Search Documents

By Shingo Morimoto, Toru Sasaki, Masato Shinji

"1. INTRODUCTIONTunnel face stability is one of the most important consideration in New Austrian Tunneling Method. In general, if all of the material properties of ground can be obtained through the field investigations, the tunnel face behavior can be predicted using numerical simulation prior to tunnel construction. However, estimating the safety of a tunnel face is difficult, especially in cases where the ground is very weak such as in an urban area.In this study, numerical analyses of tunnel excavation in very weak ground conditions, such as a low cohesion and low internal friction angle, were carried out. The relationship between the average shear strain distribution on the tunnel face and the overburden was analyzed. This relationship estimates the shear strain of the tunnel face relative to the critical shear strain obtained by the ground properties. The critical shear strain was defined as an allowable value for the maximum shear strain. We proposed the allowable overburden as tunnel face stability index (TFI) that satisfies the critical shear strain criterion of ground. Finally, a design chart of the allowable overburden for various cohesion values and friction angles of ground was created. This chart is useful in the preliminary tunnel design stage to judge the necessity of additional counter measures against normal tunnel support design.2. WEAK GROUND MODELING AND ANALYSIS PROCEDURE2.1 Setting material propertiesWith reference to a past study1), the material properties were adopted on the basis of material properties in the standard worst rock classification case called “DII”2) for standard support pattern of weak ground in Japan. The typical material properties for “DII” are listed in Table 1. In addition, Fig.1 shows the distribution of the representative weak ground according to cohesion and internal friction angle. When the internal friction angle is relatively high and the cohesion is weak, the ground is categorized as sandy ground. Furthermore, when the internal friction angle is low and the cohesion is strong, the ground is categorized as clayey ground."

Jan 1, 2016

By C. D. Litton

When methods to prevent the occurrence of fire in underground mines fail, the next line of defense is to rapidly and reliably detect the developing fire, so that subsequent evacuation and control procedures can be safely and successfully implemented. To provide this capability requires an understanding of the operational principles of different types of fire sensors, their merits as well as their limitations, and performance characteristics of the monitoring systems that control and process sensor data; an understanding of how fires develop and the different types of fires that can occur, along with their characteristics and the hazards they present; an understanding of the impact of the mine environment and routine mining activities, not only in terms of these effects on fire sensors but also in terms of the impact of mine ventilation and mine geometry on fire growth, fire characteristics and the detection process. All of these factors are components of the technology of fire detection, and when insufficient knowledge of any of these components exists, the ability to implement adequate mine fire detection systems is diminished. Within the last decade, significant advances have been made in fire detection technology applicable to underground mines. These advances include not only the development of improved sensors and better monitoring systems, but also an expanded understanding of how to deploy sensors, set sensor alert/alarm levels, account for ventilation effects, etc. In addition, there has been an increase in our knowledge of the types of fires that occur, the types of combustibles involved, characteristic times for fire growth and development, the levels of heat, smoke and gas that are produced and the hazards that result. It is the intent of this paper to provide not an overview of current mine fire detection technology and, also, to present data obtained for some smoke sensors that have potential for use in underground mines. The paper will also discuss the data, information and resources that are currently available and seek to identify those areas most in need of further research and development.

Jan 1, 2011

By Robert L. Llewellyn

The Wharton No. 2 Mine of Eastern Gas and Fuel Associates is located about 60 miles south of Charleston, West Virginia in Boone County. Daily production is 6,000 T.P.D. on a two-shift basis. The Hernshaw Seam is mined by conventional equipment with one continuous miner in areas where conditions are suitable. The plant is on Cow Creek .Branch of Pond Fork, which in turn flows into the Little Coal River at Madison, West Virginia. When the mine was opened in 1948, plans were developed to build a dual Baum jig plant complete with mechanical and thermal drying, and because full production would not be reached for several years, it was decided to install only one Baum jig setup although the complete structure was erected. This phase of the plant was placed into operation early in 1949, The rated capacity was about 300 T.P.H. of 5" x 0 raw feed to the jig. Being a drift mine, the 10-ton mine cars are dumped at the Headhouse, crushed to 8" in a double roll crusher, conveyed 780 feet downhill to the picking .house where the +5" slate is removed by pickers. All coal is crushed to 5" and 5" x 0 is conveyed 150 feet to the cleaning plant. Further describing the plant growth, the second jig setup was installed in 1954 to clean the increased production. During this operating period, exhaustive tests had ,been run on the plant bleed which was an overflow from the large sludge tank located inside the plant, When the second jig addition was undertaken, 5-14' diameter and 12-8" diameter cyclones with a 9-disc filter were installed for the solids recovery and water clarification system, However, the circuit was not closed and a bleed of part of the overflows from the 8" diameter cyclones was still necessary, To comply with the State Water Commission regulations on stream pollution abatement, four pumps in series were installed to discharge the waste water behind the refuse pile.

Jan 1, 1959

By John J. Sammarco

"The mining industry has made great strides in making mining safer and reducing the occurrence of mine disasters. Nevertheless, sometimes miners encounter smoke while trying to escape from a mine. Underground miners use different visual cues to help them escape from a smoke-filled environment. Foremost, miners look for primary and secondary escapeways that are typically indicated with reflective markers of various colors, with at least 11 colors available from manufacturers. Federal regulations require that escapeways be marked, but they do not specify the colors to be used. Thus, no standard color code exists and some colors can be more difficult to see in a smoke-filled mine.Researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) tackled this problem by taking a human-centered approach to provide miners with better visual information that would improve their ability to see escapeway markers in smoke, thus enhancing their ability to self-escape. What marker colors does your mine use?Does your mine use blue retro-reflective markers to indicate primary or secondary escapeways? Is your mine ready to purchase new or replacement retro-reflective markers? Color is important and blue had the poorest visibility as determined by OMSHR’s recent research investigating the visibility of markers in smoke. OMSHR researchers are not alone in their interest to improve a miner’s ability to escape - specifically when their efforts are hampered by smoke. For instance, there is a LinkedIn Mining Safety subgroup called "Standardized Color Code for Escape Ways and Returns in Underground Mines," and a recent National Academy of Sciences report recommended the development of humancentered technologies to enhance self-escape from underground mines. The mining industry has a common goal of helping improve miner safety, especially when it can be done by way of a simple and relatively low-cost solution of using escapeway colors that are more visible."

Jan 1, 2014

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By J. Kretschmann, K. Sakamornsnguan

"Sustainable development is an influential ethical concept in modern mining management. However, the concept is not culturally neutral because it is based on Christian, Western values. These values can be very different from traditional values in emerging mining countries like Thailand, where Buddhist values are dominant. When applying the concept of sustainable development, these differences should be taken into account. Different values imply different interpretations of ‘good mining’. They have a significant impact on how mining operations are evaluated, perceived, operated and managed. This paper attempts to integrate Buddhist principles with approaches of the sustainable development concept. When local values are appreciated and maintained, mining companies and their external stakeholders can identify objectives and approaches that match with their own values and contexts. Practices based on this integrated ethic can help to promote sustainable mining and to minimize communication risks for enterprises in mining countries like Thailand. INTRODUCTION The objective of this paper is to integrate Buddhist principles to the application of sustainable development concept to mining activities. The structure of this paper is divided into four parts. An introduction provides basic information about Thailand, its mining industry and the role of Buddhism on the past development. The second part compares the differences between the sustainable mining framework and the implications of Buddhist principles on mining. In the third part, the core Buddhist teachings are integrated into the sustainable mining framework. This is followed by conclusions in the last part. THAILAND, BUDDHISM, AND MINING Thailand is a constitutional monarchy state in Southeastern Asia with a population size of around 65 million [1]. Its GDP in 2013 was 391 billion USD [2], predominantly deriving from manufacturing (38%), trade, transport and communication (24%), agriculture (8%) and mining and construction (4%). Still the largest part of the Thai workforce (39%) is working in the agricultural sector. The remaining part of the workforce is equally distributed across services, manufacturing, and mining and construction sectors. [3]"

Jan 1, 2015

By Roy A. Grancher

HAPPY BIRTHDAY Not only is 1971 the Centennial Year of the AIME, but it also marks the One Hundredth Anniversary of the United States Portland Cement Industry. On September 26th in 1871 David O. Saylor of Allentown, Pennsylvania, received his patent Numbered 119,413 for the manufacture of portland cement. "Cement" had been used in the United States before that. This was, however, natural cement - a direct product of rocks as found in nature, usually burned at low temperatures in open kilns. During the early 1800s this natural cement played an important role in such projects as the building of the Erie Canal. It was only after the Civil War that small amounts of high priced portland cement was imported from Europe. The successful use of this material in construction led to Saylor's experiments and subsequent patent for the manufacture of a scientifically controlled product in this country. These one hundred years have witnessed four major "ages" of cement . . . three of them occurring in the last quarter century since World War Two. The first age was the "Age of Development", a seventy-year period which saw the growth of cement and its concrete end uses as major construction materials. Next followed a period called the "Age of Demand" when, after the war, cement became in short supply relative to large building requirements. In effect a cement shortage existed. The decade of the Sixties proved to be the "Age of Reaction", with its courses of action coming in response to the problems that arose when the industry's expansion programs provided too much capacity. Today cement, and the concrete industries, find themselves entering the "Age of Reason". Overcapacity, low price, rising costs, and poor returns are several of the reasons behind that name, As these industries face the construction challenge of the Seventies, and beyond, the application of basic management principles (otherwise known

Jan 1, 1971

"A commercially available through-the-earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electricfield (E-field) sensing to send text-based communications through two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivities. IntroductionWireless, through-the-earth (TTE) communication technology is designed to achieve point-to-point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. Using this approach, communications are established without the need for intermediary communications infrastructure. As a result, TTE systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers, 1924; Pittman, Church and McLendon, 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon, 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker, 2006; Wadley, 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer, 1973; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Jakosky and Zellers, 1924; Large, Ball and Farstad, 1973). Although commercially developed TTE systems have demonstrated the ability to communicate in a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker, 2006; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Ilsley, Freeman and Zellers, 1928; Jakosky and Zellers, 1924; Yenchek et al., 2012)."

Sep 1, 2016

By A. Bhagwat, S. Tadolini

"Steel members of the ground support systems in underground mines are routinely exposed to corrosive environment that may range from acidic to alkaline. Corrosion of steel bolts leads to metal loss and thereby, reduction in strength and useful life. Protective coatings are commonly applied to the steel bolts to combat corrosion. However, coatings are expensive and often cumbersome in practical applications. Instead, Minova has developed an innovative technology based on sacrificial anodes. The anodes were designed from non-ferritic alloys that are inferior to steel on the Galvanic Series. This paper will present data from field testing to show significant benefit of the technology. Potential applications in current products will be discussed. INTRODUCTION Corrosion is a physical alteration of a steel material from electrochemical reaction with its environment that often results in reduction of the mechanical and physical properties of that material. Mine roof bolts, the subject of this investigation, are particularly susceptible to corrosion as they can be exposed in their working environment to ground water and air with high humidity. As other researchers have determined, corrosion increases markedly in sulfide ore bodies due to acid runoff. There are several types of corrosion that a rock bolt is likely to undergo when used for ground reinforcement in underground mines (Aziz et al., 2013). Of all the types of corrosion, pitting is particularly dangerous as it can remove capacity for the bolt to deform with subsequent strata movements. Sudden failure of a bolt is likely to occur when severe pitting corrosion is experienced. The type and nature of corrosion depend on the nature of the ground condition and bolt encapsulation. Generally, the type of corrosion and severity of the corrosion varies along the axis of bolt. Almost all of the mine roof bolts used in mines, with the exception of fiber reinforced polymers, are made from steel. The corrosion of iron is an electrochemical phenomenon with the overall equation:"

Jan 1, 2018

By R. Fernando

"The National Institute for Occupational Safety and Health (NIOSH) National Personal Protective Technology Laboratory (NPPTL) is leading an effort to develop the next generation of self-escape breathing apparatus for egress from confined spaces in emergency scenarios. A backpack style closed-circuit mine escape respirator design was one configuration explored as part of the research imperative directed by the 2006 MINER Act. Stakeholder feedback from MSHA and at the NIOSH Breathing Air Supply Partnership Meeting indicated a smaller belt worn unit that does not sacrifice performance is desirable. This paper outlines some further technology advancements that may be investigated toward developing such a small-sized respirator. Technologies being considered are novel chemicals for improved carbon dioxide (CO2) absorption and oxygen (O2) production, eliminating a dedicated CO2 scrubber by incorporating its function in the spaces of the respirator’s breathing loop and storing O2 in a liquid form with long standby capabilities. When these technologies are applied to a future design, there is the possibility of having an escape respirator that can be belt worn and capable of being certified to 42 Code of Federal Regulations (CFR) Part 84 standards, including sub-part O for escape purposes including mine escape. BACKGROUND NIOSH NPPTL has a Research and Development effort to provide mine workers with state-of-the-art breathing air technologies to comprehensively support initial and continued self-escape, refuge alternatives, and rescue needs, resulting from mine emergencies. As part of this R&D effort, NIOSH invested in the development of a next-generation closed-circuit mine escape respirator (CCMER) which would be compliant with NIOSH’s respirator standard requirements, 42 Code of Federal Regulations Part 84, including sub-part O. The design features of the CCMER also address the MINER Act’s requirements for transitioning between devices without the need for doffing the initially donned device. It would also allow for improved protection when using voice communications with a donned device ."

Jan 1, 2018

By Daniel Lakovic

"Mining operations can create a negative environmental impact, especially when considering the tailings that are produced through the processing of ores. Tailings are finely grained residues that form sludges. The tailings are deposited into giant basins, or sludge ponds, where they create a burden on the environmentby limiting the use of processed water.Tailings are one of the most important environmental liabilities for mining operations because of their large proportion in relation to the ore mined — generally 90 to 98 percent. To get to the valuable minerals, mining companies must move large amounts of rock. The rock is ground and then treated, usually with the addition of chemical solutions and large amounts of water. The lower the concentration of the valuable resources, the greater the proportion of accumulated excavated material sludge.Sustainable tailings management requires responsible handling, making it one of the mining industry’s greatest challenges. The proper technology should include consistent control of the environmental risks and impacts, as well as a proper relationship with the communities that surround the mining operations.The tailings, which can remain partly contaminated with chemicals, are pumped into the large sludge basins, which are secured by earthworks. During the mining operations, the basins must be stable enough to withstand the pressure of the stored excavated material. The storage option is still used, but it has failed on occasion. And when it does, it increases the risks to the environment and binds the unused process water. The more complex the availability of fresh water required for industrial use and for human consumption and their economic activities — for example, farming and agriculture — the more complex the conflicts that have the potential to shut down mining operations. With modern separation technology solutions, it’s possible to process the sludge and recover the processed water. However, the responsible use of the water is critical. Therefore, mining companies must rely on technologies that allow for proper reclamation of the water, whether re-using in their own processes or treating it to return it to the environment."

Dec 1, 2018

By A. P. Mehta

The role of microorganisms in the leaching of metal sulfides is well established (Torma, 1977; Murr, 1980). However, this established knowledge applies mostly to chemolithotropic microorganisms such as Thiobacillus ferrooxidans which function optimally in leaching catalysis between 25-35° C, and in a pH range of 2-2.5. Although leaching with thermophilic microorganisms capable of extending the range of catalytic viability beyond 35° C is also documented, there are few if any attempts to optimize or extend sulfide concentrate leaching with thermophilic microorganisms. When mixed metal sulfides or other materials having different rest potentials (referenced to the standard hydrogen electrode, SHE, in the electromotive series) make contact in a conducting, aqueous medium, the contacting members will act as an electrochemical cell, with the member having the higher rest potential assuming the role of an electrical cathode. In leaching reactions involving such galvanic couples, the cathode becomes passivated, while the anodic member reacts vigorously due to the electro- chemical reaction which occurs (Hiskey and Wads- worth, 1975). Serry, eta1 (1978) observed that when chalcopyrite and pyrite were in intimate contact in natural ores, the chalcopyrite reacted vigorously by galvanic conversion as a result of the higher rest potential (~ 0.63 V) as compared to the chalcopyrite (~ 0.53 V). In addition, it was postulated that because of the elemental sulfur which can form on the anodic chalcopyrite in this galvanic conversion process, reactions in acid-bacterial medium would be expected to have accelerated copper extraction because of the conversion of any sulfur product layer on the chalcopyrite anode to sulfuric acid according to the following general reactions: [MS?M2+ + S° + 2e- (1) and 2S° + 302 + 2H20 bacteria?-2H2SO 4 (2)] where M in reaction (1) designates the metal (or metals in the specific case of chalcopyrite) to be released to solution by galvanic conversion.

Jan 1, 1982

By Joseph F. Shirley

Introduction Inorganic depressants are chemicals added to the froth flotation process to maintain or produce hydrophylic surfaces on one or more minerals so they will remain in the pulp rather than attach to the air bubbles. Whether a depressant will be effective in depressing a given mineral depends on how it is used and the environment in which it is used. Some depressants must be added and conditioned into the pulp before the collector is added. Other depressants can be added in the presence of previously added collectors and effectively depress the desired minerals. Often the concentration of depressant relative to the collector concentration is critical to making an economic separation. It should be noted that some depressants will only work when specific collectors have been used. Some reagents such as sulfuric acid and hydrogen peroxide essentially act as depressants by altering the previously added collectors so that they are no longer effective. Some depressants such as sodium ferrocyanide are only effective in a very limited pH range and an essentially collector free environment. Major Depressants CaO Milk of Lime is by far the most used depressant both in tonnage and dollar value. Although it is most commonly listed as a pH modifier, it is also an important depressant for pyrite in copper and copper molybdenite flotation plants. Although a simple pH adjustment will often depress pyrite, there are times when grinding with fresh milk of lime is required to obtain optimum depression. Lime is also a molybdenite and gold depressant. NaSH Sodium hydrosulfide is by far the most commonly used reagent to depress copper and iron sulfide minerals in by-product molybdenite flotation plants. NaSH also depresses gold, silver sulfides and silver chloride. ZnSO4 Zinc sulfate is commonly used to depress sphalerite in lead-zinc and copper-lead- zinc flotation plants. It has also been used to effectively depress talc in by-product molybdenite circuits at a pH of 6.5.

Jan 1, 1986

By G. E. Bandelis

In this paper, solid bed erosion processes and the mechanisms involved when a two-phase liquid-solid mixture flows over a bed of solids in a horizontal annulus are analyzed. There are few such studies available with some authors arguing that the flow rate for erosion is always less than the flow rate for the suspension of solid particles thus necessitating further study and analysis of such phenomena. Tests were run to determine the mechanism of erosion and the erosion velocities of the solid bed formed in a concentric annulus for three flu-ids, water, a low concentration water solution of Carboxyl-methyl-cellulose (CMC), which behaved as a Newtonian fluid and a higher concentration CMC water solution which behaved as a power law fluid. Glass spheres of 2 mm nominal diameter were used as solids. The flow rate at which erosion occurred together with the mechanism of bed erosion were determined visually, while the whole process was video recorded. Our tests indicated different erosion mechanisms and different erosion velocities for the three tested liquids, with the liquid viscosity playing a major role. The first mechanism, observed for water flow, gives erosion from the front of the bed while the second mechanism, observed for the flow of the two viscous fluids, gives erosion from the top of the bed. The role of each of the parameters to erosion is investigated, whether it is turbulent flow with the turbulent fluctuations being more capable to remove the solids from the formed bed or whether it is liquid viscosity, which results in the hydrodynamic shearing force. The results demonstrate that liquid viscosity plays a role in the erosion mechanism and yields different erosion velocities of the solid bed hence, it should be taken into account when modeling flow pattern transitions for solid-liquid flows. Prior studies have not identified this and it could be the reason of the disagreement between theoretical models and experimental and field data.

Jan 1, 2006

By C. J. Pritchard, R. E. Gundersen

I commend the authors on examining an interesting method of shaft lining and attempting to improve safety in a dangerous environment by remotely installing the shaft lining. It is important, though, to not trade off shaft lining safety for long-term mine safety by lining an intake shaft with combustible material. In many operations, the mine utilities are installed next to the lining of the intake shaft, supplying a possible ignition source if damaged or overloaded. Although the polyurethane studied in the paper is of relatively high density, no mention is made of the flame retardency of the samples. When exposed to heat, small amounts of polyurethane will melt and bum but are extinguished when the heat source is removed. If large surface areas of combustible polyurethane - a tunnel or mine shaft- are exposed to ignition heat sources that are not removed or extinguished early, an uncontrollable, fuel rich fire may result with high carbon monoxide levels, low oxygen concentrations, and greatly increased burning rates that can have devastating effects on the ventilation system and miners' safety. Although these heavy polyurethanes lend themselves to a "pouring" application around the annulus of the shaft liners and is a continuous process, past experience with atomizing and frothing polyurethane spray systems indicates a high degree of maintenance and operator attention to the nozzle1 delivery system. This may require more miner's time to be spent in the shaft maintaining the foam system, negating some of the safety advantages of the system. If polyurethane foams are to be used in mines, they must be of the highest quality available in terms of flame spread, heat emitted while curing, and contaminants emitted while curing and spraying. In addition, employees must be given adequate training and be thoroughly informed in all aspects of polyurethane foam safety procedures. As witnessed by our fellow miners in South Africa, we can accept no less.

Jan 1, 1991

By Charlie Sons

Pit and underground mine operators typically use a lot of big equipment tires. Just as typically, they spend a lot of money they shouldn't on these tires. That's because tire use and maintenance are not given enough attention. That often occurs because mine management and personnel do not know the basic facts of tire use and care. If a piece of large equipment is damaged or ruined, a good explanation better he forthcoming. A ruined tire is often just a shoulder shrug. But that sort of fatalistic acceptance can cost tens or hundreds of thousands of dollars a year extra for big equipment tires. That does not have to be. There are some basic tire considerations that, if followed, will extend tire life and lower tire costs. Most companies have the inevitable conflict between the production department, which resists any restrictions that may reduce productivity, and the maintenance department. Production success is based on meeting a schedule of yards moved, while maintenance success is based on availability and equipment cost. When production falls behind schedule and equipment speeds are increased, maintenance may soon find its tire costs rapidly increasing, unless everyone understands the tires' vulnerability to damage. Unless the production department understands the problem, or restraint is applied by top management, costs may become exorbitant. At one job site, tire costs alone exceeded $250,000, to move 55 dam3 (72 000 yd3) of dirt on an 11-km cycle. The operation temporarily caught up with its schedule, but tire costs and attendant downtime soon made this a not-for-profit exercise. Because an operator must always attempt to move payload at the lowest cost, there are cases when higher than normal tire costs must be accepted. For example, in pioneering work with tandem engine scrapers, steep grades shorten tire life to less than normal. But the steep grades make shorter haul cycles possible, yielding more trips per hour than alternative earth-moving methods.

Jan 1, 1982

By D. O. Miller

The effective staffing of personnel in a new concentrator facility is a key factor in the success of the operation. By selectively recruiting quality individuals, a company is in a strong position to build a positive work ethic which will become an integral part of it's culture. And culture, which is a set of standards that all employees work to uphold, is that intangible as- set that often determines whether or not a company will survive during difficult economic times. Recruiting and placement of personnel in a concentrator facility requires an emphasis on planning. Management must carefully analyze the following elements when designing a hiring plan: 1. Number of positions 2. Hiring schedule (timetable) 3. Critical positions 4. Lead-time for trainee posit ions 5. Characteristics of the ideal workforce This presentation will focus on a proven system that is efficient (and yet simple) for achieving a new concentrator facility's manpower requirements. IDENTIFYING THE STAFFING NEEDS As previously stated, the key to staffing is planning. Management will find that a basic manpower chart will provide the hiring schedule to meet deadlines. In fact, this system begins with a manpower chart (Figure 1). The chart basically works in reverse of the hiring requirements: the last scheduled hire is the first job on the list. This approach ensures that the company will not find itself compressed against the facility start-up date. A cardinal rule in recruiting a workforce is to allow sufficient time to orient and train employees to the procedures and culture of the system. Problems in selection of personnel begin when the hiring program is short-circuited for timing reasons. The quality of employee selected invariably suffers accordingly. The second section is the key to the success of the manpower program. This is the latest date by which a formal recruiting effort must begin in order for the hire date to be met. Leadtimes are usually as follows: 1. 90 days for company transfer positions 2. 60 days for experienced new hire positions 3. 30 days for trainee positions

Jan 1, 1986

By N. Ohmura, H. Saiki, T. Nagaoka

A microbiological flotation system that facilitates the removal of pyritic sulfurfrom coal is reported. The chemoautotrophic bacterium Thiobacillus ferrooxidans is utilized as a pyrite-selective biological surfactant that augments the flotation-mediated rejection of pyritic sulfur. The bacteria were produced by continuous cultivation in 50-L tanks, where it was possible to produce 3.8 x 1012 cells/day when the dilution rate was optimal and the pH was 1.6, a condition that prevented ferric precipitation. Prior to flotation, the bacteria were mixed with coal, which allowed cells to selectively adhere to the pyrite. The adherence of bacteria made the pyrite surfaces more hydrophilic, which facilitated separation by increasing the tendency of pyrite to sink, while the hydrophobic coal floated. When a synthetic coal/pyrite mixture (10.1 % sulfur) was subjected to microbial flotation, the level of sulfur rejection was stable during the entire period of operation (i.e., one hour). In the absence of bacteria, flotation reduced the sulfur content of a coal/pyrite mixture to within the range of 6.7% to 7.4%, with the combustible recoveries ranging from 93.9% to 99.0%. In the presence of bacteria, the sulfur content of cleaned coal was in the range of 1.3% to 1.4%, with the combustible recoveries ranging from 80.8% to 86.3%. Bacterial activity accounted for 57% of the total sulfur rejected through flotation. The desulfurization capacity of the system was further confirmed by testing it with run-of-mine coal. The pyritic sulfur content was reduced from 2.9% in the feed coal to around 1.2% in the froth product, while 80% of the combustible recovery was retained. Microbial flotation removed 60% of the pyritic sulfur from the feed. These findings demonstrated that micro¬bial flotation could be utilized for the removal of pyritic sulfur from coal in a semicontinuous system.

Jan 1, 2000

By Thomas E. Garnar

Zirconium and hafnium are the twin elements of the periodic table because they are always found together. They resemble each other so closely that hafnium was not discovered until 135 years after the discovery of zirconium. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium's chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and von Hevesy detected it using X-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO,) and less commonly as baddeleyite (ZrO,). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. During World War I, it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s, when Zircon Rutile, Ltd., began mining at Byron Bay on the east coast of Australia, that zircon was first used as foundry sand. Later in the 1940s, NL Industries and Humphreys Gold Corp. began production of zircon sands from fossil beaches in northeast Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties and as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by the Republic of South Africa and the United States. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, the former USSR, China, Thailand, and Brazil. The location of world zircon mines, baddeleyite mines, and undeveloped zircon ores are shown in [Fig. 1]. World production of zirconium mineral concentrates is shown in [Table 1].

Jan 1, 1994

By Wolfgang Pietsch

Roller presses were first invented in the middle of the 19th century, for the economical size enlargement of coal fines as fuels. Coal briquettes became quickly accepted for industrial and domestic use giving rise to a large and sucessful industry, particularly in Europe, Japan, and North America. When, towards the middle of the 20th century, coal was more and more replaced by other energy sources, such as electricity, gas, and oil, roller press manufacturers searched for alternate applications of this equipment. In addition to contemporary coal briquetting, in fields such as smokeless fuel and form-coke, it was found that redesigned and modernized roller presses, which are now capable of exerting high forces, are versatile machines for many tasks in mineral processing. Today they are used for: - the "classic" pressure agglomeration and - the "new" high pressure comminution. In pressure agglomeration, the characteristics of fine minerals are improved by forming briquettes or granulated products from compacts. During size enlargement with roller presses briquettes are directly obtained while granular materials are produced by crushing and sizing of compacted sheets. The processes are carried-out essentially dry and often do not require binders other than those inherently contained in the feed and "activated" by the high forces and/or elevated feed temperatures (e.g. hot briquetting). Therefore, no foreign materials (impurities) are added. Another advantage of the technology is, that wide particle size distributions are acceptable or desirable as feed materials, including millimeter or even centimeter sized particles. Plastic particles deform and brittle materials are crushed during pressure agglomeration. A relatively new application of roller presses in mineral processing is the utilization of the crushing effect when brittle materials pass the nip area between the rollers. It was found that this crushing mechanism is very efficient thus saving energy, particularly in grinding circuits handling large capacities. The paper introduces the fundamentals of the process and describes the design as well as applications of modern roller presses in mineral processing.

Jan 1, 1995