Search Documents

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By Raymond W. Peterson

The practice of Countertrade and all of its variations has increased dramatically during the last five years in great part due to the worsening world economic situation and the Third World's increasing debt problems. Conventional wisdom has held that the goods finding their way into countertrade will tend to be manufactured goods of ever increasing value added. It is my contention that this has not been the case. The continued depression of most metals and minerals prices has conspired to keep a great number of metals and raw materials in the forefront of countertrade negotiations. The concept that if a country needs hard currency it will simply sell metals into world markets for cash has been significantly modified by countertrade which encourages subsidies for raw materials which are in turn funded by higher prices for the manufactured goods which the country must import. Countertrade is a term that is relatively new to most of us who have been involved in the international trade of metals and minerals, but it is one that we will continue to hear more of in the future. Countertrade as it is generally known today had its beginnings after the Second World War in Eastern Europe. As the shattered economies of Europe struggled to right themselves, a "cashless" system of trade developed. This system included such ancient concepts as barter as well as more modern ones like bilateral clearing agreements. For over 30 years countertrade was confined mainly to the COMECON nations and their various trade protocols with Third World nations. If metals and minerals were involved, there was little disruption of world markets by such examples as Cuba shipping ferronickel and sugar cane to the U.S.S.R. for a host of manufactured goods and oil. As the world's economy began to slow in the late 70's and the debt crisis began in earnest in the early 801s, this all began to change. As more and more nations which had previously been almost totally dependent upon their mineral wealth over-extended themselves in an attempt to industralize, they concurrently found their income from minerals falling, due to the decreased demand and subsequently lower prices available in the marketplace. At first these nations attempted to balance their payments by promoting the sales of their high value-added manufactured goods. We have all heard numerous examples of U.S. companies going to sell their high technology products in Rumania or Yugoslavia and being confronted with counterpurchase requirements for machine tools, shoes or drill bits. When faced with these demands, a number of companies chose not to sell into those markets while others merrily signed up the obligations without much intent to carry them out. The Performance Bonds required were generally minimal, especially when considered in light of the high margin inherent in high tech items; and the penalty clauses were equally small or nonexistent. A third group of companies actually tried to buy the machine tools or drill bits either for their own internal use or resale but found that due to poor quality and high prices, they were faced with a difficult if not impossible task. This is not to say that no one was able to fulfill a countertrade requirement, but the success ratio on these transactions was incredibly low. This was one of the major contributing factors to the reputation that countertrade has gained as a discipline ... "that it is mostly talk and very little action." As this situation slowly evolved, both the countries imposing the countertrade obligation and the exporters assuming the obligation began to realize that something

Jan 1, 1986

By G. E. McClelland

Introduction Many discoveries have been made during the-past decade of low grade gold-silver deposits in the western US. This has stimulated development of low cost cyanidation procedures for precious metal extraction. Heap leach cyanidation techniques possess considerable potential for application to these low grade ores, small ore bodies, mine strip waste, and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successful, these resources must have good permeability to achieve uniform distribution of the cyanide solution throughout the heaps. Some of the most difficult of the gold and silver ores to treat successfully by heap leaching are those containing excessive amounts of clays, or fines generated by crushing. Presence of excessive amounts of slimes, -50 µm (-270 mesh), in the heap leach feed will slow percolation, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap. This causes the leach solution to run off the sides of the heap rather than penetrate the ore bed. The problem of heap leaching ores with fines can be aggravated while preparing ore heaps because of the natural sorting of coarse and fine material that occurs. This phenomenon results in concentration or ore fines in the center of individual ore piles and concentration of larger rock fragments of the lower slopes and base of the pile. When the individual piles within the heap are leveled off for the installation of the sprinkling system, additional segregation occurs as the fines sift through the coarser ore particles. This results in localized areas or zones with marked differences in permeability. Consequently, the leach solutions follow the course of least resistance. They percolate down through the coarse ore regions and bypass or barely wet areas that contain large amounts of fines or slimes. Effective use of marginal gold and silver resources by heap leaching required development of new methods to achieve more uniform size distribution when preparing ore heaps and better slime control during leaching. Early methods Agglomeration and balling of crushed ore to produce a porous and more uniform feed material for heap leaching is a viable method for treating clayey ores. Researchers from the US Bureau of Mines in Reno, NV began agglomeration pretreatment research in the mid-1970s for applications to and exploitation of these poor percolating feed materials. Little attention had been given to such methods before the Bureau's research. In 1905, T. C. Scrutton developed a unique technique for obtaining rapid vat leaching of a clayey ore where the gold was finely disseminated. His technique consisted of rolling the ore down a chute inclined at 60° to form agglomerates or balls readily permeable by the cyanide solution. However, these agglomerates lacked rigidity. And, to ensure good percolation leaching and washing, they could not be bedded in layers more than 1 m (3 ft) deep. If this depth was exceeded, it is difficult to obtain uniform leaching and washing. This results in reduced gold recovery. Shepard and others in 1937 studied the addition of lime and carbon dioxide or calcium carbonate to gold-bearing tailings to form agglomerates suitable for vat leaching. Satisfactory percolation flow rates were achieved in 90 g (3 oz) scale experiments, but the reagent requirements were cost prohibitive. Agglomeration and pelletizing has been used in other segments of the mineral industry. This technique was first used successfully around 1911 for pelletizing iron ores. Since then, agglomeration

Jan 7, 1986

By B Scheiner, D. A. Stanley

Introduction Treatment of ores to recover metal and mineral values results in waste materials usually in the form of dilute slurries. The US Bureau of Mines (USBM) investigated a technique for dewatering phosphatic clay waste by flocculating with polyethylene oxide (PEO) and dewatering the resulting floes on a static screen and/or trommel screen (Schemer et al., 1985). In the investigation, it was determined that PEO was far superior to polyacrylamide polymers for this type of dewatering. This paper discusses reasons for this superior performance. Comparison of PEO with polyacrylamides Dewatering experiments were conducted by adding PEO solution from a burette to a stirred clay slurry. The dewatering endpoint was characterized by rotation of the floc mass as a unit, a clear supernate, a maximum floc size, and a minimum floc volume. Additional water was removed from the floes by hand squeezing (Schemer et al., 1985). The clays investigated were sodium, potassium, magnesium, calcium, and aluminum exchanged montmorillonite and attapulgite. Nine commercially available (Superfloc) polyacrylamides were compared with PEO at two polymer concentrations. Results are summarized in Table 1. The solids content of the dewatered clays ranged between 24% and 33% and was highest for PEO-treated material. These results and the data in Table 1 indicate that PEO is superior to polyacrylamide in terms of polymer dosage required. Superflocs 16 through 128, like PEO, are nonionic and should give similar results to those for PEO if the flocculation mechanism is the same for both type polymers. Superflocs 204 through 214 are anionic with increasing anionic character from 204 to 214. Generally, the anionic polymers gave the best results for the polyacrylamides tested, but in terms of dosage they were not as good as PEO. Correlation between flocculation and dewaterability of waste slurries The overall mechanism for mechanically induced clay dewatering is not completely known, but certain observations can be made. For instance, when a polymer is adsorbed on a clay such as montmorillonite, the polymer desorbs interlayer water. Polymer adsorption is driven by favorable entropy changes associated with this water desorption. It is also known that the -CH2-CH2- links of the PEO chain are sufficiently hydrophobic to lead to physical adsorption of the polymer (Theng, 1979). For montmorillonite slurries, the sheet-like fundamental particles, called tactoids, consist of a small, variable number of aluminosilicate layers together with interlayer water and exchange ions. The flocculation process consists of adsorption of polymer on the tactoid. Loops and tails of polymer that extend into solution then adsorb on another tactoid, forming a bridge. Mechanical action, induced by hand squeezing or in a trammel, joins the bridged tactoids face-to-face and edge-to-edge to form regions of high density. Similar orientation effects are observed for the needle-like attapulgite crystals (Schemer et al., 1985). Proposed flocculation model Generally, statements concerning flocculation and dewaterability apply to both PEO and the polyacrylamides. However, PEO has additional interaction with the clay material when compared with polyacrylamides. PEO is a polymer with repeating -CH2-CH2-O- groups and interacts with montmorillonite through a water bridge whose strength is greatly influenced by the exchange ion. To obtain insight into this interaction, a series of experiments were conducted in which different ion exchange forms of montmorillonite and attapulgite clays

Jan 1, 1987

Introduction One hundred years ago, a recent college graduate created the US aluminum industry. He found an economic way to crack the primeval bond that makes the metal so special. Aluminum doesn't "rust" - oxidize progressively. Rather, when exposed to air, it instantly forms a gem-hard but microscopic oxide coating. This seals off oxygen from the metal underneath. Scratch it and the seal reforms instantly. That tight chemical bond is the reason the metal is not found in nature; it exists only as a compound. The bond had to be broken to free the shiny metal. But once it is free, that self-sealing protection, alongside a remarkable strength-to-weight ratio, offers a marvelous material. Until 100 years ago, finding a way to do that economically was a challenge that defied science. Then it was solved, in a remarkable coincidence, on both sides of the Atlantic. And the way was paved for a material that would become the second most widely used metal in the world. Until that time, aluminum was a rare and precious metal. But then two young scientists independently invented the process that took aluminum outside the laboratory and into applications ranging from pots and pans to spacecraft. Discovery of aluminum Other major metals - copper, iron, lead, gold, and silver - had been used for thousands of years. But aluminum was entirely unknown until 1782, when French chemist Antoine Lavoisier suspected its presence. It was not actually discovered until Sir Humphry Davy, in England, detected it in clay in 1807. It was first isolated as a free metal only in 1825, by Denmark's Hans Christian Oersted. For years, laboratory methods yielded aluminum only in tiny amounts costing about $1200/kg ($545 per lb) - $13,333/kg ($6000 per lb) in today's dollars. Methods developed by French scientist Henri Sainte-Claire Deville in 1854 cut the cost to about $200/kg ($90 per lb). King Frederick VII of Denmark had a helmet of aluminum and gold. And Emperor Napoleon III of France reportedly served his most exalted guests at a state dinner with aluminum plates. He left the lower ranks to dine from pure gold. Deville and others continued to reduce production costs. But the price of aluminum still rivaled silver - $31/kg ($14 per lb) versus about $35/kg ($16 per lb) for silver. Then in 1884, a 2.8-kg (6.25-1b), 230-mm-tall (9-in.-tall) aluminum pyramid was cast as the tip of the Washington Monument. It was probably the first architectural use of aluminum. And it is still there after more than a century. The attractive properties of aluminum were obvious: it is lightweight but strong, conducts heat and electricity, reflects light and other electromagnetic radiation, and resists corrosion. But its commercial promise was blocked by its cost. In 1885, the price of aluminum was $17.70/kg ($8 per lb). It stayed there for the next couple of years until the Hall-Heroult process brought it down sharply. Hall-Heroult process lowers aluminum costs The characteristic that kept aluminum hidden so long continued to thwart chemists. Aluminum clings to oxygen so tightly that it is never found as a free metal in nature, and it is hard to break that bond chemically. The best chemical methods of the 1880s required sodium, and sodium itself was expensive. At Oberlin College in Ohio, chemistry professor Frank Fanning Jewett advised his students that anyone who could make aluminum inexpensive would do humanity a favor and get rich as well.

Jan 3, 1987

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By K. A. Smith, X. Cheng

Introduction The separation of minerals from complex sulfide ores by flotation requires careful control of the surface chemical behaviors of the minerals constituting the ores. When the minerals in the ore are finely disseminated, extremely fine grinding is needed to liberate the minerals. Fine grinding is not only an energy-intensive operation, but also influences the flotation behaviors of liberated minerals. Steel balls are commonly used for grinding. Galvanic interactions occur not only between sulfide minerals and grinding media but also among the different sulfide minerals themselves. The electrochemical characteristics of chalcopyrite and pyrrhotite when they are independently coupled with steel grinding media and the relevance of these characteristics to the flotation behavior of these minerals have been exten¬sively studied (Cheng and Iwasaki, 1992: Li and Iwasaki, 1992). These studies dealt with reactions in two electrode combinations, simulating mineral-grinding medium and mineral-mineral interactions. In practice, however, it is more common to involve more than one sulfide mineral. In a study of a pyrite-pyrrhotite-mild steel system, Pozzo et al. (1989) provided evidence that a mineral having an intermediate potential could behave differently, depending on the condi¬tion of galvanic contact. This investigation was undertaken to study a chalcopyrite-pyrrhotite-mild steel system to gain better in¬sight into the mechanism of multiple galvanic interactions. A three-electrode system was chosen to simulate a typical copper sulfide ore. The sulfide minerals were represented by chalcopyrite and pyrrhotite. The grinding medium was rep¬resented by mild steel. The nature of galvanic interactions involving these minerals and grinding medium in an oxygen atmosphere was investigated in a three-electrode combina¬tion, and an attempt was made to relate the laboratory flotation results of pyrrhotite-chalcopyrite ores. Possible implications to the differential flotation of complex sulfide ores are discussed. Key words: Electrochemistry, Flotation, Sulfide ores Experimental The pyrrhotite (57.74% Fe, 0.09% Cu, 4.84% Ni and 36.54% S) sample was obtained from Falconbridge Ltd.'s Strathcona mine, Ontario, Canada, and the chalcopyrite (26.00% Cu, 28.57% Fe, 0.05% Ni and 31.52% S) sample came from Transvaal, South Africa. Mild steel (AISI 1020, 0.2% C) was chosen to represent grinding media. A conventional three-electrode cell was used in the elec¬trochemical measurements. The working, counter and refer¬ence electrodes were, respectively, sulfide minerals or mild steel, graphite rod and saturated calomel electrode (SCE, 0.245 V vs. standard hydrogen electrode). The exposed areas of the sulfide minerals and grinding medium electrodes were approximately the same (0.17 to 0.19 cm2). The preparation methods of working electrodes, the reagents used, the experi¬mental procedures and the instrumentation were the same as those described previously (Cheng and Iwasaki, 1992). Rest potentials of pyrrhotite, chalcopyrite and mild steel were measured individually in 0.05-M sodium sulfate solu¬tions. Combination potentials and galvanic currents of the sulfide minerals and grinding medium were measured in short-circuited two- and three-electrode systems. All poten¬tials in this study are quoted in volts with respect to the standard hydrogen electrode (SHE). To simulate the constantly abrading conditions in a ball mill, rest potentials, combination potentials and galvanic currents were also measured by rotating a porcelain ball against chalcopyrite, pyrrhotite and mild steel electrodes in

Jan 1, 2000

By J. G. Clevenger

Introduction Computer-based haul truck dispatching has been operational at Tyrone since May, 1980. The system, known as Dispatch, has accomplished significant productivity gains compared with the former method of manual radio dispatching. These gains translate into a reduction in equipment requirements or an increase in production. An operational mine may choose to increase production or reduce the number of equipment shifts operated, resulting in substantial operating savings. Dispatch Description The core of Dispatch is a VAX 11/780 computer. Originally purchased with 512 kbytes of memory, the system is now upgraded to 3.75 Mbytes to accommodate users from all areas of the operation. Dispatch alone requires 200 kbytes of locked-in memory, with an additional 300 kbytes of memory available on a top priority basis. The computer, located in the Tyrone Branch general office building, is connected by under-ground cables to the dispatch tower, 3.2 km (2 miles) from the general office. Four two-paired lines are used to drive two cathode ray tubes, a printer, and the Dispatch master panel. One CRT continuously displays pertinent pit information for the dispatcher's use. Routinely displayed transactions include truck assignments, changes in shovel material type, truck and shovel breakdowns and delays, and changes in truck, shovel, or dump status. Er¬ror detection capabilities include late arrival and improper input from the field panels. The second display terminal is used for utility reporting and input functions. Status reports are displayed for availability, position, and material type being handled by any given truck or shovel. Fuel reports are available indicating the time last fueled, quantity of fuel delivered, and the time spent fueling. A truck factor utility reports relative performance to other trucks and a shovel utility reports efficiencies in tons per shovel shift. Instantaneous shift reports and mine status reports are available. Inputs such as lineups, operator changes, new travel times, shovel bias, tie down times, and lunch times are all handled with the utility display terminal. The printer records a hard copy of operating truck locations and production from the beginning of each shift. If there is a system malfunction, the printer copy is readily available to the foreman for radio dispatching. The Dispatch master panel is a microprocessor-based panel that allows the dispatcher to override any computer-assigned transaction. Classification of "bad order" conditions and acceptance of certain field messages is entered through the master panel. This panel communicates with all truck and shovel field panels via UH radio frequency through a repeater tower located on a high ridge contiguous to the mining area. Each truck and shovel field panel unit transmits a coded signal that is identified by the computer. A typical communication sequence between field panels and the computer for one complete truck cycle is: • The truck panel LED display indicates the shovel number to which it is assigned. The truck arrives at its assigned shovel and the operator presses the "Arrive" button on the truck panel. As the computer receives the "Arrive" message, it concludes the return (empty) travel time and begins accumulating idle time before loading. • When the first dipper of muck is placed into the bed of the truck, the operator presses the "Load" button. The computer concludes the truck idle time accumulation and begins the loading time calculation. • When the truck is loaded, the shovel operator presses the "OK"

Jan 9, 1983

By D. A. Norrgran, J. A. Wernham

Introduction In view of the continuing depletion of natural resources, requirements for energy conservation, plant optimization and hazardous waste management, and environmental consciousness, recycling and secondary recovery of materials are being developed with increasing interest Many secondary recovery processes are being developed that apply mineral processing technology. Gravity separation, magnetic separation and flotation have all emerged as explicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. The concept of the alternating magnetic field eddy-current separator was developed over a century ago using rudimentary electromagnets (Patent 400317 issued to Thomas Edison on March 26, 1889). Widespread acceptance was, however, hindered by high costs, marginal results and poor economic incentives for secondary recovery. With the recent increased interest in secondary recovery and the development of high-energy rare earth permanent magnets, the eddy-current separator has now gained prominent acceptance. The separation forces imparted by an eddy current separator are the function of the magnetic field intensity and the alternating frequency of the magnetic field. The evolution of permanent magnets has provided a cost effective alternative for the generation of high-intensity magnetic fields. High-energy rare earth permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymium-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits. The eddy-current separator has been successfully applied in several metal sorting and recovery operations. Most common is the sorting of metal from shredded automobile scrap and municipal waste. With the advent of high-frequency, high-intensity magnetic fields, the separator has advanced to the point where it has direct application in the beneficiation of fine sized metals. Relatively fine sized (-1/4 in.) metal bearing slags and spent foundry casting sands as well as precious metal hearing electronic scrap demonstrate excellent metallurgical response to the eddy-current separator, and applications have progressed to finer materials and more selective separations. Theory Electrical currents are induced in all conductors when exposed to an alternating magnetic field. The induced current generates a magnetic field in the conductor that opposes that of the alternating magnetic field. Figure 2, is a schematic illustration of generated eddy currents. In this particular example, the alternating magnetic field is produced by a series of permanent magnets mounted on the circumference of a rotor. The permanent magnets have alternating polarity. As the rotor revolves, an alternating magnetic field is produced, and the rate of revolution determines the frequency of the alternating magnetic field. When a conductor, such as a metallic disc in the illustration, is placed in the alternating magnetic field, a closed loop current flow occurs. The current loop in the conductor produces a magnetic field that is a mirror image of the alternating magnetic field. At any point in time, the induced magnetic field in the conductor directly opposes the alternating magnetic field. This opposition of magnetic fields produces an instantaneous repulsion in the conductor. The conductor is consequently repelled from the rotor. The alternating magnetic field has no effect on nonmetallic materials as they pass through the magnetic field and discharge the rotor in a natural trajectory. [ ]

Jan 1, 1992

By David J. Starbuck

For small precious metals mining to show a comeback a different perspective must be taken than that of larger mining companies. This perspective must be much the same as that of past successful smaller mining enterprises such as when the US had a need for Uranium. Abandoned mines and environmental concerns in older mining districts have discouraged many from entering with the attitudes of why try there if so many unsuccessful mines exist. A small mining venture can be successful there but must have a "think smart'' attitude. There must be a thorough understanding of deposits, utilization of advanced technology and a properly managed mining operation. "THINK SMART" MINING The small mine operator is usually looking for small high grade deposits, consequently, long term success depends on a series of small successful mining operations. The small miner must succeed right-off or credibility and future project funding will suffer. No veteran of even a few years in the mining industry needs to be told that a dollar spent on production today fails to yield as much as it once did. More efficient equipment and techniques have helped soften the problem, but there is little likelihood that a mining company can do much to control inflation, wages, regulations, or grade. That leaves the small miner to "think smart" as one area where operating dollars can still be stretched to produce more than they presently do (Gardner. 1981). In the planning stage of a mining venture, when most options are still open, the main controllable elements are market timing, deposit selection, cutoff grade, mining method, mine design, mining sequence, rate of production build up, process design, project financing structure, project management, and project ownership structure. During planning, optimum criteria can be established for each of these. Once a mine is in production, these options are foreclosed or at least severely constrained. The more thought given to a mining program using all information available the less the risk of encountering disabling surprises. Thus the intent of this paper is to suggest the "think smart" attitude most small mine operations use for long term success. If one looks at a number of successful mining ventures, whether large or small, there is a general logic most have followed to be successful. They have used proven exploration, mining and processing techniques along with economic evaluation and experienced personnel to improve their odds. LOGIC IN DEVELOPING A FEASIBLE VENTURE Most successful small mine ventures achieve positive cash flow as quickly as possible by seeking out those deposits which require the least time and expense on activities leading up to production. To do this they look for deposits that are the most accessible, easily investigated, mined and processed with the cheapest fundamental methods. The general sequence of events starting with district selection are deposit selection, preliminary feasibility, exploration, detailed economic feasibility, mine planning, development and production. Each successive step becomes more costly requiring intermediate decisions along the way. District Selection Small operations should look for known deposits which favor the occurrence of the type deposit sought rather than efforts in unproductive areas. Known deposits in developed areas have some advantages over remote areas: 1. More alternative methods of transportation are available. 2. A larger stable work force is available. 3. The area is usually more pro-mining. 4. Power, water, housing, technical services, skilled services, schools, recreation and shopping are available.

Jan 1, 1987

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By R. Kneisley, D. Conover, K. Haramy, K. Hanna

INTRODUCTION Coal mine entry intersections are high-risk areas for roof falls due to inherently wide roof spans, excessive stress, and variable intersection shapes resulting from breakthrough misalignments. Statistics from underground coal mines reveal that a high percentage of injuries occurs from roof and rib falls in entry intersections (Peng, 1980). The U.S. Department of the Interior, Bureau of Mines, is conducting a field research project to investigate failure modes surrounding underground coal mine entry intersections. The research objectives are to (1) develop a method to determine failure modes and stress-displacement relations around coal mine intersections and (2) develop engineering guidelines and empirical relationships for use in designing safer coal mine entry intersections. The basic approach to achieve the objectives is to instrument and monitor intersections before, during, and after intersection development in order to determine contributing parameters, such as in situ stresses, stress changes, strata movement, geology, physical properties, and mining sequence, that may influence the short- and long-term stability of the intersection and adjacent entries. This paper describes a rock mechanics instrumentation program, data analyses, and a comparison of two case studies conducted at two underground mines, designated as "A" and "B", in the Illinois Coal Basin. The instrumentation plans and data collected during development and long-term monitoring of four-way intersections and adjoining entries are presented. Data analyses of pre- and post-mining roof stress, pillar loading, strata movement, roof bolt loading, and geologic features are included. INTERSECTION FAILURE MECHANISM The region surrounding an entry intersection is characterized by different failure criteria than the region surrounding a single entry. Stresses induced during intersection development may result in a high incidence of roof and rib failures. Various numerical modeling techniques have been used to evaluate the failure modes surrounding intersections (Gercek, 1982; Chugh et al., 1975). Numerical modeling techniques include problems associated with the analysis of post-failure behavior, provision for different horizontal stresses (i.e., 01 f 021, and determination of inputs required for any non-elastic behavior. It seems likely that more sophisticated failure criteria, based on actual field data, are needed. The Bureau of Mines has conducted an extensive instrumentation program to investigate actual intersection failure mechanisms and to provide an improved understanding of stresses and deflections using beam and plate theories. Beam theory is not applicable to analyzing intersections (Wright et al., 1964); however, it can be used to explain roof deflection and failure (shear and flexure) of adjacent entries and to provide an improved understanding of stress changes and displacements as the entries, crosscuts, and intersection are developed (Hanna et al., 1985). Beam theory may be used for entries when the roof length is twice the width. When the length is less than twice the width (as in intersections), the roof must be analyzed as a three-dimensional problem, and stress and deflection calculations are based on flat plate theory (Adler and Sun, 1976). The confined-core theory (Wilson, 1972) hypothesizes that within a typical pillar, two regions exist: a confined-core region where the horizontal confining pressure is uniform and approximately equal to the overburden pressure, and a yield zone where the vertical pressure increases from nearly zero at the rib to a pressure peak at the boundary of the yield zone. The strength of coal in the yield zone ranges from nearly zero at the rib to nearly full strength at the confined core. The vertical stress in the confined core decreases from maximum at the yield zone boundary to the overburden pressure some distance into the pillar. Excavation of the adjoining entries

Jan 1, 1986

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL HYDROLOGIC REGIME The total hydrologic cycle must be considered when evaluating potential ground water problems in a mining environment. Precipitation is the ul¬timate source of all surface water and essentially all ground water. Stream flow during low flow periods often orig¬inates as seeps or stream gains (base flow) where the water table intersects the land surface. A stream that is higher in elevation than the ground water system may lose flow, thereby recharging the ground water system. The magnitude of stream gain or loss is dependent upon the hydraulic conductiv¬ity and related properties of the underlying hydrostratigraphic units. Ground water moves constantly from recharge areas to discharge areas (streams and springs) usually at very slow rates. Large quantities of ground water may be in¬tercepted in many underground mining environ¬ments. Construction of an underground mine in saturated formations may encounter ground water inflows ranging from very small to very large and from continuous to intermittent depending upon the hydraulic properties of the hydrostratigraphic units penetrated. SURFACE WATER VARIABLES Precipitation occurs in different forms, varying amounts, and with a wide assortment of temporal and areal distributions in the various mining dis¬tricts within the United States. Mine inflow can be affected in a matter of hours by precipitation events where there is a direct hydraulic interconnection between the mine and the surface through fractures or a mine opening. The timing, form, amount, and distribution of precipitation should be evaluated in a mine inflow study. A portion of the precipitation that falls in a topographic basin moves as sheet flow to runoff channels (Fig. 1). Some of the precipitation infil¬trates the unsaturated soil zone where it can either move laterally as interflow to the surface system to augment stream flow or move downward as re¬-charge to the ground water system. The unsatu¬rated zone (called the zone of aeration or vadose zone) can range in thickness from essentially zero to a few hundred feet. The saturated zone or ground water system occurs below the water table (zone where hydrostatic pressure is greater than atmos¬pheric pressure) where all the pores are filled with water (Freeze and Cherry, 1979, p. 44). Moisture can be lost from any of the systems (surface water system, unsaturated zone, and ground water sys¬tem) by the processes of evaporation and transpir¬ation which return moisture to the atmosphere. Stream flow consists of runoff and interflow components plus an additional base flow compo¬nent (Fig. 2). Base flow constitutes ground water discharge to a stream. Base flow plays an increas¬ingly significant role as total stream flow declines. Base flow is important because it constitutes much if not all stream flow between periods of precipi¬tation when runoff and interflow have largely dis¬sipated. INTERACTION OF SURFACE WATER AND GROUND WATER SYSTEMS Recharge from a surface water system to ground water systems can occur via unsaturated or saturated flow. The amount of recharge is depen¬dent primarily upon the vertical hydraulic conduc¬tivity of the formations underlying the stream and the availability of water. Streams that flow over low hydraulic conductivity formations lose little water even if the ground water levels are significantly lower than the stream. A ground water system may contribute flow to a surface water system but nor¬mally only by saturated flow. This contribution usually takes the form of seeps, springs, and the base flow of streams. GROUND WATER VARIABLES Introduction The variables that affect ground water flow are discussed in increasingly complex theoretical situ-

Jan 1, 1986

By Andrzej Frycz

The development of the theory of reliability creates more and more possibilities of its application in different domains of technics. The methods evolved to date, both theoretical analysis of the engineering systems and investigations techniques in practice can be put in use a d translated from one science to another one [1,3,7J . It needs to consider the specific of the different sciences. But it is necessary to take account of the specific characteristic of each line of science. The reliability investigations needs, justified in technical and economical viewpoint appear too in mine ventilation technics and systems. The mine ventilation system is a complex of workings and ventilation plants, which serve to supply the networks with a sufficient quantity of fresh air from the atmosphere and then carry off the vitiated air. The condition necessary for a ventilation system to perform definite task is the correctness of all its elements, that is a capability to preserve in a expected range of tolerance, the values of basic parameters. The element of a system which ceases to work correctly is called failed. The basic parameter of all elements of a ventilation system is the characteristic curve, pressure loss - air quantity relation ?p = f(Q) (1) This curve concerning the workings and ventilation stoppings is given by the formula: ?p = R Q2 (2) thus the resistance R (of the workings or stoppings) may be taken as a characteristic parameter. The course of this characteristic f(Q) will be given in a complex form in concern with fans, ejectors, air curtains. The failure of a ventilation plant or working is therefore an event, relying on a change of its characteristic, thus for a definite time the losses of the plant's or working's capability set in for the fulfilment of its function in the ventilation system. The failures are divided in viewpoint of their nature on sudden and progressive. We are in concern with the sudden failures which are characterised by a violent change of the ventilation element parameter for example a fall of roof, or silt up of the working, opening or failure of the ventilation stopping, the stand-off of the fan or ejector etc. We distinguish two kinds of failures on the viewpoint of their action on the air flow: the "opening" failure and "closure" failure. The prevalence of factors, which causes the failures is in connection with the intersection in the mine of roads of haulage, roads of underground transport of materials and lining elements, roads of people motion with airways, as also depends on the rock pressure reaction on the workings lining and plants placed there. Other factors will yet be decisive upon supply decay of fans, ejectors and curtains. The appearance of failure of the ventilation element is therefore of random nature and determines the change of the element, when it is passing from operating state to unoperate. Qualifying the ventilation system element to one of these states is easy, when the characteristic change is clear and occurs suddenly, that was assumed. The investigations conducted by Patrushev and Karnaukh [91 in concern with the ventilation stoppings resistance change in the case of their opening, had shown the possibility of resistance value change in the range of several hundreds higher.

Jan 1, 1980

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By L. Alagha, F. Schott, M. B. Haya, Z. Xiao, K. C. Monyake

"Froth flotation is a process in which valuable minerals are separated from gangue minerals on the basis of surface wettabilities. It is a universally accepted process for the beneficiation of coal. The large amount of coal fines that have been generated from both mining and beneficiation processes has been reported as a chronic problem to both fine coal preparation and utilization as these fines contain a high amount of ash forming minerals. The current study investigated the potential application of Synthetic Bio-compatible Polymers as slime depressants in fine coal flotation for the possibility to enhance the combustible recovery and ash rejection. Raw coal samples containing 21% of ash-forming minerals were crushed, grinded and floated in the presence of Chitosan polymer. Flotation tests were carried out in D-12 Denver flotation cell with 1-Liter capacity. Flotation outcomes were studied as a function of polymer concentration. Box-Behnken factorial method was used for experimental design. Second order response functions were produced for ash% and combustible recovery. The results obtained from this study demonstrated positive influence of chitosan polymer on ash% and combustible recovery. Ash % was decreased by 3.32 % while an increase of 48.15 % in combustible recovery was observed when chitosan was introduced in the flotation process. INTRODUCTION Froth flotation is a widely used method of separating minerals by utilizing the difference between surface wettabilities [1], [2].Modern mechanized mining and ore handling operations produce large amounts of coal fines which in the past were not processed but discarded as waste[3]. Even though flotation is the best method of beneficiation for coal, it can be challenging in case of fine coals. In fine coals, slime coatings of colloidal mineral matter exist on the coal surface. These coatings render the coal hydrophilic, hence reducing flotation efficiency and recovery. Of late, different researches have been using biodegradable polymers to determine their feasibility in enhancing fine coal flotation efficiency[4].Naturally occurring and synthetic polymers, for example, polyacrylamide-based polymers, have been widely used in flotation as multifunctional reagents[5],[6],[7]. Hybrid polyacrylamide polymer has been successfully used as a depressant for ash forming minerals in fine coal flotation[3]. Recently, chitosan has been successfully used in flocculating quartz particles to produce faster settling rates of fine tailings [4]."

Jan 1, 2018

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.' In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By Donald Hulse

"Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them…” (Agricola, 1556). In 2016, it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate.“Most commonly, the social license to operate (SLO) is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat, 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders (Bice, 2014).”A generation ago we learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three-legged stool is a very stable structure (Fig. 1).In 2016, it seems that we have added some other legs to the stool (Fig 2). The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code) addresses “social, and governmental factors…” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves.”The Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Guidelines refer to “environmental, legal and social data…(CIM 2003).”Compared to these, the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the competent person.When there are more than three legs on the stool, it is imperative that all legs be constructed exactly to the design. Any one or more legs that are out of alignment will cause the stool to wobble.Engineers are trained to create designs to meet specifications. Loads can be estimated, forces calculated and cost studies completed that will lead to, not only a stable design, but the most efficient design that meets the specifications."

Jan 1, 2015

By Jurij Karlovšek, Marko Žibert, Scott Keniston

"SUMMARY The importance of information management was recognised in surface construction industry decades ago, and has increasingly being recognised through formal process and laws. Around the world, these laws and codes of practice are currently being drafted and enacted, to reflect the development of software tools and corresponding increasing adoption by industry. This paper deals with specifics of implementing information modelling in tunnelling business utilising BIM (Building Information Modelling) technology developed for buildings as well as similar technology developed for mining industry. Although BIM is recognized initially as a 3D digital representation of physical and functional characteristics of a facility, the real benefits come when complex capability through construction sequencing and even detailed programming (4D) and cost capabilities (5D) are included. INFORMATION MODELLING The Architecture, Engineering and Construction (AEC) industry requires the production of design and construction information, which involves the input from several teams. The tasks allocated to each team need to be carried out in a particular order and coordinated in order to benefit all those involved and the project itself; this is known as “collaborative working”. To ensure the quality, and guarantee that information can be used without change or interpretation, working processes and standards needs to be agreed upon or else it will hinder collaboration and have a negative impact on project delivery. Case studies show that the additional capital delivery costs due to uncoordinated, inaccurate and ambiguous information amounts to 20-25%. The solution to overcome these problems and improve collaborative working in a project is the adoption of BIM. It is a modern approach to the design, documentation, delivery, and life cycle management through the use of project information databases coupled with object-based parametric modelling. BIM requires traditional practices shifting from simple drafting to using 3D native models for building design environment. Additionally, it requires that models are equipped with information that has been traditionally decoupled in a text or other kinds of documents. The goal is not in creating a 3D graphic representation of design intent; rather, it is a comprehensive information management tool based on the simulation of design and construction build around a central repository."

Jan 1, 2016