Search Documents

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

By W. A. Wilkinson

In creating a surface mine design, a complicated series of events may be required to meet both mining and environmental objectives. Envisioning the mine at every step of the operation can greatly assist the engineer to identify design and operational problems that might otherwise go undetected until the field operations reach the problem. Providing operations a visual progression of the mine ensures that critical designs generated by the engineer are understood and effectively communicated to operations. Providing the plan as electronic data to the surveyors and/or on-board GPS systems can ensure successful implementation of the design. This paper discusses using computer technology to generate a virtual mine plan and strategies to consider when communicating a virtual mine plan through electronic and paper formats.

Jan 1, 2002

Although out of the ordinary, MINING ENGINEERING is pleased to present a few photographs that typify Western US mining activity during WWII. The photographs, taken by R.G. Zellers at Colorado mining operations between 1942 and 1946, were primarily intended for equipment manufacturers. The pictures capture scenes of hardworking miners during a time when output was essential to fuel a wartime effort. In addition to providing a rare opportunity to step back 40 years and view the equipment and activity common at the time, Zellers' skill with photo composition and his ability to obtain clarity in dimly lit underground operations gives viewers an acute awareness of the dampness and dirt of the mines, and a sense for the miners' limited working space.

Jan 6, 1983

Recent advances in GPS, machine guidance technology and telemetry allow an unprecedented level of control of surface mining operations. GPS technology can now locate the bucket of a shovel or the blade of a dozer within 50mm (2 inches).Some of the outcomes possible are: precise selective mining – even when the ore is visually indistinguishable from waste: tracking grade and tonnage of every ore parcel through the mine: real time productivity monitoring: detailed post accident safety analysis: tracking the movements of every piece of equipment. This paper will consider the contribution that GPS based machine control systems can make to ensuring that surface mining projects deliver the outcomes promised in the feasibility studies. Case studies of installations are presented.

Jan 1, 2004

By M. C. Azar, W. B. Mason, G. L. Anderson

Eminent domain overview Eminent domain is the power of the Government or a municipality to take property for public use without the consent or acceptance of the owner. Typically, the agency taking the prop¬erty will make an offer, hoping the owner will immediately accept and allow work to begin. If a mutual resolution regard¬ing its value cannot be reached, how¬ever, the municipality will institute a condemnation action in court seeking possion of the property. This is when the problems begin. The power of the Government to take the subject property is limited by Federal and state constitu¬tional requirements to pay "just com¬pensation" for the property. The exact nature of an owner's prop¬erty has been the subject of much debate and discussion. It is generally under¬stood, though, that property is consid¬ered to be "every kind of right or inter¬est, capable of being enjoyed and recog¬nized as such, upon which it is practi¬cable to place a money value" (US vs. 53 114 Acres of Land). A taking, for condemnation purposes, is considered to occur whenever there is a substantial interference with the free use and enjoyment of the property. Rarely is the necessity for the taking ever challenged and more rarely is the taking ever successfully challenged. When a taking occurs, it is not only the fee owner who is entitled to compen¬sation. Every person holding an interest in the subject property will be recog¬nized. Thus, all persons who at the time of taking have a compensable interest in the property will be made parties to the case (Swanson vs. US). Minerals, like all other interests in land, are recognized as property rights, giving the owner the power to dispose of them as he or she sees fit. Thus, the only remaining considera¬tion is only "just compensation." Ex¬actly what "just compensation" is has been difficult to define. Generally, it is that amount of money that will "put the person in as good a position as the per¬son would have been in had the taking not occurred." The owner must not be forced to sacrifice or suffer by receiving less than full and fair value for the prop¬erty. Every element that effects the value of the land and that would influence a purchaser must be evaluated. Courts have employed a variety of techniques to determine just compensa¬tion but have generally relied on market value as the standard for measuring compensation to the owner. The deter¬mination of market value is based on sales, income, costs, and use. These factors have been employed in various ways but can be summed up as: -The highest estimated monetary price the property will bring if exposed for sale in the open market with a reason¬able amount of time allowed to find a purchaser who is buying with knowl¬edge of all the uses and purposes to which it is adapted and for which it is capable of being used. • The amount the property would bring if it were offered for sale by one who desired, but was not obliged, to sell, and was bought by one who was willing, but not obliged to buy. • What the property would bring in the hands of a prudent seller, at liberty to fix the time and conditions of sale. • What the property would sell for in negotiations resulting in sale between an owner willing, but not obliged to sell, and a buyer willing, but not obliged to buy. • What the property would be rea¬sonably worth on the market for a cash price, allowing a reasonable time to affect a sale. (Michigan Standard Jury Instructions). Special consideration regarding mar¬ket value is given when the taking is only partial, rather than complete. An example of this partial taking is when a state highway cuts across the northern half of a parcel of property, leaving the rest behind for the owner. A variety of problems can be immediately seen. In a partial taking, the owner is permitted to recover not only for the property taken, but also for any loss in the value of the remaining property. The measure of compensation for partial taking purposes is generally the difference between the market value of the entire parcel before the taking, and the market value of what is left of the parcel after the taking (Michigan Stan¬dard Jury Instructions). Determining the partial taking value for mineral bear¬ing lands is the difficult issue.

Jan 1, 1989

By A. J. Thompson

The Metropolitan Transportation Authority (MTA) East Side Access project (ESA) will, when it is complete, provide a new link to the east side of Manhattan from Long Island, NY that, linked with the Second Ave. Subway currently under construction, will assist in relieving overcrowding at Penn Station as well as the Lexington Ave. subway. ESA will bring Long Island Railroad (LIRR) directly from Long Island into a new station located 37 m (120 ft) beneath the existing Grand Central Terminal (GCT) located in the heart of Manhattan. It will connect the LIRR?s mainline tracks in Queens, via the existing 63rd Street Tunnel under the East River, to a new terminal constructed within, and beneath, the historic Grand Central Terminal.

Jan 1, 2012

By H. J. Sutherland

This paper reviews the results of the subsidence research prop ram at Sandia National Laboratories. The manuscript highlights the following: the application of empirical methods (profile functions) to the subsidence above longwall panels in the U.S.; the use of the "rubble model" to describe the behavior of broken strata as it distends when it falls to the Mine floor (or top of the rubble pile) and then is subsequently compacted as it is loaded by overlying elements of strata; and, the application of physical modeling techniques (centrifuge simulations) and numerical techniques to study the failure mechanisms in highly structured stratigraphy. The capabilities of the latter two are illustrated ')y comparing their predictions to the results of a field case that has complicated stratigraphy.

Jan 1, 1982

By Frank Florez

INTRODUCTION The Magma mine, located at Superior, AZ, some 100 km (60 miles) east of Phoenix, was discovered in 1875, and was originally mined for silver. The property was acquired by W. B. Thompson who formed the Magma Copper Co. in 1910. Prior to 1965, square-set mining and cut-and-fill methods were used to mine steeply dipping veins at Magma. Ore was moved to the chute by gravity in the square-set stopes and by slusher in the cut-and-fill stopes. The stopes were gobbed with waste from the surface and development headings in the mine. The original square-set method of mining was modi¬fied in order to extract replacement ore bodies in limestones that dipped at 0.52 rad (30°) and varied in thick¬ness from 4.6 to 38 m (15 to 125 ft). Mining of these ore bodies was done by starting at the upper lateral ex¬tremities and retreating to the access openings. The timber square sets and cribbing were used as temporary support, the ground being allowed to cave as the mining retreated. It was found, however, that mining in such a manner was very inefficient; safety hazards increased be¬cause of the blocky and fractured characteristics of the ore and the weakness of the hanging wall. GENERAL DESCRIPTION The undercut-and-fill method of mining is now the primary stoping method used at Magma, and no pillars are left for later extraction. Four ore bodies are pres¬ently being mined. These ore bodies (see Fig. 1) dip conformably at 0.52 rad (30°) to the east with the host limestone and shale sediments, their average strike length is about 122 m (400 ft), and their thickness varies from 9 to 38 m (30 to 125 ft). The ore bodies are separated by varying thicknesses of barren rock. Three of them come together at various elevations primarily in the area of the main feeder fault, but there is an apparent horizontal displacement of about 23 m (75 ft) on the main feeder fault which complicates stope layout. The method as originally applied has been modified in order to mine more efficiently ore bodies that are 9 m (30 ft) or more in thickness. The modification was made to mine all the ore at a given elevation before dropping down for the cut below. The advantage of this is that mining is done on a horizontal plane and there¬fore muck removal can be mechanized. Also multiple faces are made available, thereby improving overall min¬ing efficiency. Another major change made was to carry a 6.7-m (22-ft) face when mining the top sill and a 6.4-m (21-ft) face when mining under fill rather than the former standard 3.35-m (11-ft) high face. This change lengthens the mining cycle and cuts mat prepa¬ration costs in half. Stopes are laid out (see Fig. 2) so that maximum mining panels are available and yet one stope crew will not tie up too much of the ore reserve. One stope might consist of as many as 20 panels, and these panels are divided evenly on opposite sides of the extraction cross¬cut. The stope layout is planned so that the maximum tramming distance to the orepass will not exceed 30.5 m (100 ft) on the crosscut and 38 m (125 ft) in the panel. Stope panel distances are sometimes exceeded when min¬ing to the extremity of the ore body. Tramming distance limits are determined by the efficiency of the com

Jan 1, 1982

By J. W. Carson

Introduction Many bulk solids such as coal, limestone, and fine moist ores often flow unpredictably out of bins, hoppers, and boreholes. Vast amounts of time and money are spent-with or without success-on flow promoting devices. In addition, many solids segregate in storage, feed erratically, flood, arch, rathole, and stick to bin walls reducing the live capacity. This article discusses bulk solids flow properties and provides guidelines for designing storage bins, hoppers, and feeders to provide reliable flow. Bulk Solids A bulk solid is a granular material consisting of discrete solid particles-submicron to several inches in size-that is handled in bulk form (for example, in a bin or silo). The gas filling the voids is generally insufficient to fluidize the material and the liquid (usually water) content is assumed to be less than saturation. Types of Flow Problems To design an efficient storage system, an engineer must be aware of problems that can arise during storage and flow of bulk solids: • No flow. A stable arch or pipe (rathole) develops within the solid, stopping flow. • Erratic flow. Momentary arches form within the solid, (ratholes), partly or completely empty out, and then collapse. • Flushing. Powders become fluidized, aerate, and flush uncontrollably through the bin outlet. • Lack of design capacity. A large part of the stored material remains stable around a rathole. Manual prodding, severe vibration, and even explosives may be used to restore flow. • Segregation. Smaller particles tend to sift through the voids between larger particles causing accumulations of fines and coarse in various areas of the bin. • Product degradation. Some materials spoil, cake, or oxidize if they remain in a bin too long. This is usually caused by a first-in-last-out flow sequence. • Level control. Measuring the volume of material left in a bin is difficult if a rathole develops. In one portion of the bin the level control device may indicate the bin is full; in another portion it may indicate it is empty. Eliminating Flow Problems All flow problems can be minimized or prevented by suitable design of the bin/feeder unit. This involves knowing the flow properties of the solid, then choosing the appropriate type of bin and feeder to establish the desired flow pattern. There are three types of flow patterns that may occur in a bin: funnel flow, mass flow, and expanded flow. Funnel flow occurs when some of the material in the bin is stationary while the rest is in motion. Funnel flow bins, shown in Fig. 1, are characterized by: • Low head room. A flat bottom or shallow hopper bin has large storage capacity with minimum height. Unfortunately, all this storage capacity may not be usable ("live"). • First-in-last-out flow sequence. The first material put into a funnel flow bin is the last material withdrawn because the flowing material is concentrated in the region directly above the outlet. • Ratholes. Because of the flow channel that forms, a stable rathole develops if the material has sufficient cohesive strength. • Erratic flow. Once a rathole becomes partially or completely empty, it may collapse creating a stable arch and erratic flow. • Flushing. Collapsing ratholes cause flushing and flooding of fine material. • Segregation. If a bulk solid has a tendency to segregate, this tendency will be accentuated as the material is discharged from a funnel flow bin. Funnel flow bins are suitable for coarse, free flowing, nondegrading solids, when segregation is not important. Mass flow occurs when all the material in a bin is in motion whenever any is withdrawn. Char-

Jan 3, 1983

By V. Miller

C. Hertzler The difference of means of milling characteristics by rock and ore type is tested in a statistical manner in the paper. The null hypothesis being tested is that the sample means of two different populations are equal. It is assumed that the null hypothesis is true when performing the test. Because of this, acceptance of this hypothesis leads to the conclusion that the sample means of the two different populations are equal (or there is no significant difference between the sample means), not that the samples come from the same population, as the author asserts. Rejection of the null hypothesis leads to the conclusion that the sample means of the two different populations are not equal. A P value for this test is reported in Table 2 and is incorrectly identified as the probability that the two samples came from different populations. Actually, what was recorded was 100(1 - p) where p is the usual p-value. The usual p-value measures, on a scale of zero to one, the extent to which the data agree with the null hypothesis. It is the probability of observing a value of the test statistic (Z score) that is at least as contradictory to the null hypothesis as the one computed from the sample data (McClave and Dietrich II, 1982). The author makes no mention of the fact that were these tests to be conducted together, the chances of determining that the null hypothesis is not true when it is really true are increased considerably (Snedecor and Cochran, 1980). This is a multiple comparisons problem and should be dealt with accordingly. The usual methods involve adjusting the level of the individual tests. Table 2 reports an incorrect 100(1 - p) value in the comparison of concentrate grades for other rock types with .30 to .69 % Cu vs other rock types with .70 + % Cu; 86 % should be 98.6 %. Although the article can be criticized for poor data presentation and discussion of that data, the point the author makes regarding the use of these statistics in the ore reserve estimation process is well taken. It does not appear that inaccuracies in the statistical interpretations have hindered that usefulness. References McClave, J.T., and Dietrich, II, F.H., 1982, "Statistics," Dellen Publishing Co., San Francisco and Santa Clara, CA, 766 p. Snedecor, G.W., and Cochran, W.G., 1980, "Statistical Methods," The Iowa State University Press, Ames, IA, 561 p. Reply by V. Miller After reading Ms. Hertzler's comments, it appears that the differences noted were basically semantics. If the paper is ever presented at a math symposium, some changes will be needed. When deciding the best way to present the data to mining engineers and geologists, I decided that presenting the probability that the two sample groupings came from different populations (reverse to the Null hypothesis) was easier and would require less verbage to explain. Hence, the 100(1 - p) difference which was noted. Ideally, I would have preferred to give the recovery and concentrate grades, then comment which ones had significant differences. Unfortunately, Kennecott Corp. did not grant permission to publish the ore body's actual recoveries and concentrate grades. The conclusion is that there was, as expected, a relationship between the ore's geologic properties and the metallurgical properties, and by determining this relationship, the overall mineral model was greatly improved.

Jan 8, 1984

By H. Richard Eisenbeis, Donna M. Watkins

Many technical professionals (tp)* desire to occupy upper level management positions. But career paths for most scientists and engineers do not extend beyond their specific disciplines. This is unfortunate. Our technical frontiers are expanding so rapdily that it is difficult, if not impossible, to make sound top management decisions without understanding the technical complexities involved. Technical professionals often are not considered for upper level management positions because they lack the managerial and interpersonal skills necessary to become successful administrators. You've heard this before, but a key component of these skills is the ability to communicate. Technical professionals are often unable to communicate as well as they should with nontechnical professionals and nonprofessionals within the organizations that employ them. Communication is important for managerial success Communication is the network of interactions whereby knowledge and understanding are conveyed from one social set to another (Flippo and Munsinger, 1982). In order to be successful, managers must not only be "good" communicators, they must be "effective" communicators as well. Good communication occurs when managers are able to formulate and transmit their messages in such a way that they are received and understood. Effective communication goes one step further: It occurs when recipients accept messages as legitimate and respond to these messages in the manner desired. Before promotion into upper level positions, managers must have developed organizational skills (planning, decision making, organizing, and controlling) and interpersonal skills (directing, influencing, and motivating). Applying these skills effectively is difficult without a highly refined ability to communicate. Effective communication, then, is basic to managerial success. Nowhere, perhaps, has the importance of being able to communicate effectively been emphasized more than in Mintzberg's landmark study of managerial roles (Mintzberg, 1973). Mintzberg's results indicate that executives typically averaged 36 written and 16 verbal contacts a day. These contacts were both important and trivial. They generally occurred in a random manner. Time spent on each varied. Scheduled meetings averaged over an hour. Desk work, telephone calls, and unscheduled meetings required an average of 15 minutes or less. Why technical professionals have difficulty communicating Three reasons why technical professionals do not communicate well are: • The work motivational patterns and personal attitudes of technical professionals are not conducive to effective communication. • Students in technical professions are not encouraged by educational institutions to develop their communication skills. • Organizations do not insist that all technical professionals be able to communicate in the language of business. The work motivational patterns of most technical professionals are indicative of internals and high achievers (Hunt, Salisbury, and Whittington, 1968). As internals, they believe they control their own destinies. As high achievers, they believe that task accomplishment is a primary indicator of success. To ensure a task is completed in the manner desired, tp's attempt to structure and define work situations so they alone are responsible for results. TPs consider the task accomplished when they, and perhaps other tp's, are satisfied with the results. From the tp's perspective, the task may have been completed. From a communication standpoint, two other factors may apply. First, solving the problem required very little interaction (and thus, communication) with others. Second, the tp's, considering the task accomplished, have little concern for how their "technical" answers will be translated to nontechnical persons needing

Jan 8, 1987

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man's house as it was mined. Then it may have been stockpiled at each man's place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

By Stuart R. Cotterill

Open cast surface mining requires blast hole drilling with many interesting facets in order to achieve mine planning forecasts. Interestingly, no single method or combination of theoretical hypothesis of mining economics is right for all conditions. On occasion mine planners introduce a project with little or no regard to drilling and blasting. Generally, drilling and blasting costs are a significant percentage of total mine overhead. One such drilling and blasting method which can be utilized to reduce overall mine expenditure is inclined or angle hole drilling. One must bear in mind, that angle hole drilling per-se mill not reduce costs, unless a set of required circumstances is met. An attempt will be made to detail when conditions of the mine design criteria dictate the use of angle drilling.

Jan 1, 1984

By D. R. Tweeton

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of groundwater quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be performed in two or three weeks. It is relatively inexpensive, requiring one injection- production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin, and was partially funded by the Bureau of Mines.

Jan 1, 1986

By M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low-and high-rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Jan 1, 1997

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By W. J. Miles

Oil based drilling fluids utilize a number of industrial mineral products to accomplish oil and gas drilling in several environments where water based drilling fluids are less effective or inappropriate. These industrial minerals include: organically modified bentonite, organically modified lignite, barite, hematite, mica, calcium chloride and other salts. A variety of organic products are also utilized in oil based drilling fluid formulations. Oil based drilling fluids are preferred in several drilling situations because: they can be used to drill through water sensitive formations; they produce holes that are very close to the drill bit gauge; they exhibit high temperature stability; they are more environmentally acceptable; they minimize producing formation damage; they provide faster drilling rates when used with new polycrystalline diamond drill bits; they minimize pipe sticking and lost rig time.

Jan 1, 1986

By W. H. Strickland

The research reported here characterizes ultrasonic ranging sensors for autonomous navigation on underground mine mobile equipment. Because ultrasonic rangers are inexpensive, have no moving parts, have no lenses to clean, are small and unobtrusive, and can measure distances in dusty environments, they are especially sui ted to underground mi ne environments. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of individual rangers and a ring array of 24 sensors. The results showed the sensors have good accuracy and low variability. Additional experiments at AHAX' s Henderson mine Showed the sensors could accurately and reliably measure rib features, convex and concave corners, and drift intersections. The results showed that when used and analyzed properly, the sensor data may be used reliably for underground mobile equipment navigation.

Jan 1, 1990

By Yashar Pourrahimian, Magreth S. Dotto

Fragmentation by blasting is a critical process in hard rock mining. The blasting process and outcomes are highly influenced by rock mass properties and their response to higher stresses and loading rates. Each rock mass is unique, but some features affect the blast energy similarly, leading to similar outcomes. Having analyzed these features and their influence on blast results, they can be incorporated into the blast design to achieve better outcomes. This paper presents a numerical model validated by a case study from the actual mine blasts that studied the effect of rock mass properties on explosive energy production, attenuations, and overall blast outcomes. The results show that when the model parameters are calibrated based on real data, they can be used to simulate the fragmentation process and therefore be used to aid blast design.

Jun 25, 2023