Search Documents

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By T. J. Close

The Silver Peak Range North Wilderness Study Area was deleted from the list of US Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the US Bureau of Mines mineral investigation of the wilderness study area which found indications of precious- and base-metal-resources. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Bureau examined 13 mineralized sites, most of which were previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak mining district to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz and calcite with gold, silver, and base-metals. At the surface, these veins are poorly defined. Exposures of the more than forty veins examined were as thick as 17 ft and as long as 1000 ft. Samples from these veins contained significant amounts of precious- and base-metals-as much as 0.02 oz per ton gold, 2.1 oz per ton silver, 1.0% copper, 2.6% lead and 0.4 % zinc. No vein large enough or of high enough grade to be classified a mineral resource was disclosed by the sample data. However, most do have indications of precious- and base-metal-resources at depth. Subsurface exploration of some of the veins is recommended.

Jan 1, 1995

By Malcolm J. McPherson

Observations of environmental parameters in mines have traditionally been made by means of hand-held instruments, these being employed as a basis to ensure that atmospheric conditions in the mine remain within limits commensurate with safety, to safeguard the health of personnel, and to ensure that statutory requirements are met. Thus, starting from the first flame safety lamps of the early nineteenth century, numerous portable instruments have been devised over the years to indicate levels of dust, temperature, humidity, and concentrations of gases including oxygen, methane, and carbon monoxide. Similarly, portable instruments have been used to measure air velocity and pressure. For routine monitoring purposes, hand-held equipment suffers from many disadvantages. Readings are intermittent, often with long delays between successive observations, making short-term trend analysis impossible. Portable instruments are more liable to damage; they are labor intensive and provide a very limited amount of information either for control or planning purposes. The 1960's and 1970's have seen an accelerated development of mine environmental monitoring equipment. Alarm methanometers to give localized audiovisual signals became more common. These were followed by a variety of instruments which gave local, then local/remote continuous records, particularly of methane concentration and airflow. More sophisticated transducers and transmission systems were developed allowing further parameters to be monitored. This led to a proliferation of paper strip and chart recorders which had to be maintained and inspected regularly for trends and abnormalities.

Jan 1, 1979

By A. W. Khair

This paper presents an analysis of surface subsidence characteristics in room and pillar mining using physical models and laser holographic interferometry (holometry). The analysis included the effect of various geometric parameters and different overburden materials (sand and gelatin) and resulted in the formulation of a more realistic model material for laboratory simulation of typical geologic overburden. Previous work using this technique involved the use of sand to model over- burden and detailed results are presented elsewhere (1). The main emphasis of this work was to develop a gelatin based mixture which would provide a better model. Initial work during the development of this model included testing various ingredients and monitoring the time dependent characteristics of the model, such as the surface penetration resistance. This value indicated changing deformability/ridgidity of the model with time. Once several models had been developed, holometry techniques were applied. Initial tests showed that the stiffness of gelatin created a bridging effect over the mine models, thus restricting deformation. At this point, a 0.5 inch (1.27 cm.) layer of sand was placed directly over the mine model with the gelatin mixture on top. The approach was to model different zones of overburden movement that exist as an extraction occurs (2). The sand would represent the caved and fractured zones which occur above the excavated area. The gelatin models the continuously deformed zone which occurs between the fractured zone and the surface. Holometry techniques applied to this model yielded successful results.

Jan 1, 1986

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By A. Iordanidis

Mining activities have recently been taken place in Vourinos mountain, northern Greece, exploiting the so-called ?olivinite?. A representative sample was collected from this mining area. Mineralogical analysis was conducted using X-Ray powder Diffraction (XRD). A thin section was prepared and analyzed under optical microscope. X-Ray Fluorescence (XRF) was employed for the chemical analyses of major, mi-nor and trace elements. Environmental Scanning Electron Microscopy coupled with energy dispersive x-ray analysis system (ESEM-EDX) was also applied for the characterization of the sample. Forsterite (Mg-rich olivine) and enstatite (Mg-rich orthopyroxene) were the main mineral phases determined by XRD, with a 56% and 44% content respectively. Trace amounts of chromite spinels were also determined. Based on this characterization, the industrial rock proved to be a hartzburgite (a type of peridotite in petrological terms). Optical microscopy and ESEM-EDX provided similar observations and confirmed the above-mentioned results. XRF revealed a composition of 43.31 MgO, 44.25 SiO2, 9.98 Fe2O3, 1.40 CaO, 0.67 Al2O3, 0.22 MnO, 0.01 TiO2 and negligible amount of LOI (<0.1%). Trace elements with high concentrations were Cr (2678 ppm) and Ni (2044 ppm). The comprehensive characterization of this mining product suggested the suitability for various uses, such as refractories, foundry and slag conditioner. Additional experiments are being carried out for environmental applications, e.g. wastewater treatment.

Jan 1, 2006

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division&apos;s newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

By R. R. Klimpel

This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: 1) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.

Jan 1, 1996

By J. M. Pachter

Property sales and acquisition are prominent features of today&apos;s coal industry. Before selling or buying a site, a company must know the property&apos;s economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property&apos;s environmental liabilities and costs were omitted. Short-term and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1986

By N. Arbiter

Evidence for the floatability of sulphide minerals without collector is analyzed and it is shown that results obtained with ores, in contrast to those with single minerals or mineral mixtures, depend on many additional variables, some identified and others not. Because of the prevailing low levels and costs of collectors for most sulphide ores, it is unlikely that collectorless flotation will have commercial applications, so that continued research on the subject may be justifiable on theoretical but not on practical grounds.

Jan 1, 1993

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By J. J. Webb

At Kerr-McGee&apos;s Galatia Mine in southern Illinois, the need for safe and efficient longwall moves prompted a detailed planning effort. Galatia Mine operates two longwalls on separate coal seams with different geologic conditions. An overview of the longwall move planning as related to manpower training, roof control, ventilation, transportation, equipment recovery and setup will be discussed. The impressive safety record achieved during each of the longwall moves at Galatia Mine verifies that health and safety planning does play a major role.

Jan 1, 1994

By D. A. Smith

The successful integration of overburden casting techniques into the mine production cycle can be an extremely cost effective use of explosives. The entire mining cycle revolves around the cast blasting and to be successful requires a great deal of planning and cooperation. Several operations of Cyprus Coal Company in the Appalachian coal fields have successfully integrated blast casting into their mine plan. This paper will detail the parameters and necessary controls to integrate an overburden casting program into a surface coal operation.

Jan 1, 1993

By J. G. Groppo

Laboratory settling and filtration testing was conducted on wet processed fly ash in order to determine the applicability of conventional dewatering techniques to reduce the moisture content prior to drying. Settling tests showed that acceptable clarity (<1.5 g/l suspended solids) could be achieved after as little as 6 minutes of settling. After settling to a consistency of 40 weight % solids, continuous laboratory vacuum filtration testing produced a cake containing below 20% moisture with throughput exceeding 150 lb/ft2/hr.

Jan 1, 1997

By William L. Rose

Production scheduling is an integral part of intermediate- and long-range open-pit mine planning, affecting equipment selection, manpower requirements and project economics. The development of mining phases, or pushbacks, is discussed in conjunction with generating the best spatial extraction sequence. An approach to scheduling production from these mining phases is then described. Using computers and a production scheduling algorithm, the impact of cutoff grade and advanced stripping policies can be evaluated through sensitivity studies to maximize the return on project investments.

Jan 1, 1985

By E. Fahrenkrog

An intelligent supervisor developed using expert system tools and applied to a crushing plant is presented in this paper. The structure of this supervisor, based on a model of a human operator, consists of a Knowledge base containing a qualitative model of the process, and a Rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of systems to supervise the automatic operation of a plant.

Jan 1, 1989

By Colin D. Jardine

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. A recent application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by the use of a "building block" approach to design and equipment selection. Details of this approach and the results obtained are described.

Jan 1, 1982

By R. F. Davis

The evaluation and selection of coals for producing metallurgical coke is indeed a com- plex process simply because coal is a complex and variable substance which is sensitive to how it is treated from the time it is mined until it is transformed into coke. A review of the the more common evaluation tests made on coal and how the test results are applied in commercial practice. Parameters used to select coal blends for wet and preheated charges should also be of interest.

Jan 1, 1980

By A. MacG. Robertson

Where weak rock zones are encountered in the slopes of an open pit, they may control pit wall stability. Back analysis of slopes involving failure through weak rock enables an estimate to be made of the weak rock strength. A system of consistent rock mass classification is described which enables the weak rock mass material to be described and classified from drill hole core. Correlation with back analysis determined strength allows strength estimates to be assigned to each rock mass classification.

Jan 1, 1988