMH battery waste leaching poses simultaneous challenges and advantages. Limited REE solubility can be taken as benefit when recovering REEs double sulfates after solid-liquid separation. However, sodium and potassium hydroxide, present in electrolyte residues in the battery waste, can cause in-situ precipitation already during leaching due to limited solubility, thus decreasing the total REE recovery (Porvali et al., 2018). However, this problem can be circumvented by washing the electrolyte residues off the raw materials. Subsequently, the REEs may be precipitated in bulk as a mixed double salt out from the solution at very low pH with minimal co-precipitation of Ni and other metals. This relatively easy separation method can be extremely advantageous in the case of such a complex solution matrix with relatively high REE concentrations (conc.). Once REEs have been precipitated as double sulfates as per eq. (1) (Porvali et al., 2018), the resulting double salt precipitate lacks applications without further treatment. Direct thermal treatment would generate sulfur dioxide emissions and likely require high temperatures in order to transform double sulfates into REE oxides. Furthermore, the precipitate contains Na ions, which would need to be removed by chemical treatment from the calcined REE product. In the context of circularity of raw materials, it can be taken of a remarkable benefit if the sodium and sulfur present in the double salt could be reused instead of wasting them into the side streams. To that end, in this simulation study, the double salts are converted by dissolution and precipitation to hydroxides which are readily treatable, e.g. with total dissolution and solvent extraction, for further purification (Abreu and Morais, 2010):

Jan 1, 2019

By J. P. Morgan

The Vesta Preparation Plant of the Jones & Laughlin Steel Corporation is located on the Monongahela River, eight miles south of Brownsville, Pennsylvania. This plant is capable of cleaning 2400 NT/hr of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables. handle the -1/4" fraction of the raw coal feed. Cleaned -coal goes to boot classifiers where the +48 mesh material settles and is removed by bucket elevators. This 1/4 x 48 mesh material is then sent to centrifugal driers for dewatering. As designed, the minus 48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and dewatered by filtration. The-products of the heavy media circuit, the launder-table-boot-drier circuit and the cyclone-thickener-filter circuit are combined to constitute the shipped metallurgical coal. This Vesta-Shannopin mix is combined at J&L's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke.

Jan 1, 1962

By Cheng Ang, Yun Bai, Zhi Liu

"This paper presents a conceptual design of an innovative tunnelling method named the Ring Pipe Jacking Method (RPJ) which is conducted by the Ring Pipe Jacking Machine (RPJM). The RPJM consists of a double ring shell which forms a ring section where small interlaced cutter heads or several micro tunnelling machines are assembled to cut soil. Similar to the conventional pipe jacking method, the RPJM also needs a thrust system, a slurry transport system, and a control system. To satisfy the need for large/super large or special section tunnels in future, the RPJM is designed to reduce sharply the excavation face to the annular section, thus enhancing the face stability. Part of the innovation is that the RPJM uses modular cutter heads or micro-TBMs which can be reused. The typical double shield shape can be easily changed by reinstalling the modular cutter heads. Modularity allows the tunnel to be cut in any cross-section shapes, ranging from a circular tunnel to a rectangular one. INTRODUCTION The demand and requirement to utilize urban underground space is rising with the rapid social development in recent years. It is necessary to reduce excavations of the urban ground surface to ensure smooth traffic in cities. Therefore the conventional open cut construction method for underground tunnels can no longer satisfy the need of practical engineering, and it is taken over by trenchless technologies .The Pipe jacking method is an important trenchless technology and is used more and more frequently to install underground pipelines, but the present pipe jacking method still has many problems. For example, it is not suitable for installing large-diameter tunnels and it also has difficulty in construction of short radius curved tunnels. This paper presents a conceptual design of an innovative pipe jacking machine named the Ring Pipe Jacking machine (RPJM) and introduces the correspondent Ring Pipe Jacking Method (RPJ) which can be applied to construct large-diameter tunnels. Furthermore, technical characteristics and superiority of the ring pipe jacking method are analyzed in this paper."

Jan 1, 2016

"INTRODUCTION The characterization of groundwater hydrogeology is a common component in feasibility studies, geotechnical investigations and regulatory permitting for mining operations. The lithology at a location of interest may include several discrete water-bearing units; and the means of isolating each for testing can be accomplished through the use of inflatable packers. Consideration for testing during drilling program planning and communication between all stakeholders is essential to ensure that the Mine, Drilling Contractor and Hydrogeological Testing Specialist (Specialist) are ready to perform packer testing when the call is made to mobilize. Often, the notice to mobilize can be delayed and then occur with little warning due to the issues that can occur during drilling of very deep boreholes, as well as other factors. Hydrogeological investigation reports and journal articles generally discuss testing methods and results, with limited information available describing the planning and coordination of the field testing program, as evidenced by the lack of references cited below. The source of inspiration for the subject matter of this paper is grounded in the author’s past shortsightedness; with the hope that others not share similar misfortunes but experience success through thorough preparation for their future hydrogeological testing programs. The sections below focus on the planning stages of a field investigation using inflatable packers, including considerations for site specific conditions, designation of stakeholder responsibilities, and communication of testing expectations. Following these sections is a presentation of two examples of successful field programs and lessons learned in addressing problems encountered along the way. PRELIMINARY PROGRAM PLANNING & CONSIDERATIONS From the onset of planning for drilling programs, the Specialist should be in communication with the Mine to review plans and identify fatal flaws which could impede collection of hydrogeological data. Preliminary scope decisions can significantly affect the budget and duration of hydrogeological field programs and may dictate the means by which the field data is collected. The issues that need to be considered include the following factors. Testing Objectives The setup of the packer tool is dependent on the testing objectives. Is the goal to estimate bulk aquifer hydraulic conductivity or to identify discrete discontinuity hydraulic characteristics? Are groundwater samples needed? The answers to these questions affect selection of test interval length and what instrumentation might need to piggyback on the packer tool. Identifying the testing goals initially will provide adequate time to prepare packer equipment for mobilization. Borehole Size While inflatable packers come in many shapes and sizes, some sizes are more readily available and easier to procure on short notice. Packers for NQ and HQ size boreholes have been historically easy to procure and are commonly used in exploration drilling. Packer equipment is available for smaller holes, but it becomes more difficult to fit instrumentation down-hole as the borehole size decreases. This is particularly a consideration if collection of groundwater samples is required. In addition, risks of losing the hole or equipment downhole are greater for smaller boreholes. Larger boreholes require larger packers and clearly require more effort and heavier capacity machinery to manually manipulate due to the increased size."

Jan 1, 2017

By Gene R. Block

The most economical method of reclaiming land that has been mined, whether it be in urban areas or in rural areas, is when the final configuration of the mining area is that which is required by the subsequent use. Surprisingly, there are a number of examples of this situation. In the arid southwest where water production for the expanding population is a problem, many urban sand & gravel excavation areas subsequently serve as holding basins for ground water recharge. In other areas of the county where water is not in short supply, sand and gravel excavations can be planned in such a way that subsequent land uses such as parks and homesites can be enhanced by utilizing the excavated areas as a water amenity. Reclaiming land for agriculture is another example of utilizing the excavated area for a subsequent use providing the excavated area has not been mined too deep. Other than replacing the layer of topsoil on the excavated area, the final configuration of the mining area is in many cases ready for the subsequent agricultural use.

Jan 1, 1984

By Ahmet Gursoy

Maryland, will be the widest vehicular tunnel ever built by the trench tube method. Careful coordination and planning were required to meet the tight and fast design and construction schedules. During the preliminary design, traditional design drawings were bypassed in favor of 25 preliminary design reports representing major work breakdown structures (tasks). For each task, alternative design solutions were examined and analyzed by means of trade-off studies on the basis of engineering, constructibility, and economic considerations, thus providing an overall conceptual value engineering approach for the entire project. So far, total value engineering proposed by the contractor for Contract I I (largest contract of the project at $245 million) is less than 1.5 percent of the contract value. This is an important indication of the success of the design phase planning.

Jan 1, 1983

By John Batty, Rennie Stallknecht, Dave Dew, Rennie Marais

GENCOR was contracted by Lonrho Plc of London to design a treatment plant for the benificiation of ores from the Amantaytau Goldfields in Uzbekistan (CIS). The testwork required for determining the design parameters was conducted at GENCOR Process Research in Randburg South Africa, on large bulk samples of ore shipped from the CIS. The initial milling and flotation testwork was designed to both optimise the conditions for maximum gold recovery, and to provide flotation concentrate for subsequent testwork. The concentrate produced was fed to a pilot scale BIOX® plant, and at the client's request a portion was shipped to specialists in roasting and pressure oxidation technology for comparison. Besides the testwork conducted at the GENCOR Process Research Laboratories in South Africa, the client also requested that the testwork be repeated at the Ingichki Research centre in Uzbekistan to demonstrate to their CIS joint venture partners that the results obtained in South Africa are reproducible and to demonstrate the ease of operation of a BIOX® plant. Pilot scale equipment was air freighted to Ingichki where the results of the testwork obtained in South Africa were successfully duplicated. BIOX® technology was shown to achieve higher gold recoveries than either roasting, whole ore roasting or pressure oxidation.

Jan 1, 1995

By J. R. Hurley

The continuous flow, horizontal drum blender has dynamic properties which may be described by the same type of equations which often arise in electrical filter analysis. Furthermore, the equations may be readily solved by the same techniques used in electrical control analysis. For this reason the blender model developed is termed an "Electric Analog", although strictly speaking it is a mathematical model. Presentation of the dynamic performance of the blender as an electrical (or mathematical) model is desirable for several reasons. The model can be of assistance in correlating performance data with equipment design parameters. The model 'can be used with other process equipment models for simulation of an entire plant operation or in stability studies. In addition, the model may be useful in providing insight into the actual blending mechanism, or it may suggest a similar method of analysis for other closely allied equipment.

Jan 1, 1967

By R. K. Rajamani

The theoretical model based on fluid mechanics, in conjunction with the laser-Doppler velocimetry (LDV) measurements, elucidate the size-classification mechanisms in an industrial hydrocyclone. The model has no adjustable parameters and involves solving the Navier-Stokes equations to predict the liquid-phase velocities. The spatial-concentration gradients were determined considering the particle phase in the Lagrangian frame and the classification curve was determined by balancing the forces acting on the particle. The force balance requires liquid velocities, which in turn depend on the local volumetric concentration of the particles. Hence, complete modeling work involves coupling both the concentration and liquid-phase velocity calculations until convergence is reached. Finally, the experimental and predicted classification curves were presented for 250-mm hydrocyclone operating at high-percent solids.

Jan 1, 1994

By M. F. Martin

Dewatering aids are chemicals which enhance the efficiency of mechanical dewatering equipment such as vacuum disc filters and centrifugal dryers. A new dewatering aid has been developed which significantly lowers the moisture content of the mineral concentrate and causes none of the undesirable side effects normally associated with dewatering aids. Highlights of product development from laboratory screening through field testing will be discussed.

Jan 1, 1985

By Bill Morgan

This paper discusses the economic zones of application for several different types of earthmoving equipment: dozers, wheel loaders in load-and-carry applications, wheel tractor scrapers, articulated trucks, rigid-frame trucks and wagons. Only the medium to large pieces of equipment were considered. From this chart (Figure 1), you can see the size range, in tons of carrying capacity, of Caterpillar equipment and the specific models analyzed.

Jan 1, 1994

By Alexander May

In its role of providing technology to promote the efficient use of minerals and mineral process waste, the U.S. Bureau of Mines has conducted research at: its Tuscaloosa Research Center to identify and develop high volume uses for phosphogypsum. Mixtures containing a maximum of 50 percent phosphogypsum, 6 to 10 percent lime, and the remainder fly ash had compressive strengths as high as 4,800 psi. The effects of the mounts of phosphogypsum, lime, and fly ash were investigated. Also, the effects of fly ash to lime ratios were studied.

Jan 1, 1983

By Yao Zhou

Under the United Nations Convention on the Law of the Sea (UNCLOS), the international seabed area (Area) and its resources are the common heritage of humanity (CHH). Patent rights can be incompatible with the CHH doctrine and its underlying principles because patent holders might charge unjustifiably high prices to license patented technology for exploring and exploiting the Area’s resources (creating a "patent holdup" situation), might choose not to license, or might license exclusively when doing so would contravene CHH principles. However, a reasonable patent licensing regime can contribute to sharing the benefits derived from the Area and promote environmental sustainability. Provisions of the UNCLOS that stipulated compulsory technology and financial transfers were removed in the 1994 Agreement relating to the Implementation of Part XI of the UNCLOS (1994 Agreement), but to promote equity and sustainability I propose a voluntary licensing regime modeled on the concept of reasonable and non-discriminatory patent licensing (RAND) that has been used in other contexts. The International Seabed Authority (ISA) or another entity will need to coordinate and promote this licensing regime through governance of intellectual property (IP) derived from the Area. This proposed approach can better effectuate the CHH doctrine and its underlying principles.

Sep 1, 2014

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

Smart defense: that?s what the industry needs to play for the next four years, according to panelists at the 118th Annual Meeting of the Northwest Mining Association (NWMA), which met December 2-7 in Spokane, WA. The conference was well attended, with approximately 2,200 attendees, 244 booths in the two packed exhibition halls, and a rich offering of short courses, field trips, social events and technical sessions. Speakers at the packed legislative session articulated many of the frustrations felt by members of the mining community after the U.S. elections in November, and offered words of advice. Matthew Ellsworth, the new Government Affairs hire at NWMA, stated it best: ?Elections are like Christmas: you find out who?s naughty and nice ? and it?s always going to come again.?

Jan 1, 2013