Search Documents

By E. Berrezueta

Automatic digital phase imaging should yield unbiased and representative characterizations of gold ores. However, this is not a simple tusk due to low gold grade, fine grain size, possible complex mineralogy, nugget effect, etc. Using the same sections of a gold-rich ore, a critical test was performed using an optical microscope (OM) and an electron microscope (EM). In general, the two methods are consistent and useful for ore processing. There are some minor differences, such as the detection of very fine gold grains is enhanced by EM. Key words: Digital imaging, Gold ores, Mineralogy, Electron microscopy, Optical microscopy

Jan 1, 2003

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By B. Alegria

The depressing effects of different inorganic chemicals on the flotation of pyrite have been investigated in this study. The results of the flotation tests indicate that pyrite can be depressed by oxidizing as well as reducing agents under controlled conditions of pH and reagent dosage. Oxidizing reagents such as potassium chromate and potassium dichromate were found to cause complete depression of pyrite in the acidic pH range. These effects are similar to those obtained in the pyrite-cyanide system. A less stable oxidant, potassium permanganate, inhibited the flotation of pyrite at a concentration as low as 0.1 mol/L at all pH values, Addition of reducing chemicals such as ferrous chloride or manganous sulphate to the flotation of pyrite were found to produce depressing effects depending on the additive concentration and pH of the solution.

Jan 1, 1982

By George C. Toland

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control on the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. This paper discusses the types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent, and discusses in detail technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1975

By K. V. Raj

"The development and advancement of computational fluid dynamics (CFD) has made it possible to better understand pollutant flow and distribution in deep open pit mines. Open pits located at higher latitudes, especially in the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during much of the winter. A three-dimensional CFD model of an actual open pit mine in the Arctic was developed to analyze the problem of pollutant growth during inversion, and mitigation of the pollutants through improved ventilation schemes. Due to the availability of mine-specific data, such as contaminant concentrations and coordinates of sampling locations, the actual 2013 pit geometry was used for model validation Concentrations predicted by the selected realizable ?-e turbulent model are compared to measured pollutant concentrations at the open pit. Pollutant concentrations at selected locations showed differences, but remained within the same order of magnitude in most cases. INTRODUCTION Computational fluid dynamics (CFD) has emerged as a useful tool for ventilation modeling in underground mines (Edwards and Hwang 1999, Purushotham and Bandopadhyay 2009, Wala et al. 1998, Xu et al. 2011). Application of CFD in open pit mines has been limited, however, since most open pit mines located at lower latitudes do not encounter considerable ventilation problems. Open pits located at higher latitudes, especially the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during winter. A number of Russian researchers have tried to understand the air inversion and resulting pollutant transport problem by modeling air flow phenomena in open pit mines (Baklanov and Burman 1996, Baklanov 1984, Baklanov 1995, Belousov 1985, 1989, 1995). Much of their work, however, was based on numerical models and methods of finite difference. Baklanov (2000) applied a modified ?-e and a ?-l CFD model to air flow phenomena on various terrains. More recently, Choudhury (2011) used the COMSOL CFD package for modeling pollutant transport for an idealized open pit mine. Collingwood et al. (2012a, 2012b) used a two-dimensional model for fluid flow and contaminant transport at an Arctic open pit mine. The authors have also previously presented work on CFD modeling of an actual open pit mine at high latitude (Bandopadhyay et al. 2014, Raj et al. 2015a). However, the CFD work done by the above-cited researchers lacked model validation with field-measured data. Validation of a developed model is important in assessing the quality and accuracy of the predicted results. In general, experiments are done numerous times in controlled environments to assess the validity of collected data. There are two types of assessments used in CFD simulations: (1) verification and (2) validation. Model verification is checking the accuracy of the computer codes during the implementation phase of a real-world problem, within the specific limits of accuracy (Oberkampf and Trucano 2002). Since, the pollution transport model presented in this paper used the commercial ANSYS-FLUENT CFD package, verification is not needed as the program has been tested widely, and verified numerous times."

Jan 1, 2016

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By Joseph E. Worthington

Increases in the price of gold starting about five years ago, and rapid fluctuations since then, have caused a substantial popular interest in the noble metal. Gold prospecting had been at low ebb since the end of World War II in most of the United states except for a flurry of activity in Nevada occasioned by the Carlin and Cortez discoveries. The last five years, however, have seen a great awakening of interest in gold exploration as well as an opportunity for education for many explorationists in the geology and other vagueries of gold deposits. The present writers have participated over the last few years in a search for gold deposits throughout the United States. This search was greatly influenced by the geologic studies of Dr. Wm. Spence at the Haile Gold Mine in South Carolina as reported in a companion paper. Spence's studies resulted in definition of a geologic model that has proven useful in a number of other geologic environments in the united states. These programs were all carried out under the auspices of Cyprus Mines Corporation and permission by Cyprus to present these results is gratefully acknowledged. The writers, however, reserve for themselves all responsibility for the results and conclusions. The exploration program to be described began in the southeastern United States. Spence's studies provided a reasonable basis for interpreting and understanding the geology of the Haile deposit and also provided a means for predicting additional occurrences. This concept was then expanded to other gold occurrences in the Piedmont and became an effective tool for evaluating other prospects. Finally it became evident that the concept could be applied in some western gold districts. The following discussion will then include descriptions of other Piedmont examples and a few western districts that also appear to fit the pattern.

Jan 1, 1978

By M. D. Lawton

Anglo-Rouyn Mines Limited, managed by Rio Algom Mines Limited is a subsidiary of the British-based Rio Tinto-Zinc Corporation Limited. This mining operation is situated in Northern Saskatchewan, 250 miles north of Saskatoon and represents the first base-metal mine of any importance served by this relatively new mining province. The outcrop of Copper-bearing Chalcopyrite was first discovered by prospectors in 1915, but was not mined until 1965 due to the absence of any form of road into the area prior to this latter date. The mine, mill and concentrator were designed to handle 900 tons per day of comparatively hard, abrasive ore containing chalcopyrite with traces of gold and silver. The flow sheet, Figure 1, is, we believe, elementary, designed with low cost in mind and utilises much old equipment from closed¬-down mines. Due to some difficulty in attaining the designed grinding capacity, changes were made in the crusher circuit. This, unfortunately, lowered the crushing rate too much. A series of changes have taken place to re-establish the original crusher capacity of better than 100 tons per hour. In the quest for a better recovery certain modifications have been tested in the concentrator circuit. These steps are discussed in minor detail.

Jan 1, 1970

By L. Xia, B. Hart, V. Sidorkiewicz

Sodium silicate(s), also known as “water glass”, are one of the oldest and most widely used industrial chemicals. Its first use in North American mining operations can be traced back to around 1925, which coincided with early use of xanthates in mineral flotation. Silicate functions as a sulphide and non-sulphide gangue mineral dispersant, depressant and modifying reagent in grinding and flotation operations. It is believed that soluble sodium silicate promotes selectivity of value added sulphides against gangue minerals, resulting in both grade and recovery improvement. This paper seeks to link improved grade/recovery to the interaction characteristics of minerals and the sodium silicate. A systematic study was performed with individual mineral species, an artificially designed model ore and the feed ore from a copper metallurgical operation. The function of sodium silicate was evaluated in the context of colloidal chemistry and linked to mineral surface chemistry. Measurement of pulp rheology and mineral zeta potential identified that sodium silicate works as a dispersant. The dispersion is accomplished by increasing a mineral’s net surface charge, resulting in a mineral variable change in viscosity. Bench scale laboratory flotation tests suggest that better dispersion leads to a diminished interaction of chalcopyrite with gangue. The improved Cu grade and recovery then are likely in response to an increased accessibility to collector along with a linked increase in particle bubble attachment resulting in better separation efficiency. ToF-SIMS surface chemical analysis of the flotation samples found a higher proportion of sodium silicate on minerals from the flotation tailings relative to the concentrates. Moreover, attachment of sodium silicate appears to be mineral specific; the data indicates that sodium silicate favours the surface of gangue phases over the value sulphides. INTRODUCTION Mineral processing involves enrichment of valuable minerals from an ore, where the separation process utilizes differences between the properties of the value-added and gangue minerals. The properties of minerals, for example composition, specific gravity, particle size, magnetic properties etc., in any flotation feed ore, can vary significantly between the various minerals present. In flotation seperation surface chemistry and wettability is a significant component promoting selective separation of the various mineral phases [1,2] Mineral surface wettability can be changed, advantageously or deleteriously, by many factors including: surface layer alteration through oxidation; galvanic interactions; attachment of secondary precipitates; the adsorption of various reagents [3] In the flotation context the wettability of a minerals surface can be manipulated by various reagents. Collector reagents may selectively attach to specific minerals in the mineral/water slurry enhancing their surface hydrophobicity, increasing bubble-attachment efficiency and improve flotation kinetics and mineral recovery [4]. In contrast, depressant reagents may selectively reduce a minerals surface hydrophobicity resulting in poor particle-bubble attachment and non flotation. In essence, a mineral flotation flow sheet is designed to induce/promote a hydrophobic surface to the value mineral and a hydrophilic surface to all others. Therefore, the versatility of the froth flotation process lies in the selection of different flotation reagents.

Jan 1, 2019

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By Patrick Sullivan

Over the past few years, successful operations for processing phosphates employing the Grate-Kiln System have been achieved. Control and instrumentation philosophy followed in these installations are described and analyzed. Concepts utilizing digital techniques and computer systems appropriate for similar installations are also discussed.

Jan 1, 1967

By Robert H. Carpenter

Abstract, Syngenetic uranium in pre metamorphic Idaho Springs volcanics and sediments probably, was mobilized during metamorphism (1.7 b.y.) and partly retained along unconformities. Precambrian Silver Plume intrusives (1.4 b.y.) and Pikes Peak granite (1.0 b.y.) may have mobilized uranium from the craton and. Idaho Springs metamorphics to concentrate it in cauldron sites in migmatites, pegmatites, alaskite, disseminations and greissen. Tertiary intrusives also may have upgraded uranium by anatexis, leaching and differentiation. Tertiary vein and shear zone uranium mineralization may have-been-derived from underlying magma sources, leached from Idaho Springs metamorphics and from syngenetic leaching of overlying sediments and introduced by deep hydrothermal convection systems.

Jan 1, 1979

By R. S. Kinasevich

As part of other work related to the studies of kinetic factors that influence the flotation of specific sulphide minerals, specially designed kinetic flotation experiments at Cominco included work done on -65 + 100 mesh and -100 + 150 mesh, high purity galena. The flotation collector used was sodium isopropyl xanthate containing radioactive sulphur-35. Radiation monitoring of the galena fractions from stage flotation tests indicated that the adsorbed radioactive xanthate was uniformly distributed among the floated fractions and the non-floated, or residual portion of the galena. This anomalous behaviour could not be correlated to changes in Seebeck coefficients, to lattice distortions, or to the nature of the mineral surface as revealed by infrared spectroscopy and by microscopic measurements.

Jan 1, 1970

By James E. Breland

Society's growing concern over the number of deaths and serious injuries occurring in coal mines, coupled with a growing sentiment to develop and promulgate improved mandatory health or safety standards, was no doubt the basis for passage by Congress of the Federal Coal Mine Health and Safety Act of 1969, being Public Law 91-173 approved December 30, 1969. Even prior to passage of the Act, strong reaction was quick to arise concerning the effect of such legislation upon the coal mining industry. Initial response varied from mild forms of criticism to' the expressed fear of complete suspension of operations and mine closings. Primarily responsible for these early forms of skepticism were speculative or fanciful cost estimates which led operators to contemplate a less than prosperous existence. However, in spite of this unfavorable outlook, the majority of the operators have faced up to the situation and have been striving to comply with the Act and the regulations issued thereunder. While encouraging strides have been made toward implementation of the Act, it must be recognized that noticeable results have been attained only through many months of determined effort and, as anticipated, at quite heavy expense to the operator.

Jan 1, 1973

By H. K. Pelzer

Belt conveyor systems for long-distance haulage are nowadays in a competitive position with conventional methods of transportation such as railways, truck haulage, and also pipelines for solid materials. In a number of cases, the economical use of conveyors is obvious. This is in all those cases where typical features of a conveyor system are showing the outstanding economical position in the very first approach for a certain project. Regarding downhill conveyors, with today's level of belt conveyor techniques nobody would reasonably doubt the justified application of a conveyor system, - as for instance at the Marcona Mining Installation, or at the iron ore mine of Lamco in Liberia.

Jan 1, 1968

By James D. Cooper

Long range projections of demand for nonmetallic minerals are presented, together with data on the domestic resources which are available or which can be made available to meet the requirements through the balance of the century. Past successes in solving nonmetallic mineral requirement problems are briefly reviewed to illustrate the capability for solving present and future problems of a similar nature. Major problems threatening the future supply of specific industrial minerals are described together with possible methods for assuring the necessary raw materials for future needs. The growing importance of environ- mental degradation, land use conflicts, and other important factors which affect several or all of the nonmetallic mineral industries is covered, and the necessity of planning for efficient and orderly extraction and rehabilitation of mineral deposits is stressed. The present Bureau of Mines methods and tools for long range planning are briefly discussed.

Jan 1, 1969

By Yehia M. Youssef, Nourhan Moukhtar, M. H. Abdel-Aziz, Ibrahim Hassan

Copper was recovered from copper sulfate solution in a batch-recycled galvanic reactor operated under forced convection with the generation of electrical energy during the cementation process. The divided galvanic cell consisted of parallel copper and zinc plates. The mass transfer rate and the amount of electrical energy generated were found to be directly proportional to the solution flow rate and the initial concentration of metallic ions and inversely proportional to the distance between electrodes. The experimental results were expressed in terms of a dimensionless correlation including all parameters. The wastewater treatment presented herein cell can be utilized to recover many soluble heavy metal ions from solution with high efficiency.

Oct 2, 2020

By Nomuqhele N. Nkosi, Yasuo Yabe, Musa D. Manzi, Raymond J. Durrheim, Siyanda B. Mngadi

This study examined rock failure in brittle rocks hosting the deep gold-bearing ore bodies on scales between millimeters and kilometres. This research study is part of the International Continental scientific Drilling Program (ICDP) project, “Drilling into Seismogenic Zones of M2.0-M5.5 earthquakes in deep South African gold mines” (DSeis). The broader ICDP-DSeis project aims include the examination of the extent of damage, the stress state around the fringes of the earthquake, and the potential existence of living organisms associated with deep-level earthquakes. Nevertheless, this study focused on two seismogenic zones – the Cooke 4 mine and Moab Khotsong mine. At Cooke 4 mine, the study examined the evolution of mining-induced fractures (M1-4) occurring ahead of the stope face during the extraction of the remnant shaft pillar. These fractures were monitored and delineated by a dense array of acoustic emission sensors that allowed hypocentres to be located with decimeter accuracy. Using this acoustic emission data, the DSeis team drilled and recovered the fractures, rock breccia and gouge using a sophisticated triple-tube drilling rig.

Apr 26, 2022

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese alloys are important raw materials for steelmaking. However, selective mining of high-grade manganese ore resources has resulted in a scarcity of these high-grade Mn ores (Mn: >42; Mn/Fe: >5). The present research work is carried out to explore a new smelting reduction process to produce high-Mn/Fe syntheticMn ore from low-grade ferruginous manganese ores. Representative samples of low-grade ores (Mn: 25–30%; Mn/Fe: ~1) were collected and smelting reduction studies were carried out using variable smelting power (20–30 kWh), carbon rate (10–20% of ore) and slag basicity (0.1–0.3) to produce high-MnO slag and manganese pig iron. Studies have shown that different-grade high-MnO slags (MnO: 38.57–58.24%; Mn/Fe: >15) and manganese pigs (Mn: 5.16–24%) can be produced at optimum process conditions. The high-MnO slag can be used as synthetic ore for the ferroalloy production process. The developed process is capable to effectively segregate the iron and manganese in the metal and slag, respectively. The optimum Mn and Fe separation (>95%) was achieved by smelting of 10 kg Mn ore batch in a 50-kVA electric arc furnace using 30 kWh smelting power and 0.16 kg of coke. The slag basicity was maintained at 0.3 and the optimum slag SiO2 was ~30%. The studies indicated that the upgrading of low-grade ferruginous manganese ores is a promising solution for achieving high-Mn/Fe-ratio synthetic ores for ferroalloy production. It can help the manganese alloy industry to overcome challenges associated with the scarcity of high-Mn/Fe-ratio Mn ores and efficient utilization of low-grade resources.

Aug 3, 2020