Search Documents

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

This paper combines theoretical and experimental analysis to conduct relevant research to improve the accuracy of predicting paste yield stress by slump flow. The analytical model of slump flow for yield stress is derived based on a mini-cylindrical mold with a height-to-diameter ratio of 1. It shows that the dimensionless slump flow is a monotonic decreasing function of the dimensionless yield stress and is independent of the material type (specific gravity), which provides a theoretical basis for quantifying the rheological properties of paste with slump flow. Three different tailing-prepared pastes were tested for their slump flow and implemented rheological tests simultaneously. The yield stress is obtained based on the Bingham model fit, as the measured value of the yield stress is substituted into the derived theoretical model. The studied pastes yield stresses range from 34.78 to 524.08 Pa, with corresponding dimensionless slump flow of 3.43 to 1.09. The results showed that the calculated slump flows were generally greater than the measured values. The analysis showed that this was mainly due to the thixotropy of the paste, with minor deviations ranging from − 1.5 to 5.8% for the less thixotropic pasted prepared from tailing C. An approximate analytical solution for yield stress as a function of slump flow is obtained using Taylor’s formula. However, it is unsuitable for predicting the yield stress because the yield stress calculated by this function is much higher than the measured value. The empirical yield stress model was constructed and experimentally verified. The results show that the empirical formula has high accuracy and good generality. The deviation of the studied pastes is between − 15 and 5%, which provides a practical method for rapid and accurate prediction of paste yield stress in mine sites.

Jun 1, 2023

By Zong‑yu Li, Shao‑jian Ma, Xiao‑jing Yang, Jin‑lin Yang, Xing‑nan Huo, Heng‑jun Li

Optimizing and adjusting the particle size composition of grinding products is of great significance for improving economic benefits and resource recovery and utilization. In this study, grinding contribution and quantitative separation of impact and grinding mechanism in cylindrical mill were creatively researched, and the grinding technical efficiency of impact and grinding was coupled to the grinding technical efficiency of grinding in drop-off mode. The results showed that the contribution rate of impact and grinding in grinding in drop-off mode varied with the grinding time. On the whole, the contribution rate of impact action increases with the grinding time and gradually becomes stable, and the contribution rate of grinding effect was just the opposite. Under the experimental conditions, the main contribution of the grinding process is impact action, and the contribution of grinding action is auxiliary. In addition, the contribution rate of impact and grinding effect in grinding in drop-off mode was also related to the feed particle size. The contribution rate of impact effect decreased with the decrease of feed particle size, while the contribution rate of grinding increased inversely.

Aug 3, 2023

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By F. Habashi

The Republic of South Africa is a heterogeneous mixture of Black Africans, Afrikaans, British, Indians, Malayans, French Huguenots, and many others from Europe and Asia. A decisive date in its recent history is the collapse of the Apartheid Regime in 1994. For a metallurgist, South Africa is the country of diamonds, gold, platinum, and many other metals. In 1887 Cecil Rhodes (1853-1902) was able to take control of the De Beers Mining Company after the discovery of diamonds at Kimberly in 1866. It was there where the so-called School of Mines was inaugurated in 1896.

Jan 1, 2010

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

This study presents a method for recovering valuable metals and synthesizing anhydrite from steel slag using sulfuric acid leaching and solvent extraction. The process achieved high leaching efficiencies for V, Ti, Fe, and Mg, and produced anhydrite with 93.09% purity. The leachate was further processed to separate and recover V, Ti, Fe, and Mg using selective stripping and precipitation methods, offering a sustainable approach to steel slag utilization.

Jan 22, 2022

By A. S. Speirs

Over the last few years, the never-ending search for mineral wealth has taken the exploration efforts of Canadian mining companies further and further into the High Arctic and isolated locations where regularly scheduled transportation and communication facilities are nonexistent. Names such as Black Angel, Nanisivik, Asbestos Hill, New Quebec Raglan, Rabbit Lake, and Arvik are today frequently mentioned in mining publications. Twenty years ago, mining in these locations was unheard of, mainly due to logistic problems. However, improvements in the design and use of helicopters, STOL aircraft, and icebreakers in northern areas have helped to overcome these problems, making these locations more attractive to mining companies. Since 1969, when Redpath completed its first Arctic project at Texas Gulf's Scrathcona Sound property on the northern tip of Baffin Island, Redpath has been actively involved in contracting and engineering projects in three general areas: the High Arctic, Ungava and Greenland. A map showing some of these projects is shown in Figure 1. In these areas, permafrost conditions exist from a depth of 274 metres in Ungava to a depth of approximately 610 metres in the Little Cornwallis Island area, with rock temperatures ranging from -5°C to -13°C. Outside temperatures range from a low of -50°C in the winter to a high of 21°C in the summer. High winds in the winter result in wind chill factors lower than -73°C

Jan 1, 1980

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By Vhutali Carol Madanda, FHATUWANI SENGANI, François Mulenga

The first introduction of fuzzy theory in the nineteenth century created room for continuous research and application in various fields. Fuzzy set theory has been globally applied in geotechnical engineering, and research in this field continues to date. The fuzzy inference system is considered to be one of the most popular techniques adopted to resolve some of the geomechanical challenges faced in both surface and underground excavations. This paper unpacks fuzzy theory-based approaches in mine geomechanics with the aim of expanding the innovative application of the same approach specifically in tunnel geomechanics. This aim was achieved by conducting a review of recent successful and unsuccessful applications of fuzzy inference systems in underground excavations/tunnelling geomechanics. Indeed, this review has outlined some cardinal points associated with the ability of the technique to solve complex geomechanics problems. However, the success of the technique was accompanied by a few limitations associated with the methodology. Finally, a future outlook associated with the technique has been established.

May 15, 2023

By B. A. Filas, H. N. Lammers

Responsible environmental, social, and governance (ESG) practices are not new to mining. It is the ESG acronym that has become the “flavor-of-the-day” with the stock markets, accounting firms, and investment strategists. This increased interest from the financial sector has heightened executive awareness and accountability to where corporate leadership and directors are proactively prioritizing ESG issues from the top down within their companies. This paper aims to convey what the authors believe one needs to know to be able to conduct and prepare effective ESG audits and reports. The emphasis is on how ESG fits within the mining sector, some of the ways that many mining companies have been practicing ESG responsibility for decades, the importance of effective communications with stakeholders, and the roles that regulatory and international lending institutions play in enhancing ESG practice on a global scale as a precursor to the discussion on ESG auditing and reporting. Without this background, the ESG audit may become a purely academic exercise.

Feb 1, 2023

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By J. Appleby

This paper reviews earlier in-plant testing at the Sidbec-Normines pelletizing plant at Port Cartier, Quebec, Canada. It describes the result of the more prolonged use of coke breeze during recent months and in addition, the effects of varying dolomite and coke additives upon the metallurgical properties of the pellet production have been studied. Mention is also made of some brief test work carried out to use peat moss as a carbonaceous additive to the pelletizing process and in particular the plans for future work in this respect. Earlier laboratory pot-grate test work had indicated that a production rate increase of between fifteen and twenty percent was a practical possibility, or alternatively that the plant could be run at design rating with significantly lower energy consumption. These energy reductions were of the order of ten to fifteen percent for fuel and main process fan power respectively. The physical and metallurgical pellet properties for both blast furnace and direct reduction furnace use were little affected by the production rate increases, and were actually somewhat improved when practicing maximum energy conservations. Pellet properties could be further improved by not extracting the maximum energy economy. Two phases of carefully controlled in-plant testing were run to assess the effect of energy conservation under plant conditions. These two phases of testing confirmed that an overall fuel saving of approximately fifteen percent could be realized, with a reduction in the Bunker C oil consumption of about forty-five percent, and a reduction in main process fan power of approximately ten to fifteen percent. The present scope of work is aimed at establishing the use of varying levels of coke addition up to about one percent under normal plant operating conditions.

Jan 1, 1980

By José Luis Lee Moreno

This paper presents a preliminary phase of a study being conducted by the Department of Geochemistry of the Consejo de Recursos Naturales No Renovables in the vicinity of the Pachuca-Real del Monte Mining District. This district is located in central Mexico, about 100 km northeast of Mexico City. It has been in operation for the past 450 years and has produced about 38 million kg of silver and about 190 thousand kg of gold. At the present it is being worked by the state owned mining company of Real del Monte and Pachuca. The rocks of the area consist mainly of Tertiary volcanics, ranging in age from early Oligocene to late Pliocene. Ore bodies are recognized as epithermal, vein type fracture fillings. The main ore minerals are argentite and acanthite normally accompanied by base metal sulphides, Gold is present in small amounts as native gold and in other minerals. Orientation geochemical studies performed on soil and rocks over known veins in the district, showed zinc to be the best indicator. Lead and silver anomalies are restricted to the immediate vicinity of the veins, mercury shows the mineralized structures only when the "C" horizon is sampled, while antimony gave erratic values. The El Chico area is about 10 km north of the Pachuca-Real del Monte district and covers approximately 400 sq km. Geological evidence indicated the possibility of an extension of the Pachuca ore bodies in this area. Results obtained from soil and rock samples from El Chico, showed several anomalous area. Detailed investigations proved these anomalies to be related to faults and fractures which in several cases have been found to be mineralized. Drilling is planned with preliminary results expected by late 1974.

Jan 1, 1974

By N. B. Prenn

Many recent projects have been developed and mined based upon imaginary reserves. Imaginary or "geo-fantasy" reserves have cost many companies millions of dollars. The significant and varied technological advances in the mining arena have done little to curb reserve calculation problems. These advances may have served to increase the prevalence of reserve problems by putting more tools in the hands of personnel not properly trained or experienced in reserve estimation. This paper will discuss potential problems related to calculating reserves, which include: SAMPLING ERRORS -obtaining a representative sample. -Decay analysis of wet RC drilling -Bias introduced by sample preparation. -Assay bias; Coarse gold. -Specific gravity samples. GEOLOGICAL ERRORS -structural boundary definition. -Separation of high grade and low grade zones. -Incorrect continuity assumptions MODELING ERRORS -Too much influence of high grade samples. -Improper method of calculation. -Assumed range of influence. -Errors in the data. ENGINEERING ERRORS -Inaccurate assumptions. -Inadequate metallurgical testing. -Designed bottlenecks.

Jan 1, 1992

Ferric (Fe3+) ions are omnipresent in flotation circuits. Depending on pH and the nature of the ore body, Fe3+ ions may play a role in the adsorption of thiol collectors on sulfide minerals. To investigate this possibility, a two-compartment galvanic coupling cell was designed. This cell was used to monitor changes in contact angle of a sulfide mineral in one compartment, while varying concentrations of the Fe3+ ions in the other. The results showed that Fe3+ ions promote xanthate adsorption as indicated by the increase in contact angle. Implications of this finding in sulfide mineral flotation in general will be discussed.

Jan 1, 1998

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999