Search Documents

By C. B. Cecil

The sulfur content of United States coal can be assessed by using a variety of approaches. The sulfur content may be expressed in terms of total sulfur in the coal, pounds of sulfur per million Btu, or sulfur remaining after reduction by coal preparation. In addition, the sulfur content may be applied to the demonstrated reserve base or to coal resource estimates. Unfortunately current data bases do not allow for an integrated assessment at the National level. Although classification of coal resources and reserves according to sulfur content is arbitrary, preferential production of low-sulfur reserves will positively skew the total sulfur of the remaining coal resource.

Jan 1, 1986

By Matthias Neuenschwander, Andreas Theiler, Patrick Steinle, John Singer, Martin Vogel, Diego Martini, Ömer Ündül, Markus Weh

"Quartz Dust is a major health hazard in underground works, wherever the ground contains quartz and depending on the chosen method of excavation. A research project initiated by the Swiss Tunnelling Society and realized by the Swiss Federal Institut of Technology, Zurich, established a correlation between the potential of quartz dust generation during excavation and well known geotechnical characteristics – the Cerchar Abrasivity Index CAI and the Uniaxial Compressive Strength UCS - of ten typical Swiss rocks. The results are at the center of a new guideline by the Swiss Society of Engineers and Architects on the requirements for early project stages regarding ventilation and logistics in function of the quartz dust related risk of the expected ground type of the project. The approach presented could be applied worldwide, contributing to more effective health protection as well as to better cost stability in underground works. CONTEXT Respirable quartz dust (aerodynamic diameter of particles < 10 micron) is universally recognized as a major workplace health hazard. Chronic bronchitis, silicosis and lung cancer can be caused by excessive exposure to quartz dust, as has been proved by many medical studies. Therefore, the legislations of many nations specify a maximum workplace concentration (Maximale Arbeitsplatzkonzentration MAK, Occupational Exposure Level OEL). In Switzerland, for example, the Threshold Limit Value TLV for respirable Quartz or Crystalline Silica imposed by the Federal Committee on Exposure Levels (Grenzwertkommission) is 0.15mg/m3 air. Some nations refrain from establishing a OEL because of the carcinogenic nature of quartz."

Jan 1, 2016

By J. A. Madonna

Independent prospectors and small to large-scale exploration company personnel have requested, and are in need of, guidance in geochemical field sample collection methods which will provide the most reliable results during chemical analysis. In cooperation with analytical laboratories, experienced geochemical exploration scientists and mining companies a systematic collection procedure has been developed. The procedure consists of collecting uncontaminated, water, sediment and rock chip samples of the appropriate quantity and/or dimensions to meet the needs of analysis.

Jan 1, 1999

By H. L. Lovell

The growing production of fly ash with the many attendant problems of economics, disposal and potential uses suggests an urgent need to consider those properties which are basic in its beneficiation. Fly ash is extremely variable and heterogeneous in all respects except its fine size. Because of its production in huge quantities, it becomes significant as a potential raw material. Detailed data are presented describing particle size and shape, density distribution and magnetic characteristics. The major components include combustible residuals, magnetite and silicates. These data are discussed in terms of beneficiation processes and uses, The results of air classification to produce a uniformly fine-sized low combustible product are encouraging. It is proposed that major increases in the future use of fly ash, must involve some form of beneficiation. Both the coal producing industries and the consuming utilities would benefit from increased utilization.

Jan 1, 1964

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott&apos;s conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By Thomas V. Falkie

The title of this talk has brought some interesting responses - even before it was written - from different parts of the country. A geologist from the Western U. S, was deeply concerned with recent layoffs in his profession and the employment situation in general and wondered why "the AIME wasn&apos;t doing anything for the benefit of its members." A petroleum engineer in Texas said that a group in his field were studying "professionalism" and their professional status and wondered if there were any words of wisdom for him. A mining engineering professor from the East pointed out that the National Science Foundation did not include mining engineering as one of its recognized fields in one of its equipment funding programs. These are just a few examples of reactions received to date, but they serve to illustrate the broad image that the title has meant to various people. Actually the term profession is defined by Webster as "a calling requiring specialized knowledge and often long and intensive academic preparation." The word encroach means "to enter by gradual steps or by stealth into the possessions or rights of another", or "to advance beyond desirable or normal limits." The intention of this paper, as originally conceived and requested by the program chairman, was to combine those two words literally and talk about how the professional standing of mineral engineers is being eroded from people outside the profession. But the amazing preliminary response suggests that it may be timely to broaden the discussion by including some comments about professionalism in general. In the paper the terms "mineral engineer" or "mining engineering" are used frequently, but it should be clearly understood that much of what is said is valid and is intended for all fields covered by SME and perhaps for AIME in general.

Jan 1, 1972

By Haydn H. Murray

Kaolin is defined and described as an industrial mineral. In addition the types of deposits -primary and secondary are defined and the genesis of kaolin from feldspars and other minerals discussed. The major deposits of the world found in the United States, Great Britain, Brazil, and Czechoslovakia are described along with many of the minor kaolin deposits. Four areas which have very large deposits of kaolin could, with technological breakthroughs to reduce viscosity significantly, become important factors in supplying the world markets which are increasing year by year.

Jan 1, 1977

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980

By Harry Perry

The Bureau of Mines is glad to have this opportunity to discuss its present Coal Research Program and its significance to the industry with a group which has for many years been representative of the coal producing community. We believe we have a dynamic program that will help our vast coal resources to find their proper place in the U. S, economy. The present coal research activities of the Bureau are conducted in three organizational subdivisions: Minerals Research, Mineral Resource Development, and Health and Safety. All investigations are carried out in Bureau research facilities located in different sections of the country, Since its creation by the Organic Act of 1910 and subsequent amendments, the Bureau has worked closely with the coal industry--first by providing assistance in mine safety for anthracite and bituminous coal mining, and since that time, in providing information on conservation, safety, mining, preparation, and utilization.

Jan 1, 1966

By George Dials

Good morning gentlemen. My name is George Dials, and I am [vice] president of the Mining and Reclamation Council of America (MARC). The Council is composed of various companies, individuals, and affiliated state and regional trade organizations representing nearly 3,000 companies directly and indirectly involved with surface coal mining in the United States. I am very glad to be here today to address the Society of Mining Engineers of AIMS. While I do not pretend to be an expert in either geological or geotechnical engineering, I am infinitely familiar with the provisions of the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87) and the Federal regulations that have been promulgated pursuant to that Act. The Office of Surface Mining Reclamation and Enforcement (OSM) was created by P.L. 95-87 within the responsibility for implementing the provisions of the Act and "to ensure that society and the environment are protected from the adverse effects of surface and sub-surface coal mining operations."

Jan 1, 1979

By T. Lupek, M. Buxton, A. de Jong

"With regard to the EU funded project ‘Real-Time Mining’ a sensor-based acquisition, collection and transmission of data for the resource extraction process will be developed. The key concept promotes the change in paradigm from a discontinuous to a continuous process monitoring. Especially concerning material characterization, machine performance and underground positioning ‘Real-Time Mining’ will provide sensor solutions as well as the interfaces for integration, management and visualization of the collected data for a permanent updating process of the resource model with the aim of near real-time optimization of decisions. On the basis of ‘Real-Time Mining’-Output a permanent monitoring of costs can be performed as well in both, the installation and the production process of a mine. Due to the collected data in terms of machine performance connected with the underground positioning information added with personnel tracking and mine surveys a comprehensive overview of process performance is available. By evaluating those information in a specific manner costs per unit will arise for monitoring and possibly controlling actions. INTRODUCTION By having a look into the future of mineral extraction projects, a new challenge for the Ore Mining Industry will arise in the short and medium term. Due to the depletion of currently mined mineral reserves in addition to the persistently high demand of mineral raw materials, the extraction of complex reserves will be necessary. By characterizing such deposits as not constantly graded and geometrically varying, the extraction process, especially concerning the requirement of a minimized zero-value material handling, will become economically ineffective by utilizing the traditional mineral resource management methods. Regarding the state-of-the-art mineral resource management process along the mining value chain, an intermitted, discontinuous sequence of actions is applied (Figure 1). Recently data will be collected from drill hole cores. These rock samples are analyzed in a laboratory. Based on those analyses a resource model is created whereby unknown data between drill holes is interpolated. This resource model is the basis for all mine planning actions including the selection of the mining method, extraction sequencing and the prediction of the expected performance. With the start of the production, real conditions (concentrations of elements, hardness, stability, etc.) can be observed and measured. As the production process is running accordingly to the above described mine plan, the verification of the initial assumptions happens at the earliest after processing of the extracted material. Even if deviations between the predicted and the actual performance are now recognized, the execution of corrective actions is not possible anymore."

Jan 1, 2016

By S. S. Sephton

The La Perla Mine, owned by Altos Hornos de Mexico, S.A., is located approximately 100 miles east of the City of Chihuahua in the State of Chihuahua, Mexico. The mine began operations in 1958. Existing ore beneficiating facilities, consisting of heavy media and jig plants, upgrade the ore prior to shipment by rail to the Altos Hornos steelmaking complex in Monclova. Sizable reserves of two distinct ore types, which were not amenable to treatment in the existing beneficiating plant, or usable in the blast furnaces, have been mined and stockpiled in order to uncover the treatable ores. One of these ore types has been labeled "Diseminado" ore, and is low grade containing approximately 42% Fe with sulphurs ranging from 1 to 2%. The other ore type has been labeled "Pulverulento" ore, and is high grade containing approximately 65% Fe and 0.1% S, but at 80% minus 325 mesh, is too fine grained for efficient sintering. Late in 1968, Arthur G. McKee & Company became involved with the problem of improving the above ores for their efficient and economical use in Altos Hornos&apos; blast furnaces. Early in 1969 representative samples of Diseminado ore were obtained for laboratory bench-scale testing at the University of Minnesota, Mineral Resources Research Center. Concentration tests incorporating magnetic roasting, wet magnetic separation, high intensity separation, high tension magnetic separation, anionic flotation of apatite, cationic flotation of silica and oleic acid flotation of iron were performed. Laboratory testing was concurrently carried on at La Perla Laboratory, which resulted in plans to construct a 10 TPD pilot plant. The pilot plant was operational in September, 1969. Analyzing laboratory results as well as pilot plant results, Altos Hornos and Arthur G. McKee & Company metallurgists agreed that the most promising flowsheet for the low grade Diseminado ores entailed wet magnetic cobbing, desliming, and oleic acid flotation of the non-magnetic fraction. A combined concentrate of

Jan 1, 1972

By Paul H. Earl

This paper discusses the evolution of a modeling methodology for explaining price behavior in the aluminum industry. Three generations are described, each utilizing as a foundation a microeconomic stages-of-processing approach. The second generation represents an improvement over the initial version, by incorporating more rigorous specifications of energy cost, and market strength (demand-supply balance) as well as endogenous treatment of market strength. International linkages across prices, costs, and markets, are the major extensions in the third generation. The discussion covers theoretical considerations, data problems and limitations, and model specifications. Simulation and forecasting properties of the models are also addressed.

Jan 1, 1979

By G. V. Sullivan

The Federal Bureau of Mines examined tailings samples from 13 western copper operations to determine the potential for recovering rutile. Results showed that six of the samples contained sufficient liberated titania to be considered potential sources. One sample contained 0.75 percent Ti02 or 0.40 percent liberated rutile. Batch flotation studies developed a procedure that recovered 70 percent of the liberated rutile at a grade of 34.7 percent TiO2. Sulfuric acid leaching studies on 12 of the samples dissolved 100 to 2,200 grams Cu per ton of tailings; leaching of the slimes showed slightly more copper was dissolved, 1,800 to 3,300 grams Cu per ton of minus lo-micrometer material. Bulk sulfide flotation of nine of the samples resulted in concentrates that contained 0.38 to 2.0 percent Cu and 0.7 to 2.1 and 6.9 to 42.9 grams per ton Au and Ag, respectively.

Jan 1, 1981

By R. C. Runvick

Gypsum resources are significant in the midwestern United States, with specific deposits varying in "place value" relative to the major markets served. Underground and surface mining operations produce gypsum from sedimentary rocks ranging in age from Silurian through. Jurassic. Although reserves tend to be limited at individual operating properties, potential resources are vast and future development will hinge principally on market growth and changing economic conditions. Most critical of the variables affecting the industry in both the short and long term will be the availability, type and cost of energy and both processing and distribution.

Jan 1, 1980

By S. A. Lolon, J. F. Brune

"INTRODUCTION In underground longwall coal mining, the mined-out areas or gobs frequently contain methane which can form explosive methane-air mixtures. Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of such explosive mixtures, herein referred to as Explosive Gas Zones (EGZs), inside and around the perimeter of bleeder-ventilated longwall gobs (Loane et al., 1975; Lynn et al., 1986; Elkins, et al., 2001; McKinney et al., 2001; Dziurzynski and Wasilewski, 2012; Brune, 2013). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Several factors can induce EGZs outflowing from the gob, but the most common cause is the fluctuating barometric pressure. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Other sudden pressure changes can result from roof falls, failing ventilation controls and fan outages. Any such fluctuation of mine ventilation pressure will disturb the pressure differential between the gob and the surrounding mine workings and may cause EGZs to outgas from the gob. The correlation between major mine explosions and abrupt barometric pressure changes has been studied and confirmed for explosions in coal mining countries including the United States, South Africa, Australia, and Poland (Hosler, 1948; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Hemp, 1994; Wasilewski, 2014; Belle, 2014; and Lolon, 2017). Disastrous mine explosions appear to happen more frequently during stormy weather, which, in the United States, typically occurs during the late fall and winter seasons. ROOT CAUSE AND EFFECT OF GOB BREATHING Gob breathing is the result of the pressure differential between gob internal and external pressures caused by external atmospheric pressure fluctuations that occur naturally as a result of gravitational and thermal forces in the atmosphere (Lindzen and Chapman, 1969). Other major and sudden pressure changes may be caused by fan failures, failures of ventilation controls or roof falls can also cause an unexpected gob breathing. Normal barometric fluctuations occur every day but usually do not pose an explosion risk as they occur gradually so gob pressures have sufficient time to equilibrate. More extreme fluctuations associated with cyclonic weather systems and storms often result in more rapid and larger drops or rises in barometric pressure (Hosler, 1948; Fauconnier, 1992). A study by Lolon (2017) found that the timing of historical mine explosions showed consistency with the occurrence of abrupt and intense barometric variations."

Jan 1, 2018

By Paul Soros

The Conneaut, Ohio, terminal of the Bessemer & Lake Erie Railroad was the first rail-to-ground-to-water coal terminal on the Great Lakes. Compared to the traditional method of holding coal in railroad cars at the ports for dumping their contents into vessels, it provided for: a. Immediate train turn-around independently of vessel arrivals. b. Winter storage of coal at the port, permitting year round shipment by the mines and year round operation of the railroad.

Jan 1, 1969

By Warren N. Warhol

The mutual growth of the rare earth industry and the Mountain Pass Operations was no coincidence. It was the commercial availability of rare earths on a scale first made possible by the capacity of the Mountain Pass Operations that spurred research and development efforts toward new applications for rare earths. The first important demand on Mountain Pass was europium oxide for the activation of red phosphor for color television tubes in 1964. Since that time, other rare earths have become even more important, and Molycorp is continuing to supply an ever widening variety of rare earth concentrates and compounds. We enjoy saying that rare earths are not really rare, and that they are not earths, either. Of course, we are talking about the 15 metallic elements with atomic numbers 57-71, called the lanthanides, which occur in nature always together in very similar proportions. Their scarcity can be gauged by the fact that there is more cerium in the earth&apos;s crust than there is tin, and more europium than cadmium. The word "earths" comes from the early chemical term for oxide. The rare earths were discovered as oxides, and the term has persisted.

Jan 1, 1980

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for all concerned people. The coal industry has taken great measures to reduce both types of pollution. Through the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. In many cases, the complete elimination of thermal drying by using centrifugal dryers to dewater fine coal products and meet customer specifications has completely eliminated air pollution from this source. To help eliminate stream pollution and the hazards created by tailing ponds, the coal industry is using centrifugal dewatering equipment. Use of centrifugals to dewater fine refuse for disposal would eliminate refuse ponds or extend their life. In doing this effectively and economically, preparation plants have the option of recycling the clarified water to close the water circuit or of discharging the water into receiving streams with the assurance that it contains an acceptable amount of refuse solids.

Jan 1, 1974

By Ulrich O. Lange

Coal is America&apos;s most abundant energy resource. Therefore, it IS logical to assume that coal must be produced in much greater quantifies in order to make the United States self-sufficient, as far as energy is concerned by 1985. However, there are a number of obstacles which have to be overcome in order to achieve such a great task. According to one of the most outspoken American Mining men, there are three major obstacles. Those are: (1 ) Mining technology (2) Public image of the coal mining industry (3) Governmental policy toward the mining industry The following will be dealing with Shortwall Mining, which is a very specific part of mining technology and which might influence the image of the coal mining industry as well as the governmental guidelines, at least to make it easier to live with those guidelines. During recent years the operation of coal mines has been more expensive than ever. Since 1970, the cost of producing coal increased by 30% and the productivity dropped by just about the same amount. Those are alarming signs.

Jan 1, 1975