Search Documents

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By Alexander N. Winchell

The cities of St. Paul and Minneapolis are located side by side on a double loop in the Mississippi River near the eastern boundary of Minnesota. Both cities lie on both sides 'of the Mississippi River, which in this region describes an S-shaped curve. The two cities together have a population of over 600,000 people, gathered in an area which has grown to be a single urban district inasmuch as the two cities have expanded until they occupy all the territory formerly between them, though the business centers are ten miles apart. St. Paul is located at the head of navigation on the Mississippi River and Minneapolis, farther upstream, at the Falls of St. Anthony. A recent water¬power development below the Falls of St. Anthony, constructed by the Federal Government, has at the same time made possible navigation to the foot of St. Anthony Falls through a lock around the dam which replaces the former rapids. Minneapolis, in 1920, had a population of 380,000 people, and St. Paul, 235,000. The two cities occupy land at an elevation of 700 to 900 feet above sea level. The average elevation is slightly less at St. Paul. Minneapolis has nearly 4,000 acres of parks and park¬ways, while St. Paul has nearly 2,000.

Jan 1, 1920

By David H. Dahlem

Uranium is a very mobile element geochemically and is widely dispersed in the lithosphere and hydrosphere. Under oxidizing conditions, it is particularly widespread and appears in all parts of the surface hydrologic system. As a result, this system is a leading candidate in uranium-resource assessments as a new base from which total resources might be estimated. No other sampling system provides the large volume geochemical capture as the continental hydrosphere and is as pervasive and non-selective regardless of rock type. However, the water system as a uranium metal sampler is not without drawbacks as the development of a National sampling program based on it has shown, In spring 1973, the National Uranium Resource Evaluation (NURE) was announced by the U. S. Atomic Energy Commission (AEC). The program was conceived to provide an evaluation of the domestic uranium resources and to identify areas favorable for uranium exploration. The specific NURE objectives are as follows (Bowyer, 1974): 1. To provide a preliminary evaluation of domestic resources and favorable exploration areas by early 1976, based on existing data. 2. To conduct a comprehensive evaluation of domestic resources and favorable areas by 1980, based on advanced state-of-the-art information. 3. To conduct an R&D program into new and improved procedures, equipment, and technology for uranium exploration and assessment. 4. To disseminate information on new exploration concepts and technology.

Jan 1, 1976

By Evan Adams

The Ireland Mine is located some seven miles South of Moundsville West Virginia, along the bank of the Ohio River. We are mining the Pittsburgh #8 seam. This seam is approximately 60" in thickness, and is immediately overlain by some 10 feet of a conglommerate material. The roof is difficult to control, due to the fact that it frequently is composed of substances not hard enough to be held together with 6-foot roof bolts. In many cases, we must use 10-foot roof bolts, in order to get bolt anchorage in the limestone above the conglommerate. Due to the elasticity of the limestone and its tendency to bend rather than to break, we have been unable to maintain a pillar line. Thus, we have found it necessary to mine by the room and pillar system. Belt haulage is used on room entries to automatic loading stations, thence into 15-ton mine cars, controlled at the loading point by car spotters. The maximum belt length is 2,000 feet. Rail haulage to the slope-bottom dump is by 27- and 50-ton locomotives. The mine produces coal two shifts per day, with 7 production crews on each shift. Mine and machinery maintenance is performed on the Midnight shift. We handle an average of 660 tons per machine shift.

Jan 1, 1964

By M. A. A. de Klaver

Functional Description Figure 1 is a typical flowsheet for a system for solid fuel addition to filter cake. Solid fuel, coal, coal breeze, or charcoal, is fed from a,stockpile to a surge hopper. The solid fuel is metered into a grinding mill. The fuel is dried and ground in a grinding mill. The on-size particles are removed from the mill by air sweeping. The ground solid fuel is separated from the air stream by a cyclone and stored in a surge hopper. The ground solid fuel is then pneumatically conveyed to a small hopper in the balling area. The fuel is proportioned into the filter cake just prior to mixing. An efficient mixer is very important to have a successful operation. The exact flowsheet would depend on a number of factors including what fuel is used, how the fuel is received, and the cnaracteristics of the fuel as received. Availability of floor space in the plant may also affect the flowsheet. For example, drying air may be supplied from the pellet furnace if the grinding mill can be located near the grate, or the pneumatic conveying system and a surge hopper may be eliminated by placing the grinding mill adjacent .to the mixing area. Also, for a multiple line plant, a ball mill rather than a roller mill may be more suitable.

Jan 1, 1980

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By Min Chen, Qinghua Liang, Weishan Yan, Yuan Feng, Shigang Wang

Various coal mine robots (CMRs) and unmanned aerial vehicles (UAVs) are implemented to explore unknown mines for improving the safety and efficiency of mining. It is challenging for CMRs and UAVs to achieve accurate positioning due to the absence of the Global Positioning System (GPS), poor lighting conditions, and similar geometric features in complex mine scenes. LiDAR-based localization and mapping methods are more accurate than others, while long-time running in large-scale scenarios will introduce nonnegligible cumulative errors. This study presents a semantic-aided Li- DAR simultaneous localization and mapping (SLAM) with loop closure, which leverages the uniqueness of mine intersection structure to establish stable semantic loop closure. Specifically, we propose a semantic intersection descriptor of translation and rotation invariance, which encodes 3D point clouds of the same intersection from different positions and viewpoints into a unified image. By using the semantic descriptor, we can construct a constant loop constraint when the same intersection is revisited from different directions to reduce cumulative drift. We provide experimental validation using large data sets collected in two large underground mines, namely, a simulated Edgar mine deployed in ROS Gazebo and a public underground mine data set provided by ETH. Experimental results show that the proposed method has higher localization accuracy and outperforms the existing LiDAR-based SLAM strategies.

Feb 1, 2024

Resolution Copper Mining LLC (RCML) is currently in a Pre-feasibility study evaluating a large and deep copper and molybdenum deposit in the historic mining district east of Superior, Arizona. Work scheduled for the next several years includes dewatering the existing shut-down mine (the Magma Mine) and sinking an exploratory shaft to 2,130 meters (7,000 feet) below the surface. To dewater the Magma Mine and sink the exploratory shaft, RCML must extract and manage about 2 billion gallons of accumulated mine water inventory, as well as about 300 million gallons per year of new inflow. In order to conserve a valuable water resource in a desert environment, RCML worked with the New Magma Irrigation and Drainage District (NMIDD) to provide treated mine water to blend with and supplement the NMIDD?s water supply to approximately 2,000 hectares (5,000 acres) of farmland located east of Phoenix. A 44 km (27-mile) pipeline was needed to convey the treated water. It was essential that a treatment system be used which could reliably meet irrigation water quality goals, produce a non-scaling effluent to maintain pipeline flow capacity, and generate a dense sludge minimizing disposal cost and volume. This paper describes the resulting mine water treatment and recovery system (MWTS) and how the system has performed against objectives.

Jan 1, 2011

By Richard R. Klimpel

During the last 28 years, I have had the very challenging and rewarding experience of working as an engineering professional in a large multinational company, both as a manager of engineers and engineering projects as well as an inventor and generator of new engineering processes and products. Due to the diversified geographic and tech¬nical nature of my employer's business, my responsibilities have taken me all over the world. This has included interactions with people in different industries including minerals, coal, chemicals, petroleum, pulp and paper, agriculture and pharmaceuticals. As diverse as my experience may seem, it has always amazed me how common the basic underlying technology and economic trends are that shape the working environment that any given engineer in any given geographic loca¬tion will experience. I would like to discuss the industrial evolution from micro to macro engineering. One of the basic truths behind how industry must and will operate is "change," including: • the creation of conditions for change, • the anticipation of change, • the resistance to change, • the rewards that being part of a change can bring and • the destruction that change can bring to the unprepared. This fact was well stated by Heractitus around 500 BC.: "There is nothing permanent except change." This simple truth has been valid since the dawn of time and, if anything, is accelerating in nature every decade.

Jan 1, 1993

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By Charles S. Robinson

INTRODUCTION Geology, the science of the earth, is the fundamental science in the construction of a tunnel. The approximate site of a tunnel is determined by its purpose. The geology of the tunnel site will determine the cost--or feasibility of a tunnel--the specific alignment to accomplish the purpose of the tunnel, the design of the tunnel (within the limits of the purpose of the tunnel), and the methods of construction. The more accurately the geology of a proposed tunnel can be depicted, the more accurately can the cost of a tunnel be estimated. The factors that should be defined for tunnel design and construction are the physical characteristics of the material in which the tunnel is to be constructed. The physical characteristics of the material are determined by the genesis of the material, and subsequent geologic processes that have affected the material. The geologic materials in which tunnels are constructed can be broadly classified as unconsolidated and consolidated. The unconsolidated materials include chiefly deposits of recent geologic time that occur near the surface. Because these deposits occur near the surface, and tunnels constructed in them will be at shallow depth, methods of physical exploration such as geophysical methods, trenching, and drilling will give more data at relatively low cost--therefore the physical exploration is generally, or should be, quite extensive--and the

Jan 1, 1997

By David A. Lee

It was estimated in Chemical Week1 that the uranium fuel requirements for the U.S. Electric Utility Industry by the mid 1980's would be about four times that-of what it is today. This corresponds to approximately 45,000 tons per year of 'yellow cake' - of which a good portion is represented by ammonium diuranate - vs. the 11,700 ton total estimated for 1975. Perhaps just as significant is the 40-fold increase in thirty years projected for the entire world since 1970. Thus by the year 2000. 'yellow cake' production could be in the order of [3]50.000 short tons annually.2 'Yellow cake', so named because of its inherently bright yellow color, is a finely divided precipitate that can be formed after the leaching step when refining uranium ores. Feed solids enhancement then occurs to at least 50% by weight using filters or centrifuges This is followed normally by drying and then calcining with the conversion of ammonium diuranate to triuranium octoxide represented by the following equation: [9 (NH4)2 U2 07 heat 14 NH3 7 + 15 H2O7 + 2N2/ + 6 U308 4] Theoretically, assuming 100% conversion every 100 kgs. or 100 lbs. of ammonium diuranate will result in 90 kgs. or 90 lbs. of triuranium octoxide.

Jan 1, 1976

By John M. Dale

Now that the price of sulfur has reached unexpected high levels, it is little wonder that sulfur from surface ores is again receiving attention. In most instances, it is advantageous for an ore to be at or near the surface. However, it is a distinct disadvantage for sulfur ore to be close to the surface because it precludes the use of the Frasch process. The Frasch process depends on the presence of at least 180 m of uniform overburden to allow pressure injection of superheated water into the sulfur-bearing formation to melt the sulfur. In the Frasch process, sulfur separates cleanly from the gangue underground and comes to the surface in a very pure form. Surface sulfur deposits, particularly those in the Western Hemisphere, exist largely due to volcanic activity, and sulfur separation from the gangue is a formidable technical problem. None of the surface deposits are large compared to some of the Frasch deposits, but at the present sulfur price, they are certainly of economic importance. From the turn of the century until 1975, the price of sulfur was for the most part $18-$28/t. However, with the price of sulfur now over $154/t, there are a variety of technical alternatives to consider for sulfur surface ore separation that may not have been economically attractive a few years ago.

Jan 9, 1981

By Volkmar Niemitz

Approximately 30 miles east of Chicago on the southern shores of Lake Michigan stands Bethlehem Steel's newest fully integrated steelmaking facility - the billion dollar Burns Harbor plant. The initial phase of "green field" construction that began in 1963 was directed to the creation of high quality finishing facilities. In late 1964 the 160" plate mill came "on stream" followed closely by Sheet and Tin and Hot Strip facilities. Unit train shipments of slabs primarily from the Lackawanna plant located near Buffalo constituted the input materials for the new mills. In 1967 a hot metal facilities program was announced for Burns Harbor that at its completion would make the plant fully integrated. Incorporated within the program were: 1. A new high performance 50" x 96" slabbing mill complete with a battery of soaking pits. 2. A two vessel Basic Oxygen Furnace Shop. 3. (1) battery of 6 meter high Coke Ovens with attendant coal handling facilities. 4. A 3800 feet long vessel loading & unloading dock. 5. The first conveyor belt fed Blast Furnace in the United States. 6. An extensive materials handling system for receiving, stocking and reclaiming from storage the raw materials for the Blast Furnace and Coke Ovens operation. The intent of this paper is to provide a detailed description of the functions and components of the materials handling system noted above.

Jan 1, 1970

By G. C. Knutsen

The Post deposit is located in Eureka County, Nevada, about 37 km (23 miles) northwest of the town of Carlin. Post occurs on the Carlin Trend, a northwest alignment of 14 major gold deposits, each containing more than three tonnes (t) (100 000 ounces) of gold. Deposits of the Carlin Trend are epithermal, sediment-hosted, disseminated gold occurrences, collectively containing more than 622 t (20 million ounces) of gold. Three major gold producers active on the Carlin Trend are Newmont Gold Company (NGC) (12.4 t/400 000 ounces of gold per year), Western States Minerals Corporation (WSMC) and Pancana Minerals joint venture (1.56 t/50 000 ounces of gold per year), and Dee Gold Mining Company (1.4 t/45 000 ounces of gold per year). The Carlin Trend has also been referred to as the Lynn-Railroad Mineral Belt. This district is characterized by open-pit mineable, micron-sized gold, hosted in Paleozoic sedimentary rocks. Six geological subdistricts comprise the Carlin Trend, each characterized by differences in host lithology, structural controls, alteration assemblage, or style of mineralization. The six geologic subdistricts include, from south to north, Bullion (Railroad), Rain, Maggie Creek, Lynn, Bluestar-Goldstrike, and Bootstrap. With the exception of the Bullion subdistrict, which was primarily a producer of base metals, each sub-district contained mineable reserves in excess of 31 t (one million ounces) of gold.

Jan 1, 1987

By William E. Lamont

As a part of the Department of the Interior's rutile and titaniferous materials development program conducted under the Defense Production Act, the Bureau of Mines investigated the potential for producing national stockpile grade rutile from plant products of phosphate beneficiation plants operating in the central Florida pebble phosphate district. The potential for producing ilmenite, zircon, and monazite concentrates from the plant products was also investigated. Results of these studies indicated that 3,000 to 6,000 tons of rutile, 28,000 to 55,000 tons of ilmenite, 9,000 to 19,000 tons of zircon, and 400 to 800 tons of monazite passed through the plant circuits annually. All of these minerals are presently being sent to waste ponds. Beneficiation of a bulk heavy mineral concentrate separated from the amine flotation tailing (froth product) of numerous plants in the district showed that it was possible to produce a rutile concentrate containing over 94 percent Ti02. Additional studies showed that over 70 percent of the Ti02 in the rutile concentrate could be isolated in a product containing 98.0 percent Ti02. The studies also showed that it was possible to produce ilmenite concentrates containing 63 percent Ti02, zircon concen¬trates containing 65 percent Zr02, monazite concentrates containing over 85 percent monazite [(Ce,La,Y,Th) (P04)], and xenotime concentrates containing over 35 percent xenotime (YPO4).

Jan 1, 1969

By D. Bradbury

Sufco coal mine, a subsidiary of Arch Western Bituminous Group, recently purchased a reverse osmosis (RO) system. The systems intent was to remove impurities in the water being mixed with the hydraulic oil to maintain the viability of critical longwall hydraulic systems and to prevent degradation. This project not only ensured hydraulic components from corrosion, but also revealed a cost savings by reducing the percentage of hydraulic oil mixed with the RO water. SUFCO WATER TREATMENT HISTORY Sufco coal mine has been in operation for approximately 70 years. Old works extend up to 15 miles one way, not including adjacent mined out longwall panels. Due to the geologic conditions and strata, water treatment has been as simple as putting water in at a high point of a mined out area and recovering it at a low point to discharge. Doing this reduces the total suspended solids (TSS) to less than 25 parts per million (ppm) and the total dissolved solids (TDS) less than 1,200 ppm which complies with Sufco?s water discharge permit. Even though the requirements for the permit were met, the water is still corrosive in nature. A portion of this water is piped back into the fireline (makeup) water system. It is then boosted to pressures of up to 500 psi to support mining sections, belt systems, equipment, fire fighting systems and the longwall.

Jan 1, 2011

By A. Unal, H. Sevim

The utilization of high-sulfur Illinois coal by utility plants has been decreasing since the enactment of the 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal more attractive by offering the choice of taking the coal combustion and flue-gas desu furization products from the utility plants and placing them in the abandoned sections of their mines To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of product disposed of can be minimized In this paper, several such systems are presented The favorable operating conditions of each system are determined in terms of distance and tonnage ranges. For a 90 kt/year (100 thousand stpy) operation, it is found that, up to a distance of 150 km (93 miles), transporting products by truck would be less expensive than using rail cars and intermodal containers. Also, a case study is given in which a cost analysis is conducted for an underground coal mine receiving products from two Illinois utility plants. At 90 kt/year (100 thousand stpy) and a distance of 40 km (25 miles) between the power plant and the mine, it is found that truck transportation and under ground placement would cost $0.090/tkm ($0.131/st-mile) and $2.98/t ($2.70/ st), respectively.

Jan 1, 1999

By Michael G. Li

Prediction of acid rock drainage (ARD) for low-sulphide, low-neutralisation potential (LSLNP) mine wastes is methodologically different from that for normal sulphidic mining wastes. In this paper. LSLNP wastes are conveniently defined as those with S2 < 1% and ABA-NP2 < 20 kg CaCO3 eq/t. The distinctiveness of ARD prediction for LSLNP materials originates from their frequently low oxidation rates and is mainly attributable to two reasons. First, the utilisation efficiency of available carbonate neutralisation potential (CNP2) rapidly deteriorates when the sulphide oxidation rate per unit mass of waste drops below a certain level. Reducing the flushing rate of a waste has the same effect as increasing the oxidation rate. Second, silicate neutralisation becomes increasingly important as oxidation rates diminish, and can no longer be ignored in LSLNP materials as it often is for normal sulphidic mine wastes. In this paper, the effects of oxidation rate, pore gas CO2 partial pressure, and flushing rate on ARD prediction for LSLNP materials are theoretically demonstrated with the help of modelling using the computer program MINTEQA2. A new methodology for ARD prediction for LSLNP materials is presented in terms of a prediction procedure. Finally, a case study is given to validate some of theoretical aspects discussed and to illustrate the use of the newly proposed ARD prediction procedure.

Jan 1, 2000

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

The principle of high-pressure interparticulate comminution has been used very successfully since the mid 1980's for grinding a wide range of different materials. A number of reports about operating experience have already been published. High-pressure grinding rolls (HPGRs) are currently making their debut in the mining industry. Experience is being gained with test machines, particularly for the comminution of hard rock. In the grinding of diamond-bearing ore, (Fig 1) interparticulate comminution has already become the standard for liberating the diamonds from the matrix. The advantages of interparticulate comminution are also recognized for the grinding of concentrates (chrome ore, iron ore). Numerous HPGRs are being used very successfully in this field. A testing plant for first-time industrial grinding of coarse, very hard and highly abrasive copper ore was built at Cyprus Amax's plant in Sieretta, Arizona (Fig. 2). The operating experience gained here showed that the grinding of very hard ores places particularly high mechanical demands on the mill. While the machine itself meets the high availability requirements, the wear-protection system proves to be the most sensitive point. Naturally, the properties of the ore to be ground exert a considerable influence on the lifetime of the grinding rolls. This paper describes the wear mechanisms and the wear­protection systems designed to combat these.

Jan 1, 1997