Search Documents

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

By Carla Da Corte, Kagisego Letsoalo, Ashma Singh

Banded Iron Formations (BIF) are sedimentary rock formations ranging in age from 0.8 to 3.8 billion years and consist of alternating layers of silica and iron. The thickness of the alternating layers varies between and within deposits, with this lithology forming approximately two-thirds of South Africa’s future low-grade hematite resources. The production costs for South African iron ore producers are approximately double that of the largest iron ore producers, namely, Brazil and Australia. This in conjunction with volatile commodity prices, necessitated a cost-sensitive beneficiation strategy for low-grade hematite to sustain the industry and extend life of mine. A BIF sample grading at 44% Fe and comprising predominantly of hematite and quartz with minor amounts of magnetite and goethite was subjected to three fines gravity processing routes to establish the amenability of this sample to beneficiation. To provide flexibility for iron ore producers who still have high-grade resources available, two product grades were considered, namely a 60% Fe product for further blending or a 63% Fe product for direct sales.

May 12, 2023

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

By Timothy G. Shuttleworth

In the late1970s, mineral processing plants producing copper sulfide concentrates and oxide leaching feedstocks went online with operating tonnages that exceeded traditional installations. This created a need for larger capacity belt conveyors and apron feeders. Apron feeders are slow moving, heavily loaded conveyors that feed a deep bed of ore from a bulk holding location (a bunker) as a controlled stream, often into a large capacity crusher. Apron feeders use sprockets and caterpillars, while belt feeders use rubber belts with motorized head pulleys to convey the material. The damaging of belts and clogging of transfer points from tramp iron required larger magnetic separators and the removal of tramp metal cannot prevent these serious problems. Corrective action at this location is important for two reasons: Removing tramp iron early in the ore stream protects downstream equipment from potential costly damage. Installing apron feeder magnets before the primary large capacity crusher means that secondary and tertiary crushing steps (made up of multiple parallel units) operate more efficiently, since tramp metal is removed at the onset.

Jan 1, 2011

By S. C. Termes

As part of an effort to provide basic data on the fundamental scientific and engineering principles of minerals beneficiation, the Bureau of Mines is conducting research on the flocculation of mineral fines. This paper presents results of studies using crosslinked starches containing carboxyl, diethanolamine, iminodiacetic acid, and xanthate groups to flocculate hematite, goethite, chromite, manganrte, pyrolusite, cuprite, and cassiterite fines. The carboxyl and xanthate derivatives flocculated all minerals except cassiterite; the latter was flocculated by only the diethanolamine derivative. The iminodiacetic acid derivative flocculated hematite, goethite, chromite, cuprite, and pryolusite fines. Zeta potential measurements were made to help define the reaction mechanism responsible for flocculation. These measurements indicate that electrostatic attraction probably is not involved, except possibly in the case of the diethano lamine derivative. The separation of hematite from quartz by selective flocculation with chelating cross- linked starches under two pH conditions and with two dispersing agents is described. Best recoveries and grades were found when either the carboxyl or xanthate derivatives was added at the natural pH of the pulp in the absence of a dupersing agent.

Jan 1, 1983

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By Edward H. Peplow

Mr. Chairman; honored guests; ladies and gentlemen: The subject assigned me today by your committee, according to the program, is "the mineral industry and the public land law I have preferred to title the talk, "you can't mine here", for that is the essence of the message we, as an industry, have been getting from so many agencies of the federal government for so long. And, unfortunately, we can expect to hear the same message even louder and clearer -- with increasing frequency in future, unless. Every segment of the industry devotes the necessary time, energy and creative thought to combat successfully the forces that are writing and broadcasting that message. I said that agencies of the federal government are sending the message --- and this, of course, is true, the forest service, for example, and some bureaus of the department of the interior as well as others have appeared in recent years to be abiding by a policy designed to block mineral entry to as much of the public lands as possible and to wipe out existing mining claims.

Jan 1, 1967

By Firat Atalay

Estimating the spatial distribution of ore grade is one of the most critical steps to proceed with an investment decision on a deposit. Kriging is the most widely used method to estimate the ore grade, but alternative techniques are being developed. Machine learning algorithms can be used as alternative methods to classical kriging. In this paper, the iron (Fe) grade of a deposit is estimated with the XGBoost algorithm, and the results are compared with kriging estimation results. For the estimations, samples collected from drillholes were used. Due to the different natures of the estimation methods, different steps were taken to perform the estimations. The results show that XGBoost produced higher-range estimates, which is a desired result in ore grade estimation, and the minimum and maximum of the estimates were lower and higher than the kriging estimates, respectively. However, like kriging, the estimation results were smoother than composites, and the variance of the XGBoost estimates was lower than the variance of composites. This means that even though estimation with XGBoost mitigates the smoothing effect, the estimation results suffer from smoothing like kriging.

Dec 1, 2024

By M. P. Valoski

In the United States, the occurrence of underground mine fires/explosions continue to decrease; however, they pose great danger to the miners and any subsequent mine rescue teams and/or fire brigades. Tragically, 19 coal miners lost their lives in 2006 at fires or explosions. Fires/explosions can devastate a mine and cause its permanent closure. It is vitally important to obtain accurate information on the gas content (concentration and composition) of the mine atmosphere after the event so that appropriate action can be instituted to rescue any trapped miners while not exposing the mine rescue teams to unnecessary hazards. Additionally, the fire fighting techniques (spraying water, sealing, etc.) will be dictated by the gas content. Finally, the gas content will determine when it is safe to recover the mine. The gas content of the air can be determined using detector tubes, handheld instruments, portable instruments, or gas chromatographs. No single instrument is suitable for all analyses. Each type of instrument has its advantages and disadvantages. This paper discusses these attributes.

Jan 1, 2010

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By J. R. Mackie

Reserve Mining Company, the first large-scale taconite pellet producer in the United States, mines it's crude ore at the Peter Mitchell Mire located on the eastern end of the Mesabi Iron Range near Babbitt, MN. The ore is processed at Reserve's beneficiation plant on the north shore of lake Superior at Silver Bay, M. The mine and plant are linked by a 47 mile, double track, railroad which is owned and operated by Reserve. (see Fig 1). At rated capacity, the mine can produce 33 million It/yr of crude ore, 15 million It/yr of waste rock and 1.0 - 1.4 million yd3/yr of glacial till stripping. Haulage of all mined material is accomplished using trucks. Ore is transported by tractor-trailer side dump units which have capacitys ranging from 83 to 110 long tons. Waste rock and glacial till is transported in end dump units of 50 to 120 LT capacity. Loading is accomplished by 11/13 yd3 power shovels and 7/10 yd3 front-end loaders.

Jan 1, 1985

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By James W. White

From Modular's first truck-dispatching system for Phelps Dodge Corporation in 1979 to today's alliance between Modular and Komatsu, Ltd., innovation has been Modular's main product. This paper describes the growth of a mining products supplier and the philosophy and decisions behind that growth.

Jan 1, 1998

By Harry Sutcliffe, Francis M. Keville

The paper describes the, impact of the geotechnical exploration program on the line and grade of the tunnels and the shaft configuration on the Red Line Extension N.W. in Cambridge and Somerville, Massachusetts, and comments on several aspects of the implementation of the project.

Jan 1, 1983

By G. E. Burrer, D. Malhotra, T. E. Irwin, S. Johnson

Climax byproduct-plant tailing assayed 0.019% WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The methodology used in the study and the results of this investigation are discussed.

Jan 1, 1987

By Francis W. Brown, Philip R. Hunt, Douglas N. Halbe

Refractory arsenopyrite ore from Western Mining Corporation's Lancefield deposit in Western Australia is treated by fluosolids roasting of a flotation concentrate followed by cyanidation of calcine and flotation tailings. The project development is reviewed from original testwork through circuit design, operating experience, and subsequent expansion.

Jan 1, 1990

By Claude M. Moreland

It is common practice when thermally drying coal from wet coal preparation facilities that the coarse +0.5mm fractions and fine fractions (-0.5mm) are combined and fed to a thermal dryer. There are very good reasons for this concept. The coal feed is much easier to handle in this condition for it is not as likely to stick inside the dryer or hang up in the material handling equipment, and is easier to feed and discharge. However, it is generally only the -0.5mm fines that really need to be dried. The +9.5m fraction of the cleaned coal will leave the dewatering screens, or drain and rinse screens, at an acceptable surface moisture, probably 5 or 5 ½ percent. The 9.5m x 0.5mm mesh fraction can be centrifuged to about 8 percent. The -0.5m fines can range from 18 to 22 percent or more, depending upon the type of equipment employed to dewater, and upon the size distribution within this size range.

Jan 1, 1982

By V. D. Hanson

When maintenance of a plant or operation is under discussion immediately three "M's", all in short supply, are brought to mind - money, men and markets. This paper will present what currently is being done at our plants and its effect on the 3 "M's". Examination of coal realization figures (F.O.B. Mine) from 1945 to the present reveals the fact that open and free competition can and will meet market conditions. The industry, without benefit of advantages afforded tax and transportation wise to oil and gas, remains the backbone of the energy market of United States. Figure No. 1 shows the realization figures from 1945 through 1962 compared to the hourly earnings. Note that through 1945 to 1948 F.O.B. prices increased $1.93 per ton while hourly earnings increased $.66 per hour. Since 1948 (with the ex¬ception of 1957) F.O.B. prices have declined $.45/ton, while hourly earnings have increased $1.23 per hour. Basically the maintenance men possibly represent the highest increment rate in the overall hourly earning.

Jan 1, 1963

By Thomas Bubanovich

Engineers at the Freeman United Coal Min¬ing Company, located in West Frankfort, Illinois, have been using a computerized production planning and maintenance reporting system, which have been designed exclusively for underground coal mining. This paper will explain a dynamic graphical simulation and computerized time study system that has been used to design and evaluate underground production systems for optimizing productivity. Also with the aid of customized software, detailed records on changeable components of underground equipment, including the vendor's name, date installed, operating and maintenance hours, etc., have helped Management to select the best available components for their equipment. The MPASS System, Mine Performance Analysis Simulation System, developed through a cooperative agreement with Freeman United, Ketron Inc., and the U. S. Department of Energy utilizes new methods to analyze and design production systems in underground coal mines. The MPASS System is a menu-driven user oriented system of interactive computer programs, which form five major subsystems. The subsystems: 1. Simulation 2. Time Study 3. Mine Background Reports 4. File Maintenance Subsystem 5. Statistical Analysis Subsystem

Jan 1, 1987

By Frank McKinley

This paper discusses the basic requirements covering the area between the initial discovery of a deposit and a decision as to whether or not the deposit will support an economically sound mining venture. The procedure for gaining the necessary information and the sequence of steps is in .some respects parallel to gaining like information on deposits other than the sand type. For the sake of simplicity the stages and sequence are presented as follow: first, the initial reconnaissance drilling; second, the exploration drilling to permit initial ore body estimates; third, metallurgical testing; fourth, the estimate of plant and operating costs; and last, the economic balance. The objective of the reconnaissance drilling is to collect sufficient information to reach a decision as to the advisability of further exploration or the abandonment of the area. This initial phase will comprise, in addition to some drilling, a thorough reconnaissance of the area, a study of the best geological and topographic maps of the region, and a study of any literature available, all under the guidance of a geologist.

Jan 1, 1958