Search Documents

By M. J. Hrebar

This paper reviews large dozer stripping techniques and presents results of two field studies. The first is a seven-shift study of a contour block stripping operation where a Caterpillar DII is used as the primary stripping equipment. The second is a two-shift study of two Cat DIIs dozing blast cast material ahead of a dragline operation. Surveys and continuous time studies were used to determine production rates and as a basis for forecasting unit stripping costs in both cases.

Jan 1, 1994

By David W. Lillie, Pier A. Abetti

This paper reports on a study of the impact of fast growing new technologies on the market for copper over the next 15 to 20 years. The greatest threat is clearly the inroads of fiber optics on the traditional market for copper in communication cable. Opportunity areas identified include heat pumps, solar power and heat, desalination, electric vehicles and others. The overall impact of new technologies on copper is expected to be modestly positive if adequately encouraged by effective R&D.

Jan 1, 1986

By J. B. Yianatos, G. S. Dobby, J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

The question is posed as to why columns typically have a collection zone 10 m high (H) by 1 m in diameter (D). Three geometry dependent factors are considered: degree of mixing, Np; volumetric bias rate, B; and volumetric gas rate, G. Increasing H:D decreased Np and B, which improves performance but decreases G, which causes the column to approach overloading. Taking typical column operating conditions, it is concluded that a collection zone H:D of 10:l is a reasonable compromise.

Jan 1, 1987

By Chester R. Harris

With the passage of the Occupational Safety and Health Act (OSHA) on December 29, 1970 and the formation and growth of the OSHA Agency it spawned, public consciousness of occupational safety was raised. It became accepted that employees had the right to "a safe and healthful workplace". With the possibility of OSHA inspections, employ ers (particularly those with large workforces) began to give serious con sideration to engineering controls, safety programs, and training in a more uniform manner than previously.

Jan 1, 1991

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering; nevertheless, standardized methodologies for their computer implementation do not exist. In meeting this need, this paper introduces the concept of a process software model, or more specifically an object-oriented software model, and presents a detailed methodology for its development involving software model specification and development. These software models provide a formal basis for the subsequent design and construction of software objects corresponding to the real world process objects.

Jan 1, 1995

By Mark W. Springett

The sampling of precious metal deposits entails inherent problems due to the low mineral abundances, high mineral specific gravities, skewed grade distributions and wide ranges of mineral particle sizes. Sampling practices and precautions are discussed with particular attention to each of the tripartite stages of sampling - sample acquisition, sample preparation and sample assaying. Practical examples of approaches to the sampling problem are given and some examples of significant sources of error are provided from gold and silver deposits in North America.

Jan 1, 1992

By J. M. Pachter

Property sales and acquisition are prominent features of today's coal industry. Before selling or buying a site, a company must know the property's economic net worth. Any evaluation of economic net worth would be inadequate if determinations of a property's environmental liabilities and costs were omitted. Short-and long-term costs can result from liabilities related to reclamation, water treatment, subsidence, and hazardous waste disposal. A structured, interdisciplinary approach can aid in the delineation, summation, and scheduling of these costs and liabilities.

Jan 1, 1987

By Kevin L. Purdy

Chemical dewatering aids for mineral slurries generally fall into two classes: surfactants and flocculants, which can be used separately or together. Current industrial use of both types of reagents is summarized for sulfide and non-metallic minerals, as well as uranium and gold leach residues and coal refuse. Laboratory testing for reagent selection is briefly discussed along with reagent preparation. Chemical properties of the reagents which affect the suitability for particular applications are analyzed. [BLANK PAGES - Are in the original]

Jan 1, 1986

By Frederick W. DeVries, J. Brent Hiskey

Cyanide has been recognized for about a century as the most effective reagent for processing gold ores. Cyanide leaching has been adapted to various metallurgical settings and continues to be improved. However, in recent years attention has been directed to alternative lixiviants for treating refractory ores and concentrates, and to the development of less environmentally controversial substitutes for cyanide. This paper reviews some of the reagents considered as alternatives to cyanide and focuses on environmental implications for using these newer reagents.

Jan 1, 1992

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts (CCB). Alkaline combustion byproducts are gaining increasing usage for acid mine drainage (AMD) mitigation as research leads to a better understanding of their beneficial applications. Since January 1997, Mettiki Coal has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit No. 3 wet limestone scrubber into abandoned portions of the active Mettiki Mine.

Jan 1, 1998

By Anis Farah, Khosrow Aref

Pull-out tests were conducted on cable bolts grouted with concrete, and cement paste. The influence of several parameters on the performance of these cables were studied under loading rates varying from very slow to relatively fast. These parameters include water-cement ratio, cable surface conditions, curing time and embedded length. In addition to being more economical, the results indicate that cables grouted with concrete have higher ductility and ultimate bond strength as compared to those with cement paste only.

Jan 1, 1986

By Charles A. Ramsey, Kathleen S. Smith, Philip L. Hageman

We developed a statistically based strategy for sampling the surficial material of mine-waste dumps for use in screening and prioritizing historic dumps on abandoned mine lands. This sampling strategy entails the collection of a representative composite sample from individual dumps and allows for regional or watershed-based assessments. One 30-inment dump-composite sample collected using this sampling strategy contains as much information, relative to average value, as 30 individual grab samples at 1/30 of the analytical cost.

Jan 1, 2000

By Tim Wolf

The author has seen an increased use of shaft-mounted, right angle drive assemblies. These designs use the pulley shaft as its 'foundation" and can create significant overhung loads. To reliably perform, the pulley and shaft must be designed for these special requirements. This paper will focus on the development of overhung loads and their design effects. Special considerations to maximize performance will be presented and comparisons with other drive options will be made. Experience in heavy mining applications will be used throughout.

Jan 1, 2000

By B Faulkner, M. Weinecke

In 1997, Sveciala began a program to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed shortcomings that were process related or mechanical related, while some of the approaches emphasized he production of low-value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot-plant development and commercial plant design of such a process.

Jan 1, 2002

By M. Dayne Aldridge

A description is given of an experimental ventilation control system designed, built, and tested by WVU under United States Bureau of Mines sponsorship. A description is given of the control, system used and the mine-wide microcomputer-based ventilation monitoring system used with it. Test results of experiments conducted with this system at Eastern Associated Coal Corporation's Federal No. 2 underground coal mine are presented. In addition, a brief description is given of a new microprocessor based system presently being tested.

Jan 1, 1980

By R. G. Reddy

Chemical and structural changes occurring during the roasting of refractory gold ores were investigated. Effect of temperature on oxidation behavior of ores was analyzed using TGA, DTA and X-ray diffraction methods. The experimental results showed that the carbon in the ore has to be oxidized to a minimum value before any appreciable oxidation of sulfur occurs. Oxidation rates as a function of temperature were calculated. Optimum conditions under which a successful roasting of the refractory gold ores can be obtained are discussed.

Jan 1, 1990

By W. J. Wuest, M. J. DeMarco

The US Bureau of Mines (USBM) recently developed a rock-mass classification system for evaluating the structural competency of bedded roof strata. The system is called the coal-mine roof rating (CMRR), When compiled with the companion Lotus 1-2-3 spreadsheet, CMRR data are a useful tool with applications to longwall gate-road pillar design, safety-hazard mapping and artificial roof-support analysis. This paper gives a review of some applications under actual conditions found in current US mining operations.

Jan 1, 1997

By Rudrajit Mitra, Wesley B. Johnson, Erik C. Westman

The ability to understand stress redistribution within a mine allows greater extraction efficiency with reduced safety concerns. Stress redistribution has been examined at the laboratory scale using ultrasonic tomography and numerical modeling using PFC3D. A data acquisition system was built to obtain tomograms as samples are loaded in uniaxial compression. Limestone samples were loaded to failure. Three-dimensional tomograms of the samples correlate to various stress distributions. The tomograms are compared to analytical and PFC3D results.

Jan 1, 2005

By John A. Herbst

Mineral processors have evolved from "handbook-based" decision makers to "model-based" decision makers. With this evolution have come significant improvements through increasing productivity, decreasing capital and operating costs and increasing product quality. This paper traces the development of model-based decision-making technology over the last 40 years and documents the benefits resulting from systems optimization using these tools. Some speculation is ventured concerning the future of model-based decision-making tools and their use in the field of mineral processing.

Jan 1, 2000

By R. I. Pennington, J. L. Vanderbeek

Investigations have been conducted at Chino Mines Co. into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on laboratory, pilot, and plant scales to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 84% with a reduction in specific energy (kWh./t) of 88%. Test results obtained to date are presented.

Jan 1, 1987