Search Documents

By Felipe Calizaya, Sekhar Bhattacharyya

Mechanized underground mines suffer from noise overexposure. Noise levels are often above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach up to 121 A-weighted decibels (dB(A)), especially when fans are not equipped with silencers. Use of silencers seldom ensures PEL. Overexposure of noise induces permanent hearing loss among mine workers. A NIOSH-funded research project and field studies at six coal and non-coal mines revalidated the findings. The University of Utah undertook laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material was designed and tested. The silencer and associated extension can be repacked with different dampening materials. The silencer and the extension were used in various configurations. Attempts were also made to simulate field conditions. The tests demonstrated a maximum sound level attenuation of about 14 dB(A) at the fan discharge. A properly designed silencer offers lesser resistance and thereby better fan performance and lower energy cost. The re-packable silencer is more likely to be maintained properly. Lowering of noise level happens in audible frequencies (4000 to 8000 Hz) which are important in A-weighting.

By Caibin Wu, Chengfang Yuan, Jiaqi Tong, Zhilong Cheng, Ningning Liao, Chong Zeng

In a series of Julius Kruttschnitt size-dependent breakage models, the cumulative percentage passing 1/10 of the initial size is used as a fineness indicator for scientific research and the selection of grinding equipment. However, in industrial practice, it is quite customary to use the mass percentage passing 75 μm as the indicator. In this paper, based on the energy-particle size model, quartz and calcite, two materials with distinctly different hardness, were used as test samples in a conical ball mill. At the same specific energy, the value of the cumulative percentage passing 1/10 of the initial size decreased while that of the mass percentage passing 75 μm increased with finer feed size. The experimental test values of the mass percentage passing 75 μm have a good linear relationship with the model predictions, which suggests that the particle size energy relationship of the mass percentage passing 75 μm and Ecs can be used instead of the cumulative percentage passing 1/10 of the initial size and Ecs. By building family curves, when particle size x < 300 μm, the family curve can be well fitted, and the fine particle size distribution of the whole product can be reconstructed.

Dec 22, 2022

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley&apos;s molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984

By T. Lee

Ongoing economic success for mining companies is dramatically enhanced when they really know what they are harvesting, such that they can accurately forecast their head grades for any time period in excess of a month. This is an uncommon experience. It is a very common scenario for resource/reserve estimates to overstate the concentration (grade). Grade is a critical input of revenue, and hence, it is to cashflow projections. With the current direction being taken by the legal climate, it is no longer adequate for directors to accept the resource/reserve estimates of experts at face value. This is because resource/reserve estimates are the foundation of primary mineral economic decisions. Directors of mining assets need to undertake their own due diligence analysis of these estimates, in the best interest of themselves, and the company&apos;s shareholders. In the light of the industry&apos;s past achievements, this is quite a challenge. This paper suggests a set of new objective tools for directors to undertake an overview of the unique commodity concentration pattern and assess associated economic dynamics of each mineralization. These tools allow the examination of global graphical trends that can be helpful to directors and others in undertaking due diligence of resource/reserve statements. Ensure that it smells right.

Jan 1, 1995

By Solomon J. Salat

During the major expansion of the Inspiration smelter, which took place in 1973, the bulk material handling system underwent a matching expansion in order to move the required materials. Inspiration is the first smelter worldwide to employ electric smelting in conjunction with the use of Hoboken converters (1), (2). The installation includes a 51 -MVA electric furnace, five 4.25m (14-foot) diameter Hoboken converters, rotary dryer, bedding plant, acid plant, heat recovery steam plant, and gas and dust handling system. See Figure 1, Plot Plan. As of today, the 51-MVA electric furnace is the world&apos;s largest in the smelting of copper. Engineering design for the installation was per- formed by Treadwell Corporation of New York. The task of designing the conveyor system was complex because the system had to be installed while the smelter was operating and with minimum plant shutdowns, and it had to serve both the existing and the new smelter. Existing conveyors were redesigned where necessary and incorporated into the new conveyor system. See Figure 2, Flow Sheet. The system encompasses the handling of such diverse materials as wet and dry copper concentrates, cement copper, silica flux, cold dope, and concentrate and flue dust.

Jan 1, 1979

By B. Y. Wong

In April 1989, Southern Company Services signed a 3.5 year contract with DOE-PETC for generic engineering development of an advanced physical fine coal cleaning technology known as selective agglomeration. This technology offers the potential for significantly higher pyritic sulfur removal (90% +) than conventional coal cleaning (30 to 50%) while maintaining high Btu recovery (90% +). Engineering development will include bench-scale process development; component development; adaption or modification of existing unit operations; proof-of-concept (POC) module design, fabrication, testing and evaluation; and small commercial facility conceptual design. The information obtained during POC operation will be sufficient to result in a technical and economic design base that can support construction and operation of a small commercial plant. The major goal of the research is to develop selective agglomeration technology to achieve 90% pyritic sulfur removal while operating at Btu recoveries above 90% based on run-of-mine quality coal. This objective will be accomplished in two phases: Phase 1 -bench-scale and component development, and Phase 2 -POC module operation and conceptual design of a small commercial plant. Currently, work is proceeding under Phase 1 (Tasks 1-7) of the project. A review of the status of Tasks 1-7 is presented in this paper.

Jan 1, 1991

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of individual particles, which differs for different species of mineral. When a mixture of fine material is exposed to a radiant energy source, the various solids components present in the mixture will absorb heat energy depending on their composition and there will be difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz of 6 x18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Mar 2, 2022

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By Reed S. C. Rogers

There is recent evidence that high frequency screening can be a viable alternative to hydrocyclone classification for a wide variety of grinding applications. However, since high frequency screening is a relatively new development, the decision to use screens generally must be based on full scale screening tests of a slurry material of interest. In this paper the authors employ mathematical simulation models as an aid to evaluating the use of screens versus hydrocyclones for closed circuit fine grinding. This approach is validated in a pilot plant study and then demonstrated for the design of full-scale grinding circuit, including classifier cost comparisons. For the case of maximum production rates versus product size, without a constraint on fine product solids densities, results indicate that screening with Derrick sandwich type cloths can give higher grinding circuit production rates with more narrowly sized products than when hydrocyclones are used. These results are explained in terms of the bypass and Sharpness Index of the respective classifier partition curves. Classifier cost comparisons for the full scale circuit show that although the installed cost of screens is substantially higher than equivalent capacity hydrocylone operations, even modest increases in circuit capacity caused by screens; can significantly reduce total grinding costs.

Jan 1, 1985

By III Boxley

Most of us realize that our nation&apos;s roadways are under ever-increasing stresses, from higher traffic counts to increased tire pressures and their resulting loads. At a time when the interstate system as originally envisioned is completed, and the National Highway System is being drawn to replace it, it is appropriate that we examine design and construction methods for the next century. The stone industry shares a common desire to produce high quality, cost-effective roadways that perform over time. The superior sub-grade and road base structure provides for the superior roadway. Since I am neither an engineer nor a contractor, I will not attempt to suggest design or construction methods. What I can do is share my company&apos;s experience in supplying road base materials by using a historical perspective in Virginia and some trends in the market that we have observed. Road building and related non-building construction are still far and away our largest markets as an industry. If we can help to improve the end product of our biggest customers, we add value to our own product. Indeed, in a time of budget constraints and competing demands for government dollars, we must show value over the life of a pavement structure to ensure their long-term funding.

Jan 1, 1996

By Jon C. Jenkins

In order to plan the most efficient mine installation, a company should take advantage of all available information and tools. One of the first factors of a coal reserve that needs to be determined as accurately as possible is the quality of coal the mine will have access to during the life of the installation. With the aid of many types of well logs and computor analysis, we are investigating several methods of log correlation to determine such data as moisture, ash, sulphur, and BTU on an in place basis. It may be possible to determine this data more accurately in this manner than by using diamond drill cores for analysis and thus allow for a more profitable mine installation. The production of an underground mine is based on many factors, two of these being roof control and line water, where present either in the roof or coal seam. Using many of the same logs obtained from reserve and active mine areas, we have attempted to determine roof and floor characteristics such as strength, lithology, and moisture properties. Using data obtained from this program, we will make comments on possible length of bolt to be used, possible mining width, and pillar size as they would pertain to these reserves and active mine areas.

Jan 1, 1969

By Edward T. Koch

With the dramatic increase in world demand for basic raw materials, open pit mining is proceeding at an unprecedented rate. A viable demand is the ever tempting Siren&apos;s song for increased production or new facilities. When the Siren&apos;s lure is viewed against the panorama of today&apos;s world economic milieu the concomitant Scylla and Charybdis are seen in the form of high capital cost and high operating cost. If the economic realities of present day open pit mining are to show a proper return on investment, a clear and penetrating eye must be cast upon the area of mine planning. This paper deals with the problem of overburden removal. In almost every open pit mining operation overburden removal is a significant part of the capital cost and operating cost of the total operation. This paper deals with a new and unique method to affect economical overburden removal. Well known to all are the parameters surrounding draglines, shovels, and bucket wheel excavators. All of these machines require a reasonably stable soil to support them and the shovel and bucket wheel excavator require a reasonably stable bank in which to operate. Their reliability, portability and rate of production per dollar of invested capital are good.

Jan 1, 1975

By C. G. Cunningham

The Marysvale volcanic field of west-central Utah contains large areas of argillically altered rocks (fig. 1) that, in turn, enclose smaller areas of fine-grained, medium-grade, replacement alunite deposits and coarsely crystalline, high-grade vein-type alunite deposits. The largest replacement alunite deposits are [ ] located peripheral to a 23-m.y.-old monzonite stock called the Central Intrusive (fig. 1). The deposits formed in near-surface, highly oxidizing environments at the tops of hydrothermal plumes that were spaced irregularly around the stock. The deposits are horizontally zoned from alunitic cores through kaolinitic to propylitic envelopes. Vertically, characteristic alteration minerals progress from a pyrite-propylitic alteration assemblage at the base, upward through alunitic, jarositic, and hematitic assemblages to a flooded silica cap as shown on figure 2. The silica caps are cut by hydrothermal explosion breccias. d34Sso4 values of + 11.5 to + 15.4 permil indicate that sulfur in the hydrothermal plume was derived from underlying Mesozoic evaporites. The sharp upward transition from pyrite- propylite to alunite probably marks the paleowater table, and the top of the flooded silica cap represents the paleoground surface. Basin-Range extensional tectonism began shortly after alteration, and buried the replacement alunite deposits in basins beneath sediments eroded from uplands. The deposits were only recently exhumed.

Jan 1, 2013

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By William J. Bryson

Just picture, if you will, the hot, lonely and desolate Ochre Mountains west of Salt Lake City. There works a grizzled old miner, his boots worn down, his clothes hang on a body stooped by years of hard labor. His skin is wrinkled and leather toughened by many years in the hot desert sun. His ever faithful burro stands patiently in the shade of a large rock as the tired old miner examines ore samples just acquired that very morning. Suddenly the old man&apos;s eyes widen, his breathing becomes rapid. &apos;Leaping to his feet, with a gleam in his eye, he cries, "Eureka, I&apos;m rich, I&apos;ve found the mother lode. This is where I will start my digging. " Without warning, the silent wilderness is alive with wild, shouting, charging figures! Frightened the old miner glances about him wide-eyed and pan- icky. His heart sinks, dismayed he now knows all is lost, this is the end. For there leaping from behind rocks and brush papers in hand, are the men from the Department of Interior, Bureau of Land Management, State Mine Inspectors, OSHA, MESA, EPA, OEO, and the never ending list of regulatory bodies related to todays mining industry.

Jan 1, 1975

By J. D. McAuliffe

The Homer-Wauseca Mine is operated by the Hanna Mining Company, three miles north of Iron River, Michigan on the Menominee Iron Range. The mine produces 5,300 tons of direct shipping iron ore daily. The present main producing level is at a depth of 1,500 feet below the collar. The ore body continues to a depth of 2,700 feet below the collar, to which depth the modern circular concrete shaft has been completed. A view of the property is shown in Figure #1. This paper is a report on the development of large underground boreholes used initially to conduct stope filling material into inaccessible, mined-out stopes. Later holes were drilled for ventilation raises, for mine drainage, for passageway for power cable, also for the primary breaking point for long hole stoping. Some, which were drilled as ventilation raises, were later stripped to a suitable size for a manway or ladder road. The holes varied in size from 6" to 30" with the present popular, economical working size being 16 1/4", used as a stope fill passage in mined out areas and for ventilation in deeper development. Foremost has been the desire to develop equipment suitable for drilling raises large enough for manways.

Jan 1, 1963

By Rolph Linder

It is generally known and accepted that the efficiency of the blast furnace process, expressed by the symbols specific production and coke consumption, is influenced by a large number of variables connected to the type of burden, the alloy contents of the produced iron and the conditions of production as composition and preheating of the blast, the furnace heat losses and the possible use of fuels added on the tuyere level. It is furthermore obvious, that the coke consumption of the process will be influenced by specific production which could be said to be the result of two counter-acting influences. With high production, realized through intensive blowing, the passage time of the ore through the furnace is shortened leading to a decrease of the indirect reduction taking place in the upper part of the shaft within the temperature range of 300 to 1000°C. Simultaneously the external heat losses (constant in time) will be smaller calculated on each ton of iron and the resulting change in coke consumption will be the effect of both those influences. It is certainly of interest to be able to predetermine the effect of those variables before a change in the production practice is carried out.

Jan 1, 1964

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973