Search Documents

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

By Bauer, Steve, Colin Goodwin, Gerald, Randy Dempsey, Courtland

"The City of Ottawa’s Combined Sewage Storage Tunnel consists of two interconnected tunnels totaling 6.2 km with a diameter of 3m including access shafts and hydraulic structures which connect to the City’s most critical sewers. This tunnel will be built 15m to 30m below ground in the downtown core adjacent to, and crossing below, the Light Rail Tunnel, which introduces additional considerations in terms of sequencing and risk mitigation. The City embarked on a unique Procurement Process to address the risks involved with a large tunnel project and those associated with tunneling below downtown, underneath and adjacent to UNESCO World Heritage Sites, and connecting to live critical sewers. This paper describes the unique procurement approach employed and the contractual risk mitigation measures developed to provide the best value while minimizing risk. Specific features include Market Sounding, using a Fairness Commissioner, Contractor Prequalification and Risk Mitigation Measures in the Tender documents. INTRODUCTION This paper describes how the City of Ottawa (the City) and the project design team developed a strategic Procurement Process and Tender that incorporated industry best practices for technical and contractual risk management for the Combined Sewage Storage Tunnel (CSST) project. The process was unique in that, while it employed a systematic review of project risks, it also solicited input from industry, stakeholders and provincial and federal partners to develop the request for Tender for this traditional design-bid-build project. Key drivers for this approach were initiated from the City’s concerns for cost control, cost certainty and overall project risk mitigation. To address these concerns, the City implemented the risk review and mitigation process right from the project design team selection. It was critical that the project design team embraced this risk management philosophy and carried it through each phase of the project. This paper serves as an excellent resource for municipalities or other owners embarking on a similar tunnel project, on how to properly apply industry best practices and the benefits of using them."

Jan 1, 2016

By Aidan Giblett

"It is important to make a clear distinction on the scope of work of the Global Mining Standards and Guidelines (GMSG) guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and consequently require a large amount of information to calibrate and validate the unit models. As a result, these surveys are labour intensive, somewhat expensive, depending on internal capabilities of the mine site or company and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions.As a result of these factors, full grinding circuit surveys are not a common occurrence at a large number of processing facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices.To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result, it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. These methods can also be manipulated by an experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, allowing an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2015

By R. C. Schmidt

The Mont Klahoyo magnetite deposit is located about 600 km northwest of Abidjan, Ivory Coast. During an exploration period ending in 1977 an international joint venture group investigated the deposit and proved reserves of 670 million tons grading 36% iron. The deposit, occurring at the northeast end of the Baoubly-Kiriao chain of Precambrian iron formations, is associated with amphibolites, pyroxenites and gneisses of the Liberian Shield. At Mont Klahoyo occur two separate iron formations of which the lower member is the ore body. This lower member consists of a highly metamorphosed - banded quartz-magnetite iron formation in which iron silicate bands alternate with beds of quartz-magnetite. mphibolite-pyroxenites and sillimanite-cordierite-garnet gneisses form hanging and footwall rocks. The iron formation has been folded into an elongated overturned "Z" shaped major drag fold with axes trending and plunging approximately northeast. Beds are vertical or dip steeply to the southeast. The ore zone has an average thickness of 130 m and outcrops intermittently over a distance of approximately 5.5 km. Based upon detailed studies of drill cores and the results of ore dressing test work, eight stratigraphic units, identified as K-1 to K-8, are recognizable in the iron formation. Four interbedded units are low grade silicate zones (silicate facies) with the remaining quartz-magnetite units (oxide facies) repre¬senting the important ore zones of the Mont Klahoyo deposit. The ore-bearing "K" units are subdivided further, based upon their specific lithologies, iron content and concentration characteristics, into eleven ore types. The identification of these ore types is considered particularly important to mine planning and flowsheet design. A cap of oxidized materials overlies the primary quartz-magnetite iron formation but no enrichment has occurred. It is proposed that the Mont Kalhoyo iron formations were deposited, possibly chemically, in a volcanic environment as a siliceous iron formation with volcanism providing the primary source of iron and silica. Metamorphism converted the siliceous iron formation to a relatively coarse-grained quartz-magnetite-silicate iron formation.

Jan 1, 1979

By Harry E. Holzschuh

The two Agrico Chemical Company self unloading Phosphate Rock barges put into service in 1976 operate at over their design carrying capacity. Each barge now carries 26,000 short ton instead of the planned 25,000 short ton at 32 foot of draft. They are in service between Agrico's Tampa, Florida Terminal and the Donaldsonville, Louisiana Fertilizer Complex, moving a total of 2,500,000 short tons each year. This was the first use of the Parascrew design for a marine application. The barges, with their 3,000 STPH unloading and matching loading rate is the vital link in this total transportation and handling system. Rock is moved from the Pierce, Florida Mines through the Tampa Big Bend Terminal, across the Gulf of Mexico, and up the Mississippi to the Agrico Faustina Phosphoric Acid Plant 30 miles below Bacon Rouge, Louisiana. The trip from the terminal to the plant is 600 miles and the turnaround time is just about six days. Seven years operating experience has proved that the system works. Fittingly, the two barges are named the "Faustina" and the "Pierce". They have a beam of 85-feet and are 495 feet long. folded depth is 43 feet, with a ballasted light draft of 19 feet and a typical loaded draft of 32 feet. There are four separated holds with the machinery room located forward of 101 hold. Each hold is 51 feet wide at the coamings with an 18 foot straight section on the side, and a 24 foot long, 600 slope sheet for a 23 foot clear reclaim width at the bottom. The Parascrew in each of the holds is 37 feet long between the bearings and is supported on a 14 inch diameter hollow shaft. The screw pitch varies and the diameter of the flights step up from l'-9" diameter to 2'-6" diameter on the discharge end. By sloping the centerline, a minimum four inch bottom clearance is maintained across the hold. Some bending of the tube does take place.

Jan 1, 1983

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

By J. Schoenbacher

Park City Municipal Corporation (PCMC), long before being recognized as an Olympic venue was known as one of the great American silver mining towns. During a century of active mining, the Park City mining district produced millions of ounces of silver in addition to a substantial amount of mine tailing waste. Since 1985 the City has been remediating these impacts with state and federal oversight. One particular challenging CERCLIS site, that was previously a historic mine tailings pond is known as Prospector Square Development (CERCLIS Listing Silver Creek Tailings UTD98051404). This site has been very challenging due to the metals that impact the shallow ground water that eventually drain into the Silver Creek Watershed. To address the water quality impairment the City and Missouri University of Science and Technology teamed up to investigate the feasibility of constructing a horizontal-flow wetland to treat this pollutant source. This effort began with the building of a pilot cell in June of 2004 and lead to the construction of a full scale horizontal-flow wetland in the fall of 2008. The design of the pilot and full scale biocell was based upon lab-scale research conducted by the Missouri University of Science and Technology. In October of 2008, the Prospector Drain effluent was introduced to the system and to date analytical results reveal that the biocell is treating the Prospector Drain outfall below the Silver Creek Total Maximum Daily Load (TMDL) endpoint goals for zinc .39 mg/L and cadmium .00075 mg/L. The water chemistry of the influent, that originates from the historic silver mine tailings pond, is impaired with zinc and cadmium and has low iron with a pH of roughly 6.5. The construction of this unit encountered many challenges related to constituent relations, regulatory scrutiny, constructability and start-up. Nonetheless, since implementation this unit is considered a success for improving water quality within the Silver Creek Watershed.

Jan 1, 2011

By J. S. Gardner, K. E. Houston, A. Campoli

INTRODUCTION Disposal of coal refuse is a costly and challenging problem facing the coal industry today. After the Martin County Coal Company slurry spill and the subsequent regulatory changes state and federal agencies are now beginning to require companies to justify new slurry impoundments. The authors have performed an analysis of different means of disposing of coal refuse for a major coal producing company located in the eastern Kentucky coalfields (the name of which will be withheld for the purpose of this paper). The company’s existing slurry impoundment is nearing its maximum permitted elevation and also an elevation where it may come in contact with abandoned underground workings. Due to the increased concern with underground mine works near slurry impoundments, additional consideration was given to raising the existing impoundment. Several other alternatives were evaluated, including but not limited to raising the existing impoundment, constructing a new slurry impoundment, constructing slurry cells, belt presses and others. This alternatives analysis was performed as part of a Section 404 permit for a valley fill and is currently being reviewed by the U. S. Army Corp of Engineers. All of the known possible alternatives were discussed in detail in the analysis. Due to the findings of the alternatives analysis, the company considers the engineered construction of the proposed impoundment to be the most favorable option of all the other alternatives evaluated, from both an economic and environmental standpoint. ALTERNATIVES EVALUATION FOR COALREFUSE/SLURRY DISPOSAL Background The company currently operates several deep mines and employ over 300 people and produces over 3.9 clean Mt/a (4 million stpy) of high quality, low sulfur coal. Currently, coarse refuse is belted to a valley fill, while, fine refuse is pumped to the existing impoundment. Coarse refuse is trucked to the existing impoundment as needed for construction purposes. The average recovery is approximately 50%; therefore, over 3.9 Mt/a (4 million stpy) of coal refuse must also be separated and placed.

Jan 1, 2003

By C. Tsamantaki

Water-bentonite suspensions exhibit a yield stress which is defined as the minimum applied stress for flow. Considerable debate exists about the yield stress being a material property, hence different measuring methods should give similar answers, but several investigators have demonstrated that it is an engineering reality. Yield stress is normally estimated indirectly from the rheogram obtained with a viscometer following an extrapolation to zero shear rate (the dynamic yield stress), but the technique may be prone to errors because of slip flow. Direct measurements, not prone to such errors, rely on an independent assessment of the yield stress, normally carried out with the vane method (the static yield stress). In this paper results are presented and compared regarding the yield stress of 14 different water-bentonite suspensions measured using both the direct and the indirect methods. In order to obtain a wide range of yield stress values, two different types and two concentrations of bentonite at various pH were tested. Rheological data were obtained using a rotational speed viscometer and a yield stress vane measuring device. Measured vane yield stress values ranged from 5 Pa to 83 Pa. Rheological data collected with the rotating viscometer were fitted using various conventional techniques (interpolation, linear and non-linear regression analysis) as well as using a golden section yield stress search methodology based on Herschel-Bulkley model, developed in house. The vane instrument measures directly the yield stress of the suspensions and requires no further data handling. A comparison of the measured values of the yield stress with the direct and the indirect method is then made for the water-bentonite samples. Not very large differences are observed among different techniques and the variations are discussed. Similar data from literature are also analyzed and the comparison shows that differences on the various estimation methods are much larger than the differences observed in this study.

Jan 1, 2006

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60's and early 70's efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70's. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By A. Venkatachalam

Spinel ferrites, like NiFe2-2x Znx Ti4 O4 Fe CO1.5 Ge0.5 Tix O4, Ga1-x Fex Ni CO O4, Nil-x Fex Mn2 O4 have been prepared using the respective metal oxides in Stoichiometric quantities, by the ceramic method. The oxides were homogenized in acetone medium, pelletifed by using poly vinyl acetate as the binder. They were fired at 1000°C for 100 hours for compound formation. Chalcogenide spinels such as Zn1-x Cux Cr2 Se4 where 0=x=l and Cu1-x Fex Cr2 Se4 where 0=x=0.3 have been prepared by using 99.99% pure elements and then fired at 1000°C in quartz ampoules under vacuum conditions. X-ray diffraction studies of these compounds indicated a single cubic spinel phase. DC resistivity studies of the compounds were taken between 300-700K using LCR bridge by two probe technique. Thermo-electric power measurements were taken between 300-500K for all the compounds. Initial susceptibility studies have been carried out using a low field (0.506) and from which the nature of magnetic dimains and Curie temperatures were determined. Magnetic hysteresis measurements were carried out at 300K and at 80K, using alternating current hysteresis loop tracer, at 2K02 field. Mossbauer spectral measurements were carried out using Co57 source embedded in a copper matrix and an absorber containing 0.3 mg/cm2 of the sample. The spectra has been fitted by Mossfit Program. The catalytic effect of the spinel ferrites NiFe2-2x Znx Tix O4 where 0=x=1 has been studied by using the model reaction of decomposition of H2O2 at temperatures from 40°C to 70°C. It was found that the spinel oxides were found to possess poor catalytic activity.

Jan 1, 1990

By S. S. Churchill

Introduction Amidst the apparent chaos of the final push to complete a major construction project, a small group of specialists works with great intensity. Armed with yellow "in test" and green "turned over to operations" tags, these startup engineers follow detailed preoperational test procedures to confirm that a plant is ready to operate. They follow a test schedule designed to complete individual process system in the order they will be needed by operations. After extensive preliminary testing, the startup engineers begin the truly exciting part of their work - initial operations. The thrill of engaging the clutch for the first time on a 10,000 horsepower grinding mill makes all the long hours worthwhile. Preoperational testing and startup are of critical importance to the success of a project. No other aspect of a construction project allows such opportunities for success or failure, and no other aspect is so critically influenced by careful planning. At Bechtel, the tasks of preoperational testing and startup are among the responsibilities of the Mine and Plant Operations group. The Preoperational Testing Process Preoperational testing is the transition phase between constructon and startup on a new plant. It includes the preparation of detailed test schedules and procedures. The schedules are used to coordinate construction completion activities, so that systems are available for startup and operations in a rational sequence. The procedures form the basis for performing the testing and documenting its completion. Tests include instrument calibration, wire insulation tests, wire termination verification, mechanical alignments and inspections, and system cleaning and flushing. Where possible, the systems are then operated on water and their performance recorded. Normally, either the construction contractor or a team of specialists has the responsibility to perform preoperational testing. Witnesses to the testing may be owner operations and maintenance personnel, engineers from the design firm, or specialists assigned to the project who provide assistance and guidance to the contractor in addition to witnesing the work.

Jan 1, 1986

By A. M. Stone

INTRODUCTION In ore beneficiation one of the simplest methods of mineral concentration is hand picking to remove either the ore or the waste material from a moving table or conveyor belt. Ore Sorting Equipment may be defined as equipment for mechanized picking. This type of equipment has been used successfully over the past thirty years or so to beneficiate ores of various types in particle mesh sizes between 1mm and 200mm.. at throughputs of up to 150 tonnes per hour. In general for ore sorting to be a consideration the ore and the waste material must be well liberated in the feed to the sorter (that is into practically discrete particles of ore and waste). The larger the liberation size the more likely sorting is to be cost effective. Correct selection of ore sorting equipment is most important and often special machine features are developed for an individual application. Sorter performance can be best determined by extensive testwork of representative ore at design tonnage on prototype or preferably on production model sorting machines. ADVANTAGES OF SORTING ORE The four main advantages of sorting ore are: Reduced milling cost. Reduced processing cost. Higher overall recovery. Reduced transportation costs. Reduced Milling Cost With sorters installed the milling plant following the sorter is generally smaller and hence less costly to install and operate as it only has to handle the sorter product. However this benefit is somewhat offset by the increased cost of the screening and washing plant prior to the sorter and the cost of the sorting plant itself. Reduced Processing Cost As there is less material of higher grade presented to the concentrating plant following the sorter, this plant will generally be smaller and less costly to construct and operate than a plant treating the total quantity of material. Higher Overall Recovery The economic recovery is often misunderstood by plant operators when evaluating the advantages of sorters

Jan 1, 1986

By Thomas G. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with prebenching or serving as the primary tool, dozers are important in driving down mining costs. This article reviews the application zone of track-type dozers. It also provides suggestions for site setup, equipping tractors and machine operation. In recent years, the track-type tractor has become more of a production tool in mining. With the advent of bigger machines, bulldozers have become a typical component in mining operations, removing overburden down to the top seam of coal. Large tractors can also be teamed up with draglines and other systems to maximize the effectiveness of the mining system. Bulldozers remain the tool of choice for topsoil removal, spoil reclamation or any application that demands low ground pressure, or short distance. The introduction of the 523-kW (700-hp) track-type tractor to the mining industry has made the bulldozer a low-cost-per-ton means of removing overburden. The large tractors offer enough productive capability to be considered prime stripping tools. And they can lower mining costs by complementing other mining systems (dragline, cast blasting and loader/truck). Four criteria determine whether a track-type tractor is the right machine for a particular application: ? Production requirements - dozer may fit job requirements better than a second dragline. [ ] ? Product support - availability of parts, service and technical expertise. ? Labor situation - how much of the cost per ton goes to the operator. ? Resale opportunity - recover a percentage of capital cost. Mining efficiency is economically controlling the cost of any system. Most operations rate the most economical means of moving material as cast blasting, dragline and the track-type tractor. All three of these systems share one common value: They are all sensitive to distance. Regardless of the application, all mining systems have an economic range. Exceeding this distance will affect cost and productivity.

Jan 1, 1997

By K. E. Robinson, G. Re, L. Skoski

Introduction A new technology is evolving as a result of growing industry and government concerns over the potential impacts of possible airborne emissions from uranium tailings piles. A major component of the technology is the use of earth covers to stabilize the tailings after mill operations have ceased. While various analytical models have been used to predict the thickness of required covers, experimental validation of the models has been necessary. This paper presents the results of a field program to select and test cover material to determine its suitability for eventual reclamation of a currently active tailings pile. The two main criteria guiding the study were the U.S. Nuclear Regulatory Commission radon flux requirements (reduction to less than twice background pre-1979, and to 2 pCi/m2 -sec above background post-1979) and the desire to employ locally available material. The methodology chosen for this study consisted of three main elements: o Determination of the background radon flux. o Determination of the radon flux from the tailings pile. o Experimental determination of the cover material diffusion coefficient and and calculation of cover thickness. The first two elements of the study are relatively straightforward, the last phase is discussed in detail. Background Radon Flux Measurements of radon-222 emanation rates from the surface of the ground were taken at three sampling locations. Samples were collected by means of the accumulator can method described by Wilkening, 1977. Both morning and afternoon samples were collected at each site to obtain an average. The measured fluxes were fairly uniform and did not differ greatly among sites. The overall average flux for all sites was 0.63[+]0.28(o) pCi/m2 -sec. This value is equal to the average radium-226 concentration determined in the soil, thus yielding a one to one ratio of radon-222 emitted (in pCi/m2 -sec) to soil radium content (in pCi/g). Tailings Pile Radon Flux Two sites on the tailing pile

Jan 1, 1980

By Wayne Charlie, Joseph P. Martin

INTRODUCTION Typically, uranium mills produce slurred tailings which are transported by pipeline to a tailings impoundment. The slurried tailings contain about 250 solids (75% liquids) by volume and, depending on the milling process, have a high or low ph. Despite decanting water from the tailings pond and losses by evaporation and seepage, Staub (1978) estimates that for lined impoundments over half of the input water is stored in the tailings. As long as the impounded tailings remain in a loose and saturated state, potential hazards exist and include potential for short and long-term seepage from the impoundments and the potential for large scale release and movement of liquified tailings should an embankment fail. The breach of an earthen dam on July 16, 1979 at Church Rock, New Mexico, and the subsequent release of 100 million gallons of water and liquified uranium tailings, underlines the potential hazard. Loose saturated tailings also have a high potential of liquefaction during earthquakes (Charlie and Wardwell, 1979; Martin, Finn and Seed, 1978; and Mittal and Morgenstern, 1976). If the tailings could be dewatered, the liner's integrity would become less critical, longterm seepage and settlements would be greatly reduced. In addition, the potential for tailings liquefaction from an embankment failure or earthquake would be greatly reduced. This paper reviews the concept, criteria, and design of various proposed interior drainage systems to dewater the tailings after deposition. ADVANTAGES OF INTERIOR DRAINAGE The primary purpose of interior drainage systems for uranium mill tailings impoundments is dewatering the tailings as rapidly and as thoroughly as possible. The expected benefits of this new technology are: • Reduction of potential seepage losses by decreasing the hydraulic head. • Reduce earthquake liquefaction potential of the tailings by inducing non-saturated conditions and/or lowering the water pressure. • Reduce the potential for large-scale release and movement of tailings should an embankment fail. • Stabilize the tailings to permit early reclamation. • Recovery and potential recycling of tailings liquid. • Inhibiting long-term seepage out of the impoundment by inducing nonsaturated conditions to provide capillary suction in the tailings.

Jan 1, 1980