Search Documents

By L. Zhou, J. P. Rider, T. W. Beck, J. A. Organiscak, Y. Zheng

The U.S. National Institute for Occupational Safety and Health (NIOSH)’s Pittsburgh Mining Research Division (PMRD) recently developed a series of models using computational fluid dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations in an exhaust curtain working face. CFD models utilizing species transport model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The study illustrates the gas distribution in the slab (second) cut. The following scenarios are considered in this study: 100 percent of the discharge redirected back toward the face on the off-curtain side; 100 percent of the discharge redirected back toward the face, but divided equally to both sides; and 15 percent of the discharge redirected toward the face on the off-curtain side, with 85 percent directed toward the return curtain. These models are compared against a model with a conventional scrubber discharge where air is directed away from the face into the return. The models were validated against experimental data, proving to accurately predict sulfur hexafluoride (SF6 ) gas levels at four gas monitoring locations. This study includes a predictive simulation examining a 45° scrubber angle compared with the 23° angle for the 100 percent redirected, equally divided case. This paper describes the validation of the CFD models based on experimental data of the gas distribution results.

Jan 1, 2018

By Peter Zhang, Daniel Su, Berk Tulu, Bo Hyun Kim, Zoheir Khademian

Over 2,000 shale gas wells have been drilled in the Pittsburgh Seam longwall reserves. As longwall panels are laid out, some of these shale gas wells must be located in longwall chain pillars. With longwall mining on both sides and the constraint of chain pillar size, gas well in chain pillars are subjected to longwall-induced ground movements and stresses, which could induce deformations in gas well casings Casing deformations are associated with several factors such as overburden geology, surface topography, setback distance, and casing construction. Overburden geology is one important factor that largely determines the locations and levels of deformations in gas well casings Previous NIOSH gas well research has found that casing deformations above the coal seam horizon are smaller under deep cover than unde shallow cover and that casing deformations could occur at the coal seam horizon under deep cover. Recent mine-by cases have provided more insights into the locations and amount of longwall-induced casing deformations as well as the potential occurrence of a large casing deformation at the coal seam horizon. This paper presents three recent mine-by cases with shale gas wells in the chain pillars between two adjacent longwall panels under different overburden depths. Casing deformations were measured by multi-finger caliper surveys and predicted with numerical modeling. With the established numerical model, the effect of overburden depth was further analyzed to investigate the potential occurrence of a large casing deformation at the coal seam horizon under deep cover. These mine-by cases not only provide a general demonstration of how overburden depths can affect longwall-induced stresses and deformations but also give a good indication about the level of casing deformations that could occur under different overburden depths. The study concludes that (1) casing deformations reduce with increase of overburden depths at the gas well; (2) a cementing alternative with production casing uncemented is an effective means to eliminate production casing deformations; and (3) large plastic casing deformation could occur in the production casing at the coat seam horizon under deep cover. The experience and knowledge gained from these mine-by cases would help longwall operators and gaza companies to take appropriate measures to minimize the influence of longwall mining in shale gas wells in chain pillars.

Jun 25, 2024

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By M. De Ladurantaye-Noël, M. Laliberte

Selenium is widely present in the environment at usually low concentration. It is mostly present in the environment at higher oxidation states, i.e., as selenites and selenates (+4 and +6 oxidation states respectively). It is rarely present as selenides (-2 oxidation state) and almost never found as the element (0 oxidation state). Selenites and selenates are generally soluble in water, as such they cannot easily be removed from water by precipitation. Selenites can form insoluble surface complexes with metal oxides such as ferric hydrous oxide and manganese hydroxide, and can therefore be removed that way. However, it is not so common to find selenites in natural environments as it will quickly oxidize to selenate in aerobic conditions. Elemental selenium can also be produced from selenites or selenates by using a reduction process; the end product is a colloid that can be destabilized to be removed from water using the right chemistry. Because of their toxicity, selenides need to be handled with care, and if present, it can form insoluble metal salts or, at low pH, be emitted as H2Se, a noxious and highly toxic gas. The most favorable selenium forms for its removal are therefore selenite and elemental selenium. Organo-selenium species play a crucial part in understanding selenium toxicity. There are a great number of these species. Basically, any organic species that contains sulfur has an equivalent that contains selenium. Of particular interest is the substitution of sulfur by selenium in the two sulfur-bearing amino acids, cysteine and methionine, resulting in selenocysteine and selenomethionine. Methylseleninic acid (CH3SeO2H) is another organo-selenium specie which has been detected in water treated by biological processes and which is biologically active.

Feb 1, 2023

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

By Omid Asghari, Amin Mousavi, Arshad Ranjbar

Geometallurgical modeling of the production benches is an attempt to estimate the geometallurgical variables of the different ore domains, which leads to a better understanding of the ore and its properties. Having geometallurgical variables results in a more accurate prediction of ore characteristics, an improved drilling and blasting operation, and better efficiency of the processing plant. In this research, the geometallurgical variables required for the geometallurgical modeling of the extraction benches are discussed. Then, the relations between Bond work index (BWi), as one of the most important geometallurgical variables and the primary grindability index, and rock geomechanical properties are investigated based on the previously published studies. The BWi is the main parameter for measuring the resistance to the grinding of ore minerals. It represents the energy required for processing (e.g., crushing, grinding) ore rocks in the beneficiation plant. As a real case study, BWi of a production bench in Sungun Copper Mine, located in East Azarbaijan province, Iran, was estimated. The rock’s geomechanical properties were measured using laboratory tests, including uniaxial compressive strength, Brazilian tensile strength, point load strength, and hardness. Then, BWi was estimated using the proposed formulas in the literature and the results of the rock’s geomechanical properties. The selected bench consists of three ore zones and two dyke domains. The laboratory tests revealed that the first ore zone has a slightly higher compressive strength than the other two zones, while the compressive strength of the waste rocks is larger than the ore domains. Using the proposed equations in the literature, the predicted values of the BWi for the samples in ore zones are in the range of 6.36 – 14.44 (kWh/t), and therefore this wide range must be considered when the short-term production schedule is planned. In addition, variations are observed in the samples within a specific zone and between the ore zones, demonstrating heterogeneity in the selected bench. Finally, wide-open results obtained by different equations show a necessity to perform a geometallurgical program specifically for the Sungun mine.

Oct 28, 2021

By Richard G. Almes

Since the failure of a major coal refuse disposal embankment and impoundment in the Buffalo Creek watershed near Man, West Virginia in early 1972, there have been extensive changes in the design and construction requirements for coal refuse disposal facilities located throughout the United States. The primary emphasis has been on improving the safety of these facilities, particularly for impoundments which are capable of storing millions of gallons of process water and storm runoff. The Mine Safety and Health Administration (MSHA) of the U.S. Department of Labor (formerly the Mining Enforcement and Safety Administration, U.S. Department of interior) has been the lead federal agency in promulgating regulations pertaining to coal waste disposal. In 1974 and 1975, studies were undertaken by our firm under contract to the Mining Enforcement and Safety Administration to prepare a comprehensive engineering and design manual to be used by operators and engineers in the planning and design of coal refuse disposal facilities with the intent ion of avoiding any more Buffalo Creek failures. The resultant 800-page document addresses major subjects such as safety, environmental controls, and cost. Specific topics include characterization of coal refuse, classification of disposal facilities, project planning, geotechnical investigations, testing and design requirements, hydraulic and hydrologic design, environmental factors, operations, and monitoring, instrumentation, and maintenance.

Jan 1, 1980

By P. R. Taylor

This investigation (Bowles, 1990) involves consideration of technology utilized by three separate fields of metallurgy and materials science: 1) The recovery of metals employing the use of solvent extraction, 2) The fabrication of materials using powder metallurgy, and 3) The use of composite materials in fabrication of engineering materials. The research considers each of the processes in order to realize the benefits of each. In light of the fact that materials have an intended use -it does seem plausible to simplify the process required between "mother earth" and final use. For instance, a primary copper producer that already employs a solvent extraction and electrowinning process could produce value added products directly. Part of the existing extractant flow could be diverted into a pressurized hydrogen stripping process in order to produce specialty composite powders. Innumerable methods have been employed for the recovery of metals; solvent extraction, the one considered in this study, was used due to the possibility of it providing a pure powdered metal. The use of solvent extraction in the recovery of metals has gained wide acceptance and its use proves beneficial in many applications (Ritchey and Ashbrook, 1984). Pressure hydrogen stripping of solvent extractants may provide the benefit of flowsheet simplification compared to conventional solvent extraction followed by electrowinning. It may also provide the benefit of direct production of high purity metal powder (Demopoulos and Distin, 1985).

Jan 1, 1992

By D. R. Nagaraj

Depression of copper sulfides followed by MoS2 flotation is the most commonly practiced technique for Cu-MO separation. Although numerous organic depressants have been developed in the past, a majority of the currently used copper depressants are inorganic compounds (ex. NaHS, Nokes reagent, etc.). A unique advantage of organic depressants over the inorganic compounds is the potential versatility for design of the organic molecule to suit many requirements. The present study was initiated to systematically investigate the structure- activity relationships for a large number of organic complexing agents in comparison with the commonly used inorganic depressants that are often inefficient and hazardous. The results obtained in this study are discussed in light of the useful correlation obtained between practical solution redox potential and depressant activity. Several requirements, such as the presence of an active -SH and hydrophilic -OH or -COOH in the organic molecule, are identified for a reagent to be a satisfactory depressant. Some preliminary results on the desorbability (or destruction) of collector coating on the sulfide surfaces in the non-xanthate collector systems are also discussed.

Jan 1, 1983

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By Steven E. Paulson

In situ mining is emerging as a potential alternative to conventional surf ace and underground mining techniques. A major factor in determining recoveries by in situ mining is the proportion of ore minerals that can be contacted and solubilized by the leach solutions. To provide basic information on the processes occurring during in situ leaching, particularly at the microscopic scale, the Bureau of Mines has developed a geologic characterization research program. This includes laboratory experiments using leaching apparatus that can accommodate whole core samples. Whole core experiments result in higher leach solution-ore mineral contact ratios than packed column experiments, and also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels in the rock. A nonreactive, reusable reaction cell has been designed and tested. The leaching apparatus can be used for constant-pressure or constant-flow experiments and allows for the control of flow rate, pressure, and temperature during the experiments, thus permitting studies on a wide variety of ore samples. Details of the experimental apparatus and design are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grande, AZ, area.

Jan 1, 1987

By F. G. Miller

Over the past 30 years, the coal industry has been continually striving to perfect methods for cleaning fine coal to acceptable ash and sulfur contents while maintaining maximum product yield. The flotation process has been part of this effort and its importance is expected to grow as new utilization technology demands finer and purer coal products. The work outlined in this paper is part of a larger effort aimed at development of new and improved flotation systems for removing sulfur and ash from as-mined coal as well as for producing super-clean coal for future markets. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of flotation.

Jan 1, 1986

By James A. Doolittle

In the underground type of mining operation, the finer portion of the waste material commonly is pumped as a hydraulic slurry to a tailings disposal pond. (1)* The tailings slurry is deposited via a pipe manifold system located around the perimeter of the pond. This method of deposition produces zoning because the coarser material tends to settle out immediately while the finer particles tend to remain in suspension and are deposited progressively nearer the center of the pond. The manifold system must be raised periodically as the pond fills with the tailings material. Over a period of time, this procedure will produce a zoned embankment known as a tailings dam. A typical pond and dam are shown in Figure 1. In plan view, the dimensions of tailings dams can be on the order of miles, with the height of the dam reaching 100 to 200 feet. Due to such factors as inadequate compaction, inherently low strength of the tailings material, and the possibility of high phreatic surface, many dams at some point become unstable, i.e., the factor of safety against a slope failure approaches 1.0. Remedial measures are required to improve the safety factor in order to prevent massive failure of the dam. In most cases, stability can be improved by effectively flattening the slope of the dam as shown in Figure 2, but this is not possible in every case. Occasionally, a tailings dam is constructed adjacent to a natural or legal boundary so that it is not possible to construct a conventional berm or to reduce the slope angle with earth moving equipment. Even a terracing process would require removal of the material and this may not be practical. In such a situation, an alternate scheme to improve stability must be found.

Jan 1, 1974

By Patrick Scott, Germán Schmeda, Morgan Mullins, Liam Knudsen, Bradley S. Van Gosen, Carma A. San Juan, Nicholas A. Karl, Jeffrey L. Mauk, Clayton Forbush

The objective of the US Geological Survey’s mineral deposit database project (USMIN) is to develop a comprehensive twentyfirst century geospatial database that is the authoritative source of the most important mines, mineral deposits, and mineral districts of the US. Since May 2017, the project has focused on critical minerals. Data for critical minerals that are produced as products are relatively robust, whereas data for critical minerals that may be recovered as byproducts are commonly of much poorer quality. Similarly, more is known about critical minerals that occur in conventional deposits than where those critical minerals occur in unconventional deposits. For example, rare earth elements occur principally in deposits hosted by alkaline igneous rocks, but there is potential for their production from phosphate rock mining, which is less documented. Lithium (Li) has been recovered from pegmatites and brines, but other Li-bearing deposit types have been delineated that may go into production. Cobalt may be produced as a byproduct or coproduct from a wide range ofmineral deposit types, whereas rheniumis a byproduct of copper ore. Significant opportunities for research exist that could help identify new sources of critical minerals, and may also help increase production and recovery from existing sources.

Feb 8, 2021

By Christos Roumpos, Philip‑Mark Spanidis, Francis Pavloudakis

Coal mining operations are large-scale, long-term frameworks of high complexity. Mining organizations accumulate, develop, and leverage knowledge from diverse scientific and technological fields as a result of these operations. Both practical experience and existing literature indicate that knowledge management (KM) methods within the mining industry primarily target solving immediate technical challenges and operational requirements. However, they are not commonly regarded as strategic tools to enhance the performance and competitiveness of mining companies. Empirical evidence from the Greek mining industry suggests that the management of available knowledge is intricate, less effective, and dysfunctional. This paper presents a methodology based on the principles of quantitative research (QNR), collaboratively conducted with a group of mining experts, to assess the KM landscape in the Greek mining industry. The methodology involves a structured data collection framework using questionnaires, subsequent statistical analysis, a discussion on critical methodological aspects, and an interpretation of results focusing on key aspects useful for planners and designers of KM systems in the mining industry. Finally, the paper concludes by summarizing the methodology’s outcomes and proposing further perspectives for research.

Mar 16, 2024

By Charles O. Frush

This paper presents a summary of the current employment practices with respect to recent graduates in Mining Engineering, as observed at the Colorado school of Mines. Because our experience is limited to our own group of students it prob¬ably does not correspond exactly to that experienced at other mining schools, but because the Colorado School of Mines graduates approximately 15 per cent of the men in this field our experience is probably representative. We have chosen to limit the information presented here to that pertaining to the period since July 1, 1960. This corresponds to the experience with the class of 1961 and to the experience of the class of 1962 up to the end of the first semester of the senior year. There were 36 mining engineering degrees given in 1961 In a class numbering 43 senior. We expect to give 30 first degrees in 1962 in a class numbering 44 seniors.

Jan 1, 1962

By E. H. Bentzen

The purpose of this paper is to explain the production of sand for glass manufacturing and the reasoning behind the sand specifications set by the glass industry. In order to discuss the production of glass sand, there is a need to understand what glass is and how it is made. Therefore this paper discusses glass, as well as sand beneficiation.

Jan 1, 1977

By Errol L. Montgomery

The region of metalic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 4,600 meters. Because surface water supplies are meager, new mines require unexploited sources of water. Prolific groundwater aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate groundwater quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum production water well capacities in excess of 170 liters per second.

Jan 1, 1982