Search Documents

By G. G. O. O. Uwadiale, M. A. U. Nwoke

The recovery of iron from low-grade (31.6% Fe) Muro iron ore was investigated using reverse anionic flotation of quartz. Tests were performed to investigate the effect of pH, the effects of using distilled vs. tap water as the flotation medium and the effects of using cassava starch vs. dextrin for the depression of iron minerals. The optimum results were obtained around pH 10 and 11, and cassava starch was superior to dextrin in depressing iron oxides. Investigations at pH 11 using cassava starch and distilled water resulted in a concentrate grade of 69.4% Fe with a recovery of 84.4% Fe. Under the same conditions, the use o f dextrin produced a concentrate grade q f 65.9% Fe with a recovery of 78.6% Fe. Investigations at pH 10 using cassava starch and distilled water resulted in a concentrate grade of 60.2% Fe with a recovery of 83.9% Fe, and under these conditions the use of dextrin produced a concentrate grade of 56.1 % Fe with a recovery of 81.5% Fe. Flotation studies conducted at pH 11 using tap water and cassava starch resulted in a concentrate grade of 70.4% Fe with a recovery of 92.7% Fe. This demonstrated the superiority of tap water over distilled water in the reverse anionic flotation process. Investigating the effect of calcium ions on the activation and flotation of quartz with oleic acid revealed that a calcium ion concentration of 50 to 100 ppm was optimum.

Jan 1, 1996

By David M. Mchaina, Allan E. Hall, W. C. H. Kruining, Alan Coode, Stephen Hardcastle

This paper details an investigation into the feasibility of recirculating mine exhaust air in Saskatchewan potash mines. This project was initiated following a previous study at Ruttan Mine, Manitoba, which indicated that recirculation of exhaust air to reduce winter heating costs was feasible. The potash industry was selected for study because the mines use a minimum of blasting in their production methods and the exhaust temperature is significantly higher than that of most metal mines. These factors simplify the monitoring system required and have the potential for greater waste heat recovery. A series of measurements of underground mine pollutants was made at the main exhaust and intake shafts in order to determine the feasibility of introducing controlled recirculation of exhaust air. An experimental recirculation circuit was created by opening two existing doors situated between the return and intake shafts. During this recirculation trial, the air quality parameters at the intake, mixed intake and exhaust measuring stations were monitored. The results obtained from a questionnaire circulated to the regulatory agency and the major potash producers together with results obtained from underground field studies at Central Canada Potash (CCP) Division of Noranda Minerals indicated that controlled recirculation of mine exhaust air has potential application in these mines either to reduce heating costs and/ or to increase the face air quantities. A recirculation system is to be designed in conjunction with CCP and the Saskatchewan Ministry of Labour, Mine Safety Unit to attempt to implement a working recirculation system for CCP.

Jan 1, 1989

By Timothy P. Smirnoff, Arthur P. Chase, Herman J. Smith

INTRODUCTION The Newtown Creek Pollution Control Project (P.W. 53) is a major system of facilities designed to collect wastewater from large areas of the Boroughs of Manhattan, Brooklyn and Queens, then channel it to a treatment plant where the wastewater is processed and discharged. The North Branch interceptor collects wastewater along the east side of Manhattan and transports it downstream to a Junction Chamber at Avenue "D" near East 13th Street. The South Branch interceptor similarly collects wastewater from the southern part of Manhattan Island on both east and west sides of Manhattan and transports it to the same Junction Chamber from where both flows are delivered to the adjacent Manhattan Pumping Station which pumps the wastewater under the East River to a treatment plant in Brooklyn. This system is shown in Figure 1. Construction of the Manhattan Pumping Station began in the Summer of 1966 and was delayed by a number of mishaps. In the vicinity of the North and South Interceptors, approximately 3,060 cubic meters (4,000 cubic yards) of soil flowed into the excavation: 765 cubic meters (1,000 cubic yards) at the North Branch Interceptor, and approximately 2,300 cubic meters (3,000 cubic yards) at the South Interceptor. These movements were accompanied by surface subsidence, collapse, or both. On June 4, 1973, while pumping station construction was underway, approximately five to seven cubic yards of sand entered the junction chamber through a temporary bulkhead valve in the North Branch Interceptor.

Jan 1, 1979

By Ora H. Rostad

The sequence of events preceeding the discovery of the Mount Emmons molybdenite include some inadvertent near misses by several groups. The events are given in general chronological order to bring out the essentially contemporaneous, but different activities by several groups in two areas on opposite sides of Mount Emmons. The Mount Emmons molybdenite deposit lies in the Elk Mountain mining district. The west edge of the deposit is near the boundary between the Elk Mountain and Ruby mining districts as shown by the USGS map included (see Fig. 1). Considerable history regarding the Keystone silver-lead-zinc mine is given because of its proximity to the Mount Emmons molybdenite deposit which is on the other side of the mountain from Redwell Basin and where other significant activities took place. It should be noted that there was no documentary evidence available to me that would indicate that molybdenite was recognized to be present on, or under, any part of Mount Emmons, including Redwell Basin, before 1970. Veins containing silver-lead-zinc minerals were discovered in the Elk Mountain and Ruby mining districts about 1872. Some discoveries on the south flank of Mount Emmons about 1880 were developed into the Keystone mine. The Keystone has the largest cumulative production of metal ores of any of the mines in these districts. Most of the 413 Mt (455,473 st) of ore produced from the Keystone mine through August 1967 was produced after 1950. The ore averaged 175.4 gt (5.64 oz per ton) Ag, 2.62% Pb, 5.56% Zn, and 0.72% Cu.

Jan 1, 1991

By A. E. Ketler

Powerful, yet inexpensive, personal computers running Windows-95 operating systems provide powerful mine-wide monitoring capabilities when properly engineered. Long awaited conductivity over LAN, phone and Internet links provide new dimensions for sharing information throughout an operator's organization, in- deed around the world. On-line data analysis, archival data storage and historical trend viewing generate shared inputs to production, safety and maintenance personnel. Five years in development, Rel-Tek's new EZ-Trol/W-DX system was engineered around the pilfalls of a Windows environment. It now offers higher speeds, 3D animated graphics and long distance telemetry - all with better reliability than ever before possible. The ubiquitous DDS utility inherent in most Windows was discarded in favor of a lightning fast RAM format. Several ponderous interpretive programs were redesigned into a single compiled entity, thus avoiding the overhead from message conversion, handshaking and transfer. To make the system user friendly, a 'Wizard" utility helps operators set up and reconfigure their systems on site. In-mine data acquisition telemetry was also re- vamped, incorporating a unique noise avoidance scheme, dubbed the "DX" bus - enabling longer distances and higher reliability. 12- bit analog conversion provides the enhanced resolution needed for field scaling auto-cal sensors. By mid '96, eight EZ-TROLMI- DX systems were up and running, several for more than a year. Factory updating and assistance are possible over a phone or Internet link. Our factory testing of components routinely includes actual operation at 2400 BAUD over 14 miles of twisted pair wires.

Jan 1, 1997

By A. L. Boerner

Off-highway tire costs represent a significant portion of the total mining costs in openpit, truck-shovel operations. To extend the lives of tires, the site-specific factors influencing tire life should be investigated Valuable data can be obtained by combining historical operational data captured by a mine dispatch system with detailed tire and maintenance histories. Assuming that failure counts satisfy a Poisson distribution, F-tests can be applied to determine significant deviations from desired or target counts. The methodology developed in this paper can be used to identify the haul routes and loading and dumping zones that have significantly higher incidences of tire failure. Corrective action can then be targeted at these zones by modifying the shovel or truck operator practices; changing the haul route maintenance and clean up practices; or altering the bench, ramp or waste dump design parameters. An example is given of the correlation of tire separation and tire impact failures with haul routes for a fleet of nine Caterpillar 793C trucks in operation at the Chuquicamata Mine in northern Chile. A high incidence of impact failures was observed for the ex pit ore crusher and for tires installed in the left outer rear position on the trucks. The latter was postulated to be due to a preference for drivers to execute right-hand turns prior to dumping. Recommendations were made to revise crusher and dump cleanup practices and investigate the feasibility of super-elevating the surface of dumping zones to reduce ground pressure on the left rear tires.

Jan 1, 2002

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By J. D. Miller, C. L. Lin

As the techniques and resolution for three-dimensional spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional X-ray microtomography offers a unique imaging capability. Spatial resolution on the order of 10 µm can be achieved with the use of microfocus X-ray generators. Recently, a state-of-the-art cone beam X-ray microtomography system was installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility was designed to obtain 2,048 by 2,048-pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind instrument can be used to obtain three-dimensional spatial reconstruction for many applications, such as three-dimensional liberation analysis, pore structure analysis of particle beds during filtration and the air-void system of concrete structures. The utilization of X-ray microtomography not only allows for the quantitative analysis of multiphase systems but also allows, for the textural characterization and determination of phase continuity. This paper presents information regarding the current use of this new facility and a review of potential applications for the advanced analytical system. Key words: Cone beam X-ray microtomography, Three-dimensional analysis, Material characterization

Jan 1, 2003

By Donald J. Olson, Thomas J. Lutzenberger, John Ramage

The North Shore Inline Interceptor, Phase IA tunnel is a 8,550-meter (28,000-ft) interceptor tunnel currently being constructed by Traylor Bros./Frontier-Kemper, Joint Venture, using a 9.8-meter (32-ft - 4-in) diameter Robbins tunnel boring machine (TBM). This tunnel is being driven in Silurian age dolomite approximately 91.5 m (300 ft) below ground surface. Significant water inflows were encountered when the tunnel drive penetrated the thinly-bedded Waubakee Formation. Flow increases approaching 0.75 cu m per min per 30 m of tunnel (200 gpm per 100 ft) have occurred in this formation. After driving approximately 2,285 m (7,500 ft) of tunnel (200 m full face in the Waubakee Formation), total flows exceeded 12 cu m per min (3,200 gpm) with about 5.7 cu m per min (1,500 gpm) entering the tun¬nel from the 200 m (600 ft) of exposed Waubakee Formation. Additional water control measures consisting of increased pumping capacity, increased water treatment capacity, surface grouting ahead of the tunnel, grouting ahead of the tunnel face and panning to improve the working environment for installation of tunnel support, were implemented to deal with the large water inflows. Currently (January 24, 1989), 3,400 m (11,000 ft) of tunnel has been driven, total water inflows are in the range of 11.7 cu m per min (3,100 gpm) with only 6.8 cu m per min (1,800 gpm) inflow from about 1,220 m (4,000 ft) of tunnel driven full face through the Waubakee Formation.

Jan 1, 1989

By Eung Ha Cho, Olufemi Olajide

A laboratory study of dense-medium cycloning with Redstone seam coal has been conducted. The investigation was performed using a 203 mm (8 inch) Heyl-Patterson dense-medium cyclone. Two underflow orifices of 31.8 mm (1.25 inch) and 44.5 mm (1.75 inch) in diam were used. The effects of feed pressure and particle size were determined on the cycloning performance. In addition, the cyclone performances with coal-rich and refuse-rich samples were also investigated. The results of the experiments were analyzed using basic hydrodynamic principles. The increase in the feed pressure increases the specific gravity of separation (defined as the specific gravity of a particle which has an equal chance of reporting to either the overflow or underfow) for both underfow orifices. The specific gravity of separation increases as the particle size decreases with the smaller underflow orifice. However, an opposite relationship has been observed with the larger under flow orifice. The separation becomes sharper with the smaller under flow orifice than with the larger underflow orifice especially for fine material. Also, the separation becomes sharper with an increased feed pressure for a coal-rich sample. However, this effect is less significant for a refuse-rich sample. This means that a high feed pressure is required for a coal-rich sample to maintain a good separation. It also means that applying a high feed pressure provides a good separation regardless of the type of feed coal in terms of ash content in the solid.

Jan 1, 1990

By M. H. Kahn, F. C. Bond, K. J. Edmiston

Comminution of various materials can be achieved in grinding equipment by nipping, impact, attrition, or a combination of these actions. Pna mills also known as edgerunners, chasers, and mullers-are classified as a nipping machine. The essential features of this type of grinding machine are rollers or mullers that turn on a horizontal axis while rating on the bed of material in the pan. Ploughs are used to direct the unground material to the center of the pan. Grinding may be accomplished wet or dry. Aritres, Chilean mills, and Huntington mills are types of pan mills. Ring roll and ring Ml mills, another type of nipping machine, were developed for grinding smaller particles of intermediate hardness to product sizes of about 100 pm. They were designed to attempt to reduce the cost of similar size reduction in ball mills and have been widely used to pulverize coal for power-plant facilities. Impact Machines Grinding machines that can be classified as impact mills include: hammer, cage, centrifugal, vibratory, pin, and stamp mills. The distinctive feature of an impact mill is that it has a fast-moving part that transfers some of its kinetic energy to the material particles by direct contact so that internal stresses are created in the particles. The Reitz Disintegrator is an example of an impact mill. It has rigidly mounted hammers attached to a vertical shaft that rotates in close proximity to horizontally mounted screens. The feed pulp enters parallel to the vertical shaft, and may have a solids content of from 40

Jan 1, 1985

By L. Whitby-Costescu

The Shebandowan mine and concentrator, with a capacity of 9072 t/week (10,000 st per week), was opened in 1972 after several years of environmental study and planning. The mine is located in a popular vacation cottage .area about 96 km (60 miles) west of Thunder Bay, Ontario. Undertaken before environmental assessment procedures had become an established requirement, Shebandowan is one of the first Canadian examples of effectively integrating environmental work into overall planning. Although it is an underground mine, many of the environmental considerations are common to open-pit operations, and hence, it provides a case history for the use of all mine planners. Computers can play a part in such studies by simulating the annual production of mine wastes, by on-line polling of environmental sensors and by processing sensor data. Early attention was focused on establishing base-line conditions in a two-year water quality monitoring program. Since production began, water quality monitoring has shown that mining has not caused any significant changes. However, mine drainage disposal arrangements had to be modified in the light of operating experience. There is no townsite associated with the mine, and workers commute from established municipalities. Harmonious relations have been achieved with local cottage residents after their initial fears were dispelled. Plans are ready to begin revegetating the tailings when a sufficient area of dry elevated tailings has been accumulated. Rehabilitation of the land disturbed during development was begun before start-up and was completed during initial operations.

Jan 1, 1979

By R. Owen

An overwhelming amount of data can be collected around the blasting process. This information can include blasting product, pattern design, blast results, and routing. It is only when these data sources are combined in a concise and accurate form that they are of real use in determining the safety and economic implications of each parameter. Two key technological aspects of blasting are drill fleet management (DFM) and size fraction analysis (SFA). As these technologies are integrated as near-real-time measurement and QA/QC tools, the resolution and realization of blasting parameters is significantly increased. The Freeport-McMoRan Morenci Mine has integrated these technologies along with other existing database structures to create a responsive and sustainable tool for reconciliation, forecasting and parameter matching. This ability allows Morenci to customize blast patterns to meet the criteria most critical to each shot, whether the impact is influenced by routing and recovery, equipment maintenance or safety concerns. DRILL FLEET MANAGEMENT The current DFM was stabilized in its current form in mid 2009 after database and hardware maintenance met stability requirements. Currently the system is running on 12 production drills. The system receives pattern layout and is capable of semi-autonomous drilling over the entire district. The fleet is capable of drilling in highly altered intrusive units and hard granites through the range of sedimentary and volcanic units that comprise the Morenci District. The system brings a level of accuracy not achievable with earlier paint-marked patterns. Depth control is also increased along with more consistent wear and maintenance patterns due to semi-autonomous drilling.

Jan 1, 2011

By C. Otto Walls

Six years after the start of gold heap leaching at Smoky Valley Mining, Round Mountain, Nevada, three areas of process improvements are examined to show how productivity was increased. Original design concepts and practices are reviewed in order to compare to current methods. The evolution of change in heap mainterance is also reviewed.

Jan 1, 1984

By Lennart Mukka

This paper describes the experiences from construction of a new ventilation system in LKABs Kiruna Mine in Sweden as well as the choice of the method for air flow regulation with concern of life cycle cost and the description of the foundation design. The evaluation of the performance test will be presented.

Jan 1, 1997

By None None

This month, Mining, Metallurgy & Exploration (MME) is launching with a special issue on mineral and metallurgical processing in honor of the 90th birthday of Prof. Emeritus Douglas W. Fuerstenau. Headed by a special review article by Prof. Fuerstenau, this special issue contains 22 papers by the top experts in the field.

By W. Roggenthen, Z. J. Hladysz, G. D. Callahan, W. G. Pariseau, W. Weinig, C. Randolph-Loar, R. Popielak

A Deep Underground Science and Engineering Laboratory (DUSEL) is being planned at the site of the former Homestake Gold Mine in Lead, SD, under the sponsorship of the U.S. National Science Foundation (NSF) in cooperation with the Department of Energy (DOE). This national facility will host a variety of multidisciplinary science and engineering experiments, including physics experiments that require shielding from cosmogenic radiation. Current plans include construction of large rooms (up to 55 m in width) at depths of 1.48 km (4,850 ft) and 2.25 km (7,400 ft) below the surface. Preparation of the preliminary design required the development of a geotechnical characterization program, including preliminary drilling and coring, core logging, drill hole mapping with a televiewer, drift mapping of the geology and rock structure, in situ stress measurements, and laboratory testing of the mechanical properties of the rocks and discontinuities. Overall rock quality is very good to excellent. Site investigations included geotechnical assessments for the construction of caverns and laboratory modules. The results are favorable and reaffirm selection of the Homestake site for establishment of a Deep Underground Engineering and Science Laboratory.

Jan 1, 2011

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remotecontrolled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures.

Jan 1, 2016

By K. Luxbacher, A. Haghighat, B. Lattimer

Mine face ignition due to high levels of methane is one of the most common fire incidents in underground coal mines. In continuous miner headings, depending on the magnitude of the ignition or resulting fire, auxiliary ventilation controls may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to an exhausting ventilation curtain in a continuous miner heading, and the impact on ventilation to the face. The computational fluid dynamics software Fire Dynamics Simulator (FDS) Version 6.0 was used to predict the conditions that develop due to a 200-kW fire in the face following a methane ignition with different levels of assumed ventilation curtain damage. Smoke layer depth, temperature and mass flow inby the last open crosscut were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed curtain. As more of the ventilation curtain was damaged, smoke depth and temperature outby the fire increased. With the full removal of the curtain, the smoke accumulated from the last open crosscut to the face, with the ventilation completely bypassing the continuous miner region.

Jan 1, 2016

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized, utilizing waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empiric testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicates that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate when compared to that of conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

Sep 23, 2021