Search Documents

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By Wendell E. Bearce

At the, Crescent Valley Mine of the Hanna Coal Company, several 10,000 ton unit trains of 41" x 0 strip coal are loaded per week during the lake season. This is accomplished without the use of any accumulation of prepared coal. A large raw coal pile is built up during the winter months adjacent to two truck dump bins. This is added to whenever trucks are coming in from the pits and trains are not being loaded. During the loading of trains, trucks from several pits dump into the truck hoppers and coal is also dozed in from the pile. At a rate up to 3200 tons per hour this coal is screened, the plus 6" hand picked, the plus 4" crushed, and' all weighed and sampled as it goes directly to railroad cars being handled on two tracks by car retarders. With such an arrangement it is possible to exercise some control over coal quality, if it can be assessed rapidly. For instance, if the moisture rises to a level where it seems probable the BTU per pound will be reduced to the point where the contract calls for penalties, the trucks from, the wettest pit may be stopped, more or less coal may be moved in from the stockpile, or other measures taken to assure that the average BTU of the trainload will be satisfactory.

Jan 1, 1967

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By Robert Vergie

Like most of you, I would rather work on a job than talk about it. But it is fruitful to spend some time taking stock of important developments in the heavy construction field. One of the strongest recent movements affecting the industry has been the push for safety. I regret that it is a recent development. Not that builders were against safety. Too often though, it was easier to continue with dangerous old work methods than to try something new. Too often, it was easier for equipment manufacturers to build production tools with little consideration for worker safety. And too often, accidents and gruesome disasters occurred. The ultimate result of on-the-job injuries in construction and other industries was the Federal Government's Occupational Safety and Health Act of 1970. Individual states were required either to accept OSHA or pass updated regulations at least as stringent as the Federal requirements. These new rules must be strictly obeyed -- not just because they carry civil and criminal sanctions -- but because they correct unsafe conditions and reduce hazardous acts. Though some OSHA measures have been criticized as superfluous, most of them do in fact save lives and limbs. Equally important, the tunneler who follows the new safety regulations can be fairly certain of an efficient, uninterrupted operation. Regulations do sometimes bring rewards.

Jan 1, 1974

By W. M. Hart

Business Process Improvement (“BPI”) Change to Survive “It is not the strongest of species that survive, nor the most intelligent, but the one most responsive to change.” [Charles Darwin] “If you want to understand something, try to change it.” [Kurt Lewin, social scientist] Many companies have tried one or more process management initiatives. Each effort may help develop a culture that is more receptive to change. Executive Management needs to be unwavering in support of change with systems and structures, staffing, development of people, measures, with incentives and rewards. General Electric developed principles for quality change management that are necessary for effective, continuing Business Process Improvement (BPI). Change Acceleration Process (“CAP”) One of the tools General Electric developed has been used successfully by companies around the world in a wide variety of industries. This tool, named Change Acceleration Process (“CAP”), is designed to improve acceptance of change. Acceptance is the method by which the creative energies of the workforce can be fully tapped. Over time, every employee receives CAP training at least once, and in many instances three (3) or four (4) times, and will work on one or more High Performance Teams. Thus, BPI can achieve and maintain its goals. The CAP tool focuses on: • Leading Change • Creating a Shared Need • Shaping a Vision • Mobilizing Communication • Making Change Last • Monitoring Progress • Changing Systems and Structures

Jan 1, 2006

By Gian-P. Lozej, Ross Y. Black, Sami S. Maddah

The Zabirah bauxite is a Cretaceous paleolaterite exposed by postTertiary uplift and erosion of the Phanerozoic sequence. The laterite profile, which is preserved in situ, occupies a prominent angular unconformity over a sequence of sandstones, siltstones and mudstones ranging from Late Triassic to Early Cretaceous in age, and is overlain by a Late Cretaceous terrigenous and carbonate package. The profile is known to be preserved over an area of 250 sq km and at depths below the present surface of up to 80 m. The bauxite layer is hard, compact and predominantly pisolitic, with a variety of subordinate, superimposed textures resulting from post-formation alteration. The bauxite minerals are boehmite and gibbsite. Boehmite generally predominates, and the boehmite:gibbsite ratio averages 2:1, with a marked tendency for the proportion of boehmite to increase down the profile. Kaolinite, a major constituent of the profile, is concentrated in two zones, one above and one below the pisolitic bauxite layer. Iron content is variable and bears a direct relationship to parent-rock lithology. Genesis and preservation of the bauxite are due to the favourable coincidence of a number of geological controls of which the most significant are the local structural and sedimentary regimes, the lithology and chemistry of the parent rocks, and the Cretaceous paleogeography of the region.

Jan 1, 1984

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

By P. Bester, G. J. van der Linde

Foskor operates a mine in the Northern Province of the Republic of South Africa exploiting the igneous complex at Phalaborwa. It produces about 3 million tons of phosphate concentrate per year by means of froth flotation from 26million tons of ore of which 16 million is mined and milled onsite. The remaining 10 million tons originate at the Palabora Mining Company and is pumped as a slurry to Foskor. Two types of ore are mined and milled namely Foskorite and Pyroxenite. (The main mineral content of this ore is Apatite, Phlogopite and Diopside.) After three stages of crushing the ore is milled using 24 rod mills and 5 verti mills. The apatite is then recovered using four stages of froth flotation. The stocks of Foskorite ore are rapidly being depleted and the PMC tailings will also fall away by the year 2002 so that the whole mining operation will then be centred around the Pyroxenite ore. This will lead to substantial increases inproduction costs. The recoveries achieved in the flotation plant are largely dependent on the successful operation of the comminution section. Parts of this plant are now 35 years old and the advantages of re-engineering, new technology and automation can only be applied to a limited extent in an effort to reduce costs. It was then decided to investigate alternative milling methods, both wet and dry.

Jan 1, 1999

By Maurice Deul

Certain health and safety hazards occur entirely unexpectedly in some subterranean excavations. Although ground support is not the subject of this paper, ground failure can result in large and often uncontrolled flow of fluids into an excavation. Even when there is no ground failure, the disturbance of nature's equilibrium between rock or unconsolidated alluvium or rubble and the contained fluids poses severe problems to a well planned operation. Optimum conditions for safe operation cannot be the sole criterion for site selection. Some mineral deposits form in zones of structural weakness, others form where hydrothermal alteration substantially weakens the enclosing rock, and tabular deposits such as coal and evaporites inevitably undermine large areas. Excavation to acquire mineral values cannot be relocated. The same is often true for tunnels driven to connect distant points by the most direct route. Rivers and mountains cannot he avoided, and the cost of lengthening a tunnel--by even a fraction of a percent--must be strongly justified. No responsible engineer will knowingly select a dangerous route for excavation, but to what extent do engineers attempt to assess the health and safety hazards that may be reasonably expected? How, specifically, can methane explosions, water and sand flooding, dangerous dusts, toxic gases, thermal shock and radar poisoning be eliminated or minimized through systematic advance planning?

Jan 1, 1974

By Walter Hoecker

The dissolution of gold in cyanide_ leaching has been we11 published with the genera1 acceptance that gold is oxidised by oxygen and stabilized by complexation with cyanide [1]. The dissolution of gold is essentially an electrochemical process. The rate of the anodic gold dissolution is controlled by the cyanide concentration. - (2) While the cathode reduction of oxygen is controlled by dissolved oxygen concentration - (3) There are a number of factors influencing the concentration of oxygen, and if 1owered substanth.lly will effect the efficiency of the leaching plant. These include: "' salinity "' temperature "'partial pressure "'oxygen consumption rate The use of pure oxygen for· cyanidation is only beneficial if oxygen is rate limiting, Conversely a slurry saturated with air (typically 5 - 8 ppm) may not be enough for maximum leach rate. The diagram below shows the maximum dissolved oxygen levels obtainable with pure oxygen and air. DISSOLVED OXYGEN (MAXIMUM) IN WATER At steady state, the rate of the cathodic reaction must equal the rate of the anodic reaction. Thus the rate of gold dissolution is dependent on both the· cyanide and oxygen concentrations. - (4) Using an average of Do/Den =· 1.5 [2] (where Do and Den are the oxygen and cyanide diffusion coefficients) the table below illustrates the maximum effective oxygen concentrations for given cyanide levels in clean water [3].

Jan 1, 1992

By George M. Potter

Precious gold and silver markets support substantial activity in the search for and development of improved and unconventional ore and tailing processing methods. The need for such methods 1s strengthened by consideration of increasingly low grade and refractory ores and old tailing reserves. As background for this review of new and unconventional precious metal processing, recent USBM data (1981) show annual world gold production of about 40.8 million troy ounces. In the U.S. about half the 2.8 million ounce consumption was used for jewelry and the arts, 39 percent for industry, and 8 percent for dental purposes. World silver production in 1981 was about 365 million ounces. Domestic usage the same year was about 117 million ounces. More than $ was used for photography and 30 percent for electrical and electronics. By process, about 1 percent of U.S. production of gold came from amalgamation, 66 percent from cyanidation, 31 percent from smelting ores and concentrates, and 2 percent from placers. As for silver, about 11 percent is from cyanidation and 89 percent from smelting ores and concentrates. Evidently the search for innovative and unconventional precious metal processes must include gravity concentration, froth flotation, hydrometallurgical, and electrometallurgical methods. Although smelting processes are equally important, they largely comprise nonferrous metal technology, and are not discussed here.

Jan 1, 1984

Energy Developments Ltd. (EDL) has developed power plants at two Australian coal mines that featuring 94 gas-fueled Caterpillar G3516 engine/generator sets. They will convert to electricity 145 kt/a (160,000 stpy) of coal-seam methane gas for sale to a local utility. The $100-million project will cut the sites' methane emissions in half, provide a low-cost energy source and offset mine operating costs. The project began in May 1995. It is located at the Appin and Tower longwall underground mines, 80 km (50 miles) south of Sydney in New South Wales. The installation is one of the first to capture coal-seam gas from mine ventilation air and gas drainage systems. Coal- seam gas contains 40% to 60% methane, which fluctuates constantly. The system is expected to convert 578,000 m3/d (20.4 million cu ft/d) of coal-seam gas to 94 MW. It will also reduce greenhouse gas emissions by 3.5 Mt/a (3.8 million stpy) of CO, equivalent emissions. The Appin and Tower mines each produce 2 Mtla (2.2 million stpy) of clean coking coal. They operate around the clock with about 400 workers per site. The mines are owned by BHP Steel, Collieries Division, which will share the revenues from energy sales. The Appin Power Partnership consists of EDL and Lend Lease Development Corp.

Jan 1, 1997

By Pierre M. Matheron

TRANSMANCHE-LINK is responsible for designing, developing and implementing the project for a fixed link under the English Channel, comprising two running tunnels of diameter 7.6 metres and a service tunnel of diameter 4.8 metres. The three tunnels will all be 50 km long, with 37 km bored through chalk marl at a depth of 40 metres under the sea bed. The tunnels will be driven from both sides of the channel from intermediate addits above the coastline on either side with a 55 m access shaft at Sangatte in France and two "descenderies" or inclined tunnels addits and a shaft at Shakespeare Cliff on the English side. A total of eleven tunnel boring machines will drive the 150 km of tunnels. The major part of the tunnel linings will be built of precast reinforced concrete segments, and two plants have been specially built to produce the necessary 725,000 segments. Seven million cubic metres will be evacuated on wagons along the tunnels and then lifted by belt conveyor on the English side, and by hydraulic mucking from the bottom on the French side. Preliminary work started early in 1987 with manufacture of the first boring machines, construction of five precasting plants, boring of the Sangatte shaft in preparation of the Shakespeare Cliff entrances. The principal project dates are :

Jan 1, 1987

By R. W. Seedsman

Mandalong Mine was originally planned to operate with panel widths of 250 m and a predicted surface subsidence in excess of 3 m. The consent conditions applied by the NSW government on this mine plan were very tight and, following a change in ownership, were considered by the new operator to present a number of unacceptable business risks An acceptable risk profile for the mine layout restricted surface deformations to less than 500 mm vertical subsidence, less than 7 mm/m tilt, and less than 5 mm/m strain. Empirical subsidence prediction methods indicated that it would be necessary to reduce extraction panel widths of 80 m - an uneconomic option. The application of a number of rock mechanics concepts identified that the local overburden geology could be exploited such that panel widths of up to 175 m could be possible. The 125 m width was selected as a low-risk introduction of this new subsidence prediction method. The extraction of the first 2 longwall panels has demonstrated the validity of the prediction subsidence method and has provided the opportunity to refine the selection of key input parameters. The impact of mining through a zone of thrust faults was successfully predicted. The mine is now planning the introduction of 160 m wide panels, and will review the associated subsidence impacts prior to any further increases in width.

Jan 1, 2006

By T. W. Oshnock

Pulverized coal (PC) and other injectants can be injected into the blowpipes of a blast furnace to decrease coke requirements. Throughout the history of blast-furnace development, there have been many attempts at injecting PC. In the 1960's a more serious effort was made to improve pulverized coal injection (PCI) technology. However, because of the additional capital requirements and the projected near-term inexpensive cost of other injectants, very few PC1 systems were installed. When the second oil crisis occurred around 1979, the shortage and high cost of fuel oil caused blast-furnace operators to operate without oil injection. It was soon discovered that blast- furnace operation without oil was not as smooth or efficient. Experiments with PC1 quickly showed that coal was a good replacement for oil which resulted in the rapid application of PC1 in both Europe and Japan. As a result, PC1 technology for blast-furnace operation has progressed rapidly during the 1980's. This paper will describe the worldwide status of PCI, characteristics of different PC1 systems, the effect of PC1 on blast-furnace process parameters, and the economic effects of using PCI. Results from the USS Blast-Furnace Thermochemical Projection Model comparing the effects of different coal properties and the effects of other tuyere injectants such as oil and natural gas will also be described.

Jan 1, 1988

By Osvaldo Bascur, Laurent Garrigues, Nouna Kettaneh, Svante Wold

The chemical, oil, semiconductor, mining, and paper and pulp industries, as well as most other modern industries, are rapidly expanding the range of measurements used to characterize raw materials, process steps, intermediates, and final products. In addition, process variables such as temperature, pressure, and flow become more and more numerous, providing extra information on the state of the process. However, no matter how many sensors are added, the underlying sources of variations that drive the process behavior remain constant. On the other hand, the measuring frequency of these data has increased from once a day or once an hour to once, ten, or even hundred times a minute. This gives masses of data that are swelling in both directions (more variables and more observations). These data need to be properly stored, managed, and analyzed to provide diagnostics about the state of the process as well as an understanding of the relationships between different parts of the process and the product properties. Projection methods such as PCA (principal components analysis) and PLS (projection to latent structures) compress process data to informative summaries of the original variables. These can be shown on line, providing an efficient, graphically oriented suite of diagnostics regarding the "health" and performance of the process. The power of these methods is illustrated by two examples of industrial data in the mining industry.

Jan 1, 2000

By W. L. Fourney, D. C. Holloway, J. W. Dally

Introduction Improvements in the process of rock excavation by blasting involves better control of one or more phases of the fracture process immediately after detonating the ex- plosive charge. Total control of the process involves individual control of (1) The number of fracture planes. (2) The crack initiation sites. (3) The direction of crack propagation (usually radial). (4) The stress field driving the fracture front. Fracture plane control is usually accomplished today by using the smooth wall blasting method; however, investigations by the authors (1) indicate several areas where this method could be improved. These improvements include: a) generation of stress concentration factors at the location of the initiation sites; b) protection of the remaining region of the borehole wall to inhibit initiation of any cracks not associated with the fracture plane and fragmentation pattern; c) limit peak detonation pressures to avoid borehole crushing and maintain by stemming residual gas pressure in the bore- hole during the crack propagation period. This paper describes experiments con- ducted with a charge holding device fabricated from thin-wall steel tubing which was partially slit at fracture locations. The tube lined the bore-hole in laboratory tests to simulate smooth wall blasting. Results showed close control could be achieved relative to both the number and the location of the fracture initiation sites.

Jan 1, 1977

By William C. Cooley

Modern tunnel boring machines are subject to excessive cutter wear and bearing failures when used in hard and abrasive rock. In very hard rock, the high cost of cutter and bearing replacement, combined with slower excavation progress, make it more economical to drive tunnels by conventional drill and blast methods. The use of high pressure water jets to break rock provides a promising alternative. Experimental data indicate that the specific energy (the energy expended per unit volume of rock broken) decreases as the water jet pressure increases. Continuous jets are generally limited to pressures below 100,000 psi, whereas pulsed jets from a water cannon can attain much higher pressures. Therefore, the Federal Railroad Administration of the U. S. Department of Transportation has sponsored the design (Ref. 1 & 2) and the fabrication and testing (Ref. 3 & 4) of a water cannon to determine its effectiveness in rock disintegration at very high pressures. This paper reports the results of laboratory tests with pulsed jets against large rock samples at pressures of 125,000 to 650,000 psi and field tests against dolomitic limestone and granitic gneiss at pressures near 450,000 psi. Although initial tests were made with a small nozzle, operating at off-design conditions (Ref. 4), this paper only covers results with the full-size nozzle, including 55 laboratory test shots and 67 field test shots.

Jan 1, 1974

By David J. Brown, Richard C. Fountain, Marc V. Hurst

The Central Florida Phosphate District, one of the most productive phosphate districts in the world, has been mined principally within Polk and Hillsborough Counties, Florida. Recent development is extending the district southward into Hardee, Manatee, and DeSoto Counties. This area is known as the Southern Extension. The combined area of these two phosphate-bearing areas encompasses about 2,000 square miles. Structurally, the district and its Southern Extension lie at the southern end of the Ocala Arch and are flanked by the Hillsborough High to the northwest. South of this area is the South Florida Embayment. The Osceola Low lies to the east. The phosphorite within the Central Florida Phosphate District generally dips very gently (<0.1°) to the south. The boundaries of the central Florida Phosphate District are generally defined by thinning of the phosphorite due the adjacent structurally high areas to the north, west, and east, and by increased clay, CaO, and MgO content reflecting lithologic differences to the east and south. The Bone Valley Member of the Peace River Formation and reworked sediments of more recent age were the primary ore-bearing horizon in the Polk-Hillsborough County area. As those reserves are depleted, the less desirable phosphorites of the Peace River Formation are being exploited in the Southern Extension.

Jan 1, 1993