Search Documents

By Robert M. Semple, Harvey W. Parker

INTRODUCTION Two promising innovative tunnel support systems are being developed by the Civil Engineering Department of the University of Illinois. One of these is a lining which can be placed by a slipform located immediately behind and contiguous with a tunneling machine. Recent advancements in construction materials appear to provide the breakthrough required to make such a system feasible and practical. The lining material which permits this construction scheme is wire fiber reinforced concrete made with high, very early strength regulated-set cement. Parts I and II of this paper relate to this slipformed liner. Part I discusses the material and equipment required to install the liner. The "Extruded Liner System" (ELS) has been devised to place the lining. This ELS concept is briefly described and a tentative development program is outlined. In Part II, the physical properties and practical construction aspects of the liner material are discussed and a program for structural testing of 10-ft diameter prototype tunnel supports is presented. Part III contains descriptions of improvements to conventional steel-rib tunnel supports. It is shown that square tubular box sections are structurally superior to wide flange sections for complex loading conditions often encountered in rock tunnels. Analytical studies and tests on connections have been performed to evaluate their structural behavior. These are presented along with a program for comparative large-scale tests on horseshoe-shaped frames with a 10-foot span. This research is being conducted by the Department of Civil

Jan 1, 1997

By Steve Wiig

In 1987, the Rock Springs, WY district office of the US Bureau of Land Management (BLM) began to develop an automated system to store, maintain and manipulate more than 14,000 drill hole logs contained in the district's office files for various solid leasable minerals. The development of this system was based predominantly on a trial-and-error basis, with many procedural changes incorporated over time. The current Automated Drill Hole Database and Analysis System will continue to evolve with new software developments and increased personal expertise in this field. The mission of the BLM's Branch of Solid Minerals is mandated by a series of federal laws. The most important are The Mineral Leasing Act, the Federal Land Policy and Management Act, the Federal Coal Lease Amendments Act and the Surface Mining Control and Reclamation Act. Several regulations, promulgated from these laws, dictate that BLM must perform certain tasks and functions as part of its specific duties. The regulations that apply to the BLM Solid Minerals program are codified at 43 Code of Federal Regulations (CFR) 3400 for coal, and at 43 CFR 3500 for non-energy solid leasable minerals, such as sodium, phosphate and potash. Specific functions required of the Branch of Solid Minerals necessitates the use of geologic and drill hole data analyses. These functions can be divided into pre-lease and post-lease. Examples of pre-lease functions that normally require some level of drill hole data analyses include:

Jan 1, 1992

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By S. J. Jung

The most frequent causes of accidental injury and fatality are carelessness and ignorance; and the most common accidents are haulage accidents, fall, drowning, and fire. However, in this modern day and age, severe injury has become the dire consequence of an ever-increasing number of industrial and mining accidents as well as sport-, military- , etc. Mine accidents have declined dramatically in number and severity through decades of research, technology, and preventive programs. However, preventing recurrence of disasters like those of the past remains a top priority requiring constant vigilance by management, labor, and government. The goal of the present research is to investigate and identify root causes associated with types of mining accidents (victim being caught by an equipment, bodily motion, over exertion, etc) and nature of injuries such as (sprain and strains, fracture, dislocation, amputation, etc). Further, we hope to discover the impetus of the root causes occurring more and more often in this modern day of technology and quality awareness. With the different dimensions of accidents and injuries brought into the fold, there is the need for researchers and mining operators to comprehend and better still visualize significant patterns of associations among these variables of interest. We assume that, there is a high correlation between many dimensions of nature of injuries and types of accidents. This suggested a principal component analysis to reduce the dimensions for easy and amenable interpretation.

Jan 1, 2012

By J. M. Barker

The concept of global-market access through transportation efficiency is a concept whose time has come. The basis of this approach is customer satisfaction—the higher the better. But beyond what seems almost too logical is the question of how to achieve this market access. All industrial mineral exporters face stiff competition. Factors include proximity of competitive industrial minerals and substitutes, pricing pressure, political and cultural differences, currency fluctuations, communication problems, trade finance restrictions, and transportation imbalances. The following discussion will focus on transportation activities in global competitiveness, but the producer with the larger offering of services will often make the sale, not necessarily the low-cost producer (Cook, 2002). Some key concepts for global-market access are “the market concept,” just-in-time delivery, quality retention, and global customer service.

Jan 1, 2003

By Steven Schurman

Acid Rock Drainage (ARD) is one of the most serious and persistent pollution problems facing today's mining industry. ARD is formed when pyrite (FeS) is exposed to natural weathering conditions. Pyrite weathering, formally the oxidation and hydrolysis of pyrite, leads to the generation of soluble, hydrous iron sulfa-salts and the production of acid in the form of H+. The resulting effluent is water that is characterized by high levels of iron (and any other metal contained in the rock undergoing weathering) as well as high concentrations of sulfate and a low pH (acid). Rocky Mountain Remediation Services, L.L.C., has developed a patents pending Envirobond'™ product, Envirobond™ ARD, to treat acid rock drainage. Treating pyrite with Envirobond™ ARD inhibits the oxidation and hydrolysis of pyrite thus curtailing the pyrite oxidation cycle.

Jan 1, 1999

By C. H. L. Bastos

A physical and chemical characterization study was carried out on 483 kaolin samples from 2.9 km2area at the Para Pigmentos mine along the Capim river, northern Brazil. The samples obtained from cores, drilled with regular spacing of 100 m, were evaluated using grit percentage, particle size distribution (psd), brightness, leachability, magnetic response and viscosity. These parameters were correlated with each process step in the plant and also the physical and chemical properties of the ore and finished product. Cluster analysis was performed and four main groups of kaolin were identified. These were then related to their performance at the various process steps and the quality of the initial product. These groups are well defined by plotting grit X “psd” and TiO2x “psd” in scatter plots.

Jan 1, 2004

By Martin F. Grier

The Mt Todd Gold Project is located 300km to the south of Darwin in the Northern Territory of Australia. The identified resource comprises 46 million tonnes at 1. 65g/t using a 1. 0g/t cut-off ( 50 million short tonnes at 0.05oz/st). The resource is open to the north and at depth. Mineralisation comprises easterly dipping sheeted quartz/sulphide veins, typically 10 to 20 millimetres in thickness, hosted by hornsfelled greywackes. The majority of the ore body is primary ore with only 10% classified as oxide ore. Early testwork showed that the ore was not suitable for heap leaching, giving only 50% recovery at a -3mm crush size. Acceptable recoveries were obtained at a P80 of 75 micron. However, the ore is extremely hard.

Jan 1, 1992

By E. E. Bauer

Oversize boulders in mines and quarries must be broken for waste disposal or further processing of ore. Early methods involved drilling and "shooting" or using a drop ball of sufficient weight to accomplish the purpose. The first "high-energy" hammers for breaking concrete or boulders were pneumatically operated. Blow energy was limited by valving and air pressure. However, smaller boulders of lower compressive strength could be broken. A hydraulic excavator-backhoe type machine was required for either a drop ball or hammer. Standard practice was to break oversize boulders in the pit before hauling to the grizzly or crusher. Generally, quarry boulders were not valuable enough for further processing. Quarry roads were lined with oversize boulders. As safety requirements were advanced, "drill and blast" for boulders was ruled out.

Jan 1, 1994

By F. X. Meagher

Vertical slot raise driving from bottom up has always been a hazardous, inefficient, high cost operation. The introduction of the Simba 5 drill rig has enabled this type of raise to be drilled accurately from the top down and to be blasted in stages from the bottom up. Safety, high efficiency and low cost were the main criteria in opting for this method. Drop raises with the Simba 5 at Geco have been successfully drilled and blasted up to 115 feet, and this is close to the maximum length of raise that can be drilled and blasted efficiently with Simba 5. A look into the future would indicate a rig capable of drilling up to 200 foot raises with the same accuracy of Simba 5 to 115 feet.

Jan 1, 1974

By T. Yegulalp, K. S. Lackner

Zero emission coal plants capture their own CO2 emissions. Since they have no smoke stack, they emit no pollutants to the air. Zero emission plants circulate a gas stream, to which fresh fuel is added and from which spent fuel and impurities are removed as solids or liquids. Coal is gasified via hydrogenation, steam reforming or CO2 gasification (Boudouard reaction). The gas is oxidized in a fuel cell and the resultant water and CO2 are partially removed before returning the remaining gas to the gasifier. The high conversion efficiency of zero emission power plants, which exceeds 70% even in realistic designs, stems from combining fuel cells with careful heat management. The paper generalizes the concepts and outlines the thermodynamic basis of zero emission power plants.

Jan 1, 2004

By Michael Jatczak, Joseph A. Sopko

Ground Freezing was used for excavation support and groundwater control of a 12.8m (42-foot) diameter, 61m (200-foot) deep drop shaft for the South Bay Ocean Outfall Tunnel in San Diego, California. Approximately half way through the excavation, excessive groundwater inflows from the base of the shaft resulted in suspension of excavation and evaluation of the frozen earth wall. This paper discusses the forensic methods used to identify the zone where groundwater intrusion occurred and the methods associated with evaluating zones of high groundwater velocity. The use of remedial grouting and localized liquid nitrogen injection are discussed and evaluated. Concepts of frozen shaft design are discussed, including a new method for permitting the launch of the Tunnel Boring Machine through the frozen earth wall and associated freeze pipes.

Jan 1, 1999

By Roshan B. Bhappu

The extraction of gemstones, except for diamonds, continues to be a more or less handpicking type operation all over the world. However, considering the physical properties of gemstones such as density (sp.gr.), color, size, shape, luster, brilliance, reflection of light and the like in contrast to the relatively ‘dull’ physical characterization of the associated gangue minerals, it should be feasible to recover several gemstones using modern mineral processing techniques. This paper illustrates the unique physical characterization of several gemstones and suggests appropriate mineral processing techniques that could be used to recover these precious stones. Special emphasis is placed on the versatility of the Heavy Media Separation (HMS) process for processing of the gemstones. Finally, a few examples of commercially viable operations involved in the recovery of emeralds and rubies are presented.

Jan 1, 2005

By B. K. Kejriwal, A. K. Ghose

Under specific geological environment, the full extraction of a coal seam is not possible either because of its extraordinary thickness or the presence of surface structures and bodies of water or because of the conditions prevailing in upper seams. Not uncommonly, therefore, for working such seams, pillars of coal are left for the permanent support of the overburden, and voids around the pillars are filled with sand to strengthen the pillars and prevent their deterioration with time. However, the paucity of river sand has focussed attention on the need for alternate strategies including trials with partial filling of the voids. This study has sought to examine in the laboratory the effects of partial and complete filling on the ultimate load bearing capacity and post-failure behaviour of small, tall pillars using artificial material.

Jan 1, 1986

By J. Launay

In order to control and dispatch the sewage water coming from 3 tunnels toward 2 downstream sewage tunnels, a large cavern has been excavated in a suburb of PARIS. Located at a depth of 47,00 m, it has been excavated using the NATM procedure through swelling clay, weathered sandstone, and marl and chalk. It is 16,50 m high, 12,40 m wide and 60, 00 m long, with an elliptical cross-section and its two ends are egg-shapped. The final lining of the cavern is composed of 30 to 40 cm of shotcrete, steel ribs and passive anchor bars. The excavation stages and related movements were surveyed by extensometers, pressure cells and convergence devices. The design, method of construction of the cavern and the results of the measurements made are commented.

Jan 1, 1989

By P. G. Semple, K. W. Major, R. M. Nendick

As free milling oxide gold ore reserves are depleted, more mining companies are having to evaluate the available alternatives for treating refractory deposits. The selection of a treatment process can be very difficult; and, despite the claims of their respective proponents, there is no one process that will continuously prove superior. Selection of the optimum process for an individual deposit is contingent on the size of the deposit, the grade of the deposit and the refractory nature of the ore. Since extensive metallurgical test programs are usually required to determine the optimum extraction process, an inappropriate initial selection may prove costly and time consuming. This paper discusses the steps involved in evaluating a refractory ore in order to expedite the evaluation of the required process through the feasibility study stage.

Jan 1, 1990

By Kotaro Ohga, Gota DEGUCHI, Kiyoshi HGUCHI

The situation of Japanes coal mine is in the severe enviroment, because the policy on coal mining has changed. Every year one or two coal mines will be foced to close. To continue the production of coal, we have to reduce the cost of production. Therefore, the mining by longwall method which is more than 250m was attempted at Taiheiyou Coal Mine to reduce the cost and this mining method have had successful results. To get successful results by this mining method, the controlling and prediction of gas emission from the longwall panel will be most important things. In this paper, the comparison of the predicted gas emission from the mining panel based on the measured gas content by using new device with the observed results is described.

Jan 1, 1993

By C. L. Karr, E. J. Gentry

Researchers at the U. S. Bureau of Mines have developed a control algorithm to efficiently manipulate chaotic systems. The control, based on both fuzzy logic and genetic algorithms, prescribes actions that drive the chaotic system to acceptable regions of state space. The use of fuzzy logic enables a person who has limited experience with a chaotic system to establish a set of rules for manipulating the problem environment, and a set of membership functions that define terms used in the rule-set. Genetic algorithms are search algorithms based on natural genetics, and are used in the control algorithm to select membership functions that provide for a suitable level of control. The Bureau-developed algorithm controls the computer simulation of a ball bouncing on an oscillating table, a system that exhibits chaotic behavior.

Jan 1, 1993

By Yuusaku Tominaga, Sukumar Bandopadhyay

A power-series trend curve of elapsed time was estimated by using time series data of measured concentrations of carbon monoxide in the Taiheiyo coal mine, Hokkaido, Japan. The difference between the moving average concentration data and the estimated data from the trend curve showed linear correlation when plotted on a normal probability paper and a correlation coefficient value of 0.99. It is concluded that the estimate of carbon monoxide concentration using moving average values of concentrations compares very well with the results obtained from the trend curve within the three-sigma (standard deviation) range of the distribution. Thus, it is believed the results can be used to monitor and detect abnormal ventilation conditions in a ventilation network such as the occurrence of spontaneous combustion at an early stage.

Jan 1, 2002

By I. de Jong, G. Van Weert

Silver cyanide adsorbs extremely well on activated carbons. This suggests that the addition of soluble silver salts to trace cyanide containing waste streams should allow efficient cyanide removal with active carbon. Silver losses, however, would make this method expensive and also objectionable, since silver has biocidal effects. When silver impregnated carbon is used, these problems are overcome. Test work has shown that such silver remains on or in the active carbon, that cyanide concentrations can be reduced to the level of detection (< 5 ppb) and that the silver impregnated carbon can be reactivated with equipment similar to that now in use at gold milling operations. Initial results on the type of carbon, the impregnation procedure and the level of silver, and the effect of repeated regeneration are discussed.

Jan 1, 1992