Search Documents

By J. B. Yianatos

This paper addresses the impact on performance of column height (H), and column height to diameter (H/D) ratio by modelling the effect of HID on mixing and consequently on recovery and grade. Mineral recovery increases with increasing H/D ratio for a constant column volume and feed flowrate, while the concentrate grade decreases to a minor extent. Columns 10-15m in height with H/D-10 are well suited for feed rates 150-600 L/min. Maximum H/D is determined by the gas carrying capacity, an important consideration for pilot units where H/D?200.

Jan 1, 1987

By Carlo Grandori

Foreword In loose ground and soft rock formations, mechanical tunnel boring is necessarily dependent on the adoption of shield machines and the application of adequate support or lining structures. These structures are erected either within or immediately behind the rear portion of the shield and provide the required reaction to the forward thrust. In competent rock formations where systematic support is not a requirement, hard rock tunnel boring machines generally advance by thrusting from a structure gripped against the tunnel walls. These machines may feature a more or less extended cutterhead shield or roof support, but when in weathered, fractured or otherwise weakened ground, or in fault zones filled with soft gouge, the gripper mechanism often cannot provide enough thrust reaction to advance the cutterhead. Under these conditions, early support of the arch and walls is generally required in the form of rock bolts, steel rings and laggings and some times of a primary concrete lining placed in the short section between cutterhead and grippers. Such tunnel support measures generally fail to produce an adequate increase in thrust reaction capacity, but

Jan 1, 1976

By C. P. Mangelsdorf, Richard A. Allwes

At the request of the U.S. Department of Labor, Mine Safety and Health Administration (MSHA), the U.S. Bureau of Mines evaluated the suitability of using tri-sets for protecting mine personnel in roof-fall prone areas. A steel-set arch provided by MSHA served as a basis for evaluating the performance of the tri- set. All tests and analyses were conducted according to the arch canopy test and design procedures developed by the Bureau. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of their experimental behavior. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri -sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that tri-sets may be considered for protection against roof falls, provided that the arch canopy design procedure is utilized for each application and that the principles underlying the design procedure are understood.

Jan 1, 1992

By J. Lovering, H. Wilhelm, P. Siewert

Introduction The Afton property is located 290 km (180 miles) by air east-northeast from Vancouver and 14 km (8.7 miles) west of Kamloops, a city of 60,000 people, in south central British Columbia, Canada. The mine is adjacent to the Trans-Canada Highway at an elevation of 670 m (2198 ft) above sea level. The ore body is a porphyry copper deposit that has undergone supergene alteration. The major economic minerals in the supergene zone are native copper and chalcocite with chalcopyrite and bornite in the hypergene areas. The grade is 1% with an overall copper distribution - 70% native, 25% chalcocite, and 5% chalcopyrite with bornite and covellite. The ore also contains important but variable amounts of gold and silver. The mill was designed to treat 6350 t/d (7000 stpd). Semiautogenous grinding was selected to minimize capital cost and because of the expected high clay content of the ore, which would have caused problems in a conventional crushing and screening plant. Test work indicated that a recovery of 87% was possible in a circuit incorporating both flotation and gravity separation. Flowsheet Run-of-mine ore is crushed in a 1.06 x 1.65-m (3.5 x 5.4-ft) Allis Chalmers gyratory crusher set at 228.6 mm (9 in.), closed side setting. The surge pocket, below the crusher, is emptied by a Hydrastroke feeder onto number one conveyor, which discharges onto a 180,000-t (198,416-st) coarse ore stockpile. Six Hydrastroke feeders on two conveyors withdraw the crushed material from the bottom of the pile. These two conveyors, in turn, discharge onto the belt feeding the semiautogenous mill. The live storage in the stockpile is approximately 22,000 t (24,250 st), sufficient for three days' mill feed. Primary grinding is accomplished in an 8.5-m (28-ft) diam by 3.7-m (12-ft) long Koppers (Hardinge Cascade) mill (Fig. 1) containing a 10% ball charge and driven by a 4000-kW dc variable speed motor. The mill dis¬charge is pumped by a 10 x 12 G.I.W. pump to a 1.22 x 4.88-m (4 x 16-ft) stationary screen sloped at 20°. Screen oversize returns to the semiautogenous mill (SAM), and the undersize flows by gravity to the ball mill discharge pump box. Secondary grinding is performed in a 5-m (16.4-ft) diam by 8.84-m (29-ft) Koppers overflow ball mill driven by a 3430-kW synchronous motor through an air clutch. The mill is in closed circuit with a Krebs Cyclopac containing 10 635-mm (25-in.) cyclones and the cyclone overflow, at 35% solids and 65% to 70% -200 mesh, is flotation feed. In order to limit the buildup of native copper, circulating in the secondary grinding circuit, a portion of the underflow from the cyclones is processed in a circuit containing screens, cyclones, and shaking tables to produce a finished metallic copper concentrate. Primary mill variable speed drive The overall waste to ore ratio at Afton was 4.5:1. The mining was to be done with only three shovels, which meant that it was highly unlikely that more than one of them would be in ore at any one time. The resulting inability to blend the mill feed made it impossible to prevent wide swings in the grade and grindability. The variable speed do drive motor installed on the semiautogenous mill was selected because of the extreme variability of the Afton ore body. This variability has persisted throughout the lifetime of the mine. There are times, however, when due to ore conditions, the mill is operated at full speed (78% of critical) for extended periods of several shifts duration. There are other times when the mill speed may be changed several times in a 12-hour shift due to changing ore conditions. When ore is processed that contains a fairly large proportion of fine native copper, the primary mill speed and, consequently, the tonnage may be reduced to improve the secondary grind and to maintain an acceptable grind and recovery. High clay ores require less mill speed and more dilute grinding densities. In the latter case, the slower primary mill speed also helps to minimize damage to the mill liners. Approximately 57% of the time the mill operates between 90% and 100% of full speed or between 71% and 78% of critical. The variable speed is also used for inching during mill relines.

Jan 1, 1987

By Graham Andrews

Experiment shows that the microbial degradation of pyrite does not necessarily proceed stoichiometrically. Under some conditions sulfur is oxidized preferentially leaving something approaching iron in composition; under others, the pyrite is converted almost to elemental sulfur. A kinetic model for the process based on three elementary biochemical reactions can explain these observations. The diffusion of sulfur along grain boundaries and dislocations in the solid pyrite uncouples the oxidation rates of sulfur and iron from the requirements of stoichiometry. This mechanism also explains qualitatively why bacteria adsorb preferentially at dislocation sites on pyrite surfaces, why they form "pits" at these sites, and why amorphous pyrite is more readily degraded than pure crystals. The rate-limiting step for pyrite oxidation is discussed

Jan 1, 1989

By K. Kim, T. M. Yegulalp

A new explanation of the scale dependency of rock strength is presented based on the theory of extremes. A brief review of past work on specimen size and strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect. It is shown that the weakest link theory is directly related to extremal statistics and that parameters of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1994

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

By Jerry Wang, Greg Bold, Mahmood Khwaja, Rebecca Caldon, William Simcoe

Phase III and Phase IV of the Beaver Creek Clean River Project, Albany, NY, includes microtunnel construction of 2,320 feet of 48-inch/36-inch internal diameter (ID) conveyance pipe and a 525 foot long 9.5-ft horseshoe shape roadheader excavated tunnel. Notable challenges were encountered during the construction including mixed face tunnel conditions, undocumented existing fill ground conditions that resulted in settlement during shaft construction, and unstable tunnel face conditions. This paper discusses several of the key challenges encountered during construction and selected solutions to construction sequencing and methodology to successfully complete Phase III and Phase IV of the Beaver Creek Clean River Project.

Dec 1, 2022

By J. C. Yingling, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Much of the land reclaimed since enactment of the 1977 Surface Mining Control and Reclamation Act is overcompacted. Research has shown that excessive compaction in replaced growing media is detrimental to the establishment of trees. If trees are to be grown on reclaimed surface mined sites, something must be done to alleviate this excessive compaction. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed growing media. The University of Kentucky developed test cells on reclaimed areas at a surface mine in eastern Kentucky to determine the impact of tillage (ripping) on soil compaction and tree survival rate. The ripping methods being evaluated include shallow tillage using conventional farm equipment and deep tillage using a dozer with a ripping arm. Each test cell was planted with various species of trees, and for the first two years of tree growth, data were collected at these test cells for soil dry bulk density, penetration depth and resistance, and survival rate of trees. These data were statistically correlated to determine how ripping affects the relationship between soil compaction and tree survival rate.

Jan 1, 2003

By J. B. Stockton, D. J. Robbins, E. T. Woodburn

Batch flotation data in an equilibrium cell show that beneficiation improves with froth drainage. The limiting lamella thickness in a well- drained 3-phase coal froth appears to be determined for ultra-fine particles (-45µm) by the d90 particle size. The froth stability is considered to depend on the existence of a very thin liquid film between the outer surfaces of the d90 particles and the bounding bubble interfaces of the lamella in which the particle is held. The dependence of the coalescence rate of bubbles in these froths on the residual surfactant concentration in the lamella liquid is then consistent with stability analyses for two-phase foams.

Jan 1, 1988

By P. K. Crane, S. C. Gambrell

The work reported herein compares the support characteristics of two different types of roof truss subjected to the same force in the horizontal tension member. The major differences between the two trusses are in the sequence of tensioning the horizontal and inclined members and in the design of the loading brackets. A photoelastic model was used to compare stresses at points along the roof of the mine opening and at the junction of the roof surface and the rib. The effects of simulated subsidence on stress in the roof and on tension in the horizontal member were analyzed. Results indicate that there are significant differences in the overall support characteristics of the two trusses. Conclusions are drawn relative to which type of roof truss provides the most favorable support if the horizontal members are tensioned equally.

Jan 1, 1986

By K. N. Santini

The evaporite deposit at Searles Lake consists of alternating brine-saturated saline beds and saline-bearing mud beds. Three major subsurface brine-saturated saline horizons have been identified by private companies and the U.S. Geological Survey. They have been termed, from bottom to top, the Mixed Layer, Lower Salt, and Upper Salt. The important water-soluble components (Na, K, Mg, CO3, HCO3 , SO4, Cl, and B407) are either in brines or have combined to form the following minerals: halite, hanksite, trona, nahcolite, burkeite, borax, thenardite, northupite, sulfohalite, glaserite, etc. Kerr-McGee Chemical Corp., the current operator at the lake, selectively pumps interstitial brines from each of the major horizons to feed its three chemical plants. As the pumping continues, brines are continuously replenished within the deposit by dissolution of the minerals through natural recharge or artificial fluid injection (solution mining). The brines are processed to produce a variety of chemical products, which include sodium carbonate and sulfate, potassium chloride and sulfate, sodium borate, and boric acid. The Anaconda Minerals Co. has been evalua¬ting potential domestic trona acquisition since 1981. We have evaluated various properties in the Green River, Wyoming trona district, and Owens Lake and Searles Lake in southern California. In 1983, we purchased with our joint-venture partner, Leslie Salt Co., the southern portion of Searles Lake from Occidental Petroleum Corp. Since mid-1983, Anaconda has been conduct¬ing a small exploration-drilling program at the property. The initial core holes were drilled along and adjacent to the existing access road. In 1984 we used an all-terrain drill rig to gain access to drill sites on the playa where no roads exist. The use of this equipment proved to be highly successful. The drill program consists of coring to an average depth of 450 feet and collecting brine samples from potentially commercial horizons. The brine samples are collected by setting a packer and swabbing the hole. The core is logged and split lengthwise; one-half is submitted to our Tucson Geoanalytical Laboratory for semi-quantitative mineralogy by X-ray diffraction and the following suite of chemical analyses: Na, K, Mg, C03, HCO3, SO4, Cl, B407, Li, H20 insolubles, and acid insolubles. Additional test work for selected core samples will include effective porosity and horizontal permeability determinations. The brine samples are subjected to the same suite of chemical analyses (minus insolubles) as the core samples. In addition, specific gravity is also determined. Both cross sections and isopach maps are being constructed. The hydrological characteristics of the potentially commercial horizons are also being investigated.

Jan 1, 1987

By F. M. Doyle, S. Duyvesteyn, K. Sreenivasarao

Toxic metals entering surface or ground water from sources such as metal finishing shop spills and abandoned mines can pose a significant threat to public health and the environment. Ion flotation and similar foam separation techniques show great promise for treating dilute, metal-contaminated solutions, and could also be used to treat effluents from many minerals and metallurgical processing operations prior to discharge. In ion flotation, an appropriate collector is added to the solution to form hydrophobic complexes with the metal ions. These metal-bearing species are then removed by flotation, usually with trace addition of a frother to stabilize the foam. In an effort to better understand the underlying scientific and engineering principles that determine the performance of ion flotation, the removal of Cu(II), Pb(II), Cd(II), Cr(II) and Cr(VI) has been studied using laboratory scale flotation columns in batch mode. The effects of the superficial air velocity, solution and froth height, nature of the collector, collector: metal-ion ratio, ionic strength and several frothers at low concentrations on the flotation kinetics are reported. Finally, results are presented on methods that might allow regeneration of collector and recovery of by-product metal from the foam product.

Jan 1, 1995

By John Songstead

INTRODUCTION The Bunker Hill mine, located at Kellogg, ID, in the Coeur d'Alene mining district, has been a major pro¬ducer of lead-zinc-silver ore since 1887. Since its dis¬covery, it has produced over 25 401 171 t (28 million st) of ore from 20 to 25 veins and ore zones. The mine now covers an area of approximately 1.609 km (1 mile) in length and 0.8 km (1/2 mile) in width and extends from 1097 m (3600 ft) above sea level to 488 m (1600 ft) below sea level. Production is presently at a rate of 1542 t/d (1700 stpd). During 1965, a new stoping method, the Bunker Hill pillar system, was developed to enable the profitable mining of large, low-grade zinc ore bodies. The system was specifically designed to in¬corporate the Atlas Copco T26GH rubber-tired loaders. High productivities were achieved, and the method was adapted for mining the higher grade stopes where large timber square sets are utilized. This results in nearly 100% extraction. GEOLOGY The area encompassing the Bunker Hill mine lies immediately south of the Osburn fault, a major east-west striking, deep-seated strike slip fault which is the dominant structural feature in the Coeur d'Alene district. The Bunker Hill forms a series of veins and mineralized zones which occur as link structures, tension fractures, and breccia zones in folded, interbedded argillaceous quartzites of the Revett and St. Regis formations of the Precambrian belt series. The Rosco ore body is predominantly a zinc ore body above the Cate fault, which is presently known to occur from the 13 level. [elevation 488 m (1600 ft)] to the 1600 level [elevation 304 m (1000 ft) ]. These ore bodies are stringer zones with at least one dominant 1.8 to 4.5 m (6 to 15 ft) wide band of ore. They dip 0.09 to 0.26 rad (5° to 15°) steeper than the local 0.61 rad (35°) dip of the Cate fault, and also deviate 0.26 to 0.52 rad (15° to 30°) in strike from the Cate. Because of the flat dip and fractured weak hanging wall, normal cut-and-fill mining has not proven practical in this ore body. The mechanized timber methods described in the next section and the Bunker Hill pillar system are the mining methods successfully used. MINING METHODS While pillar stoping and mechanized cut-and-fill stop¬ing methods were obviously superior to the widely used timber stoping methods, as far as cost and productivity

Jan 1, 1982

By N. S. Dalal, Xianglin Shi

Metal ions, such as chromium (Cr) and vanadium (V) are found as trace impurities in mineral dust. Since metal ion mediated free radical generation has been implicated in many disease processes, we carried out a detailed investigation of the metabolism of these metal ions by biological redox systems and the possible oxygenated radical generation therefrom. We found that highly reactive Cr(5+) species are generated in the reduction of Cr(6+) by NADPH-dependent glutathione reductase, lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase. The reduced metal ion species react with hydrogen peroxide, to generate hydroxyl (•OH) radicals in a continuous cycle. The enzymatic catalysis processes also involves the reduction of molecular oxygen to the superoxide [(0-1 2)] radical. Thus only a trace amount of metal ions chemisorbed on mineral dusts, such as quartz, can catalyze the generation of the highly toxic oxygenated radical species from cellular hydrogen peroxide, suggesting a new biochemical mechanism for mineral dust induced chronic lung injury.

Jan 1, 1991

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By S. J. Parkin, P. Shead

Extraction of coal at Harworth Colliery is undertaken in the Deep Soft seam at roughly 1000m depth where the strata temperature is 42 "C. Production employs the longwall retreating method using high powered mechanised methods to extract coal at a rate of approximately 40,000 tonnes per week from a single face. This paper describes the climatic conditions encountered on a typical district , 6's district, where the initial ventilation set-up was as a typical U-type district which was antitropally ventilated. Under this initial set-up climatic conditions in the intake typically exceeded 30 "C effective whilst in the face area and in the return airway effective temperatures in excess of 32 "C and 33 "C were common . The paper then proceeds to describe the methods employed to attempt to improve the climatic conditions on the district, especially with regard to the coal face and return airways and describes in detail the effects of reversing the district airflow direction, employing homotropal ventilation, on the climatic conditions. The results of this reversal have been dramatic and have resulted in a substantial improvement in the climatic conditions experienced , however problems have been encountered with the control of methane gas since the changeover. The final part of the paper describes the results of computer simulations to analyse the effect of various ventilation designs on the predicted climate for future production districts in order to de- fine a district layout which will produce acceptable climatic conditions in the working zone without the need to use refrigeration techniques and which will improve methane gas control .

Jan 1, 1997

By Elvin R. Beach, Jaroslaw Drelich

Pull-off forces were measured for 8-9 pm diameter polystyrene (PSI particles on smooth spin- coated polystyrene films and hexadecanethiol (HDT) self-assemble monolayer surfaces using atomic force microscopy (AFM). Three parameters were controlled during experimentation: (i) the maximum applied load pressing the particle onto the substrate was varied from 50 to 4,000 nN, (ii) loading/unloading rate for the particle to attach and separate from the substrate varied from 0.01 to 9.3 Hz, and (iii) contact time for particle to reside on the substrate surface before retracting the particle to separate it from the surface changed from I µsecond to 200 seconds. the pull-off forces increased with increasing applied loading, increasing loading/unloading rate, and increasing contact time for the PS particle on PS film and on HDT monolayer. The PS particles experience elastic and plastic deformations duringpull-08 force measurements. Plastic deformation is primarily associated with flattening of surface irregularities. The results obtained in this research suggest that the particle-substrate contact areas of the magnitude comparable to those predicted by the JKR contact mechanical model can be reached in the AFM experiments by using high applied loads and long particle-substrate contact times. This result re-opens the prospect of' using AFM for studying surface energies of deformable micro-particles, even if the micro-particles have small irregularities on the surface.

Jan 1, 2003

By Fred L. Stanley, Ricky Q. Honaker, Michael J. Mankosa

Spiral concentration has gained a great deal of popularity as a cheap, effective method for recovering fine coal (8x100 mesh). Typically, 6-turn, wide-profile spirals are used in either a single pass, open- circuit configuration or in combination with a middlings retreat circuit. Recent work conducted at Carpco, however, has indicated that a split feed scenario and/or hydraulic classification in advance of spiral concentration offers significant advantages in both capacity and metallurgical performance. In addition, it has also been shown that the apparent density separation which naturally occurs in a hydraulic classifier provides significant up-grading in terms of pyrite and ash rejection. The results from this study will be presented in comparison with those obtained from open-circuit spiral testing.

Jan 1, 1995

By George A. Takach

The U.S. Bureau of Mines is conducting research with the goal of automating underground coal mine roof bolters for greater mine safety. In the project described here, the Bureau has focused on automating the drilling portion of the drilling and bolting cycle. A drill monitoring system designed and developed by Parvus Corp. of Salt Lake City. UT, was placed on a Bureau model roof- bolting drill. The drilling parameters of torque, thrust, rotation rate, penetration rate, and position are monitored through sensors connected to an asynchronous, control-oriented local area network (LAN) that communicates with data-accumulating and data-processing nodes. By placing microprocessors at the two data nodes and at the valve control nodes, and combining these nodes with a personal computer (PC), the monitoring and control system can achieve parallel processing capabilities. Such capabilities are referred to as locally intelligent distributed processing. Only data that have changed significantly are reported through the LAN to a supervisory control and data acquisition (SCADA) system mounted on an IBM- compatible 80286 PC. The SCADA system displays the values of the drilling parameters and calculates the specific energy of drilling, which is then used as an indicator of the type of rock being drilled. Besides monitoring the drilling process, an operator at the computer can control the rotation and thrust of the drill from a remote location through the SCADA program and can set drilling parameters on the basis of observed values of the specific energy of drilling.

Jan 1, 1992