Search Documents

By Karl E. Elers

The term "potash" denotes a family of minerals and compounds of potassium, containing greatly varying percentages of that element. In commercial usage, most of the potash products are used in agriculture, where they are used to furnish potassium, one of the three basic elements for plant growth; the other two being nitrogen and phosphorus. Potassium's contribution to plant life is principally as a stalk strengthener, and if soils can no longer supply this basic element, then crop failure is inevitable without nutrition supplied from fertilization. While agriculture uses some 95 per cent of the potash produced, other industries require highly refined potash, for the manufacture of soaps, dyes, pharmaceuticals, synthetic rubber, insecticides, photographic film, and other products. Until the mid-nineteenth century, world agriculture had three options related to the potash content of soils: 1) crop rotation and pasturing to attempt to minimize the loss of potash in harvesting, 2) abandoning depleted and exhausted soils (part of the reason for the vast migration of populations in Europe and Asia), and 3) burning forests for the use of the ashes, and concentrating the nutritional value by boiling the ashes in large kettles, for "pot - ash". With the discovery in the mid 1800's and exploitation of potash from underground deposits in Germany, the beginning of the modern potash industry was established, but American potash requirements remained substantially dependent on German production until the 1920's, when oil drilling in the Permian Basin of New Mexico

Jan 1, 1972

By Dieter Loh, Mathias Knoll, Florian Werres

When a new tunnelling project starts, it has been a vital tradition for decades to cast and erect master rings horizontally on a flat surface to demonstrate the compliance with dimensional tolerances. Some tenders ask for the erection of two or even three rings upon each other or repeated master ring erections at intervals throughout the project. Especially for large diameters, this is a challenging and risky task for the workforce in the segment factory. A truck-mounted crane is often necessary, and in some cases it can take up to a week to complete a master ring. The concept of virtual rings has the potential to replace this tradition by assembling master rings digitally instead of physically. This is based on a best-fit approach, considering the 3D coordinates from laser tracker measurements of segments or segment moulds. Building a virtual ring, a sub-millimeter accuracy can be achieved, the alignment of neighboring circumferential and ring joints observed, and the fit of bolt holes checked. The traditional method, on the other hand, is discussed controversially despite the significant amount of work and risks—particularly as the horizontal position of the ring and absence of gaskets do not simulate the reality in the excavated tunnel. This paper will highlight the technical aspects of virtual rings, as well as their pros and cons, illustrated by a case study from London Thames Tideway where a total of 30 physical master rings could be replaced by virtual rings.

Jun 13, 2023

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By Siddhartha Agarwal

The mining industry collects a significant amount of operational data. However, gleaning useful information from the terabytes of data is difficult, and not just because of the sheer volume of the data. Therefore, an automated tool was developed at the University of Alaska Fairbanks to go through data and apply sophisticated statistical and neural network techniques in order to identify the data streams that are important to a process. This paper presents results from the tool as applied to SAG mill data from a gold mine. The results were compared to results achieved earlier with available commercial modeling tools. The comparison indicates that there was little or no loss in performance by automating the very complicated process of neural network modeling. Therefore, the intent of the exercise, to examine if complicated modeling tasks can be automated, was realized. Mining Engineering, 2011, Vol. 63, No. 12, pp. 52-54. Official publication of the Society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By William H. Engelleitner

Agglomeration by balling in cylindrical or shallow pan devices dates back to the early part of this century. The first sintering tests conducted by Dwight-Lloyd on nonferrous ores included a mixing step for ore, flux and fuel carried out in a deep pan device similar to the balling pans, or discs, presently in use. Further work directed mainly toward sintering of ferrous and nonferrous ores always included a preparatory step, usually referred to as mixing, agglomerating or green-balling of the ingredients. In the late forties and early fifties two methods of particle preparation prior to firing were in general use. In Europe the balling pan was used predominantly, both as a mixer and as a pelletizer. In the United States many pilot plants and semi¬commercial plants used balling drums. When the first iron ore pelletizing plants were built in this country, the most frequently used device for green-balling was the cylindrical drum. At the same time, the pan device was used both in Europe and the United States for many other materials such as fertilizer, cement, flyash, alumina and copper concentrates, as well as to mix the feed for sinter machines. The difference between these two balling devices - -the drum and the disc - has been the subject of much discussion and is well covered by several papers included in the 1962 publication "Agglomeration' issued by AIMS, based on their 1961 International Symposium held in Philadelphia. (1)

Jan 1, 1965

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By A. K. Kelly

Potash was first discovered in Saskatchewan in 1943 but its continuous extraction did not begin until 1962. In the years since then, potash has played an important role in the economic and political life of the province. And, as is well-known, the most eventful time in the life of the industry occurred in 1975 when the Government of Saskatchewan decided to become a major participant in potash production. To understand that decision, however, requires an understanding of the economic development of Saskatchewan and of relations between the industry and the government prior to 1975. This year, Saskatchewan celebrates its 75th year as a province. For most of those years, we have been an agrarian economy and society, dependent on exports of cereal grains, mostly wheat, for a livelihood. Even today, agriculture accounts for about 25% of the province's Gross Domestic Product (Economic Review, 1979, p. 7) and difficulties in agriculture spread rapidly to the rest of the provincial economy. The difficulties and risks that go hand in hand with being a "one crop" economy were known as long ago as 1920 but were not fully appreciated until the combination of depression and drought in the 1930's turned the prairie grain- belt into a dustbowl. Some idea of the severity of the depression is revealed by the following data: in 1928, Saskatchewan produced 321 million bushels of wheat. By 1931, the total fell to 132 million bushels and, in 1937, to a mere 37 million bushels. The value of agricultural products sold off farms fell from $273,000,000 in 1928 to a meagre $51,000,000 in 1937. The impact of such a fall of agricultural incomes was catastrophic since about 70% of the population of some 921,000 persons lived in rural, agriculture-dependent areas (Britnel.1, 1939, p. 14).

Jan 1, 1980

By M. Misra

The dispersion of oily collector has significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. However, such dispersion and reagent addition techniques are invariably inadequate and non-selective. A new collector utilization technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This new technique involves atomization of the collector into the gas stream. Under these circumstances an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the gas phase (continuous with respect to oil) and the gas phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de-facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and most significantly increases the flotation rate of ultrafine coal. Furthermore, atomization of collector/frother combinations yielded improved flotation yields and maintained near uniform froth levels which is a desirable feature in coal flotation. In addition to flotation experiments, microscopic examinations of the attachment of oil-coated bubbles at a coal surface were conducted by attachment-time and contact-angle measurements. The oil coated bubbles attach at significantly faster rates and with a higher contact angle than do oil free bubbles.

Jan 1, 1987

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine (CM) with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. This paper describes the validation of the models based on experimental data and the gas distribution results of the CFD models. INTRODUCTION To control methane gas and dust concentrations on continuous mining operations, it is important to provide sufficient quantity of fresh air from the end of tubing or curtain to the active face. In this region, operating machine-mounted water sprays and fan-powered, flooded bed scrubbers can significantly increase the amount of airflow reaching the face [1-3]. However, when an entry is large, especially in higher coal seams, the water spray configuration and the scrubber capacity may not be adequate to maintain sufficient forward airflow to confine the dust cloud to the face. Dust can roll back toward the machine operator as a result [4]. Currently, several coal mines having negligible gas emissions in higher coal seams (2.4 to 3.0 m [8 to 10ft.] thick) with exhaust tubing systems redirect the scrubber discharge back towards the face in an effort to improve dust collection. NIOSH studied the redirected scrubber exhaust techniques for dust and gas control in a full scale CM gallery to assess its potential for industry-wide application [5]. For a CM face, previous studies have concluded that the behavior of gas and respirable dust is a complex process. The distribution/dispersion and transport of gas and respirable dust after they are liberated at the face are governed mainly by their mass properties, the movement pattern of the ventilation air, and interactions with the mining machine and water droplets created by the external water spray systems used for dust control [6-10]. To understand these behaviors in a complex CM environment and to evaluate the effectiveness of various control techniques, numerical modeling has become a necessary supplement to laboratory experiments and field studies."

Jan 1, 2017

By W. L. Price

I. INTRODUCTION Today, there are two conflicting trends facing the designer of the bulk material handling system. The first trend is the necessity to stockpile increasingly larger amounts of bulk material (coal, ore, stone etc.) as economically as possible. Fig. 1 illustrates such a typical large storage pile. The second trend is the increasing awareness of the ecological problems of today manifesting itself in a new concern over possible air pollution from storage pile surface particles. The conflict between these two trends can become dramatic when this bulk storage pile is located near a heavily populated area. Strong winds can easily create a severe local problem by blowing the particles from the pile surface toward residential and commercial areas, igniting a crisis in public relations. (2), (3), (4). To help define our combined subject and ecological culprit more accurately, Fig. 2 shows the commonly accepted size range of dust particles. A descrip¬tion of the present state-of-the-art of dust control for large storage piles is the intent of this paper. II. OPEN STORAGE PILE SYSTEMS - ALTERNATE CHOICES AND RELATIVE COSTS In discussing the open storage dust problem and possible solutions, one obvious question arises - what are the economics of placing large bulk storage under cover? Part or this answer will be found in Fig. 3 - an approximate unit capital cost comparison between several methods of storage. It will be noted that the cost curve(s) for the closed concrete silo storage illustrated in Fig. 4 is cheaper per ton at relatively small tonnage capacities, but as tonnage increases, the open pile storage unit cost (B) becomes more economical. Curve (T) covers the cost of open storage using the plow feeder arrangement shown in Fig. 5. A gravity draw-down pile with feeders at the base as shown in Fig. 6 represents yet another open storage choice.

Jan 1, 1972

By J. F. Fitzpatrick

This paper examines the cost elements associated with changes to gold mining practice over the last decade that result from the changes in environmental regulation and the heightened governmental and public awareness of environmental issues. The main experience base is Pegasus Gold Corporation's flagship mine, Zortman/Landusky, located in the Little Rocky Mountains of Phillips County, Montana. This operation was among the first mines that were permitted under the 1974 Montana Metal Mining Reclamation Act. In 1974, the Montana Metal Mine Reclamation Act was enacted, creating a permit system for metal and industrial mineral mines for the state of Montana. The act established the content of mine permit applications and defined parameters for the reclamation of mining disturbances. The Act can be viewed as implementing legislation for Article 9, Section 2, of Montana's Constitution, which provides that "all lands disturbed by the taking of natural resources shall be reclaimed." Pegasus Gold Corporation's Zortman/Landusky mine was among the first mines permitted under the new Act. In 1978, the initial permit applications were submitted for Zortman and Landusky, and a full Environmental Impact Statement was prepared by the Montana Department of State Lands; permits were issued in 1979. When opened later that year, the anticipated mine life for the combined Landusky and Zortman operations was approximately 18 years, based upon a proven and probable ore reserve of 43.2 million tons. Zortman/Landusky was the first large-scale heap leach gold mine in the United States. Its distinguishing feature was, and remains, a remarkably low ore grade, now .016 oz/ton. The ore is economic because it requires neither crushing nor agglomerating to leach effectively. Approximately two years after the initiation of the state's regulatory process, the Federal Land Policy Management Act (FLPMA) was enacted, establishing a mine regulatory framework for lands under the administration of the Bureau of Land Management.

Jan 1, 1992

By John W. Stevenson, Ted L. Sartain

Underground booster fan installations are currently employed in hundreds of coal mines throughout the world. Such installations, when properly designed and maintained, have proven to be safe and effective tools to provide desirable airflow volumes on sections or in areas of mines where the ventilation requirements exceed the capacity of the main fan system. In cases where an airshaft cannot be justified due to surface topography, depth of cover, or limited reserves a booster fan can serve the same purpose, be operational in a fraction of the time and at a substantially reduced cost. Booster fans are currently non-existent in U.S. coal mines. This is primarily due to lack of acceptance by the Mine Safety and Health Administration (MSHA), which has failed to acknowledge the merits of a booster fan system. Also, the absence of booster fan provisions in Part 75 of the federal regulations has led to the misconception that booster fans are legally prohibited in U.S. coal mines. In 1986, Jim Walter Resources, Inc. (JWR) developed and submitted to MSHA a plan to install and operate an underground booster fan at the No. 7 Mine. Detailed computer simulations were used to substantiate JWR1s position, that the booster fan could effectively provide the needed airflow on a developing section without adversely affecting ventilation in other areas of the mine. JWR also realized that numerous safeguards and operating procedures were essential for providing a safe system. Thus, safety features such as electrical interlocking, independent power supply, remote atmospheric monitoring, etc., were incorporated into the plan. This paper is a case-study that discusses JWR's proposed plan to install and operate an underground booster fan at No. 7 Mine. Unfortunately, MSHA's continued negative response has prevented implementation of the plan.

Jan 1, 1989

By R. C. Freas

The physical and chemical properties of mica are unique relative to most other industrial minerals. As such, mica is suitable for a variety of functional applications in new and emerging markets. This paper examines some of these applications and particularly the contribution mica makes in end product performance.

Jan 1, 1997

By A. D. Hammond

Until recently, the volumes delivered and unloaded from heap-leaching pads have been estimated by manual methods at Wharf Resources' South Dakota operation. In August 1989, the Engineering Department acquired the MINE-SURVEY software developed by GEM COM Services, Inc. of Vancouver, Canada, as part of a mine planning/grade control software package. The implementation of MINE-SURVEY for pad control resulted in a cost-effective tool to provide accurate and prompt estimates of ore delivered or unloaded from the pads. Volumes can be calculated in a matter of minutes as opposed to hours or days. Another benefit is the ease of comparison of as-build and designed volumes, plotting cross-section in any orientation, importing into AUTOCAD, validation of ore densities and truck factors. This paper describes the application of the MINE-SURVEY systems in heap leaching pad volumetrics.

Jan 1, 1991

By RICKARD HANSEN

With vehicles frequently found in mines and tires being a major fuel item, the risk of tire fires will be severe underground. This study presents an analysis of tire fires on mining vehicles to increase the knowledge of the risk and mitigating measures, which would improve the fire safety underground. Data from fire experiments and computational fluid dynamics (CFD) simulations were applied. It was found that the wheelhouse of a loader caused an increase in the flame tilt angle, decreasing the flame impingement and heat flux downstream. The flame temperature of a drilling rig tire was found to be higher than that of a loader tire, increasing the risk of igniting items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for a drilling rig for higher flow velocities, indicating the influence of the wheelhouse/mudguard construction and tire geometry on the flame tilt angle. The construction of a loader resulted in flow behavior, where the short distance to the front mudguard/tire and the separation of flow directly downstream of the construction led to gases being steered past the front mudguard/tire. In a drilling rig case, the longer distance to the front mudguard/tire led to gases being directed toward the body of the vehicle after passing the area with flow separation.

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By V. O. Tenorio, A. M. Sanzana

"INTRODUCTION This report summarizes a research about mines which are transitioning from surface to underground mines. It is a guide to make strategic decision in these increasing amount of mines. Capital and operating costs are linked with major strategic decisions in the exploitation of an ore body. This is the reason to analyze costs related to this transitioning world trend. There are multiple reasons for transitioning from Open-Pit (OP) to Underground (UG) mining. The primary economic incentive for going UG is that the cost per unit of ore from OP mining eventually exceeds that from UG extraction. This is due to the excessive amount of waste that must be extracted when the depth of the pit increases. In addition, the reduced footprint of UG operations contributes to diminish the environmental impact on the surface. Furthermore, it becomes more difficult to find new, easily accessible ore deposits. Then, a cost model helps to guide strategic decisions in the transition from OP-to-UG mines. Objectives • Propose a methodology to guide strategic decisions in the transition from OP to UG mining. • Create an integrated cost model based on existing OP and UG individual cases. • Identify and characterize a group of mines transitioning from OP to UG. • Analyze operating and capital costs of a particular transitioning from OP to UG mine. MAIN CONCEPTS Open Pit Mining (OP) The main decisions in OP mines are: Cut-off grade, Stripping Ratio (SR), equipment size, stockpiling, pushback sequencing and processing capacity. The stripping ratio is measured as the tonnage of waste required to be removed to reach and extract one tonne of ore. The material extracted from an OP exploitation can be classified as waste and ore. This classification depends on the cut-off grade. The cut-off grade indicates the minimum amount of material with economic value in a block. The waste from the mine is going to the waste dump and the ore is going to stockpiles where will be store and then going to the processing plant (leaching or concentrator). The waste of this process is going to the tailing pond big pools. And the product is sell in the market. Another important issue is the mining capacity which is going to define the investment in mining equipment. Underground Mining (UG) The first decision to be made in order to open an underground mine is selecting the mining method. Caving methods are the more productive and have lower operating costs. There are three caving methods: Block Caving (BC), Panel Caving (BC) and Sublevel Caving (BC). The access development could be an horizontal adit or a straight or downspiral decline. A shaft could be used for inclined or vertical access. Other key issues are: equipment capacity, cut-off grade and production sequencing."

Jan 1, 2016

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By Regis F. Kopac

With the growing dependence on coal as an energy source, finding a means to prevent or reduce the freezing of coal during winter shipment has become increasingly important. Several chemical companies focused on this problem and applied chemical technology to develop suitable solutions. As a result, a number of freeze conditioning agents have been introduced in the past few years, several of which have been highly effective in controlling frozen coal. The efficacy of these chemicals has been well established, however many users have found that only a well defined program will produce acceptable results at a reasonable cost. Positive program results yielding recognizable benefits have caused many power generating and coking plants to consider freeze conditioning agents. A freeze conditioning agent (or FCA) has been defined as a multi-component organic liquid designed to be sprayed on coal particles at bulk shipping points to assure that receiving locations will be able to unload, store and use the treated coal with minimum delay or inconvenience. The chemicals are generally applied at rates of 1 to 2 pints (0.473 to 0.946 liters) per ton and normally function by changing the crystalline structure of water left on the coal during processing. The bond strength of the ice that may subsequently form is markedly reduced. Instead of freezing into solid, unmanageable masses, the coal can be easily unloaded by rotary dumping or the opening of hopper car doors.

Jan 1, 1980

By Alexander N. Winchell

"Location. The iron formation of the Gogebic district (including the Penokee) comprises a narrow belt south of the western part of Lake Superior extending from Michigan for a considerable distance into Wisconsin. From the mouth of the Montreal River (about twenty-five miles west of Ashland) the iron formation is only about twelve miles distant, but it is about twenty miles south of Ashland. Beginning on the east at a point about eight miles east of Wakefield, Mich., it extends through Sunday Lake, Bessemer and Ironwood in Michigan, and thence south of west through Hurley, Wis., and only a short distance south of Mellen, Wis. About eight miles westward from Mellen, the formation disappears, but six miles further west it is known to reappear and continue thence for about eight miles. The total length of the range is about sixty miles, two-thirds of this distance being in the State of Wisconsin; but nearly all of the ore has been obtained from the eastern third of the district, which is in the State of Michigan.History. This iron range was first noted in 1848 by Dr. Randall, assistant geologist to Dr. David Dale Owen, while following the fourth principal meridian northward. It was also reported by Charles Whittlesey in an account of a survey made in 1849, and published by Owen in 1852. Analyses of the iron ore are given with the following account. ""The bed of magnetic iron ore south of Lac des Anglais is of extraordinary thickness,25 to 60 feet. * * In the wild and deep ravines where the Bad River breaks through the range, there is a cliff of slaty ore * * * probably three hundred feet thick. * * * I estimate more than one-half of this face to be ore, and in places the beds are from ten to twelve feet in thickness, with very little inter-mixture of quartz * * * . The position of the best exposures of ore which I saw is such as to require from eighteen to twenty eight miles of transportation to reach the lake."""

Jan 1, 1920