Search Documents

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão Mine in Brazil. They are predominantly blue apatite, followed by green apatite and, less frequently, yellow apatite. The chemical compositions of these types of apatite were determined by electron microprobe analysis and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). Blue and green apatite responded well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite has the lowest phosphorus pentoxide (P2O5 ) content and largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest phosphorus (P) and calcium (Ca) grades and lowest substitution level.

By J. Diaz

"Antioquia region, in Colombia, is considered one of the areas with the highest mercury contamination in the world due to its use in gold recovery through artisanal mining, emissions to the environment between 100 and 150 tonnes of mercury are estimated by year. Therefore it became necessary to develop a project in which it was proposed aim to empower traditional artisanal mining community, or in different areas, such as gold mining in the region of Antioquia, in the implementation of safe mining practices and environmentally sustainable, from the introduction of clean technologies, in order to prevent or mitigate the impacts generated by traditional mining on the environment and the communities involved. In order to achieve this training to traditional mining community developed and technical visits to artisanal mining were performed in order to optimize operating processes and promote safe mining practices. In the project more than 1400 artisanal miners were trained.INTRODUCTION In the developing world, a combined 30 million individuals extract more than 30 different minerals using rudimentary techniques. Gold is the preferred mineral extracted by artisanal operators due to its high unit value and its market price, which has increased almost sevenfold over the last decade (Veiga et al, 2014). The artisanal gold mining sector in Colombia has 200,000 miners officially producing 30 tonnes Au/a. In the Northeast of the Department of Antioquia, there are 17 mining towns and between 15,000 and 30,000 artisanal gold miners (M. Veiga, 2010) (Upme, 2014). This production, however, has caused environmental problems, including high levels of river siltation and mercury pollution (Veiga et al, 2014) (UPME, 2007) (Cordy et al., 2013). The mercury contamination in Colombia by artisanal gold mining has been recognized by a number of researchers and local authorities for over a decade estimated that the annual mercury emissions from artisanal gold miners in Colombia in 2007 were between 50 and 100 tonnes, however given recent gold value increases and gold rush activity, current mercury emissions are likely much higher. Colombia is likely the world's 3rd largest source of mercury emissions from AGM after China (240 to 650 tonnes of Hg/a) and Indonesia (130 to 160 tonnes of Hg/a) (Telmer and Veiga, 2008) and is the world's highest per capita mercury polluter (M. Veiga, 2010)."

Jan 1, 2016

By Brian Ulrich

The majority of individuals involved in the mining industry can appreciate and under-stand that mining is an activity that is necessary to satisfy the very basic needs of society, and to assist in accommodating our ever-changing world. As the expression goes, ?if it can?t be grown, it has to be mined.? And at this point in time, society has granted the mining industry the right to go about the business of mining, with the general anticipation that the work will be carried out without causing undue harm to the environment or populations in and around the mining operation. The term ?sustainable development? is gaining momentum as a popular concept, and indeed it has become something of a catch-all phrase, but it is important that the idea behind the term is not cast aside as a nonsense buzz word, as it simply is an indication that development (e.g. mining) can be satisfactorily carried out with an eye toward stewardship of the environment and society. On Feb. 19, 2010, a round-table discussion (Roundtable 2010) on ?Strides Toward Sustainability in Mining? was hosted by Knight Piésold and Co. (Knight Piésold) at the Red Lion Inn and Casino in Elko, NV. Knight Piésold had local representatives (Bryan Ulrich and Steve Boyce), as well as representatives from other office locations (Cynthia Parnow and Rick Damiani from Denver, CO, and Rick Frechette from Tucson, AZ) to help facilitate the discussion. The meeting played host to 30 attendees from five states. Attendees included personnel from nine mining properties and various corporate offices. The majority of participants were people who are directly involved with environmental work on a day-to-day basis. Others were project managers whose jobs involve some level of environmental focus.

Jan 1, 2010

By S. Tyson

The American Coal Ash Association, Inc. (ACAA) is an organization of producers and marketers of coal combustion byproducts. Since 1968, the goal of ACAA has been to gain recognition and acceptance of ccbs as an engineering material on par with competing virgin, processed and manufactured materials by advancing ccb uses that are technically sound, commercially competitive and environmentally safe. The use of ccbs is affected by local and regional factors including production rates, processing and handling costs, transportation costs, availability of competing materials, seasonal adjustments, and the experience of materials specifiers, design engineers, purchasing agents, contractors, legislators, regulators, and other professionals. An annual, survey of coal-burning electric utilities is conducted by ACAA to determine the quantities of ccbs produced and used in the USA. In 1993 approximately 88.5 million tons of ccbs were produced in the form of fly ash, bottom ash, boiler slag and byproduct from flue gas desulfurization (FGD). Approximately twenty-two percent of the combined production of these byproducts was used, while the remaining portion was deposited in disposal areas. The major markets for ccbs include cement and concrete products, structural fills, road-base layers, mineral filler in asphalt, grit for snow and ice control, blasting grit and roofing granules, grouting, coal mining applications, and waste solidification and stabilization.

Jan 1, 1995

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

By Clement K. Chase

Although flotation is the generally accepted process employed to recover gold and silver as well as copper, lead, and zinc from primary sulfide ores, the metallurgical requirements for the treatment of massive sulfide ore deposits differ markedly in many respects from those employed for the more common disseminated porphyry deposits. In Arizona, some properties classified as other then massive sulfide deposits because of mining and geological characteristics have produced mill-feeds similar to those from massive deposits. Several such occurrences are noted. The process requirements for massive sulfide deposits and unique mill-design implications are discussed in the perspective of world-wide economic considerations and the individual regional metallurgical and economic constraints in the United States.

Jan 1, 1986

By R. Eggert

Since the discovery of high temperature superconductors has led to extensive interest and conjecture regarding their potential to change contemporary technology, discussions of the impact on the metallurgical and other industries have naturally arisen. In this paper we present data showing the possible impact of these developments on the materials related to the fabrication and proliferation of devices based on superconductor materials. We observe that the largest volume of effort with LTSC will be for the demonstration of high power devices while applied research relating to processing will remain the principal HTSC activity. We also note that in the next decade copper consumption in the US is expected to remain essentially at the current level while the need for Nb and Sn,; two major components of LTSC, will grow at a faster rate both in the US and the world. Although the use of superconductor-based magnetic separation is anticipated to increase, no major impact of these components on the metallurgical industries is expected.

Jan 1, 1990

By Carrie Smith

Mining has historically been one of the most male-dominated industries in the world. From underground operations to executive boardrooms, the presence of women has often been slim. Women had often been excluded from operational, leadership and decision-making roles, both by cultural norms and systemic barriers. According to PwC’s Global Mine Report (2023), women represent around 14 percent of the global mining workforce. Leadership representation, however, remains sparse, with S&P Global’s 2023 report showing women holding approximately 12 percent of C-suite positions and only 3 percent of senior leadership roles globally. These figures reflect persistent gaps, but they also highlight the progress driven by a new generation of women transforming the industry. Despite the gender imbalance among mining workers, women have continuously made grand strides within the industry, resulting in pivotal changes. At the forefront of this transformation is Kimberly Morrison, one of several women who have played pivotal roles in shaping the mining sector.

Aug 1, 2025

By Stephen J. Crittenden

Deep gas and oil production has been substantially increased over prolonged periods through the use of sintered bauxite propping agents. Since its inception in 1976, over 170,000,000 pounds of high strength ceramic proppants have been employed. Recent field evaluations and economic analysis demonstrate the superiority of sintered bauxite proppant over quartz sand. This paper describes the development, application, field results, and product evolution of sintered bauxite.

Jan 1, 1983

By V. Duddempudi, B. Goertz, J. Brune, G. Bogin, F. S. Barreto

"INTRODUCTION In designing a new pneumatic Dust Sampling Device (DSD) for coal mines, it was essential to analyze the air and particle flow inside the device in detail using Computational Fluid Dynamics (CFD) modeling. Several CFD models were developed to simulate the air and dust flow and sample collecting process of the DSD. These CFD models were developed to assist in the design of the DSD instrument prototypes for laboratory testing. Nozzle and injection parameters such as geometry, air velocity and pressure, were varied across a wide range to obtain the optimal settings to accurately simulate the fluid dynamics of the multi-phase flow within the DSD. Accordingly, these parameters were used as a guide for the design of the DSD and to verify the dust scouring dynamics, which is designed to represent the dust entrainment during an actual methane or coal dust explosion. BACKGROUND The 2010 explosion at the Upper Big Branch mine has demonstrated the destructive violence of a coal dust explosion. A major contributing factor for this disaster was that the mine operators did not have a reliable, direct-reading method to collect mine dust and determine inert content and combustibility. This led to the development of a new prototype handheld, pneumatic mine dust sampling device (DSD), which blows a puff of air and entrains the mine dust by mimicking the entrainment process during a mine explosion. A computational Fluid Dynamics (CFD) model is used to analyze the air and dust flow inside the DSD. The objective of the CFD modeling effort is to find the optimum design of the DSD prototype, nozzle orientation, air pressure and pulse length by analyzing and varying these parameters so that the scouring action collects a valid, representative and repeatable mine dust sample. CFD MODEL DESIGN Figure 1 shows a wireframe image of the DSD which is utilized in the setup of the CFD model. The DSD has a triangular cross section and is 10 cm wide. Two nozzles with cross-sectional dimension of 2.8 cm by 0.25 cm act as inlets at the narrow end of the triangular cross section. The CFD model includes a reference plane 6 cm away from the nozzle to measure the quantity of dust collected. The geometry shown in Figure 1 was created for the model and it matches with the design of the actual device shown in the figure 2. Symmetry, along the plane X-Y through the center of the device, is used to reduce the number of computational cells in the CFD model. Figure 2 shows the prototype device used for experimental testing. CFD MODEL SETUP Figure 3 shows a hexahedral mesh with a cell size of 0.8 mm and the total number of cells is around 650,000. The ANSYS Fluent® pressure based solver with a transient case was used with a total duration of 40 ms. The 40 ms simulation time is based on experimental measurements to capture the injection of air and initial scouring of dust."

Jan 1, 2016

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By R. C. Emmett

In extractive metallurgy, separation of insoluble solids from solutions is an important economic factor in almost all flow- sheets. This separation step can employ sedimentation, filtration (vacuum and pressure), or centrifugation. Since practically all systems require a relatively complete separation, multiple unit, countercurrent thickeners or vacuum filters are generally used.

Jan 1, 1974

By Wedam Nyaaba, Samuel Frimpong, Bruno Ayaga Kansake, Irene Akalanyaba Ateng

Haul truck capacities have increased due to their economies of scale in large-scale surface mines. These high-capacity trucks impose dynamic loads on haul roads. A previous study estimated the dynamic forces imposed by ultra-large trucks on haul roads to be more than three times the static load. These dynamic forces exacerbate haul road stresses and deformation. Current haul road response models are 2D and use static truckloads for low-capacity trucks. No models capture the ultra-large truck dynamic effects on haul road structural response. This study uses 3D finite element (FE) modeling to compute the haul road response to ultra-large truck dynamic loading. The dynamic forces were modeled using multibody dynamics (MBD) in MSC.ADAMS. These forces were used in an FE model developed, verified, and validated in ABAQUS, to simulate the response of the haul road to the dynamic truck forces. The road was modeled using an elastoplastic Mohr-Coulomb model. The results showed that road deformation decreases with increasing layer modulus and increases with increasing payload. Increasing the base modulus from 100 MPa to 450 MPa reduced the maximum deformation from 258 mm to 62 mm. When the subbase elastic modulus increased from 100 MPa to 500 MPa, the maximum deformation decreased from 160 mm to 84 mm. Increasing the payload from 0 to 120% of the rated load increased the maximum wearing surface deformation from 131 mm to 216 mm. This study forms a basis for designing structurally competent haul roads for improving haulage efficiency and truck and operator health.

Jan 7, 2023

By H. T. Mulryan

Talc is used as an essential ingredient in a wide variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance, and household furniture components to high performance parts made from liquid crystal engineering resins. The paper focuses on polyolefin applications; the three tier market for talc in polypropylene; the effects of various talcs in typical compounds; and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds which mimic higher cost resins, and polyethylene films, customer requirements for talcs for these purposes are discussed.

Jan 1, 1993

By S. Nygren

Nalco Chemical Company and a North Carolina Phosphate operation have formed a successful supplier/customer team effort that has resulted in major improvements in the operation of the clay thickening circuit at the Aurora, North Carolina concentrator. A Nalco OPTICUS® Automated Process Control System for thickener and flocculant control was installed in 1994. The paper will discuss in detail the development and refinement of the OPTICUS system over the past three years. The paper will survey the development and networking of process control for monitoring, controlling and operating four 325-foot Dorr-Oliver thickeners, three 80-foot high-rate Enviro-Clear thickeners and control links to the facility's clay/gypsum blending operation.

Jan 1, 1998

By The SME Sustainable Development Committee

The evolution of sustainable development in mining is recognized as a key contributor to sustainable development (SD), which is defined as the ability of current generations to meet their needs without compromising the ability of future generations to meet their own needs (Brundtland, 1987). This includes, in equal parts, social, economic and environmental impacts ? triple bottom line (Munashinge and Shearer, 1995). Alternately, sustainability has been defined in relation to social, natural, human, physical and financial capital. Our way of life relies significantly on the materials provided by mining, while mining activity affects the triple bottom-line or the five capitals. The mining community and its professionals have come to realize the importance of engaging all stakeholders in the discussion on sustainability. SME, as the leading professional mining organization, has been involved in these discussions. The society has various initiatives in sustainable development for members and stakeholders. The objective of this article is to: provide historical context for current trends in mining and SD and share SME sustainability initiatives ? their goals and rationales ? with the broader mining community. This article is timely because the past year saw two landmark forums on sustainable development: Rio+20 ? the 20th meeting of the United Nations Conference on Sustainable Development, and MMSD +10, the Mining, Minerals and Sustainable Development project 10 years on. Furthermore, this year marks the 10th anniversary of the Milos Declaration on the minerals professional?s responsibilities in achieving sustainable development, forums in which SME was involved.

May 1, 2013

By J. Kretschmann, K. van de Loo, J. Brune

In 2018, the German Federal government decided to phase-out the energy production using coal-fired power plants and to terminate lignite mining completely by 2038 at the latest. This decision will impact approximately 60,000 jobs. It will have an enormous impact on the socioeconomic development especially in all German lignite mining regions. To avoid economic and political friction, it is of utmost importance to achieve a sustainable transition towards a post-mining era and to offer residents in the mining districts perspectives for a good future that include adequate job opportunities. In this context, the German government is providing massive structural aids early on. As previous closure experiences from the German hard coal mining industry have shown, it takes at least a generation to overcome the effects of a strategic closing decision of this magnitude. Therefore, the planned closure process appears to be a long time at first glance. In fact, however, it is not.

Mar 2, 2022

By A. D. Davis

A ground-water flow model was developed to simulate the post-mining recharge rate at the Belle Ayr surface coal mine in the Powder River Basin near Gillette, Wyoming. State regulations of Wyoming require that reclaimed lands should provide a rate of recharge that approximates the pre-mining rate. Steady-state calibration and transient simulations showed that the post-mining recharge rate in backfill is at least five centimeters per year, exceeding the original infiltration rate of 0.4 centimeters per year to shallow, overburden aquifers. Major reasons for the increase include the flat topography of reclaimed areas and decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate less than five centimeters per year but somewhat greater than the pre-mining rate.

Jan 1, 1995

By Glenn E. Craig

The practical and effective pulp distributor here presented is believed to be of a completely new and innovative design. It was developed at the San Nicolas Plant of the Marcona Mining Company in Peru, where it has been thoroughly plant tested using iron ore slurries of a particularly abrasive nature. It has proven to be superior to the apparatus originally installed, or to any observed in operation elsewhere. In plant practice the capacity and efficiency of many process units such as screens, magnetic separators, and jigs are strongly affected by the loading pattern, and for better results the flow of pulp must be proportioned across the receiving lip in equal quantities per unit width. The distributors originally installed on the drum magnetic separators in San Nicolas proved to be unsatisfactory, and several trial modifications failed to show any improvement. As is usually the case, feed rates were being steadily increased, and appreciable losses to tailings resulted. A check of the distributors on the market discloses no reasonable substitute, so efforts were directed toward devising an entirely new type. Required was a positive type of action which would guarantee that the pulp flow be spread equally along the length of the drum. Discussion As indicated, the motivation for development was simple necessity. The plant in San Nicolas crushes, grinds, and concentrates magnetic iron ores of a particularly abrasive nature, and depends largely on magnetic separation to obtain a marketable product. Feed to the numerous drum magnetic cobbers and finishers varies from rod mill discharge at a nominal minus ten mesh to a ball mill fine grind of seventy percent minus three hundred and twenty-five mesh. Operational factors affecting the magnetic separators were well controlled,

Jan 1, 1971