Search Documents

By Jay S. Silhanek, Vernon E. Andrews

[Introduction] Section 122 of the Clean Air Act Amendments of 1977, Public Law 9595, directed the Administrator of the Environmental Protection Agency, to review all relevant information and determine whether emissions of radioactive pollutants into ambient air will cause or contribute to air pollution which may reasonably be anticipated to endanger public health. In August 1979, EPA published a preliminary report on assessments of public health impact resulting from emissions of radionuclides into air from a broad spectrum of major source categories (1). A section of this document presented a theoretical analysis of the radioactive airborne emissions from several non-uranium mines including iron, copper, zinc, clay, limestone, fluorspar, and phosphate. Since 1978 EPA's Las Vegas Laboratory has been gathering field data on actual radionuclide emissions from these mines to support the earlier theoretical analysis. The purpose of this paper is to present the results of those field measurements in comparison with the assumed values for the theoretical analysis. Data were presented in EPA's preliminary report on both gaseous radon-222 and particulate uranium-238 emissions from non-uranium mines. Most of the emissions data were rough estimates based upon the uranium content of the ore. Preliminary data from a few field studies were also used. Although both the theoretical and field studies by EPA were concerned with radon-222 and radioactive particulate emissions, this paper will concentrate only on the radon effluents. Radon from mines seems to have the greatest potential for possible health effects due to radiation. Data on particulate emissions are presented in other technical reports (2-5). [Theoretical Study] The theoretical emission data are presented in Table I. The estimates for the iron, zinc, and clay mines are based upon preliminary measurements taken by the Las Vegas laboratory. The estimates for the other mines were made assuming that 20% of the total radon-222 in the ore was released during the mining process and the radon release rate from the exposed ore surface was a factor of two greater than that resulting from mining. [ ] Dose assessments for radon from these mines were carried out using model facilities located on generic sites (1). The AIRDOS-II computer code (for estimating dispersion of airborne pollutants) with some minor modifications was used to determine working level exposures to a maximally exposed individual and a regional population. A conversion factor for risk/WL-year(O.021 fatal cancers/person-WL-y) was developed primarily from information on uranium miner exposures (6). This computer code and conversion factor were then applied to the assumed emission rate of radon-222 from each type of mine to develop estimates of working levels, lifetime risks and number of fatal cancers. A summary of this data is presented in table II. [ ] The highest estimated number of cancer deaths per year of operation is 0.05 cancer deaths or 1.0 death due to radon during the 24 year life of a phosphorous mine. For comparison, EPA estimates that underground uranium mines would cause .03 cancer deaths per year of operation in a regional population(1). [Field Study] As a followup to the theoretical study, EPA's Las Vegas laboratory began making measurements in 1978 of actual emissions of radon-222 and radioactive particulates from mine vents at several facilities for each of the industries listed in Table I and II. They were intended to verify general information and radon emissions from EPA's theoretical estimates.

Jan 1, 1981

By Mark Board

INTRODUCTION As the world's supply of near-surface metalliferous ore bodies is depleted, more emphasis must be placed upon mechanized bulk systems of underground mining. In particular, block caving is becoming increasingly important as a method of mining low to moderate grade deposits at depths of somewhat less than 1219 m (4000 ft). 00 ft). The block caving method requires that the ore body be completely undercut, thereby removing its means of support and inducing failure which progresses from the undercut to the ground surface. As the span of the under- cut increases and the weight of the overlying crushed ore body becomes greater, large stresses are induced on slusher and haulage drifts. Stability of these drifts is critical in block caving operations and often proves to be an extremely difficult task (Kendorski, 1976; McWilliams, 1975). Slusher drift maintenance can be costly, often exceeding that of the original support costs. This chapter analyzes the ground support problems of an Arizona block caving mine. The mine presently uses monolithic concrete liners as a support method. Failure of the liners occurs as the undercut approaches, thus initiating a maintenance problem which will continue until the ore body is depleted in that block or panel. To examine this problem, a simple analysis of the stresses induced by the advancing undercut was per- formed. Utilizing a design method developed by Dixon ( 1973, 1974), the calculated stresses were used to deter- mine the minimum thickness required for varying section shapes of unreinforced concrete liners. It is found that the thicknesses required for stable linings are not economic. Recently developed empirical methods of support de- sign are utilized (Barton, 1974; Bieniawski, 1973) and compared to the analytical method. A final discussion of alternative methods of support is given with recommendations for the use of passive or "yielding" support methods. LAKESHORE MINE (GENERAL GEOLOGY) The Lakeshore copper property is located in Pinal County, AZ, approximately 45 km (28 miles) south of Casa Grande. The Lakeshore deposit is a porphyry cop- per similar to others in Arizona. The ore body consists of disseminated chalcopyrite and fracture fillings in quartz monzonite porphyry (QMP), Cretaceous volcanic (KVS), Precambrian diabase, and Mescal limestone. The ore body has been divided into three distinct zones of mineralization which have been termed (South, 1972) the oxide zone, the sulfide zone, and the tactite zone. The oxide zone occurs in the upper portions of the ore body and consists primarily of leached and oxidized quartz monzonite porphyry and Cretaceous sedimentary and volcanic rocks. The sulfide zone underlies the oxide zone and includes all quartz monzonite porphyry and Cretaceous rocks which have not been oxidized. The thickness of the sulfide zone is variable and ranges from about 61 to 122 m (200 to 400 ft). The tactite zone occurs in a series of Paleozoic metasediments consisting of tactite, quartzite, diabase, hornfels, and dikes of quartz monzonite porphyry. The tactite zone is highly variable in thickness and underlies the Cretaceous volcanic and sediments throughout the mine. Together, the tactite and sulfide zones are known as the thick or tall sulfides. The greatest support stability problems occur in mining of the tactite zone and are therefore the subject of the remainder of this chapter. MINING METHOD The Lakeshore mine is a block caving mine utilizing a panel caving method. The present mine consists of two

Jan 1, 1982

By G. Robert Frey

INTRODUCTION This chapter on underground rotary drills briefly describes the equipment features, selection or applica¬tion criteria, safety features, and relative costs of both face and roof drills. After a brief description of the basic components, the application, safety, and cost con¬siderations will be explored. ROTARY DRILL COMPONENTS As illustrated in Fig. 1, an underground rotary drill consists of five basic components. These components are the energy system, chassis, boom, feed assembly, and operator's station. Energy System The energy system of a typical underground drill con¬sists of an electric motor, driving a hydraulic pump or pumps. Usually, the drill is equipped with a cable reel to store the trailing power cable from the portable power center in the mine. A simple control box is supplied to house electrical switchgear and protective devices. In addition to the pump, the hydraulic portion of the energy system includes the hydraulic cylinders, hydraulic tram motors, relief valves, control valves, etc., necessary to actuate the various machine functions. Chassis The chassis provides the frame or support structure for the other four basic components of the drill. Fre¬quently, it incorporates an oil reservoir for the hydraulic system. The chasis provides the support for the trans¬mission, which drives rubber tires or, in the case of some foreign machines, the crawler tracks. The steering link¬age and steering tires also may be considered as parts of the chassis. Boom The boom is the structure that supports the feed assembly; it is either hinged or pivoted on the front of the chassis. Hydraulic cylinders on the boom are used to lift or swing the boom relative to the chassis and to swivel or "roll" the feed assembly. Feed Assembly The feed assembly is made up of the support struc¬ture with an integral thrust mechanism, a rotation unit, centralizers to stabilize the auger, and a hose handling arrangement. In addition, most drills have an extension frame with a tilt device to aid in positioning the feed. Operator's Station The operator's station is the area from which the miner operates the drill. UNDERGROUND ROTARY DRILL APPLICATIONS Underground Face Drills Underground face drills are used in mining opera¬tions that utilize the conventional mining system. The face drill is used to drill holes in the exposed face of the material, and the face is then "shot" by means of explo¬sives or high pressure air. The loose material then is ready for loading and transporting from the face to the preparation plant. Typical specifications for under¬ground face drills are listed in Table 1. Certain parameters should be established as to where the drill is to be used and what is expected of it. To create an awareness of some of the considerations that too often are overlooked, some questions are listed that should be asked in conjunction with the selection or application of the proposed drills. Energy System: Can the drill be supplied with the proper voltage to match the available or proposed elec¬trical power system of the mine? Is the system 250, 460, 500, 550, or 950 v; dc or ac; 3-phase; 60 or 50 Hz? Is the drill equipped with an adequate electric motor to handle the proposed duty cycle? Typical motor power on a single-boom drill would range from 25 to 40 kW (35 to 50 hp); the nominal power for a dual-boom

Jan 1, 1982

High pressure grinding rolls have found widespread acceptance for cement processing, and are now making their debut in the metalliferous minerals industry. Significant energy and wear material savings appear achievable in many applications. This paper re- views the technical literature on this important, emerging technology.

Jan 1, 1997

By P. J. L. Nel

The paper describes several successful concepts used in the sinking of shafts on the Elandsrand Gold Mine. The concepts enabled the shaft sinking time to be reduced as well as the period in which development would normally take place to establish initial ore reserves.

Jan 1, 1981

By B. J. Arnold, B. W. Parker

Rosebud Mining Company added a classifying cyclone/spiral concentrator circuit addition to its McVille Preparation Plant, Freeport, PA, in mid-2002. This paper will describe the plant addition, which was implemented fully by plant staff, and review improvements in cleaning plant performance and economics.

Jan 1, 2003

By P. C. Kapur

For mineral processing spirals, mathematical force equilibrium models are sought to extend the spiral performance envelop. In Part 1 of this report, a complete geometric description of the helical spiral and its trough or channel contour is provided. The secondary circulatory fluid motion in the transverse direction that develops when water flows down a tightly turning curvilinear path and its implications for gravity separation are discussed. Different forces that act on the particle during its passage through the spiral are enumerated and quantified for a better appreciation of their relative contributions and roles in the separation process. Three force equilibrium models from the hydrology literature on sed iment transport are employed to simulate a typical spiral. While the results are promising in that the models mimic the broad performance characteristics of the spiral, what is needed is a more general spiral model taking explicit cognizance of the missing components essential to the spiral description. These are such components as centrifugal force and the steep tangential slope of the channel deck. Results of this latter exercise are deferred to Part 2.

Jan 1, 1996

By J. Kemeny, K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in an area of the mine that contains argillite and is relatively homogeneous. This process also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for argillite will be updated as more tests are conducted, and the model will be extended to the four other primary rock types at the Asarco Mission mine.

Jan 1, 2011

By C. R. Pelley

This paper is intended to describe the utilization of Western subbituminous coal as used in a utility-sized steam generator. It compares this coal's characteristics with those of a typical Midwestern and Eastern coal as a base and reviews the various design considerations when blends of these coals are used. The effects of blending various low-sulfur Western coals with Midwestern or Eastern coals to achieve a predetermined sulfur dioxide emission and the resulting alteration in the coal characteristics as they apply to utilization are also reviewed. The blending of coals as one means of complying with sulfur dioxide regulations will take on increasing importance as the various deadlines for compliance with new and existing regulations approach. We must first consider the availability of these low-sulfur coals; and insofar as the Eastern low-sulfur coals have been mined for many years, we have focused our attention on the availability of the coal reserves west of the Mississippi River in the United States, as this is the area to which many people are turning in order to meet this requirement.

Jan 1, 1976

By Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky, and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought, but rather 20° in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Jan 1, 1997

By James J. Scott

Longwall mining has not received a great deal of attention in the United States; however, this system offers many advantages over the conventional room-and-pillar methods now being used. In order to conserve the coal resources of this country, the U. S. Bureau of Mines has investi¬gated the feasibility of adapting European longwall mining methods to American coal seams. Their studies showed longwall mining to be well suited to thinner seams and, greater depths; and, in addition, permitted almost 100 percent recovery of the coal. Most, experiments with this method resulted in higher overall production-costs than were commonly obtained with highly mechanized room-and-pillar techniques This high cost-was largely due to the excessive amount of labor required to maintain adequate roof support with conventional longwall mining techniques. With the substitution of hydraulic-powered, self-advancing roof support systems for conventional supports, this excessive labor cost has been decreased, and longwall mining costs are now competitive with those of modern room-and-pillar mining.

Jan 1, 1964

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By Ross Glanville

The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR cam also be expressed as the Optimum Mime Life (OML) in years since the expected mime life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mime life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mime life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low¬-tonnage mines (such as many underground gold/silver deposits) often lead to sub¬optimal results. In fact, am apparently uneconomic deposit at am arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mime' properties based on arbitrary production rates.

Jan 1, 1984

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited amount of studies have been conducted that characterize hydrologic changes and also quant1fythe magnitude of mining-induced subsidence. The U.S. Bureau of Mines conducted such a study at a mine site located in Greene County, PA. A total of 8 water wells were drilled and hydrologic parameters such as specific capacity, transmissivity and well yield were determined both before and after mining. Electronic water level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1990

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

  Underground positioning and communication are essential technologies for the future of underground mining operations. In contrast to other positioning and communication technologies such as wireless local area network (WLAN) or radio frequency identification (RFID), ultra-wideband (UWB) radio technology provides significant benefits like accurate and robust positioning of mobile machine equipment, which is indispensable for future autonomous systems in underground mining processes, such as production, transportation and auxiliary operations. Among these technologies, UWB offers many advantages, including higher accuracy, robustness, resistance against noise and multipath effects, and low power consumption [1,2]. Underground automation and localization systems benefit from these advantages and use the technology to improve efficiency and safety. There are many studies being carried out on this technology to increase the results’ accuracy, energy sufficiency and more. Two robust UWB modules that were developed for underground positioning and collision avoidance with regard to human safety in underground mining operations are introduced. The measurement results of tests carried out in an underground mine are discussed as well to confirm the functionality of the system.

By Kent D. Gastreich

As the number of prime surface coal mining sites diminishes with time and with the potential for increased coal demand, areas that were previously not mined because of their difficult mining conditions, marginal economics, and controversial environmental nature, will have to be considered if surface coal mining is to continue in the future. Such sites include areas near major rivers, streams, and lakes. The name most commonly given to these areas by regulatory agencies is "wetlands". The exact definition(s) to the term "wetland" will be discussed later in this paper. Most coal operators are now more than familiar with permitting requirements under the Surface Mining Control and Reclamation Act of 1977 (SMCRA). The SMCRA permanent regulatory program recognizes the fact that coal mining operations will periodically encounter streams, wetlands, etc. Although discussed in various sections of the permanent program regulations, the relationship of coal mining operations to wetlands is particularly evident in the performance standards regarding hydrologic balance and protection of fish, wildlife and related environmental values.

Jan 1, 1980

By J. M. Hird

By blending phosphogypsum with thickened mill clays, Texasgulf has successfully resolved the problems of gypsum disposal and reclamation of mined-over areas. In the process, clays are thickened to 10% solids through high rate thickeners, mixed with gypsum from a drained gypsum pile (75%) and a direct discharge from belt filters (25%), then pumped to mined-over areas. The blending of clays and the low pH gypsum yield a mixture with a pH of about 7. Dewatering is rapid to 40-45% solids within 3 months. The material spreads with very shallow slopes and within a year desiccation by high flotation ditching equipment is possible. The artificial soil is classified as a silty loam in texture, lacking only in nitrogenous nutrients. The soil material has proven to support many field crops including small grain, corn, alfalfa, and grasses. Sycamore, green ash, sweetgum and bald cypress have done well in 3 years of growth. The nitrogen source for tree growth will be made up through an alfalfa cover.

Jan 1, 1993

By Thomas E. Garnar

Mineral sand products have been produced from beach sand heavy minerals for nearly a century. These minerals have specific gravities of 3.0 or higher and are extremely resistant to weathering. The most common economic heavy minerals are ilmenite, leucoxene, rutile, zircon, stauarolite, monazite, garnet, and the aluminum-silicate minerals. Of these, ilmenite is the most abundant. In some cases a deposit may contain only one or two economic heavy minerals whereas in others five or six may be present. Heavy mineral mining began in the late eighteen hundreds when monazite was mined for its thorium content. This was followed by mining activity on the North Florida coast just south of Jacksonville Beach - where ilmenite and zircon were first separated during the WW I (1,8). Modern heavy mineral mining began in Eastern Australia during the late nineteen-thirties and spread to the United States during World War II. It is the purpose of this paper to review the commercial heavy mineral products, their sources, and their uses.

Jan 1, 1985

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990