Search Documents

By Lim Thi Duong, Du Duy Bui, Thuat Ngoc Pham, Chuc Ngoc Pham, Que Anh Nguyen, Hoa Anh Bui, Chi Thi Ha Nguyen, Hoan Thanh Nguyen, Bac Quang Nguyen, Kien Trung Nguyen, Dung Trung Doan, Nhiem Ngoc Dao

The microstructures and kinetics of a rich iron ore ( TFe = 65.84%) of Na Rua mine, Vietnam, used for the iron production were investigated in this study. Thermal behaviors of iron ores were well-examined by heating microscopy, thermogravimetric analysis, and differential thermal analysis. After being pelletized and then oxidatively fired at 500–1200 °C for 2 h, the pellets fired at 1200 °C (P1200) displayed a hard and dense structure with a decent compressive strength of 317.9 kg/pellet whereas those fired at 500 °C (P500) had a soft and spongy structure. The reduction of iron pellets conducted in a flow of a 60–100% CO2/ Ar gas mixture at 900–1100 °C showed significantly higher efficiency than the reduction using coal. The spongy pellets showed superior performance for the reduction in the CO/Ar gas mixture compared to the dense ones, compatible with the production of sponge iron. When mixed with an amount of coal, P1200 designed for iron production in the blast furnace demonstrated an impressive reduction activity compared to P500 and previous studies. The kinetics of pellet reduction was determined by the diffusion of substances through the solid product layers having the mathematical model of 1 − 2 3 f − (1 − f )2∕3 = kt . The microstructures of pellets during the oxidative firing and reduction were also examined by X-ray diffractometry; scanning electronic microscopy; energy-dispersive X-ray spectroscopy; and Brunauer, Emmet, and Teller method.

Jun 7, 2022

By Yuting Xue, Khaled Mohamed

Rib control is a critical component of underground coal mining operations, and comprehensive rib support design is essential for ensuring the safety of miners. However, there is currently no standardized approach for rib support design in the United States. To tackle this issue, the National Institute for Occupational Safety and Health (NIOSH) has developed a standalone application, Design of Rib Support (DORS), for rib stability assessment and rib support design under development load. The rib support design in DORS starts with the rib support density, which is determined from the unsupported rib factor of safety (RibFOS). The relationship between rib support density and unsupported RibFOS was obtained from the collected field data. The objective of this research is to validate DORS rib support design by analyzing the extent to which the proposed design capability was utilized to support the coal ribs using numerical simulations. A series of numerical models with varying overburden depth and rib height were built and the ribs were supported with the DORS-recommended rib support design. The bolt load was analyzed under different conditions and the results show that bolt load varies with the overburden depth, the location of the bolt and bolt length. The load in the bolt(s) increases with the reduction in unsupported RibFOS. The bolt(s) start to yield when the unsupported RibFOS falls below a threshold value of 0.8 and secondary support is necessary.

Jun 25, 2024

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By Yuting Xue, Mark Van Dyke, Zoheir Khademian

Borehole scoping has been widely used in the U.S. underground coal mines as a method for geologic mapping and stability analysis because it is very useful for identifying rock types, voids, fractures, and formation boundaries through the direct observation of the borehole wall. An image stitching technique was proposed to generate panoramic borehole images from side-view borescopes in a previous study. However, the generation of panoramic borehole images can be affected by the borehole condition because the image stitching process highly depends on the key point detection and matching. The presence of dust and water could have a significant influence on the detection of key points. In this study, the influence of borehole conditions on panoramic borehole images was studied from the success of image stitching and the visibility of geologic features and lithology changes. Borehole videos recorded at different times, when the same borehole was freshly drilled, freshly washed with water and 12 days after washing, were processed with the proposed technique. The comparison of the stitched images shows that the presence of dust has minimal influence on the image stitching process but shows significant negative effects on the visualization of geologic feature and lithology change. In addition, the presence of water can significantly hinder the image stitching process, which in turn helps in identifying lithology change. Borehole scoping aids in identifying and mitigating hazardous conditions in underground mines, and this study provides preliminary inputs into identifying optimum borehole conditions for geologic mapping with panoramic borehole images.

Feb 1, 2025

The introduction of nitro-carbo-nitrate (NCN) blasting agents has been one of the most significant innovations in the explosive industry in the last twenty years. The most commonly used blasting agent is a rather narrowly proportioned mixture by weight of 94% ammonium nitrate (AN) and 6% No. 2 diesel fuel oil (FO) that is generally designated as ANFO. Other formulations have been developed but none of these have been as extensively used as ANFO. The relative safety of the nitro-carbo-nitrate (NCN) blasting agents almost immediately suggested bulk loading techniques to obtain economies in materials handling. The first attempt at bulk handling was to pneumatically load boreholes with ANFO. When the initial experiments were made in 1957, it was apparent that there were three problem areas which needed study to minimize potential hazards. These were: 1. Static Electricity 2. Fumes 3. Safe Handling Procedures Since those early days, considerable work has been performed in evaluating these problem areas and in arriving at procedures and recommendations that would provide the required safety. Despite the relative insensitivity of ANFO type products, all normal practices for the safe handling of explosives should be obselved. Smoking should not be tolerated in the vicinity of blasting agents and misfires should be handled in the same manner as a misfire with a dynamite charge. The purpose of this Technical Report is to discuss the problems of static electricity and fumes and the solutions that have been developed. Safe handling procedures have been discussed by the Bureau of Mines and are specified by various state and local regulations. Since regulations vary from state to state, the local, applicable regulations must be followed within the area of their jurisdiction. General information is contained in a U. S. Bureau of Mines report, IC 8179, "Safety Recommendations for Sensitized Ammonium Nitrate Blasting Agents" (1963).

Jan 1, 1973

By R. J. Sheets

"What is the primary responsibility of geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer — ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geoengineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this article will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face.What is our purpose?A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question “What is our purpose?” I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor ground water levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: Safety. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or ground water."

Jan 9, 2018

By W. Zhang

"The adsorption of collector on bornite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on bornite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. This adsorption mechanism is very similar to the one obtained with chalcocite/xanthate system. However, the result also clearly shows that the adsorption of xanthate on bornite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. The obtained AFM images also showed that the adsorption increases with increasing the collector’s concentration. When Cytec Aerofloat 238, a dialkyl dithiophosphate collector, is used, it adsorb on bornite mainly in the form of an oily substance, which can be rinsed off mineral surface by flushing with ethanol alcohol. AFM images also show that the adsorption of Cytec Aerofloat 238 increases with increasing the adsorption time. INTRODUCTION The adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) Compared to other copper minerals such as chalcopyrite and chalcocite, much less work has been done to study the adsorption collector on bornite. Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of bornite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on bornite was cuprous alkyl xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Buckley et al. (1984) investigated the surface oxidation of bornite by linear potential sweep voltammetry and X-ray Photoelectron Spectroscopy and proposed the adsorption products on bornite depended on the solution potential. Zachwieja et al. (1987) studied the electrochemical flotation of the bornite-ethylxanthate system and reported that KEX reacted with bornite through an electrochemical oxidation reaction forming cuprous xanthate between -0.4 and -0.2v (SCE). Hangone et al. (2005) studied the flotation of a bornite-rich copper sulfide ore using thio collectors and their mixtures and reported that the highest copper recoveries were obtained with the diethyl dithiophosphate (di C2-DTP)."

Jan 1, 2016

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By Xiaohong He, Qing Yu, Kaixiang Zhang, Rui Guo, Minghua Lin, Haoyu Miao

With the increasing depth of coal mining, the coal mine shaft traverses’ strata conditions become more and more complex. Shafts are often located in deep thick strata with unstable aquifers, and coal mining requires short-term rapid drainage of aquifers; the additional stress caused by aquifer water drainage is the direct cause of the shaft-lining failure. Over the years, many experts have conducted research on the shaft-lining damage caused by the consolidation and subsidence of the soil layer induced by the long-term drainage of the aquifer. On this basis, this paper conducts an in-depth study of the dynamic change of the pore water pressure of the aquifer in the short-term drainage and its influence on the response of shaft-lining strain and surface subsidence. The result shows that the Mandel effect of pore water pressure around the shaft-lining is obvious at the beginning of drainage, and the pore water pressure suddenly increases; the increase is independent of the drainage rate, which leads to the sudden increase of the shaft-lining strain value unrelated to the drainage rate. The result also shows that with the gradual dissipation of pore water pressure, the increase of shaft-lining strain is positively related to the drainage rate and negatively related to the drainage distance, and the variation trend of horizontal strain is greater than that of vertical strain, which appoints the main cause of shaft-lining damage.

Mar 16, 2023

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011

By Keith K. Griffiths

Computers are a valuable tool to the aggregate industry and should not be overlooked. The selection of proper mechanical components is necessary. Merely the addition of a computer to operate a mechanical system will not guarantee that the system will work. Material delivery by rail or truck for stock-piling and intra-plant material transfer can be accurately supervised by automation with simplified controls for the layman to use. There are mechanical problems that occur in material blending and load-out systems when such a system is automated. Such things as material flow, bridging, stockpiling methods, overloading of equipment and safety must be considered. How these problems can be overcome by proper selection of compatible mechanical and computer equipment will be discussed. Also, there are many individual material circuits in a plant that can be computerized at a nominal cost. This type of computer installation will not necessarily result in increased production, but it will produce greater efficiency in manpower. These small computers, binary counters, memory circuits and other devices and their application to the aggregate industry will also be presented. A careful evaluation of the mechanical and computer inter-relationship by someone understanding both "Rocks and Electronics" is essential to proper handling of material by computers. Computers for the mining industry may be either digital or analog computers. Unless the computer is to control some type of chemical process, such as a cement plant, the, analog computer is not required and the digital computer' will be quite adequate and less expensive.

Jan 1, 1967

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By E. R. Spencer, E. R. Bauer, G. P. Cole

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose that exceeds the U.S. Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. This paper describes the development, functions and basic operation of the initial-release version of DOSES. A revised version is being developed to incorporate additional user-suggested functions, and its development and implementation to assess noise control solutions will be described in a future article. The software relies on a time-motion study that profiles the worker’s daily activities. Observations about the worker’s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the action level or the NIOSH recommended exposure limit. The software generates a variety of interactive on-screen displays showing where, when and how the worker’s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations and times that are associated with the greatest amount of a worker’s noise exposure. DOSES simplifies and streamlines the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise overexposure of their workers.

Jan 1, 2011

By C. A. Rawlins

INTRODUCTION Radcont is a program designed by the author of this paper for the industry to use as an instrument for radiation contamination evaluation and ventilation planning system. Radiation in mines are associated with the mining of gold and gold bearing minerals, as uranium and thorium is incorporated in the mining of these minerals. Radiation contamination in South African mines is not a new concept as it was investigated by the Chamber of Mines in the early 1960's and found not to be hazardous at the time. Since some of our mines export scrap metal to customers abroad, it came to light (1991) that some of the scrap metal was radioactive. The authority that oversees the nuclear aspects in South Africa is the Council for Nuclear Safety (CNS). They investigated these matters and found that the mines needed further information regarding radioactive material and the handling of these contaminated materials. As the various mines were licensed (with various conditions incorporated) thereafter, the mines had to do their own investigations as to what extent their properties (Surface and underground) were radioactively contaminated. Some mines were found to be highly contaminated over the years of operation and controlling conditions were installed and measures installed to reduce the contamination levels. One of the conditions when issuing a licence by the Council for Nuclear Safety (CNS), is that a screening survey be carried out to determine the radiation exposure levels and corrective action to be taken if necessary. These surveys must be done by a person trained in the required procedures for such a survey. The person must also measure the risk correctly and assess the results properly. In such a survey, the internal and external exposure levels must be determined to assess the total exposure of persons working in those conditions and take appropriate action if necessary. When doing such a survey, hundreds and more likely, thou- sands of data points are recorded. In order to assess the data recorded, various integrated and difficult calculations need to be made, and takes up enormous amounts of time. (This excludes the interpretation of the results ) The following explanation of the program shows the different parts of such a survey assessment calculations to be done. The paper details the program layout and the different sub- sections within the primary program. It must be stated that the program, as with any other program, is as accurate as the data inserted into the data base. The program and details thereof are given under the following headings: 1. TOTAL EFFECTIVE DOSAGE WITH REGARDS TO: • GME required gravimetric results obtained (mg/m3) • Thick layer or total contamination measured (Bq/m2) • Dry condition surveys with dust loads taken as a Standard l0mg/m3 • Wet conditions survey with dust loads taken as l mg/m3 • Airborne long lived alpha and beta activities as determined by analysis in Bg/m3 • LTD (Thermoluminescent Dosimeter). Results as obtained from the SABS (South African Buro of Standards) are recorded in this section for each month of the year for each individual worker. An average dose is then determined at the end of the year. • Bucket measurements as recorded. • Smear samples (Loose contamination). As determined by Electra or by analysis • Occupational factors for Metallurgical and Engineering occupations in and around the Metallurgical facilities of your mine. • All underground dosage determination and calculations. (Radon and Thoron) 2. INFORMATION REQUIRED WHEN PROGRAM IS INITIALISED: As the program is started, it opens up on the contents page. Here there are various options to choose from, but one is cautioned as a beginner in operating the program, not to perform any tasks before carefully reading these instructions. Firstly, one must go to the 'Information required" pushbutton. Press this button. The information required page is shown where the cursor can be moved to the block where one can enter the specific mines name. To enter a mines name, put the cursor in the block provided and just insert the mines name with the normal keyboard keys and press the enter button on the computer keyboard. To enter the other information required such as Alpha and Beta instrument efficiency, ALI (Annual limit of intake) and probe area, one can either press the 'Data required" button for a dialog box information or enter it manually by just putting the cursor in the block provided and entering as did above. In order to insert all the required information for the pro- gram to calculate the information required, one must proceed further by entering the area names surveyed in the spaces provided. There are 20 spaces to enter 20 different areas surveyed. One must further also provide the amount of days worked in each area (i.8. 250) in the block provided. The de- fault is 250 days. There are also standard information given in the information data page such as breathing rate (1,2 m31h), 8 hours worked per day, 5 days per week and 50 weeks per

Jan 1, 1997

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By R. J. Sheets

"INTRODUCTION What is the primary responsibility for geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer – ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geo-engineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this paper will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face. WHAT IS OUR PURPOSE? A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question above. I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor groundwater levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: SAFETY. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or groundwater. The objective of a hydrogeologist is to ensure the soil or rock around an open pit or underground mine is dewatered; this specific objective will reduce pore pressures which could lead to a possible ground failure. They ensure a working bench/UG level is dry, so operations are not dealing with adverse conditions while mining. A geotechnical engineer is expected to use all available information and engineering judgement to provide design recommendations, so that the mine will not catastrophically fail. Additionally, they will implement the monitoring systems to identify hazards in advance in the event that the design is flawed and people need to be evacuated. We all know that safety is important to everyone; however, our particular set of technical skills play a significant role in ensuring the safety of a large portion of the global mining workforce."

Jan 1, 2018

By Raja V. Ramani

Discussion in this section of the Handbook is limited to the working environment of miners, the mine workers themselves, and the machines used in mining (Fig. 11.0.1). The contents emphasize personnel health and safety aspects and engineering design and control practices to ensure a productive health and safety environment. Reference is to the health and safety of the individual miners as well as to the safety of the working environment. This Handbook also contains references to health and safety regulations in Chapter 3.2 and environmental protection in Chapters 3.4 and 7.3.

Jan 1, 2008

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019