Search Documents

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By Daniel B. Brimhall

The research presented here was initiated to investigate the role of atmospheric oxygen in the leaching of copper waste dumps. The problem of increasing the recovery rate of copper from these dumps is or great importance considering there are by conservative estimate in excess of fifteen billion pounds of copper located in dumps in the western United States. At this time, there is an increased interest in recovering copper from these dumps on a large scale. Large tonnages of low-grade material are being placed on the waste dumps of most copper mining operations in the western United States each day. The size of these dumps ranges from 5.5 million tons at Mineral Park, Arizona, to 4 billion tons at Kennecott's Utah operation (1). Leach solutions are recycled and contain ferrous and ferric sulfates. Large quantities of dissolved aluminum, magnesium and calcium salts may also be present. To this solution make up water is added to maintain the solution inventory and sulfuric acid is added for pH adjustment. Iron is introduced into the leach solution by the dissolution of the iron-containing sulfide and oxidized minerals present in the ore deposit. In addition to the iron from dump leaching, iron is also introduced during the precipitation process when the pregnant solution is passed over metallic scrap iron if cementation is used to reduce the copper in solution.

Jan 1, 1972

By J. Kretschmann, H. Mischo, O. Drusche, S. Krause

Mining is and will be inevitable in spite of the increasing implementation of circular strategies. The energy transition and population growth will boost the demand for critical raw materials. It is the opportunity for miners to reinvent their business models. Generating attractive new business cases with sustainability-oriented innovations meets investor and stakeholder expectations from the beginning. This contribution guides managers on their pathway towards sustainable success. Contextual sustainable business model patterns will be presented that can be adjusted individually, regardless of actor’s size. It will also point out, how sustainable value creation can be measured on business model level.

Feb 1, 2023

By M. A. Vergara, J. A. Botín

"The decline of the “super cycle” has placed an end to a decade of production-focused strategies, with operating cost growing at rates higher than production. Today, the sector is placed on a tough ride and forced to shift focus to cash preservation and efficient cost management. However, most cost management systems in the minerals industry are not conceived as value driving tools but to meet financial accounting and reporting needs. This research draws from a the development of an innovative cost management methodology that applies Activity-Based Bottom-Up cost budgeting and continuous improvement tools to develop a value-driven cost management system for sustainable improvement of operational efficiency and cost reduction. The methodology was successfully tested in the Andina underground mine III Panel sector of Corporation del Cobre (CODELCO), in Chile. INTRODUCTION Cost management is fundamental to profitability of any industrial project. Even more essential in mining, an industry that deals with commodities, which prices are dictated by the market and are beyond the management capacity of the company. The end of the mining “super cycle” and the advent in 2008 of the Global Financial Crisis (GFC), placed an end to a decade of production focused strategies, with operating cost growing at rates higher than production. The sector was placed on a tough ride and forced to shift focus to cash preservation and efficient cost management. Many mining companies have seen themselves into the urgent need of cost management systems capable of achieving sustainable productivity gains and consistent profitability. Cost management is composed of three main processes: estimation, budgeting and control [1]. A number of conventional techniques have been used for cost estimation and budgeting for many years. However, most cost control systems in the minerals industry cannot be referred to as “cost management” since they are conceived to fulfil accounting and reporting needs, rather than to improve operational efficiency [2]. In general, conventional cost budgeting and control systems in mining use a “top-down” methodology, which lacks of necessary details, and fail as a management tool leading to undesirable results [3]."

Jan 1, 2016

By V. Rastogi

Acid rock drainage is the result of exposure of sulfidic materials, such as pyrites and sulfidic ores, to air and water. The oxidation of these sulfides is catalyzed by more than a million times by the bacteria Thiobacillus jerrooxidans and close families. Inhibition of these bacteria can mitigate 98% or more of the acid loading generated. This can be achieved by the use of certain surfactants that are selectively bactericidal to the lithotropic acidophilic bacteria. Bactericides are used in two ways. As periodic or continuous treatments for prevention of acidification of material actively handled and moved, and in controlled release form for reclamation where treatment sets up a change in site microbiology to replace Thiobacillus jerrooxidans with heterotrophic bacteria and creates a stable site without need for further treatments. Use of bactericides begins with laboratory testing of the site material to qualify the site for bactericide treatment and dosage determination. Site specific treatments are designed for active sites and reclamation. Once acid production is controlled, solubilization of metals is correspondingly reduced. Results and economics of use from active and reclamation sites are presented.

Jan 1, 1995

By T. McCallum, B. Wellbrook, T. Ratnaweera

"Pressure oxidation (POX) leaching of copper (Cu) concentrates continues to be explored as the next generation of leaching processes to sustain existing Cu Solvent Extraction/Electrowinning (SX/EW) operations as easily leachable ores become scarcer. The leach liquors produced, particularly from total pressure oxidation, contain elevated concentrations of Cu and acid, making solvent extraction processing more challenging. Addressing this challenge will require innovative processing techniques and continuous improvement to be successful in achieving satisfactory physical and metallurgical performance in the SX plant. The ability to efficiently process these feeds via SX plays an important role in the continued success of POX technology. Characteristics of a concentrate leach pregnant leach solution (PLS) are discussed, along with best practices that should be considered for processing by SX. Findings discussed in this paper will shed light on ways to reduce process risk and bring additional improvement to the industry with minimal change to the SX plant. INTRODUCTION Hydrometallurgical processing of copper concentrates continues to gain interest from the industry. Treatment by smelting and electro refining continues to dominate, accounting for ~80% of global copper production, but is faced with its own challenges. The case for increased hydrometallurgical processing has been discussed as high grade ore deposits are diminishing, capital costs for smelting are high, and the environmental aspects present challenges for sustainable practice. The hydromet copper industry is also turning a corner as easily leachable copper oxide deposits are depleting, and excess SX-EW capacity exists in certain regions. The transition to hydrometallurgical processing of copper concentrates will take a bit of effort as leaching of copper sulfides is difficult and byproduct credits must be considered. Various POX leaching processes have been studied and proposed to the industry as viable practices. Of the many processes, commercial use has been practiced with the Mount Gordon Copper Process, total and partial pressure oxidation by Freeport-McMoRan at their Bagdad and Morenci, Arizona complexes, the Sepon Copper Process in Laos, and the bioleach BIOCOP™ process in Chile. The experience related to the current paper centers around Cu concentrate leaching performed by Freeport McMoRan (known as CLP). The patented process was developed as an alternative to smelting and refining in 1998. The technology applies to both molybdenum and copper concentrates. Commercial CLP research and development began with Phelps Dodge in 1999 to 2001. The first commercial plant was commissioned in 2003 at the Bagdad operation. Initial operating conditions of the Bagdad CLP were under high temperature conditions before converting in 2005 to medium temperature conditions. In 2007-2009, the CLP technology was commissioned in Morenci, operating medium temperature and high temperature lite conditions until shutting down due to the economic downturn. The Morenci CLP restarted operation in April 2015 due to acid production benefits for the Morenci leach operations. Renewed solvent extraction test work initiated well before restart and has been an ongoing focus for further SX plant optimization."

Jan 1, 2018

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

By H. Majima

In spite of the importance of the presence of pyrite in the flotation of sulphide ores, not many studies have been made from the electrochemical point of view. It is generally recognized that the oxidation of sulphide minerals is one of the most Important factors among those which affect the floatability of sulphide minerals. The concept that the presence of oxygen is essential to the flotation of sulphide minerals is supported by numerous experimental results (1). The presence of oxygen in sulphide minerals- aqueous solution systems would affect the electrochemical behaviour of sulphide minerals and subsequently lead to more complicated reactions on the surface of sulphides. Actually some of the phenomena observed in sulphide flotation are deemed to be more appropriately explained from the electrochemical point of view. The author and co-workers have studied extensively the electrode reactions of pyrite and its significance in sulphide flotation. The results have been partly published elsewhere (2-7). In this paper, the author discusses the electrochemical nature of pyrite, and the three different phenomena observed in pyrite flotation: (1) Xanthate¬dixanthogen system on pyrite, (2) Flotation of complex sulphide ores containing pyrite and (3) Depressive mechanisms of pyrite with cyanide. The phenomenon which has been known as an iron contamination effect due to steel grinding media on sulphide flotation is also explained from the electrochemical aspect. However, this problem is not directly concerned with pyrite, and it will be discussed elsewhere (8).

Jan 1, 1971

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By David A. Milligan

This paper describes the Darwin Silver Recovery project, located 66 km (40 miles) outside of Lone Pine, near Darwin, Inyo County, California. A lead-zinc mine and a flotation concentrator were operated there from 1945 to 1957. By the time the mine was shut down, 1.53 Tg (1.69 million short tons) of tailings had been stored in ponds. An average silver assay of 47 mg/kg (1.38 troy oz/st) of tailings stimulated interest for commercial silver recovery. A heap leach process was developed in 1981 at the Tucson Research Center of Anaconda Minerals Company, a division of Atlantic Richfield Company. Agglomeration techniques were used on the ore since the fine grind did not allow direct heap leaching. Lime and cement were required as binders, Early laboratory tests showed that recoveries equal to those from an agitated leach could be achieved at lower capital and operating costs. Laboratory tests determined cyanide requirements, lime and cement usages, and percolation or leach rates, as well as confirming that a zinc precipitation step could recover the silver from the leach solution.

Jan 1, 1983

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By Stuart W. Maher

A major problem in future discoveries of base metals is their "explorability". By this I mean an exploration program must be designed that assures accurate assessment of the potential for ore, but is within reasonable budgetary constraints. As we are compelled to depend more and more on non-outcropping prospects, "blind" deposits, and as drilling costs multiply, the costs of exploration increase significantly. Solutions to the problem of defining exploration targets are influenced by our conceptions of the origin and recognition o f conditions that localize ore. The maxim that "elephants should be sought in elephant country" presumes we can recognize elephant country. This paper presents a suggested origin for some mineral deposits, and their controls; particularly those termed ?Mississippi Valley type". Tennessee is used as an example of the ideas offered. Mining districts designated "Mississippi Valley type" are, and have long been, the principal sources of barite, fluorite, lead and zinc ores in the United States and elsewhere throughout the world. A large volume of literature is available describing this class of ore deposits, explaining their habitat, and invoking genetic models for them. The quality of this literature is notably uneven, some of it demonstrably erroneous, and much of it is restricted to detailed descriptions of one aspect of the problem, or to detailed descriptions of one aspect of the problem, or to a single mine, or even a single stope. If an ore deposit is thought

Jan 1, 1977

By C. H. Bucknam

Acid neutralization titrations were applied to the characterization of soil and overburden for the control and prediction of acid rock drainage in the coal fields of the eastern United States in the 1970?s (1). These became known as the Sobek methods as a result of the early United States Environmental Protection Agency publication and the methods have been modified (2) to be adapted to many applications in the metal mining sector (3,4,5,6,), and, as a result, there are a large number of acid neutralization potential methods being used that are referred to as Modified Sobek methods. Standardization of neutralization potential methods for metal bearing ores and related materials based on carbonate carbon, rather than titration, commenced in the 1990?s through the American Society of Methods and Materials (ASTM) Committee E01 on Analytical Chemistry for Metal Ores and Related Materials Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials (7). A subcommittee section, E01.02.05 on Environmental Methods, was organized to coordinate the method and material standardization efforts of ASTM and the Acid Drainage Technology Initiative Metal Mining Sector (ADTI-MMS) Prediction Committee (8), which took on the project of standardization of the acid neutralization potential acidity titration method (ANPA) to supplement the carbonate carbon method in E1915 (9) for application to samples which have metal carbonates (10), in particular, which result in overestimation of the neutralization potential using the carbonate carbon methods (11).

Jan 1, 2010

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By J. H. Kempton

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes indicates that short-term predictions can bracket most parameters, uncertainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified. This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 1998

By K. Norris

The Amax Gold Guanaco mine is located in the Atacama Desert, approximately 260 km southeast of Antofagasta, Chile. The 6,000 tpd leach operation produces approximately 90,000 oz of gold, and 360,000 oz of silver per year. Production began in 1987, and the operation has been managed by Amax Gold since 1992. The mine has been plagued in the past by high operating costs and low production. Several significant changes have been made to the operations which have resulted in lower costs and higher operating efficiencies. A review of these changes is presented herein.

Jan 1, 1997

By A. D. Hammond

"INTRODUCTION The recent drop in iron ore prices has claimed an unwitting casualty in vanadium. Vanadium is dominantly produced as a co-product of steel production. The recent shutdown at EVRAZ’s Mapochs steel-vanadium operations in South Africa has cut-off 10% of the world’s vanadium output. Earlier in February, 2015, Australia’s Atlantic Ltd. suspended operations at its Windimurra iron-vanadium complex after a fire caused severe damage at the plant. Since then, challenging market conditions has resulted in the permanent closure of this operation. This decoupling of vanadium production from integrated iron ore producers presents an opportunity for vanadium exploration companies to target single-product deposits. This trend is manifested in the increasing number of pure-play vanadium ventures around the world.The mine production of vanadium is dominated by three countries namely, China, South Africa and Russia, which collectively produce 98% of the world’s vanadium. While the use of vanadium as an alloy in the steel industry remains by far the largest application for this metal, growth in demand is expected to come from the renewable energy industry in the form of batteries for energy storage. This paper summarizes the current state of vanadium exploration, briefly describes the vanadium market and lists sources of future demand for the metal. TREND IN VANADIUM EXPLORATION The most active participants in the current vanadium exploration are pure-play vanadium ventures in Brazil, South Africa and Australia. These ventures are targeting deposits with higher vanadium grade than those typically mined in titaniferous magnetite operated by integrated steel-vanadium producers. The 10% shortfall in vanadium production resulting from the shutdown at EVRAZ’s Mapochs is expected to be partially compensated by Largo Resources’ Maracás Menchen vanadium operation located in the State of Bahia in Brazil, which commenced operation in August 2014 and is expected to reach design capacity of 11,400 tonnes of vanadium pentaoxide (V2O5) by the end of 2015. The estimated production1 for 2015 is 6,500 tonnes of V2O5 at a target production cost of $3.60/lb. This is the first vanadium operation to be placed in production in the Western Hemisphere in over 35 years."

Jan 1, 2016

By Juan L. Yarmuch, Hyam Rubinstein

Open-pit mine planning is a key process in the definition of mineral reserves and their efficient removal. Ore in open-pit mines is extracted bymining sequential pits called pushbacks. Pushbacks need to satisfy complex geometrical constraints to ensure the efficient usage of equipment. To date, no algorithms that both account for those constraints and maximizeNPV, are commercially available. Therefore, pushback design is done by engineers relying on their expertise to incorporate practical features intothe output of commercial tools. In this article, we present a new algorithm that produces close to optimal practical pushbacks and we illustrate its performance in real mines.

Jun 25, 2023

By Mehmet Guney

Acceptable working environments in production areas and service openings of Mindola Mine on the Zambian Copperbelt are currently maintained with an air volume of 1000 cu m/s and 5500 kW of installed refrigeration plant. It is planned to open up additional deeper areas of the mine for future production. Temperature problems, due to the increased heat generation from various underground sources are recognized as potential hinderances to efficient production. Findings of research work indicate that the present total heat output of 58,000 kW will inevitably increase by the second five-year period of the deepening program to 52,900 kW and by the fifth five-year period to 63,200 k\V. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 53.8/40.2 °C and 35.5/42.1 °C respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 k\V This paper deals with the thermal problems in Mindola Mine, current heat output calculations, future prediction of temperature and heat load in various working areas of the mine with the application of computer programs and interpretation of data in order to find the effective solution for long-term planning of ventilation and air-conditioning.

Jan 1, 1982

By J. H. Gasper

A cost analysis for two alternative contour mining methods is performed to compare their results. The methods evaluated are: 1) Front-End Loader/Truck Haulback and 2) Scraper Haulback. Before performing these analyses, output requirements and equipment needs are found based on integrating geometric limitations with material properties. The final geometric design establishes limits on clearances, congestion problems and grades (with associated running surface materials). All calculations are kept practical, with assumptions clearly stated. The cost analysis is a unique, easily utilized compilation of several different approaches incorporating cost engineering principles. The strengths of each are welded into a cohesive entity once again aimed at practical application. The results are presented in tabular form.

Jan 1, 1992