Search Documents

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulphide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular S02 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, i.e., pyrrhotite, pentlandite, pyrite, chalcopyrite and violarite, have agglomerated and reacted to form two intergrown phases: pyrrhotite solid solution (FeO.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu 0.03S). Magnetite formed euhedral crystals, skeletal crystals and dendrites at the margins of the matte. Prismatic, ferrohypersthene and octahedral Mg-Al-Fe spinet crystals and dendrites are present in the glassy slag. Key words: Nickel sulfide concentrate, Iron silicate slag, Bath smelting, Mineralogy, Microscopy

Jan 1, 2003

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

By III Kimball

Mining wastes have received individual attention under the Resource Conservation and Recovery Act (RCRA) since its inception, in recognition of the special characteristics that distinguish mining wastes from other solid wastes. The Environmental Protection Agency (EPA) has recognized that: - Mining wastes are generated in much larger volumes than other industrial wastes. Most material handled in mining is waste (over 99% in many cases) and not marketable product, whereas waste is a small portion of raw materials used in most industries. Consequently, controls used for hazardous wastes may be technically infeasible or economically impractical. - Nearly all mining waste is managed at the site of generation and is land-disposed. . - Mining wastes typically pose lower hazards than other industrial wastes. Mining operations are located predominantly in sparsely populated areas and in arid or semi-arid areas with little surface water runoff and deeper water tables.

Jan 1, 1990

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2018

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2017

By W. Gibson Jaworek

It has become apparent in recent years to everyone intimately concerned with the future of the American fuels industries that the growth in demand for energy has become a topic receiving considerable attention, and that investigators are leaning more and more toward a mathematical approach to deduce what pattern that growth will follow. Though coal has been included by necessity In all-studies of future energy markets, it has not been the subject of mathematical analysis or description as frequently as has been total energy or some of the other fuels, particularly petroleum, It is the intent in this particular paper, to subject bituminous coal consumption to a preliminary mathematical scrutiny which can lead to a more logical estimation of the general level of bituminous coal consumption for the next decade, as well as formulating an approach toward describing how coal consumption may vary as the result of the annual variations in activity in the United States, economy, The approach utilized is more sophisticated than the mere projection of the historical trend of bituminous coal consumption. Such a projection would lead to a continuation of the recent decline, indicating that coal consumption would reach zero some thirty years from now. On the other hand, the mathematical analysis described here is a relatively simple, straightforward approach and- is not intended to represent the-ultimate in mathematical economic analysis as now practiced, It is hoped that this will contribute to our knowledge of bituminous coal markets. Even more, it is hoped that it will help arouse a greater interestin utilizing mathematical and statistical analysis when studying the bituminous coal industry. - Since this is a preliminary study, comments and criticisms are anticipated.

Jan 1, 1960

By George H. Davis

Much concern has been expressed recently as to whether water supplies will be sufficient to support accelerated energy development foreseen in operation Independence. Taking the Nation as a whole, sufficient water is available for energy growth, but locally, as in arid parts of the Colorado Basin, limited water supplies will dictate economies in water use and affect plant siting. As Young and Thompson1 point out with respect to electric power generation, the term "water requirements" is misleading, as demand for water for cooling is sensitive to price of water and thus is quite flexible rather than the inflexible or fixed level implied by the word "requirement." Much the same is true of other energy conversion systems. Water is used in many aspects of energy production including mining and reclamation of mined lands, on-site processing, transportation, refining, and conversion to other forms of energy. In the East, South, Midwest, and along the seacoasts, water supplies are generally adequate for energy industries; most water problems in those regions relate to pollution rather than supply. West of about the 100th meridian, however, runoff is generally less than potential diversions and energy industries must compete with alternative uses for the limited available water supplies. Water is especially short in areas of less than 10 inches mean annual rainfall where natural precipitation generally is insufficient for establishing vegetation without irrigation. Extraction. The principal categories of extraction comprise coal mining, oil and gas production, uranium mining, and oil shale mining.

Jan 1, 1974

By D. R. Hanson, H. Lawson

In this study, NIOSH researchers conducted a machine learning analysis to examine whether a model could be constructed to assess the probability of dynamic failure occurrence based on geochemical and petrographic data. Random forest, cluster analysis and dimension reduction were all applied. The objective of dimensionality reduction was to explore patterns and groupings in the data and search for relations between compositional parameters. Cluster analyses were performed to determine if an algorithm could find clusters with given class memberships and to what extent misclassifications of dynamic failure status occurred. A random forest analysis performed on data from the Pennsylvania Coal Sample Databank cross-referenced with accident data from the Mine Safety and Health Administration (MSHA) determined that 7 parameters of the 18 examined exerted the most influence on results. Cluster analysis on data after dimensionality reduction resulted in a hierarchal clustering algorithm finding four clusters, with one relatively distinct dynamic failure cluster, and three clusters consisting mostly of control group members but with a small number of dynamic failure members.

Feb 1, 2023

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By M. J. Allan, D. J. Barratt

This paper reviews current testing methods for sizing autogenom and semiautogenom mills in the North American context with comments on the necessity for test work and requirements for different circuits and equipment selection. The economics of testing and the value received are discussed.

Jan 1, 1987

By Dale C. Matthews

Pressure oxidation of refractory gold ores is becoming more popular in our environmentally sensitive society. This paper will discuss some specific process problems and solutions involved with starting up and operating an autoclave circuit.

Jan 1, 1991

By K. E. Harrison

Acid rain legislation as proposed by President Bush [1], if enacted, will immediately refocus current thinking on the economic decision-making as related to coal preparation facilities. Unit operations currently ignored because of their costs, will become mandatory to coal plant designers and operators to ensure maximum energy recovery and sulfur reduction in the entire coal stream. In anticipation of this need, the U.S. Department of Energy, The Ohio Coal Development Office, EPRI and others are sponsoring research in several areas of coal preparation, and coal plant designers are beginning to consider more innovative techniques as they configure their flowsheets for plants of the future. Preparation plants then will have recleaning

Jan 1, 1990

By Robert C. Bates

Published information discussing uranium mine radon daughter controls and related costs was examined and used to develop an estimated (projected) cost per ton for any level of control. Results show a clear power function increase of cost for conventional dilution ventilation as the annual exposure limit is lowered. Projections can be made using any assumed changes in consumer price index (CPI) and radon daughter working level months exposure limit. Bounds on the estimated costs are provided, and applicability of the final equation is discussed.

Jan 1, 1983

By Ronald L. Wiegel

Success has been achieved in developing mathematical models of rod mills, ball mills and recently to a limited extent autogenous grinding mills. There is also considerable activity in the development of mathematical models of various mineral concentration opera¬tions, such as flotation, magnetic separation and electrostatic concentration. However, at present there is a technological gap which hinders the integration of both size reduction and mineral concentration models into an overall process simulation model. This gap exists because size reduction models have been aimed at describing the size of the product and have not dealt with the equally important problem of identifying the product composition in each size fraction. Without this information the concentration model is ineffective. This situation is especially critical in the simulation of the magnetite-taconite beneficiation process, where a portion of the ore is rejected from the process following each stage of size reduction. Consideration has therefore been given to the merging of a size reduction model and a mineral liberation model to permit prediction of mineral composition as a function of size. The results of this integration of size reduction and mineral liberation models are discussed from both theoretical and practical viewpoints using batch grinding data for a magnetite iron formation sample as a demonstration vehicle.

Jan 1, 1975

By Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comninution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5 x 6.4 m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790 to 1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By J. Fuchs

This paper describes the mechanized narrow vein cut-and-fill approach used for the Deep Copper orebody at Falconbridge Limited's Strathcona Mine. Strategies for achieving high productivity while maintaining ground stability at depth and controlling dilution are discussed, including the use of mini-electrohydraulic drilling equipment, containerized truck haulage, consolidated rockfill placement techniques, and a miners' incentive system.

Jan 1, 1992

By A. Dale Wunderlich

Since Sept. 11, 2001, the author has been asked by several mining companies and mining publications to share some of his insights on how the terrorist attacks on the World Trade Center (WTC) and Pentagon might affect the mining industry globally. Until now, the author has been reluctant to express his thoughts in a publication that could possibly fall into the hands of terrorists and give them some ideas that they may not have been previously considering. However, the author discussed the contents of this article with several friends and acquaintances in the international intelligence community. They said that nothing commented on here is new to the terrorists. Potential terrorist targets Sources within the worldwide intelligence gathering community have told the author that current intelligence data indicates that it is likely that the Islamic fundamentalist groups responsible for the attacks on Sept. 11, 2001will likely be directing their effort at foreign business entities. Any overseas or any domestic businesses of highly visible companies that are part of the anti-terrorism alliance should consider themselves a potential target.

Jan 1, 2002

By John P. Weir

The planning of an underground mine for successful extraction of a bedded deposit in sedimentary rocks requires the integrated evaluation of many interdependent problems. The development and coordination of feasible solutions are the responsibility of the mining engineer. One of these problems will be discussed herein; this is the design and .layout of mine workings to secure effective control of the strata above and below the deposit. The objective is the simplest possible repetitive system permitting safe maximum recovery at optimum cost. Mining conditions to be encountered must be predictable. The best mining equipment is ineffective unless strata are controlled. Conversely, a mining layout is only of academic interest, if equipment can not be adapted to work it with adequate provision for ventilation, compliance with mining laws, proper ingress and egress and other practical requirements. Strata control, then, is but one of the mining engineer's problems, and the solutions must be worked out concurrently with solutions to other problems. Dr. Karl F. Fetters in his introductory remarks before the Fourth International Conference on Strata Control and Rock Mechanics at Columbia University said that mining engineering ?has come from the stage of empiricism backed by intuitive reasoning, to where it is based on fundamental scientific and engineering principles?. The standard curriculum in mining engineering now reflects such a change. In common with other branches of engineering education, less and less emphasis is placed on practical skills and more and more on broad scientific education. Science, research and the quest for basic truth are stressed, while descriptive courses and the teaching of specific skills are limited.

Jan 1, 1966

By C. Ceccarini, I. Salvadori, G. Oggiano

GENERAL BACKGROUND The first mention of the presence of bauxite in the mesozoic series of north-west Sardinia (fig. 1) is owed to Oosterbaan, a Dutch geologist, who carried out a geological survey of the area in the ninetten thirties. A more detailed study of the mesozoic series was attempted in the fifties by Pecorini and other, who concentrated particularly upon the stratigraphy of the bauxitic horizons, through examination of the various outcrops. In the sixties a pining company, Monte Amiata S.p.A., turned its attention to a section of the deposit outcropping near Olmedo and, considering it to be of some promise, carried out prospecting works consisting essentially of various trenches, some bore holes, a few adit and a. layout plan for the preparation and execution of trial exploitation. The results, although positive, did not convince the company's shareholders to continue the exploration. This report, which is intended as a new contribution to knowledge of the Sardinian bauxite deposit, takes into account the information acquired not only from a drilling prospection begun in 1979 in connection with the SOMIT-PROGEMISA joint venture, but also the results of structural studies and numerous chemical, mineralogical and

Jan 1, 1984

By E. J. Freech

In this part of the two-part paper we discuss briefly the adaptation of the comminution model to describe the observed behavior of an industrial grinding circuit. Although reported verification of comminution models for continuous systems is limited, some interesting work has been reported 1,2 recently. The data acquisition and modeling efforts are described first, followed by discussion of some of the simulation results. Observations pertinent to steady-state operation are presented followed by a description of the application of a dynamic model of the grinding circuit for synthesis and evaluation of grinding-circuit control. The pilot-scale work indicated the comminution model should be capable of describing an industrial size-reduction process. Recognizing the broad utility of a process model based on first- principles, the Industrial Nucleonics Corporation of Columbus, Ohio, embarked on a joint program with the Duval Corporation of Tucson, Arizona, to evaluate the industrial applicability of the models described in Part I. This program was conducted in a grinding circuit, which included a rod mill 12.5 feet in diameter and 16 feet long and a ball mill 12.5 feet in diameter and 14 feet long, at Duval Corporation's Esperanza property3. The rod mill was operated in open circuit and the ball mill in closed circuit with cyclone classifiers.

Jan 1, 1970