Search Documents

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991

By F. B. Henderson

1.0 PROLOG Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By M. J. Hart

There are no formulas that guarantee success when it comes to obtaining zoning approval for mineral aggregate mining. Local land use decisions often times represent the most controversial issues faced by community. Public awareness, concern, willingness to get involved, sensitivity to the environment and probably most importantly fear of change only begin to describe the atmosphere in which local land use decisions are made. Add to this the public hearing process which is quasi judicial, adversarial, and unfortunately not designed for resolution of disputes and it is not difficult to see the need for an alternative to present methods. Hopefully, some day we will have a process that will do away with or at least minimize unnecessary, unproductive and unmanageable community conflicts.

Jan 1, 1984

By Carl G. Schwenk

Rusk County is located in the northwestern portion of the state of Wisconsin, roughly 130 miles east of Minneapolis (Figure 1). The topography is generally flat with dairy farming the principal activity. Forest and swamp lands are common, as well as pasture and cultivated ground. Rusk County falls near the southern terminus of the Precambrian Shield and is covered by a thick layer of glacial drift. Outcrops are quite rare, but the few available exposures indicate that the subsurface is comprised of steeply dipping metamorphosed volcanics and sediments of Early Proterozoic age. A thin section of flatlying Cambrian sandstone is sometimes found directly under the glacial till. The depth to Precambrian basement has been recorded to be as great as 150 feet beneath the surface.

Jan 1, 1976

By L. Shwydiuk, A. Chrzanowski, W. Newcomen, G. Bastin, R. Wilkins

Automated monitoring of steep embankments allows the early detection of instability and can be used to avoid or mitigate possible slope failures. A system that uses multiple and different types of sensors has been created and successfully tested at the Highland Valley Copper mine in British Columbia. The system uses robotic total stations (RTSs) as the primary measurement sensor, with surveys repeated at predefined intervals selected to optimize operational efficiency. A methodology has been developed to improve the system’s accuracy and reliability by reducing the effects of systematic errors created by atmospheric refraction and unstable instrument and reference point positions. The inclusion of GPS sensors to monitor the RTS positions creates additional operational flexibility and maintains system integrity when insufficient reference stations are available.

Jan 1, 2003

By Kim Appleby

Epithermal gold-silver (lead-zinc-copper-manganese) mineralization on Misima Island is confined to steep and reactivated flat-lying normal faults in the upper plate of a major, shallowly dipping detachment fault. The hangingwall comprises an Eocene metavolcano-sedimentary sequence that has been extensively intruded byMiocene calc-alkaline granodiorite. It is unconformably overlain by Pliocene sedimentary and volcanic rocks. High-pressure amphibolite facies rocks dominate the footwall and have many characteristics of a metamorphic core complex. Mafic-alkalic lamprophyre dike swarms intrude the hangingwall and footwall sequences. Previous workers attributed the gold-silver mineralization on Misima to the intrusion of the porphyritic granodiorite (Williamson, 1984). This has been proposed for many tertiary gold deposits of the southwest Pacific(Sillitoe, 1989; Leach and Corbett, 1994).

Jan 1, 1996

By M. W. Chanda

This paper presents the development of a rock-creep measuring apparatus using air as the initial pressure source. Servo-controlled machines can and have been used for time-dependent property tests. However, the long-term nature of some tests makes essential the complete independence of stress-maintaining equipment from main power sources or continuously running hydraulic pumps. The main objective of this paper is the development of a creep testing machine that is free from interference arising through power supply interruptions or mechanical maintenance normally associated with many compression testing machines. To achieve this, a compressed-air power source was used to drive a compression ram. A few trial results obtained and analyzed using the transient creep law are in reasonable agreement with the general creep law.

Jan 1, 1993

By H. Cho, P. T. Luckie

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal macerals could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation was dependent upon the comminution history. Even for the same fineness, the extent of liberation might not be the same depending on how the material was generated. The liberation of coal macerals was analyzed by examining the liberation index. It was seen that, although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinite), these particles were less liberated than coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1999

By Eugene Honeycutt, David Gallagher, R. E. Melley, Nick Madison

Drummond Co. Inc.'s Shoal Creek Mine slope conveyor is the highest lift, highest horsepower, highest tension conveyor system in North America. The system has a capacity of 4950 t/h (5500 tph), a vertical lift of 360 m (1180 ft) and a total connected power of 6000 kw (8000 hp). The mine will include 2 longwall machines and 5 to 7 development sections. Annual raw production will approach 9 million tly (10 million tpy). This paper describes the early investigation of system capacity, haulage system options, and the final selection of a single flight belt conveyor. It will review the basic system de- sign and equipment selected. Also included will be some highlights of the installation of the conveyor system.

Jan 1, 1996

By J. W. Shuster

Test of trolley-diesel prime power is another step in the search to exploit the unused potential of electric wheel driven haulage trucks. The output of the present engine - a 700 horsepower diesel - is not adequate to exploit fully the 1200 horsepower potential of the two electric wheel drive motors. Power was supplied to a modified 100-ton haulage truck through a double wire trolley system. The vehicle was tested with various payloads on a 7% adverse grade haul road. More significant conclusions developed are: Power - Horsepower to propel the vehicle can he more than doubled to improve truck cycle time. Productivity - Trolley power up adverse grades can improve [producivity] rates from 18 to 36%, dependent upon haul road profile.

Jan 1, 1968

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006

By Frank P. Frandina, Diane R. Hirsch, David P. Field, Colin R. Weeks

To accommodate growth in air service and to follow the Master Plan for long-term airport development, the Metropolitan Washington Airports Authority established thed2 Development Program at Washington Dulles International Airport. A sub-surface Automated People Mover (APM) System is under construction to replace the Mobile Lounges as the primary people mover system at Dulles. To minimize disruption to airport operations the majority of the APM System’s crossings of Taxi lanes will be undertaken using Tunnel Boring Machines (TBM) or the New Austrian Tunneling Method (NATM). This paper explores the planning and design of these shallow tunnel segments for future generation aircraft loads, within the constraints of minimal construction access under post 9/11 security requirements and the context of the overall airport expansion program.

Jan 1, 2005

By Francois J. E. Scholtz, Raymond J. Davidson, Peter Greenhalgh, R. Paul Riley

A 1 t/d continuous elution pilot plan is being operated by General Mining at their Grootvlei Gold Mine using the technology developed at the Anglo American Research Laboratories. Flowsheet design and plant erection was carried out by Van Eck & Lurie and completed in December 1989. Following the conclusion of six test runs designed to optimise reagent additions, it was shown that elution efficiencies of 98-99% could be achieved using reagent additions as· low as 16 kg/ton of carbon NaCN and 28 kg/ton NaOH while consistently producing eluted carbon containing less than 50 g/t gold. Significant savings were indicated when compared and power were indicated when com­pared with the traditional batch AARL, Zadra and Micron alcohol elution procedures.

Jan 1, 1990

By David E. Peterson, F. Merz

The Waihi Gold Mining Company Limited, Martha Hill Project was the first major hard rock mining operation following the resurgence of the mining industry in New Zealand. Because of its location adjoining a town and at the southern part of the sensitive Coromandel Peninsula, the operation received a high level of public scrutiny. Very srrict limits for effluent criteria had to be met and led to the necessity for advanced wastewater rreatment technology. The process technology selected was the copper catalysed oxidation of cyanide using hydrogen peroxide, with subsequent removal of heavy metals by precipitation and filrration. This paper discusses the adoption of environment limits together with the detailed description of the plant and design criteria. Data of the one year's operational history is also presented.

Jan 1, 1991

By Bruce Cavender

Production managers look to innovative practices and equipment to reduce operating costs and improve efficiency. These innovations apply to both technical and social aspects of production operations and may be high-tech or low- tech in nature. They may be based on the implementation of a few large-scale "breakthrough projects or numerous small-scale activities, depending on the availability of capital funding and the company's past experience. Successful managers systematically identify innovative opportunities that capitalize on their organization's expertise. They quantify the associated benefits and risks and then manage the implementation of selected innovations to minimize cost and uncertainty. They monitor the results of the innovation after it has been implemented and adjust operating and managerial practices as necessary to maximize the innovation's benefit.

Jan 1, 1998

By Sepp A. Kutschera

are gaining increased interest for over­burden removal and ore production at large open cast mines. The application of bucket wheel excavators is still tied to soft un­consolidated rocks and soils, while belt conveyors can cope with all kind of matri­als restricted only by the top grain _ size. Therefore, mode of transport and the re­quirement of down stream ore processing de­fine the materials size distribution. These requirements are usually met by primary crushing or scalping. The paper discusses general applica­ tion criteria of bucket wheel excavator with systems primary for in-pit overburden crusher removal. and It _indeapits scalper units and discusses their technical and operational features. It further com­pares the capital and operating cost struc­ture relative to the syste

Jan 1, 1992

By C. A. Fleming, C. J. Ferron, P. T. O'Kane, D. B. Dreisinger

The platinum group metals (PGM's) are typically recovered by flotation, smelting of the flotation concentrate to matte, and matte leaching. Concentrates too low grade to be processed economically by the conventional process require a new treatment route. PLATSOL, a new pressure leach process, was developed for the Northmet deposit and dissolves in one step base and precious metals (PGM's and gold). Various options exist to recover all pay metals from the leach liquor. The preferred option to date involves a solid-liquid separation, followed by sulphide precipitation of gold and the PGM's, and copper solvent extraction using commercial solvent extractants. This paper briefly summarises the process and the effect of the main leach parameters. Application of the PLATSOL process to various feedstocks is also presented.

Jan 1, 2000

By G. S. P. Pereira, E. M. R. Santos

Acid mine drainage (AMD) is a serious environmental problem in mining activities. Prediction is the first step for evaluate the potential of acid generation and there are some possible methods to estimate it. They are described as static tests, which examine the balance between acid producing and acid consuming materials, and kinetic tests, which attempt to predict drainage quality overtime. Static methods are very simple and give a qualitative classification of the ores based on their potential to generate acid drainage. The characterization of ores to determine their acid producing potential is vital for the prevention of long term environmental liabilities. Laboratory tests were conducted under different methodologies to predict the acid producing potential of sulphide overburden, ore materials and tailings from a deposit of copper ore.

Jan 1, 1999

By Peter Mason, Chris Walker, Mike Costello

The Phase I electrowinning system at KCGM's Fimiston Operation utilised the well proven technology of electrowinning precious metal values onto steel wool followed by calcining and direct smelting to bullion. The above process, while reliable and successful, was to some extent labour intensive. The Williams Mine in Ontario, Canada had published conditions under which precious metal values are electrowon onto woven stainless steel and directly removed using high pressure sprays. The current paper describes the testwork which was carried out to check the applicability of the Williams criteria to KCGM eluates arising from the elution of highly loaded carbon from the calcine circuit and lowly loaded carbon from the float tails circuit. Information is also given on the commissioning and opera­tional experience which occurred.

Jan 1, 1996