Search Documents

By Z. Yanni, W. Xuan, Z. Jingyu, D. Jun

"In order to conserve the coal resources, many coal mines which have been mined begin to re-mine. Re-mining face is of complicated circumstances and coal spontaneous combustion is unknown, so experiments are designed to study the characteristics of multiple oxidized coal samples. The investigation into the oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. The non-caking coal is collected as coal samples. The raw coal sample with initial oxidation and the sample after second oxidation and third oxidation are obtained after a certain treatment of the coal. The temperature-programmed system, and proximate and ultimate analysis are adopted to compare the releases of gaseous products of spontaneous combustion characteristic parameters of the multiple oxidized coal sample. With the increase of oxidation times, experimental results indicate that the oxygen consumption rate, the release rate of carbon monoxide and the intensity of heat release are significantly decrease. The characteristic temperature dropped and the size of the pores in coal is smaller as well. INTRODUCTION China accounts for 13% of global coal resources [1-2]. In recent years, more and more coal mines begin to re-mine in order to conserve resources. This production mode is to mine coal pillar left by last exploitation or unavailable for mining. In the process of slicing mining for coal seam groups or thick coal seams, the second or multiple oxidation due to the mining-induced effect, may take place in the goaf of the lower seam. So the spontaneous combustion is prone to occur in this area. The study on oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. Scholars [3-7] have discussed the workability of re-mining for coal mines, verify the feasibility of the existing mining technology for re-mining area, and set up the prevention measures of coal spontaneous combustion. But all these measures are only based on on-site observation data, instead of experiment on spontaneous combustion characteristic parameters of re-mining coal samples which have a great importance for early prediction and forecast. The authors aim at investigating the multiple-oxidated coal spontaneous combustion law, and perfecting the coal spontaneous combustion mechanism to provide a basis for the prediction and forecast."

Jan 1, 2015

Over the years, numerous studies have been conducted to characterize the floatability of coal pyrite. Unfortunately, many of the results obtained using isolated samples of coal pyrite are not directly applicable to actual coal flotation systems where liberation and entrainment may be the major factors affecting pyrite rejection. In this paper, the association of pyrite with other coal constituents is investigated, and the data are presented for feed and product streams obtained from release analysis tests. Release analysis is used to minimize the effects of entrainment. Particle distributions for each stream are presented as functions of size and composition in order to discern the behavior of free and composite particles.

Jan 1, 1992

By J. T. Carlson

Dolomite [CaMg(CO3)2] is an intolerable impurity in phosphate ores, due to its MgO content. The need to develop a cost-effective method for the removal of dolomite from high-MgO phosphate ores becomes increasingly important as high-grade reserves become depleted. The jigging process has been investigated as a method for the beneficiation of phosphate ores. A laboratory-scale jig was constructed and tested using a semicontinuous, ?through-the-screen? jigging process. Two types of sedimentary phosphate ore were used; a sample from Plant 1 in the 4.00 x 0.85-mm size range, containing 1.55% MgO, and a sample from Plant 2 in the 3.40 x 0.85-mm size range, containing 3.07% MgO. These were tested, using previously optimized jigging parameters, at high and low feed rates. For the Plant 1 phosphate ore, a phosphate concentrate that contained 0.89% MgO was achieved with a bone phosphate of lime (BPL) recovery of 32.0%. For the Plant 2 phosphate ore, a phosphate concentrate that contained 1.38% MgO was achieved, with a BPL recovery of 74.7%. Minimum achievable MgO grades were also determined by analyzing hand-separated phosphate samples.

Feb 1, 2012

By Y. Luo

Cuando se diseña y operan minas de carbón subterráneas con el método de cámaras y pilares, es siempre difícil obtener un buen equilibrio entre la prevención de subsidencia de la superficie y la obtención de un alto coeficiente de recuperación. En este trabajo se propone una metodología de diseño aplicando la teoría de arco de presión y se detallan los principios y modelos matemáticos involucrados. Se desarrolló un programa de computadora a fin de realizar el proceso de optimización del diseño y fue aplicado a la examinación de un caso documentado en el que había sucedido una falla masiva de un pilar en cascada sobre un área grande en una mina de carbón poco profunda. Los resultados indican que el método de diseño propuesto puede ser aplicado para prevenir la subsidencia y a la vez obtener un alto coeficiente de recuperación para operaciones mineras de cámara y pilares.

Jan 1, 2014

By Achille Balossi Restelli, Elena Rovetto, Andrea Pettinaroli

"The Station “C13” of Warsaw Underground Line II, with tunnel crown 10m below the water table, required the excavation of three connection tunnels, underpassing a six-lane in service road tunnel, working from two lateral shafts. After the collapse occurred while digging the first tunnel, the use of artificial ground freezing was chosen to ensure the excavation under safe conditions. A complex freezing pipe geometry and excavation sequencing was necessary because of the interferences of the overlying road tunnel diaphragm wall foundations, shaft internal structures and previous grouting activities. A combined freezing method was used: nitrogen for freezing the tunnel arches, brine for freezing the intermediate wall and for maintenance stages. Sandy and silty sandy layers were frozen around the crowns and sides. No treatment was necessary for the inverts, lying in clay. A monitoring system of ground temperatures and structure movements allowed for successful completion of work in 8 months. INTRODUCTION The C13 Station of the Warsaw Underground-Line II is located on the West bank of the Vistula River. It consists of two shafts and three connecting tunnels, passing under the Wislostrada (WS) Road tunnel. According to the initial geotechnical investigation, tunnels should have been excavated in high-plasticity clay, but during the first borings non cohesive soil was encountered. Additional investigations were performed on both shafts and a more detailed stratigraphy was reconstructed (Lombardi et al. 2015). Layers of fine sand, sandy silt and sandy silty clay were present along the tunnels crown arches and in the North East tunnel they extended down to the centre line (-13.735m above the Vistula River medium level). Based on the new stratigraphy, it was decided to stabilize the crown and control the groundwater inflow from the face with jet-grouting columns extending the treatment down to the clayey soil, but a collapse occurred in the North West tunnel with soil and water inflow inside the shaft."

Jan 1, 2016

By K. N. Han, H. C. Cho, R. Kim

"A comprehensive analysis of the effect of OH- on various cations in hydrometallurgical systems has been investigated. Cations chosen for this analysis included groups 1A and 2A, rare-earth elements and other common transition metal ions such as Cu2+, Fe2+, Fe3+, Mn2+, Ni2+, Co2+, Ag+, Cd2+, U4+, UO2 2+, Hg2+, Al3+ and Zn2+. The Newton-Raphson technique was used to calculate and plot various metal species over a wide range of pH. This study has clearly shown that by adjusting the concentration of OH-, the separation of Fe from Mn, U from V, Ce and Eu from other rare-earth elements, and In from Sn is possible. The effects of hydrated metal ions on the separation and removal of various metals from each other under various conditions is discussed.IntroductionThe primary purpose of hydrometallurgical processing is to extract, remove and purify various metals from diverse sources. Hydrometallurgists are frequently preoccupied by the extraction of cations in metallic form, but overlook the important role anions play in such processes. A proper choice of anions can determine the fate of successful extraction, removal and purification of metals (Esmaeili et al., 2005; Brbooti et al., 2011; Wei et al., 2005; Jeppesen et al., 2005; Al-Tarazi et al., 2004), and also separation (Farha et al., 2011; Sevenich and Fritz, 1983; Rashid, 1974) of cations from various solutions.In this study, the authors have examined some of the effects that anions play in various solutions. The anion considered in this study was the first hydroxide, OH-. Other anions, such as Cl-, Br-, I-, and CN-, will be dealt with in the second part of the series of two papers."

Jan 1, 2015

By C. J. Roos

Ground-engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these "consumable" items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corp. to predict the consumption of excavator teeth at a particular mine site. This paper presents the results of the Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2010

By A. Toulet

Mining in Mexico has an immensely long tradition. In his first letter reporting to his sovereigns from Mexico in July 1519, Hernan Cortes wrote, "To our mind it is probable that this land contains as many riches as that from which Solomon is said to have obtained the gold for the temple ... " 1 But not only precious metals drew his attention; in 1524, short of tin needed for casting guns, he found it in Taxco. As an added bonus, those who went to find it "came upon a vein of iron which according to experts is of exceeding richness." 2 Since then, the mines of Mexico have yielded up enormous amounts of mineral and continue to do so. Mexico is one of the ten principal producers of minerals world-wide both in production volume and diversity. 3 Tens of thousands of tons of iron, sulphur, and coal come from its earth annually; it is the world's second largest producer of barite; third of antimony, fluorite, and graphite. 4 Copper, zinc, silver, molybdenum, arsenic and cadmium and others are wrested from its mines. The wealth is there; but maximizing its potential requires investment, technology, and markets that the government cannot itself provide. Thus mining, since the Mexican Revolution severely restricted by both law and policy, today looks to private investment to develop its potential. Beginning in 1989, Mexico's government cautiously moved to liberalize private sector involvement in mining; 5 using the experience gained from these initial regulatory changes, the current new Mining Law was adopted in 1992 6 and new Regulations were promulgated in 1993. 7

Jan 1, 1994

By T. E. Wilson

In conjunction with experiments to improve the particle size preparation of coal bore cores prior to washability testing, discrete-event breakage of coal, shale and homogeneous low-strength concrete cores was studied. Breakage of individual size classes by drop-shatter and by incremental tumbling in an end-over-end hand-driven tumbling cylinder revealed systematic changes in the breakage function, namely, that breakage in any size class diminishes as the number of events increases. The effect of the fines removal enhances the breakage of harder material (having lower grindability indices), but appears to have less effect for softer material.

Jan 1, 1998

By H. Staton, N. Michaelson

"INTRODUCTION Lundin Mining’s Eagle Operation, located in Marquette County, upper Michigan consists of a mine and concentrator that process a Ni-Cu-(PGE) ore. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 66 miles to the Humboldt mill where both nickel and copper concentrates are produced. Operations began in 2014 and continued with an average production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year for the first three years of operation. The Humboldt Mill, currently operated by Lundin Mining, processes the nickel/copper ore from Eagle Mine and performs the concentration through several stages of flotation. Originally built in 1954, the Humboldt Mill began operations as an Iron Ore processing facility, and was converted to a gold processing plant during the 1980s. Various groups owned the site after closure of the gold operation. Eagle purchased the Mill in 2008 and invested more than $280 million to clean up historic mine waste and refurbish the plant (see flowsheet in APPENDIX). This paper will overview the ramp-up of the operation, and discuss some specific areas that went well and some that could have gone better during the design phase. HIGH LEVEL DESIGN CRITERIA Coarse ore arrives from the mine and is stored in a building with a capacity of 10,000 tonnes. Ore is crushed in three stages to a final product size of 100% Passing 12mm. Crushed ore is conveyed to the mass flow fine ore bins, which have a live capacity of 3000 tonnes. Crushed ore is fed to two parallel 900 HP ball mills, charged with 3” high chrome grinding media, and ground, in closed circuit with hydrocyclones, to a p80 of 110 microns in the flotation feed. Soda ash is added to the mills based on process water hardness. Cyclone overflow passes to the bulk conditioner where Sodium Isopropyl Xanthate (SIPX) and Methyl Isobutyl Carbinol (MIBC) are added. The slurry is pumped to the rougher bank for bulk flotation. Rougher concentrate is fed to a 500HP vertically stirred regrind mill and is ground to a p80 of 50 microns, using 5/8” high chrome balls. Rougher tailings report to the tailings thickener. The regrind cyclone overflow is sent to the single stage cleaner bank followed by two scavenger banks. The cleaner concentrate is pumped to the copper-nickel separation circuit. Cleaner tailings report to the tailings thickener. In the copper-nickel separation circuit, the pH is raised to 11.5 and a copper concentrate is recovered from the bulk cleaner concentrate in two stages, namely the copper roughers and the copper cleaner columns. The concentrate from the copper flotation columns is the final copper concentrate. The tailings from the columns return to the head of the copper-nickel separation. The nickel concentrate is the copper rougher tailings stream."

Jan 1, 2018

By S. N. McIntosh

Column bioleaching was evaluated by the U.S. Bureau of Mines as a means of recovering manganese from a low-grade ore from the Three Kids deposit in Southern Nevada. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms. Diluted molasses medium was provided as nutrient for the microorganisms. The medium was recirculated through the ore bed until the sugars were spent. Two methods were evaluated to recover manganese from the sugar depleted bioleaching solution: (1) adsorption with a weak cation exchange resin followed by stripping and precipitation techniques, and (2) direct precipitation of the manganese using ammonium carbonate. Both methods removed up to 95 pct of the solubilized manganese from the medium as a carbonate salt. After manganese removal, the medium was replenished with fresh molasses and recycled back through the column. More manganese was effectively leached. This process of manganese solubilization and recovery followed by replenishment and recycling of the medium was repeated until 98 pct manganese was extracted from the ore.

Jan 1, 1993

By Raymond A. Bradbury

A significant news item appearing in a coal mining journal in November 1969 stated simply that a Caterpillar D-333-CNA engine had received Bureau of Mines Schedule 31 approval. This item occurring at the time a new mining property in Martin County of East Kentucky was being prospected and prepared for mining, resulted in the manage-ment of Martin County Coal Corporation asking the question, "Why not use diesel equipment in our new operation?" Martin County Coal Corporation is part of the A. T. Massey Coal Company, Incorporated organization. The property being developed is on a 17,500 acre leasehold obtained from Pocahontas Land Corporation and lies in the Wolf Creek area of Martin County. The Norfolk and Western Railway Company built a 24-mile railroad into this undeveloped section of Kentucky to tap a huge reserve of steam coal. Duke Power Company is the customer who will take all of the production from Martin County Coal Corporation mines which ultimately is projected to be 2,000,000 tons annually. Four coal seams, all above drainage, are included in the lease. The Middle Coalburg and Stockton are being deep mined now and it is in those mines that the diesel haulage equipment was introduced. This paper will endeavor to trace the steps loading to the introduction of the first diesel-powered Wagner Mining Equipment Company ScoopTram in a coal mine in America. It will further elaborate on the features which make this unit a very versatile and useful utility unit as well as the safety features which are incorporated in the machine. The success of this first unit led to the placing of

Jan 1, 1972

By R. Shields

"Hard rock mines move large volumes of material. But the conveyors essential to this movement suffer lots of problems, including carryback, spillage, dust, and belt wander. Many of these issues are created at the transfer points where the belts are loaded. This presentation will start with an overview of the latest transfer point systems that incorporate safety and serviceability by design. It will then report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, Nevada. Here performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine. THE IMPORTANCE OF TRANSFER POINTS Conveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance are the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created. The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material—cargo released in the form of carryback, spillage, or airborne dust—that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems, and issues with community relations. As estimate attributed to the U.S. Mine Safety and Health Administration (MSHA) notes that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points. TECHNOLOGIES TO IMPROVE TRANSFER POINTS A number of techniques to improve the performance of conveyor transfer points have been developed. They include: • Absorbing impact, to prevent damage to belt, belt support systems, and conveyor structure, and reduce spillage caused by the impact energy arising from long material drops or large lumps of material loaded onto the receiving belt. • Stabilizing the belt line, to eliminate sag that allows spillage and encourages material entrapment that can damage the belt. • Protecting the skirtboard seals, by sheltering the sealing strips from the mass of cargo pushing material toward the edges of the belt. • Using self-adjusting, multiple-barrier edge seals, to keep material on the belt by providing long-lived seal efficiency with minimum maintenance requirements. • Controlling and centering the belt’s path, to eliminate belt wander and the spillage and damage it can cause. • Allowing dust to settle, through the incorporation of chutework that provides expanded stilling zone and the use of dust curtains at the points where the belt enters and exits the transfer. • Adding supplemental dust control systems, through the installation of systems for passive dust gathering, water-based dust suppression, and/or active dust collection."

Jan 1, 2017

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By M. Beale

Fuzzy logic and neural networks are new technologies being applied in many areas of engineering and business. While it is not always clear which kinds of problems are best suited to these technologies, and which problems are best approached with more standard methodologies, both fuzzy logic and neural networks appear to show great promise in the field of control systems. This paper demonstrates two advantages that these technologies offer: Easy controller design in the absence of a mathematical model of the plant to be controlled, and adaptive control capable of quickly responding to changes in the plant.

Jan 1, 1994

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion-resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Jan 1, 1997

This paper summarizes the process development behind the design of three different types of paste fill plants at operating Canadian hard rock mines. Each application has a unique paste backfill mix and process which utilizes the materials economically available to the mine site. The different plants produce paste fill composed of base metal tailings, a blend of recovered disposal pond tailings fines and alluvial sand, gold ore tailings, and a blend of gold ore tailings and alluvial sand. This work has led to the joint development by Inco and GL&V Ontario of the compaction storage mechanism for the de-watering of mill tailings to a paste consistency.

Jan 1, 1994

By J. Hunter

The Highland Uranium Project in Wyoming is an in-situ leach (ISL) facility owned and operated by Power Resources Inc. It is the largest uranium producer in the U.S. and the largest uranium producer by ISL in the western world. With its limited capital investment and low operating costs, the ISL technique has been demonstrated to be an effective and environmentally sensitive method for recovering minerals from these low grade and otherwise uneconomic orebodies.

Jan 1, 1996

By Y. Luo

In designing and operating underground room-and-pillar coal mines, it is always difficult to achieve a good balance between preventing surface subsidence and achieving high recovery ratio. In this paper, a design methodology applying the pressure arch theory is proposed, and the principles and mathematical models involved are detailed. A computer program was developed to carry out the design optimization process and was applied to the examination of a documented case in which a massive cascading pillar failure had occurred over a large area in a shallow coal mine. The results indicate that the proposed design method can be applied to prevent subsidence while achieving reasonably high recovery ratio for roomand- pillar mining operations.

Jan 1, 2014

By Peter C. Finlayson

Rapidly rising gas and oil prices and the falling quality of coal is forcing energy users in many parts of the world to consider the application of low grade fuel, particularly coal, for steam raising and power generation. However, the use of such low grade coal is normally resisted by the consumer because of operational problems associated with high ash content, sulfur emission and, in some instances, slagging problems caused by low melting temperature constituents in the ash. Recently developed technology involving 'fluidized bed combustion' offers a potential solution to these operational problems. Much of the early work was conducted in Britain, where rig tests were commenced during the early 1960's. This has led on to the successful conversion and operation of a fluidized bed fired industrial boiler at the Renfrew works of Babcock & Wilcox Ltd. Orders for the first commercial boilers incorporating this technology have recently been announced. Significant development work on fluidized combustion is now being undertaken in various parts of the world, in particular North America, Germany and Japan, and the first large scale units are under construction or being commissioned. This paper concentrates on the development of the technology in Britain, outlines the reasons for applying fluidized bed combustion and de-scribes its application at atmospheric pressure for steam raising and at elevated pressure for power generation . Coal Processing Consultants is a Partnership between the National Coal Board and Babcock & Wilcox Ltd. of Britain and has been established in order to provide technical advice and economic evaluations on all aspects of coal processing and utilization. In view of the involvement of its Parents in the development and exploitation of fluidized bed combustion technology, Coal Processing Consultants has been retained by clients in various parts of the world to provide expert advice on the application of fluidized combustion for particular coals and project situations.

Jan 1, 1978